Samsung WD90J6410AW washer dryer
Contents
1. TF Intensive For badly soiled laundry The operation time for each cycle is longer than normal ily Pre Wash e This will add a preliminary washing cycle before the main wash cycle e Bubble Soak helps remove a variety of stubborn stains e With Bubble Soak selected laundry is thoroughly soaked in Bubble Soak water bubbles for effective washing e Bubble Soak is available with and adds up to 30 minutes or 20 minutes to 3 cycles Cotton Synthetics and Baby Care e Use this option to dry the laundry for the specifiedperiod of Lo Time Dry time depending on the fibes amount of laundry quantity and moisture se this option to dry laundr h as cotton underwear and e Cupboard U option to dry laundry such as cotton unde linen D Delay End e The displayed time refers to the end time of a selected course 36 English WD80J6410AX EN indd 36 ar 2015 2 7 11 39 08 Delay End You can set the washing machine to finish our wash automatically at a later time choosing a delay of between 1 to 19 hours in 1 hour increments The hour displayed indicates the time the wash will finish 1 Select a course Then change the course settings if necessary 2 Press the Delay End button repeatedly until a desired end time is set 3 Press Start Pause button The corresponding indicator turns on with the clock running 4 To cancel the Delay End restart the washing machine by pressing the POWER b2. Press to start or stop an operation Operations 32 English WD80J6410AX EN indd 32 2015 2 7 11 39 07 Simple steps to start T2 AIR Wash 2 a P T COTTON SANITIZATION SYNTHETICS COTTON DRY WOOL SYNTHETICS DRY BABY CARE LB g Options SUPER ECO WASH OUTDOOR CARE SUPER SPEED RINSE SPIN 4 15 QUICK WASH ECO DRUM CLEAN y punts L oak 2 1 Press the Power button to turn on the washing machine 2 Turn the Course Selector to select a course 3 Change the course settings Temp Rinse Spin and Dry Level as necessary 4 To add an option press the Options button repeatedly until the corresponding option icon s turns on 5 To select a preferred mode press the Bubble Soak button repeatedly until the corresponding mode icon turns on 6 To add a frequent option press the corresponding button Delay End 7 Press the Start Pause button To change the course during operation 1 Press the Start Pause button to stop operation 2 Select a different course 3 Press the Start Pause button again to start the new course oO O D S w oO gt un English 33 WD80J6410AX EN indd 33 ar 2015 2 7 11 39 07 Operations Dry clothes only Tz AIR Wash a er SANITIZATION COTTON DRY SYNTHETICS DRY SUPER ECO WASH SUPER SPEED 15 QUICK WASH You can dry
3. Maintenance N CAUTION e Make sure the filter cap is closed properly after cleaning the filter Otherwise this may cause a leak e Make sure the filter is inserted properly after cleaning it Otherwise this may cause an operational failure or a leak Detergent Drawer 1 While holding down the release lever A on the inner of the drawer slide open the drawer 2 Remove the release lever and the liquid detergent container from the drawer 3 Clean the drawer components in flowing water using a soft brush Maintenance 4 Clean the drawer recess using a soft brush 5 Reinsert the release lever and the liquid detergent container to the drawer 6 Slide the drawer inward to close it 46 English WD80J6410AX EN indd 46 ar 2015 2 7 11 39 11 NOTE To remove remaining detergent perform the RINSE SPIN course with the drum being empty Recovery from freezing The washing machine may freeze when it drops below O C nun Turn off the washing machine and unplug the power cord Pour warm water over the water tap to loosen the water supply hose Disconnect the water supply hose and soak it in warm water Pour warm water into the drum and leave it for about 10 minutes Reconnect the water supply hose to the water tap NOTE If the washing machine still doesn t operate normally repeat the above steps until it operates normally Care against an extended time of disuse Avoid leaving the w
4. Excessive suds e Make sure the remaining amount of detergent and fabric softener is not over the limit e Make sure the Auto Dispense function is activated with both the Water Hardness and Concentration settings properly specified Cannot apply additional detergent e Plug the power cord into a live electrical outlet e Check the fuse or reset the circuit breaker e Close the door and press or tap Start Pause to start the washing machine For your safety the washing machine will not tumble or spin unless the door is closed e Before the washing machine starts to fill it will make a series of clicking noises to check the door lock and does a quick Stops drain e There may be a pause or soak period in the cycle Wait briefly and the washing machine may start e Make sure the mesh filter of the water supply hose at the water taps are not clogged Periodically clean the mesh filter e lf the washing machine is not supplied with sufficient power the washing machine temporarily will not drain or spin As soon as the washing machine regains sufficient power it will operate normally D O f WY amp Fa gt O pas 50 English WD80J6410AX EN indd 50 ar 2015 2 7 11 39 11 Problem Action e Fully open both taps e Make sure the temperature selection is correct e Make sure the hoses are connected to the correct taps Flush water lines e Make sure the water heater
5. applicable models only 1 Maintenance Ul Press and hold the Spin and Dry Level buttons simultaneously for 3 seconds to enter the Smart Check mode The washing machine starts the self diagnosis procedure and display an information code if a problem is detected Run the Samsung Smart Washer app on your mobile device and tap Smart Check Put the mobile device close to the washing machine s display so that the mobile device and the washing machine face each other Then the information code will be recognized automatically by the app When the information code is recognized correctly the app provides detailed information about the problem with applicable counteractions 40 English WD80J6410AX EN indd 40 NOTE The function name Smart Check may differ depending on the language If the washing machine reflects light on the display the app may fail to recognize the information code If the app fails to recognize the Smart Check code consecutively enter the information code manually onto the app screen 2015 2 7 11 39 09 USING DRY COURSE All drying options except for the Time Dry option detect the weight of the laundry in order to display a more accurate drying time and dry the laundry more effectively Refer to the chart below to select the appropriate drying option according to the type and amount of laundry and the moisture you want to leave Load capacity kg Mode Drying option
6. et oO 6 While holding down part E connect the water supply hose to the adaptor Then release part E The hose fits into the adaptor with a clicking sound 7 Connect the other end of the water supply hose to the inlet valve on the back of the washing machine Turn the hose clockwise to tighten English 21 WD80J6410AX EN indd 21 ar 2015 2 7 11 39 04 Installation 8 Open the water tap and check if there are any leaks around the connection areas If there are water leaks repeat the steps above ie w pan Va e f using a screw type of water tap connect the water hose to the water tap as shown N WARNING Stop using the washing machine if there is a water leak and contact a local Samsung service centre Otherwise this may cause electric shock CAUTION Do not stretch the water supply hose by force If the hose is too short replace the hose with a longer high pressure hose NOTE e After connecting the water supply hose to the adaptor check if it is connected properly by pulling the water supply hose downwards e Use a popular type of water taps If the tap is square shaped or too big remove the Spacer ring before inserting the tap into the adaptor 22 English WD80J6410AX EN indd 22 ar 2015 2 7 11 39 04 For models with an additional hot water inlet 1 Connect the red end of the hot water supply hose to the hot water inlet on the back
