SECO-LARM SK-910RAQ
Contents
1. mode The LED will turn steady ON 1 sec to show the code Is already in memory 2 Each channel can learn the codes of a maximum of 15 transmitter buttons If you attempt to learn a sixteenth button the earliest code learned will be deleted and replaced by the new code first in first out 3 To clear all codes To clear all codes in the channel s memory press the appropriate mode switch 1 or 2 for three seconds When the LED starts flashing press that switch again for three seconds The LED flashes twice to indicate that all codes associated with that channel are