7. zu zu Washing Machine User manual WwD90J6 WD80J6 Sad SEC p m gt en p Safety information 3 v What you need to know about the safety instructions 3 T Important safety symbols 3 Important safety precautions 4 w Instructions about the WEEE 14 Installation 15 What s included 19 Installation requirements 17 Step by step installation 19 Before you start 25 Initial settings 25 Laundry guidelines 26 Detergent drawer guidelines 28 Operations 31 Control panel 31 Simple steps to start 33 Dry clothes only 34 Course overview 35 Settings 38 Maintenance 39 Eco Drum Clean 39 Smart Check 40 USING DRY COURSE 41 AIR WASH 42 Emergency drain 43 Cleaning 44 Recovery from freezing 47 Care against an extended time of disuse 47 Troubleshooting 48 Checkpoints 48 Information codes 53 Specifications 56 Fabric care chart 56 Protecting the environment 57 Specification sheet 58 2 English WD80J6410AX EN indd 2 ar 2015 2 7 11 39 00 zu zu Safety information Congratulations on your new Samsung washing machine This manual contains important information on the installation Use and care of your appliance Please take some time to read this manual to take full advantage of your washing machine s many benefits and features What you need to know about the safety instructions a D a D 2 lt 5 O ER 3 D md fa 5 Please read this man
8. Do not turn the appliance off by unplugging the power plug while an operation is in progress e Plugging the power plug into the wall socket again may cause a spark and result in electric shock or fire Do not let children or the infirm use this washing machine without proper supervision Do not let children climb in or onto the appliance e This may result in electric shock burns or injury Do not insert your hand or a metal object under the washing machine while it is operating e This may result in injury Do not unplug the appliance by pulling the power cord Always grip the plug firmly and pull it straight out of the outlet e Damage to the power cord may cause a short circuit fire and or electric shock Do not attempt to repair disassemble or modify the appliance yourself e Do not use a fuse such as copper steel wire etc other than a standard fuse e When the appliance needs to be repaired or reinstalled contact your nearest service centre e Failure to do so may result in electric shock fire problems with the product or injury If the water supply hose comes loose from the water tap and floods the appliance unplug the power plug e Failure to do so may result in electric shock or fire Unplug the power plug when the appliance is not being used for long periods of time or during a thunder or lightning storm e Failure to do so may result in electric shock or fire If any foreign substance enters into the applia
9. Ww D a gt lt je wn n fed ta 3 Liquid detergent container Applicable models only WD80J6410AX EN indd 29 To use a liquid detergent first put the provided liquid detergent container in the main wash detergent compartment Then apply an appropriate amount of detergent to the container Do not exceed the max line which is marked on the inner of the container CAUTION Remove the liquid detergent container if using a powder detergent English 29 F 2015 2 7 11 39 06 zu zu Before you start To use liquid detergent applicable models only First insert the provided liquid container in the ID main wash compartment Then apply liquid detergent to the container below the marked max line A N CAUTION e Do not exceed the max line that is marked inside the container e Remove the liquid container if using powder detergent Before you start 30 English WD80J6410AX EN indd 30 a 2015 2 7 11 39 06 Operations Control panel T2 AIR Wash en mp re COTTON N SANITIZATION COTTON DRY Hold 3 sec Lu w gt le Lo Ce E SER Delay End 2 o tht Litt BAe h l FF Fi paa Options mi 4 D woo D 03 04 05 07 Dry Level pe Temp Rinse Spin Legit gt m Lrg a Turn the dial to select a cycle Selector The dis
10. at 100 C max Va 2 z 1S jo Q 02 56 English WD80J6410AX EN indd 56 2015 2 7 11 39 14 Protecting the environment e This appliance is manufactured from recyclable materials If you decide to dispose of this appliance please observe local waste disposal regulations Cut off the power cord so that the appliance cannot be connected to a power source Remove the door so that animals and small children cannot get trapped inside the appliance e Do not exceed the detergent quantities recommended in the detergent manufacturer s instructions e Use stain removal products and bleaches before the wash cycle only when strictly necessary e Save water and electricity by only washing full loads the exact amount depends upon the program used 02 O D e p a et Er fe Nn English 57 WD80J6410AX EN indd 57 ar 2015 2 7 11 39 14 Specifications Specification sheet Asterisk s means variant model and can be varied 0 9 or A Z Type Front loading washing machine Model name WD90J6 WD80J6 menor W600 x D650 x W600 x D600 x H850 mm H850 mm Water pressure 50 kPa 800 kPa Water volume 63L 58L NET weight 70 kg 71 kg Wash and spin capacity 9 0 kg 8 0 kg Dry Capacity 6 0 kg 6 0 kg 220 V 100 W Washing 240 V 100 W Washing and 220 V 2000 W Bower heating 240 V 2400 W consumption 220 V 1600 W Drying 240 V 160
11. degraded Do not touch the insides of the drum or the washing machine surface during or just after drying as it may be hot This may result in burns English 41 z D gt N D 2015 2 7 11 39 09 Maintenance AIR WASH The Air Wash function refreshes garments through Samsung s unique air washing technology without the need for water Refer to the chart below for the usage and cycle time of each Air Wash cycle Cycle Usage Cycle time Deodorization Use this cycle to remove bad odors from the Sorin laundry RE Use this cycle to remove bad odors and bacteria Sanitization 59min from the laundry NOTE The recommended maximum load capacity for the Air Wash cycles is 1 kg or less one or two items If you overload the drum the deodorization or Sanitization efficiey may be reduced You can add a fragrance sheet to the laundry to add fragrance during the Air Wash cycle N CAUTION Maintenance Do not use any Air Wash cycles for the following items Heat sensitive garments made from leather mink fur silk etc Underwear trimmed with lace doll cushions and trims on dress suits may become loose Clothes trimmed with buttons can cause them to break Clothes full of starch may become deformed Hard bedding Electric blankets furry or bulky blankets Latex pillows 42 English WD80J6410AX EN indd 42 ar 2015 2 7 11 39 09 Emergency drain
12. higher than the freezing point 0 C e Away from a heat source un a 2 D et oO STEP 2 Remove the shipping bolts Unpack the product package and remove all shipping bolts 1 Loosen all shipping bolts on the rear of the machine using the supplied spanner 2 Fill the holes with the supplied plastic bolt caps Keep the shipping bolts for future use A N WARNING Packaging materials can be dangerous to children Dispose all packaging material plastic bags polystyrene etc out of children s reach English 19 WD80J6410AX EN indd 19 ar 2015 2 7 11 39 03 Installation STEP 3 Adjust the levelling feet 1 Gently slide the washing machine into position Excessive force may damage the levelling feet 2 Level the washing machine by manually adjusting the levelling feet 3 When levelling is complete tighten the nuts using the spanner je w pan Va Connect the water supply hose to the water tap 1 Remove the adaptor A from the water supply hose B 2 Use a Philips screwdriver to loosen four screws on the adaptor 20 English WD80J6410AX EN indd 20 ar 2015 2 7 11 39 03 3 Hold the adaptor and turn part C in the arrow direction to loosen it by 5 mm 4 Insert the adaptor into the water tap and tighten the screws while lifting Up the adaptor 5 Turn part C in the arrow direction to tighten it gt un a 2 D
13. of the machine 2 Connect the other end of the hot water supply hose to the hot water tap un a 2 D et oO The aqua hose alerts users of a risk of water leaks It senses the water flow and turns red on the centre indicator A in case of a leak English 23 WD80J6410AX EN indd 23 ar 2015 2 7 11 39 04 Installation STEP 5 Position the drain hose The drain hose can be positioned in three ways Over the edge of a wash basin The drain hose must be placed at a height of between 60 cm and 90 cm from the floor To keep the spout of the drain hose bent use the supplied plastic hose guide A Secure the guide to the wall using a hook to ensure stable drainage je w u Va In a sink drain pipe The drain pipe must be above the sink siphon so that the end of the hose is at least 60 cm above the floor In a drain pipe The drain pipe should be between 60 cm and 90 cm high It is advisable to use a 65 cm high vertical pipe Make sure the drain hose is connected to the stand pipe at a Slant Drain standpipe requirements e Minimum diameter of 5 cm e Minimum carry away capacity of 60 litres per minute STEP6 Turn on the washing machine Plug the power cord into a wall socket featuring an AC 220 240 V 50 Hz approved electrical outlet protected by a fuse or circuit breaker Then press the Power button to turn on the washing machine 24 English WD80J641
14. sort them accordingly before starting the wash 26 English WD80J6410AX EN indd 26 Empty all the pockets of your laundry items e Metal objects such as coins pins and buckles on clothing may damage other laundry items as well as the drum Turn clothing with buttons and embroideries inside out e If pants or jacket zippers are open while washing the drum may be damaged Zippers should be closed and fixed with a string e Clothing with long strings may become entangled with other clothes Make sure to tie the strings before starting the wash STEP 3 Usea laundry net e Brassieres water washable must be placed in a laundry net Metal parts of the brassieres may break through and tear other laundry items e Small light clothing such as socks gloves stockings and handkerchiefs may become caught around the door Place them inside a fine laundry net e Do not wash the laundry net by itself without other laundry This may cause abnormal vibrations that could move the washing machine and result in injury 2015 2 7 11 39 05 WD80J6410AX EN indd 27 STEP 4 Prewash if necessary Select the Prewash option for the selected course if the laundry is heavily soiled Do not use the Prewash option when detergent is manually added into the drum STEP 5 Determine the load capacity Do not overload the washing machine Overloading may cause the washing machine to not wash properly For the load capacity fo
15. will not tumble or spin unless the door Does not drain and or is closed spin e Make sure the drain hose is not frozen or clogged e Make sure the drain hose is connected to a drain system that is not clogged e Ifthe washing machine is not supplied with sufficient power the washing machine temporarily will not drain or spin As soon as the washing machine regains sufficient power it will operate normally e Press or tap Start Pause to stop the washing machine fe er m 1 Sr e a 5 a e t may take a few moments for the door lock mechanism to disengage e The door will not open until 3 minutes after the washing The door does not machine has stopped or the power turned off open e Make sure all the water in the drum is drained e The door may not open if water remains in the drum Drain the drum and open the door manually e Make sure the door lock light is off The door lock light turns off after the washing machine has drained English 49 WD80J6410AX EN indd 49 a 2015 2 7 11 39 11 zu zu Troubleshooting Problem Action e Make sure the Auto Detergent and Auto Softener settings are properly configured e Make sure you use the recommended types of detergent as appropriate e Use high efficiency HE detergent to prevent oversudsing e Reduce the detergent amount for soft water small loads or lightly soiled loads e Non HE detergent is not recommended
16. 0 W Spin 220 240 V 450 W Pumping 30 W Spin revolutions 1400 rpm NOTE purposes Va Q i 1S 1S oD a WN 58 English WD80J6410AX EN indd 58 The design and specifications are subject to change without notice for quality improvement 2015 2 7 11 39 14 According to Regulation EU No 90 60 EC Asterisk s means variant model and can be varied 0 9 or A Z Programs to which the information on the label Samsung Model Name wbs0J6 WD80J6 Energy Efficiency Class A highest efficient to G lowest efficient A A Energy Consumption Washing spinning and drying kwh 6 12 5 44 Washing and spinning only kwh 1 17 1 04 Washing Performance Class A highest efficient to G lowest efficient A A Water Extraction Efficiency Class A highest efficient to G lowest efficient A A Residual moisture 44 44 Maximum Spin Speed rpm 1400 1400 Capacity Washing kg 9 8 Drying kg 6 6 Water Consumption Washing spinning and drying l 99 88 Washing and spinning only t 54 44 Program Duration Washing spinning and drying min 592 517 Washing and spinning only min 262 262 Wash Cotton 60 C Intensive WD80J6410AX EN indd 59 and the Sheet relate Dry Cotton Dry Cup board Estimatd annual consumption for a 4 person household always using the dries 200 cyc
17. 0AX EN indd 24 ar 2015 2 7 11 39 05 zu zu Before you start Initial settings Run Calibration recommended Calibration ensures accurate weight detection by the washing machine Make sure the drum is empty before running Calibration 1 WD80J6410AX EN indd 25 ar Power off and then power on the washing machine Hold down Temp and Delay End Simultaneously for 3 seconds to enter Calibration mode The CB message appears Press Start Pause to run the Calibration cycle The drum will rotate clockwise and counter clockwise for about 3 minutes When the cycle is complete O appears on the display and the washing machine will turn off automatically The washing machine is now ready for use Ww D a gt lt eo wn T fed ta 3 English 25 2015 2 7 11 39 05 Before you start zu zu Before you start Laundry guidelines STEP 1 Sort STEP 2 Empty pockets Sort the laundry according to these criteria e Care Label Sort the laundry into cottons mixed fibres synthetics silks wools and rayon e Colour Separate whites from colours e Size Mixing different sized items together in the drum improves the washing performance e Sensitivity Wash delicate items separately using an Easy Iron option for pure new woollen items curtains and silk items Check the labels on the items NOTE Make sure to check the care label on the clothing and
18. CARE made of functional materials such as spandex stretch 2 2 and micro fibre RINSE SPIN Featuring an additional rinse after applying fabric r softener to the laundry Cleans the drum by removing dirt and bacteria from the drum ECO DRUM CLEAN Perform once every 40 washes with no detergent or bleach applied Make sure the drum is empty Do not use any cleaning agents for cleaning the drum This course is useful for removing bad odors Turning the Cycle Selector cycles through the following AIR WASH operating modes Deodorization gt Sanitization i Deodorization Reduces bad smells from the laundry Sanitization Deodorize and sanitize the laundry by stronger AIR Wash action with higher temp English 35 2015 2 7 11 39 08 Operations Course Description amp Max load kg COTTON DRY ro dry laundry such as cotton underwear and SYNTHETICS DRY e Use to dry heat sensitive garments This protects the i fibers of the garment by dying it at low temperatures e Low temperature Eco Bubble contributes to power SUPER ECO WASH f 4 saving e Press this button if you need to shorten the washing time applicable for Intensive Pre Wash or Delay End SUPER SKEER cycles The shortened time may differ depending on i the Cycle Load Option 15 QUICK WASH e For lightly soiled garments in less than 2 0 kg that you 5 want to wash quickly 5 Options w 5 Fa Option Description a
19. In case of a power failure drain the water inside the drum before taking out the laundry 1 Power off and unplug the washing machine from the electrical outlet 2 Open the filter cover A using a coin or thin metal object 3 Put an empty spacious container around the cover and stretch the emergency drain tube to the container while holding the tube cap B lt D D N D 4 Open the tube cap and let water in the tube C flow into the container 5 When done close the tube cap and reinsert the tube Then close the filter cover NOTE Use a spacious container because the water in the drum may be more than expected English 43 WD80J6410AX EN indd 43 a 2015 2 7 11 39 09 Maintenance Cleaning Surface of the washing machine Use a soft cloth with a nonabrasive household detergent Do not spray water onto the washing machine Mesh filter Clean the mesh filter of the water supply hose once or twice a year 1 Turn off the washing machine and unplug the power cord 2 Close the water tap 3 Loosen and disconnect the water supply hose from the back of the washing machine Cover the hose with a cloth to prevent water from gushing out 4 Use pliers to pull out the mesh filter from the inlet valve hole 5 Submerge the mesh filter deeply in water so that the threaded connector is also submerged 6 Dry the mesh filter completely in the Shade 7 Reinsert the mesh filte
20. Usage Cotton Dry Synthetics Dry 5 Use this option to dry laundry such Aufo bryung BT Cupboard as cotton underwear and linen 5kg 3 kg Use this option to dry the laundry 30 270 min 30 270 min Manual Drying ay fF INNE sPeclited peiod of time in 30 minutes in 30 minutes Time Dry depending on the fibes amount of increments increments laundry quantity and moisture NOTE The drying result may differ depending on the selected washing cycle and the CAUTION Do not use the drying function after type amount of laundry e If both washing and drying cycles are selected the spin speed is automatically set to enhance the drying efficiency e Incase you want to dry laundry after a hand wash turn the cycle selector to select the spin cycle and then select a drying option for best performance e When drying is complete dust from the dry surface of the clothes may remain on the diaphragm due to the ironing effect that prevents wrinkles The dus will be washed away during the following wash Alternatively you can easily remove it with a damp towel or cloth WD80J6410AX EN indd 41 applying a chlorine bleach agent to the laundry during a wash or drying cycle Otherwise the laundry may become discolored or the material may be damaged Do not use the drying function for clothing with fur lining or made from acrylic material This may result in the drying function being
21. arting the cycle e Ifthe information code remains contact a customer service centre If any information code keeps appearing on the screen contact a local Samsung service centre WD80J6410AX EN indd 55 5 je S oO D 1 2 e je ep Ce English 55 2015 2 7 11 39 11 Specifications Fabric care chart The following symbols provide garment care directions The care labels include four symbols in this order washing bleaching drying and ironing and dry cleaning when necessary The use of symbols ensures consistency among garment manufacturers of domestic and imported items Follow the care label directions to maximize garment life and reduce laundry problems 7 Resistant material DA Do not iron w Delicate fabric Can be dry cleaned using any solvent Item can be washed at 95 C O Dry Clean Dry clean with perchloride Item can be washed at 60 C P lighter fuel pure alcohol or R113 only ieme ba washed st 40eC Dry clean with aviation fuel pure alcohol or R113 only Item can be washed at 30 C amp Do not dry clean Hand wash only Dry flat DT Dry clean only Mm Can be hung to dry A Can be bleached in cold water m Dry on clothes hanger A Do not bleach Tumble dry normal heat Can be ironed at 200 C max Tumble dry reduced heat A Can be ironed at 150 C max RI Do not tumble dry A Can be ironed
22. ashing machine and to prevent accidents when doing laundry What s included Make sure all the parts are included in the product package If you have a problem with the washing machine or the parts contact a local Samsung customer centre or the retailer 01 Release lever 04 Door 07 Emergency drain tube 10 Power plug WD80J6410AX EN indd 15 02 Detergent drawer 05 Drum 08 Filter cover 11 Drain hose 03 Control panel 06 Lint filter 09 Worktop 12 Levelling feet un a 2 D et oO English 15 2015 2 7 11 39 02 Installation Spanner Hose guide ie T pan Va Cold water hose Hot water hose Liquid detergent container Cap fixer NOTE e Bolt caps The provided number 3 to 6 of bolt caps depends on the model e Hot water supply hose Applicable models only e Liquid detergent container Applicable models only 16 English WD80J6410AX EN indd 16 a 2015 2 7 11 39 02 WD80J6410AX EN indd 17 Installation requirements Electrical supply and grounding e AC 220 240 V 50 Hz fuse or circuit breaker is required e Use an individual branch circuit specific to the washing machine To ensure proper grounding the washing machine comes with a power cord featuring a three prong grounding plug for use ina properly installed and grounded outlet Check with a qualified electrician or serviceperson if you are not sure about
23. ashing machine unused for an extended time If this is the case drain the washing machine and unplug the power cord 1 URUN WD80J6410AX EN indd 47 ar Turn the Course Selector to select a RINSE SPIN Empty the drum and press Start Pause button When the course Is complete close the water tap and disconnect the water supply hose Turn off the washing machine and unplug the power cord Open the door to let air circulate through the drum D gt N D English 47 2015 2 7 11 39 11 zu zu Troubleshooting Checkpoints If you encounter a problem with the washing machine first check the table below and try the suggestions Problem Action e Make sure the washing machine is plugged in e Make sure the door is properly closed e Make sure the water taps are open e Make sure to press or tap Start Pause to start the washing machine e Make sure Child Lock is not activated e Before the washing machine starts to fill it will make a series of clicking noises to check the door lock and does a quick drain e Check the fuse or reset the circuit breaker Does not start e Fully open the water tap Water supply is e Make sure the door is properly closed insufficient or no e Make sure the water supply hose is not frozen water is supplied e Make sure the water supply hose is not kinked or clogged e Make sure there is sufficient water pressure e Make s
24. ble models only is not used for powder detergent Remove the guide when using powder detergent Do not place any objects such as shoes food waste animals other than laundry into the washing machine e This may result in damage to the washing machine or injury and death in the case of pets due to the abnormal vibrations 12 English WD80J6410AX EN indd 12 ar 2015 2 7 11 39 01 Do not press the buttons using sharp objects such as pins Knifes fingernails etc e This may result in electric shock or injury Do not wash laundry contaminated by oils creams or lotions Usually found in skincare shops or massage clinics e This may cause the rubber seal to become deformed and result in a water leak a D a D 2 lt 5 O 3 D md a 5 Do not leave metal objects such as safety pins hair pins or bleach in the drum for long periods of time e This may cause the drum to rust e f rust starts appearing on the surface of the drum apply a neutral cleansing agent to the surface and use a sponge to clean it Never use a metal brush Do not use dry cleaning detergent directly and do not wash rinse or spin laundry contaminated by dry cleaning detergent e This may result in spontaneous combustion or ignition due to the heat from the oxidation of the oil Do not use water from water cooling heating devices e This may result in problems with the washing machine Do not use natural hand washing soap
25. e va Do not pull or excessively bend the power cord Do not twist or tie the power cord Do not hook the power cord over a metal object place a heavy object on the power cord insert the power cord between objects or push the power cord into the space behind the appliance e This may result in electric shock or fire Do not pull the power cord when unplugging the power plug e Unplug the power plug by holding the plug e Failure to do so may result in electric shock or fire 8 English WD80J6410AX EN indd 8 a 2015 2 7 11 39 01 Installation cautions CAUTION This appliance should be positioned in such a way that the power plug is easily accessible e Failure to do so may result in electric shock or fire due to electric leakage 0 D a D 2 lt 5 O 3 D md a 5 Install your appliance on a solid level floor that can support its weight e Failure to do so may result in abnormal vibrations movement noise or problems with the product Critical Usage warnings J N WARNING If the appliance is flooded turn off the water amp power supplies immediately and contact your nearest service centre e Do not touch the power plug with wet hands e Failure to do so may result in electric shock If the appliance generates a strange noise a burning smell or smoke unplug the power plug immediately and contact your nearest service centre e Failure to do so may result in elect
26. e dryer door is restricted For use in Europe Children of less than 3 years should be kept away Unless continuously supervised 6 English WD80J6410AX EN indd 6 ar 2015 2 7 11 39 01 Critical installation warnings 0 eb T N WARNING The installation of this appliance must be performed by a qualified technician or service company a e Failure to do so may result in electric shock fire an explosion problems with the product 2 or injury The appliance is heavy therefore take care when lifting it Plug the power cord into an AC 220 240 V 50 Hz wall socket or higher and use the socket for this appliance only Never use an extension cord e Sharing a wall socket with other appliances using a power strip or extending the power cord may result in electric shock or fire e Ensure that the power voltage frequency and current are the same as those of the product specifications Failure to do so may result in electric shock or fire Plug the power plug into the wall socket firmly Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis e Unplug the power plug and clean it with a dry cloth e Failure to do so may result in electric shock or fire e Plug the power plug into the wall socket so that the cord is running towards the floor If you plug the power plug into the socket in the opposite direction the electric wires withi
27. ed items in the tumble dryer Items that have been soiled with substances such as cooking oil acetone alcohol petrol Kerosene spot removers turpentine waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the tumble dryer English 5 WD80J6410AX EN indd 5 ar 2015 2 7 11 39 01 zu zu Safety information Items such as foam rubber latex foam shower caps waterproof textiles rubber backed articles and clothes or pillows fitted with foam rubber pads should not be dried in the tumble dryer Fabric softeners or similar products should be used as specified by the fabric softener instructions Cc oO ge ie ru S gt pe ru ge va The final part of a tumble dryer cycle occurs without heat cool down cycle to ensure that the items are left at a temperature that ensures that the items will not be damaged Remove all objects from pockets such as lighters and matches N WARNING Never stop a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated Exhaust air must not be discharged into a flue which is used for exhausting fumes from appliances burning gas or other fuels The appliance must not be installed behind a lockable door a sliding door or a door with a hinge on the opposite side to that of the tumble dryer in such a way that a full opening of the tumbl
28. for the washing machine e f it hardens and accumulates inside the washing machine it may result in problems with the product discolouration rust or bad odours Place socks and brassieres in a washing net and wash them with the other laundry Do not wash large laundry items such as bedding in the washing net e Failure to do so may result in injury due to abnormal vibrations Do not use hardened detergent e If it accumulates inside the washing machine it may result in a water leak Make sure that the pockets of all the clothing items to be washed are empty e Hard sharp objects such as coins safety pins nails screws or stones can cause extensive damage to the appliance Do not wash clothing with large buckles buttons or other heavy metal objects Sort the laundry by color on the basis of its colorfastness and select the recommended cycle water temperature and additional functions e This may result in discoloration or fabric damage Take care that children s fingers are not caught in the door when you close it e Failure to do so may result in injury English 13 WD80J6410AX EN indd 13 ar 2015 2 7 11 39 01 zu zu Safety information Critical cleaning warnings N WARNING Do not clean the appliance by spraying water directly onto it Do not use the a strong acidic cleaning agent Cc oO ge ie ye S gt pe ru ge va Do not use benzene thinner or alcohol to clean the appl
29. iance e This may result in discolouration deformation damage electric shock or fire Before cleaning or performing maintenance unplug the appliance from the wall socket e Failure to do so may result in electric shock or fire Instructions about the WEEE Correct Disposal of This Product Waste Electrical amp Electronic Equipment Applicable in countries with separate collection systems This marking on the product accessories or literature indicates that the product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic accessories should not be mixed with other commercial wastes for disposal 14 English WD80J6410AX EN indd 14 ar 2015 2 7 11 39 01 Installation zu zu Follow these instructions carefully to ensure proper installation of the w
30. is set to supply a minimum 120 F 49 C hot water at the tap Also check the water heater capacity and recovery rate e Disconnect the hoses and clean the mesh filter The mesh filter Fills with the wrong may be clogged water temperature e While the washing machine fills the water temperature may change as the automatic temperature control feature checks incoming water temperature This is normal e While the washing machine fills you may notice just hot and or just cold water going through the dispenser when cold or warm temperatures are selected This is anormal function of the automatic temperature control feature as the washing machine determines the water temperature e Use the High or Extra High spin speed e Use high efficiency HE detergent to reduce oversudsing e Load is too small Small loads one or two items may become unbalanced and not spin completely e Make sure the drain hose is not kinked or clogged Load is wet at the end of a cycle e Make sure the door is properly closed e Make sure all hose connections are tight e Make sure the end of the drain hose is correctly inserted and secured to the drain system e Avoid overloading e Use high efficiency HE detergent to prevent oversudsing Leaks water fe er m 1 Sr fo a ct 5 a e Excessive suds collect in recesses and can cause fou odours e Run cleansing cycles to sanitize periodically e Clean the door sea
31. k state you must first deactivate the Child Lock Operations 38 English WD80J6410AX EN indd 38 a 2015 2 7 11 39 09 zu zu Maintenance Keep the washing machine clean to prevent deteriorated performance and to preserve its life cycle Eco Drum Clean Perform this course regularly to clean the ECO DRUM CLEAN reminder drum and to remove bacteria from it e The ECO DRUM CLEAN reminder appears 1 Press the Power button to turn on on the main screen once every 40 washing machine washes It is advisable to perform the 2 Turn the Course Selector to select ECO ECO DRUM CLEAN regularly DRUM CLEAN e When you first see this reminder 3 Press the Start Pause button you can ignore the reminder for 6 consecutive times From the 7th wash NOTE the reminder does not appear However The water temperature for ECO DRUM it appears again on the second 40th CLEAN is set to 70 C which cannot be wash changed CAUTION Do not use any cleaning agents for cleaning the drum Chemical residue in the drum deteriorates the washing performance D gt N D English 39 WD80J6410AX EN indd 39 ar 2015 2 7 11 39 09 Maintenance Smart Check To enable this function you must first download the Samsung Smart Washer at the Play Store or the Apple Store and install it on a mobile device featuring the camera operation The Smart Check function has been optimized for Galaxy amp iPhone series
32. l diaphragm e Dry the washing machine interior after a cycle has finished Has odours No bubbles are seen Bubbleshot models only e Overloading may screen bubbles e Severely contaminated laundry may not generate bubbles English 51 WD80J6410AX EN indd 51 a 2015 2 7 11 39 11 zu zu Troubleshooting Problem Action e Make sure the Internet connection to your house is properly established e Make sure the router turns on and operates normally e Make sure you have installed the latest version of the Smart Control App Wi Fi does not work Wi Fi models only If a problem persists contact a local Samsung service centre D a is W a 2 fa pas 52 English WD80J6410AX EN indd 52 a 2015 2 7 11 39 11 Information codes If the washing machine fails to operate you may see an information code on the screen Check the table below and try the suggestions Problem Action Water is not supplied Make sure the water taps are open Make sure the water hoses are not clogged Make sure the water taps are not frozen Make sure the washing machine is operating with sufficient Ww M ater pressure ake sure that the cold water tap and the hot water tap are 4c properly connected e Clean the mesh filter as it may be clogged NOTE When the washer displays the 4C code the washer do draining for 3 minutes During
33. laundry is spread out evenly e Make sure the washing machine is on a flat stable surface UB e Redistribute the load If only one item of clothing needs washing such as a bathrobe or pair of jeans the final spin result might be unsatisfactory and an UB check message will be shown in the display Check the motor for operation 3C e Try restarting the cycle e ifthe information code remains contact a customer service centre The electronic control needs to be checked Over Voltage Error e Check the PCB and wire harness e Check if power is supplied properly e Ifthe information code remains contact a customer service D UC centre 8 Low voltage detected T e Check if the power cord is plugged in eb R 3 R i Fa e ifthe information code remains contact a customer service centre High temperature heating check HC e ifthe information code remains contact a customer service centre 54 English WD80J6410AX EN indd 54 ar 2015 2 7 11 39 11 Problem Action The Water Level sensor is not working properly e Try power off and restarting the cycle e Check Water Level Sensor wire harness e Ifthe information code remains contact a customer service centre 1C NOTE When the washer displays the 1C code the washer do draining for 3 minutes During this time the Power button is inoperative Check communications between main and sub PBAs AC e Try power off and rest
34. les Energy Consumption kWh yr 1224 1088 Water Consumption t 19800 17600 Estimatd annual consumption for a 4 person household never using the drier 200 cycles a Energy Consumption kWh yr 234 208 a Water Consumption t 10800 9600 D eh O 5 9 English 59 2015 2 7 11 39 14 Ce QUESTIONS OR COMMENTS COUNTRY CALL OR VISIT US ONLINE AT UK 0330 SAMSUNG 7267864 www samsung com uk support A ae DC68 03591A 00_EN WD80J6410AX EN indd 60 ar 2015 2 7 11 39 15
35. llation Flooring For best performance the washing machine must be installed on a solid floor Wood floors may need to be reinforced to minimize vibration and or unbalanced loads Carpeting and soft tile surfaces are not a good resistance to vibrations and may cause the washing machine to move slightly during the spin cycle N CAUTION Do NOT install the washing machine ona platform or a poorly supported structure Water temperature Do not install the washing machine in areas where water may freeze as the washing machine always retains some water in its water valves pumps and or hoses Frozen water left in the connection parts may cause damage to belts the pump and other components of the washing machine 18 English WD80J6410AX EN indd 18 Alcove or closet installation Minimum clearance for stable operation 50 mm 550 mm Sides 25 mm Rear Top 25 mm Front If both the washing machine and a dryer are installed in the same location the front of the alcove or closet must have at least a 550 mm unobstructed air opening Your washing machine alone does not require a specific air opening 2015 2 7 11 39 02 Step by step installation STEP 1 Select a location Location requirements e Solid level surface without carpeting or flooring that may obstruct ventilation e Away from direct sunlight e Adequate room for ventilation and wiring e The ambient temperature is always
36. n the cable may be damaged and this may result in electric shock or fire Keep all packaging materials out of the reach of children as these may be dangerous e If achild places a bag over its head it may suffocate When the appliance power plug or power cord is damaged contact your nearest service centre This appliance must be properly grounded Do not ground the appliance to a gas pipe plastic water pipe or telephone line e This may result in electric shock fire an explosion or problems with the product e Never plug the power cord into a socket that is not grounded correctly and make sure that it is in accordance with local and national regulations Do not install this appliance near a heater or any inflammable material Do not install this appliance in a humid oily or dusty location or in a location exposed to direct sunlight or water rain drops Do not install this appliance in a location exposed to low temperatures e Frost may cause the tubes to burst English 7 WD80J6410AX EN indd 7 ar 2015 2 7 11 39 01 zu zu Safety information Do not install this appliance in a location where gas may leak e This may result in electric shock or fire Do not use an electric transformer e This may result in electric shock or fire Do not use a damaged power plug damaged power cord or loose wall socket e This may result in electric shock or fire Cc oO ge ie ru S gt pe ru g
37. nce unplug the power plug and contact you nearest Samsung Customer Service e This may result in electric shock or fire 10 English WD80J6410AX EN indd 10 ar 2015 2 7 11 39 01 Usage cautions CAUTION When the washing machine is contaminated by a foreign substance such as detergent dirt food waste etc unplug the power plug and clean the washing machine using a damp soft cloth e Failure to do so may result in discolouration deformation damage or rust 0 D a D 2 lt 5 O 3 D md a 5 The front glass may be broken by a strong impact Take care when using the washing machine e ifthe glass is broken it may result in injury After a water supply failure or when reconnecting the water supply hose open the water tap slowly Open the water tap slowly after a long period of non use e The air pressure in the water supply hose or the water pipe may damage a product part or result in a water leak If a draining error occurs during an operation check if there is a draining problem e f the washing machine is used when it is flooded because of a draining problem it may result in electric shock or fire Insert the laundry into the washing machine completely so that the laundry does not get caught in the door e If laundry gets caught in the door it may result in damage to the laundry or the washing machine or result in a water leak Turn the water supply off when the washing machine is not bei
38. ng used Ensure that the screws on the water supply hose connector are properly tightened e Failure to do so may result in property damage or injury Ensure that the rubber seal and front door glass are not contaminated by a foreign substance e g waste thread hair etc e Ifa foreign substance is caught in the door or the door is not completely closed it may cause a water leak Open the water tap and check if the water supply hose connector is firmly tightened and that there is no water leak before using the product e f the screws on the water supply hose connector are loose it may result in a water leak The product you have purchased is designed for domestic use only English 11 WD80J6410AX EN indd 11 a 2015 2 7 11 39 01 zu zu Safety information Using the product for business purposes qualifies as a product misuse In this case the product will not be covered by the standard warranty provided by Samsung and no responsibility can be attributed to Samsung for malfunctions or damages resulting from such misuse Do not stand on the appliance or place objects such as laundry lighted candles lighted cigarettes dishes chemicals metal objects etc on the appliance e This may result in electric shock fire problems with the product or injury Cc oO gt ge ie ye gt w eu ge va Do not spray volatile material such as insecticide onto the surface of the appliance e As well a
39. play shows current cycle information and estimated time 02 Display ee remaining or an information code when a problem occurs 03 Temp Press to change the water temperature for the current cycle Press to change the rinse times for the current course 04 Rinse A You can set the rinse times up to 5 Press to change the spinning speed for the current cycle e Rinse Hold 7 The final rinse process is suspended so that the 05 Spin laundry remains in the water To unload the laundry run a drain or spin process e No Spin The drum does not spin after the final drain process 06 Dry Level Press this button to select proper drying option 07 Bubble Soak Press to activate deactivate the Bubble Soak function This function helps remove a wide variety of stubborn stains Press to select an Option from Intensive Prewash and 08 Options Intensive Prewash Press again to deselect WD80J6410AX EN indd 31 English Oo oe 5 e3 oO Nn 31 2015 2 7 11 39 07 Operations Delay End lets you set the end time of the current cycle Based on your settings the start time of the cycle will be determined by the machine s internal logic For example this setting is useful for we Dey aie programming your machine to finish a wash at the time you normally return home from work e Press to choose a preset unit of hours 10 Power Press to turn on off the washing machine 11 Start Pause
40. r into the water supply hose and place the water supply hose in the original position 8 Open the water tap Maintenance NOTE If the mesh filter is clogged an error code of 4C appears on the screen 44 English WD80J6410AX EN indd 44 ar 2015 2 7 11 39 10 Debris filter It is advisable to clean the debris filter 5 or 6 times a year to prevent its clogging A clogged debris filter may reduce the bubble effect 1 Turn off the washing machine and unplug the power cord 2 Drain the remaining water inside the drum drum See the Emergency drain section 3 Open the filter cover using a coin or key 4 Turn the pump filter A knob to the left and drain off the remaining water 5 Clean the pump filter using soft brushes Make sure the drain pump propeller inside the filter is unclogged 6 Reinsert the pump filter and turn the filter knob to the right D gt N D NOTE Some pump filters feature a safety knob that is designed to prevent accidents by children To open the safety knob of the pump filter push in and turn it anticlockwise The spring mechanism of the safety knob helps open the filter e To close the safety knob of the pump filter turn it clockwise The spring makes a rattling sound which is normal NOTE If the debris filter is clogged an error code of 5C appears on the screen English 45 WD80J6410AX EN indd 45 ar 2015 2 7 11 39 10
41. r the type of clothing see page 35 NOTE When washing bedding or bedding covers the wash time may be lengthened or the spin efficiency may be reduced For bedding or bedding covers the recommended maximum spin cycle speed is 800 rpm and the load capacity is 2 0 kg or less N CAUTION If the laundry is unbalanced and the UE error code is displayed redistribute the load Unbalanced laundry may reduce the spinning performance STEP 6 Apply a proper detergent type The type of detergent depends on the type of fabric cotton synthetic delicate items wool colour wash temperature and degree of soiling Always use low suds laundry detergent which is designed for automatic washing machines N NOTE Follow the detergent manufacturer s recommendations based on the weight of the laundry the degree of soiling and the hardness of the water in your local area If you are not sure about the water hardness contact a local water authority e Do not use detergent that tends to be hardened or solidified This detergent may remain after the rinse cycle blocking the drain outlet CAUTION When washing wool using the wool course use only a neutral liquid detergent If used with the Wool course powder detergent may remain on the laundry and discolour the laundry English Ww D a gt lt je wn T fed ta 3 27 2015 2 7 11 39 05 zu zu Before you start Dete
42. rgent drawer guidelines The washing machine provides a three compartment dispenser the left compartment for the main wash the front right for fabric softeners and the rear right for the preliminary wash 01 Prewash detergent compartment 02 Main wash detergent compartment powder detergents water softeners pre soaking agents bleach and stain removers 03 Fabric softener compartment Before you start CAUTION e Do not open the detergent drawer while the washing machine is operating e Do not use the following types of detergent e Tablet or capsule types e Ball or net types e To prevent the compartment clogging concentrated or highly enriched agents fabric softener or detergent must be diluted with water before being applied The detergent drawer is located at the top left corner of the washing machine 1 Slide open the detergent drawer 2 Apply laundry detergent to the main wash compartment as instructed or recommended by the manufacturer To use liquid detergent see page 31 28 English WD80J6410AX EN indd 28 ar 2015 2 7 11 39 06 3 Apply an appropriate amount of fabric softener to the front right compartment if necessary Do not exceed the max line A which is marked on the compartment 4 If selecting the Prewash option apply an appropriate amount of detergent to the rear right compartment o 5 Slide the detergent drawer inward to close it
43. ric shock or fire In the event of a gas leak such as propane gas LP gas etc ventilate immediately without touching the power plug Do not touch the appliance or power cord e Do not use a ventilating fan e A spark may result in an explosion or fire Do not let children play in or on the washing machine In addition when disposing of the appliance remove the washing machine door lever e lf trapped inside the product children may suffocate to death Make sure to remove the packaging sponge styrofoam attached to the bottom of the washing machine before using it Do not wash items contaminated with gasoline kerosene benzene paint thinner alcohol or other inflammable or explosive substances e This may result in electric shock fire or an explosion Do not open the washing machine door by force while it is operating high temperature washing drying spinning e Water flowing out of the washing machine may result in burns or cause the floor to be Slippery This may result in injury English 9 WD80J6410AX EN indd 9 ar 2015 2 7 11 39 01 zu zu Safety information e Opening the door by force may result in damage to the product or injury Do not insert your hand under the washing machine while an operation is in progress e This may result in injury Do not touch the power plug with wet hands e This may result in electric shock Cc oO gt ge ie ye gt w eb eu ge va
44. s being harmful to humans this may result in electric shock fire or problems with the product Do not place objects that generate electromagnetic fields near the washing machine e This may result in injury due to a malfunction Water drained during a high temperature wash or drying cycle is hot Do not touch the water e This may result in burns or injury Do not wash spin or dry water proof seats mats or clothing unless your appliance has a special cycle for washing these items Woollen bedding rain covers fishing vests ski pants sleeping bags diaper covers sweat suits and bicycle motor cycle and car covers etc e Do not wash thick or hard mats even if the washing machine mark is on the care label This may result in injury or damage to the washing machine walls floor or clothing due to abnormal vibrations e Do not wash throw rugs or doormats with rubber backing The rubber backing may come off and stick to inside the drum and this may result in malfunction such as a drainage error Do not operate the washing machine when the detergent drawer is removed e This may result in electric shock or injury due to a water leak Do not touch the insides of the drum during or just after drying as it is hot e This may result in burns Do not insert your hand into the detergent drawer e This may result in injury as your hand may be caught by the detergent input device e The liquid detergent guide applica
45. s involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision 4 English WD80J6410AX EN indd 4 ar 2015 2 7 11 39 01 If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard This appliance should be positioned so that the power plug the water supply taps and the drain pipes are accessible a D a D 2 lt 5 O N D a 5 For appliances with ventilation openings in the base that a carpet must not obstruct the openings The new hose sets supplied with the appliance are to be used and that old hose sets should not be reused N CAUTION In order to avoid a hazard due to inadvertent resetting of the thermal cut out this appliance must not be supplied through an external switching device such as a timer or connected to a circuit that is regularly switched on and off by the utility The tumble dryer is not to be used if industrial chemicals have been used for cleaning The lint trap has to be cleaned frequently if applicable Lint must not to be allowed to accumulate around the tumble dryer not applicable for appliances intended to be vented to the exterior of the building Adequate ventilation has to be provided to avoid the back flow of gases into the room from appliances burning other fuels including open fires Do not dry unwash
46. the grounding Do not modify the provided plug If it does not fit the outlet call a qualified electrician to install a proper outlet WARNING e Do NOT use an extension cord e Use only the power cord that comes with the washing machine e Do NOT connect the ground wire to plastic plumbing gas lines or hot water pipes e Improperly connected grounding conductors may cause electric shock Water supply A proper water pressure for this washing machine is between 50 kPa and 800 kPa Water pressure less than 50 kPa may cause the water valve not to close completely Or it may take longer to fill the drum causing the washing machine to turn off Water taps must be within 120 cm from the rear of the washing machine so that the provided inlet hoses reach the washing machine To reduce the risk of leaks e Make sure water taps are easily accessible e Turn off the taps when the washing machine is not in use e Check for any leaks at the water inlet hose fittings on a regular basis CAUTION Before using the washing machine for the first time check all connections at the water valve and taps for any leaks Drain Samsung recommends a standpipe in height of 60 90 cm The drain hose must be connected through the hose clip to the standpipe and the standpipe must fully cover the drain hose English 17 2015 2 7 11 39 02 un a 2 D et oO Oo ig Wn e Insta
47. this time the Power button is inoperative e Make sure the cold water supply hose is firmly connected to 4C2 the cold water tap If it is connected to the hot water tap the laundry may be deformed with some cycles Water is not draining e Make sure the drain hose is not frozen or clogged e Make sure the drain hose is positioned correctly depending on the connection type 5C e Clean the debris filter as it may be clogged e Make sure the drain hose is straightened all the way to the drain system e If the information code remains contact a customer service centre Operating the washer with the door open DC e Make sure the door is properly closed e Make sure laundry is not caught in the door 5 je S oO gP 1 je Oo ep Ce Water is overflowed oc e Restart after spinning e Ifthe information code remains on the display contact a local Samsung service centre English 53 WD80J6410AX EN indd 53 ar 2015 2 7 11 39 11 zu zu Troubleshooting Problem Action Check the drain hose e Make sure the end of the drain hose is placed on the floor LC e Make sure the drain hose is not clogged e Ifthe information code remains contact a customer service centre NOTE LC1 When the washer displays the LC LC1 code the washer do draining for 3 minutes During this time the Power button is inoperative Spinning does not work e Make sure
48. ual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance Please store the manual in a safe location close to the appliance for future reference Use this appliance only for its intended purpose as described in this instruction manual Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur It is your responsibility to use common sense caution and care when installing maintaining and operating your washing machine Because the following operating instructions cover various models the characteristics of your washing machine may differ slightly from those described in this manual and not all warning signs may be applicable If you have any questions or concerns contact your nearest service centre or find help and information online at www samsung com Important safety symbols What the icons and signs in this user manual mean J N WARNING Hazards or unsafe practices that may result in severe personal injury death and or property damage N CAUTION Hazards or unsafe practices that may result in personal injury and or property damage NOTE Indicates that a risk of personal injury or material damage exists English 3 WD80J6410AX EN indd 3 a 2015 2 7 11 39 01 zu zu Safety information These warning signs are here to prevent injury to yourself and others Please follo
49. ure the washing machine is running with sufficient water pressure e Make sure the detergent is added to the centre of the detergent drawer e Make sure the rinse cap is inserted properly e f using granular detergent make sure the detergent selector is in the upper position e Remove the rinse cap and clean the detergent drawer After a cycle detergent remains in the detergent drawer D O f WY u Fa 5 O pas 48 English WD80J6410AX EN indd 48 ar 2015 2 7 11 39 11 Problem Action e Make sure the washing machine is installed on a level solid floor that is not slippery If the floor is not level use the levelling feet to adjust the height of the washing machine e Make sure the shipping bolts are removed e Make sure the washing machine is not contacting any other object e Make sure the laundry load is balanced e The motor can cause noise during normal operation e Overalls or metal decorated clothes can cause noise while being washed This is normal e Metal objects such as coins can cause noise After washing remove these objects from the drum or filter case Excessive vibrations or makes noise e Make sure the drain hose is straightened all the way to the drain system If you encounter a drain restriction call for Service e Make sure the debris filter is not clogged e Close the door and press or tap Start Pause For your safety the washing machine
50. utton Use case You want to finish a two hour course 3 hours later from now For this you add the Delay End option to the current course with the 3 hour setting and press the Start Pause button at 2 00 p m Then what happens The washing machine starts operating at 3 00 p m and ends at 5 00 p m Provided below is the time line for this example 2 00 pm 3 00 pm 5 00 pm Set the Delay End to 3 hours Start End fe O D R g O un English 37 WD80J6410AX EN indd 37 ar 2015 2 7 11 39 09 Operations Settings Child Lock Sound On Off To prevent accidents involving children the You can turn on or off the key tone beep Child Lock function locks all buttons or alarm Your setting will remain effective However Child Lock does not activate until after you restart the machine you press Start Pause e To mute the sound hold down the Rinse In the holding state you can open the and Spin buttons simultaneously for 3 door or change settings by pressing seconds The icon indicator turns on corresponding buttons However once e To unmute the sound hold down again you press Start Pause to start the washing for 3 seconds machine the Child Lock will be reactivated e Child Lock locks all buttons except for Power e To activate or deactivate Child Lock hold down Temp and Rinse simultaneously for 3 seconds NOTE To add detergent put more laundry in the drum or change the cycle settings whilst in the Child Loc
51. w them explicitly After reading this manual store it in a safe place for future reference Read all instructions before Using the appliance As with any equipment that uses electricity and moving parts potential hazards exist To safely operate this appliance familiarize yourself with its operation and exercise care when using it Cc oO ie ru gt pe fed ye ice va Important safety precautions N WARNING To reduce the risk of fire electric shock or injury to persons when Using your appliance follow basic precautions including the following Do not let children or pets play in or on your washing machine The washing machine door does not open easily from the inside and children may be seriously injured if trapped inside This appliance is not to be used by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their Safety Children should be supervised to ensure that they do not play with the appliance For use in Europe This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance ina Safe way and understand the hazard
52. your clothes directly or dry the washed clothes according to the following procedures Operations 34 English WD80J6410AX EN indd 34 COTTON SYNTHETICS WOOL BABY CARE OUTDOOR CARE RINSE SPIN ECO DRUM CLEAN 1 Press Power button on the washing machine 2 Use the Cycle Selector to select the appropriate drying cycle 3 Press Dry Level button to select the appropriate drying mode 4 Press Start Pause button to start dry Hold 3 sec Delay End Options Rinse Spin Dry Leve Bubble Soak 2015 2 7 11 39 07 Course overview Standard courses WD80J6410AX EN indd 35 Course Description amp Max load kg For cottons bed linens table linens underwear towels or shirts ur The washing time and the number of rinse cycles are Mar automatically adjusted according to the load SYNTHETICS For blouses or shirts that are made of polyester 35 diolen trevira polyamide perlon nylon or the like Specific for machine washable wool for loads less than 2 0 kg WOOL The wool course features gentle cradling and soaking 2 to protect the wool fibres from shrinkage distortion A neutral detergent is recommended i ighi i BABY CARE Featuring a high temperature wash and extra rinses to 4 5 ensure that no powder detergent remains F For outdoor clothes skiwear and sportswear that are o OUTDOOR
Download Pdf Manuals
Related Search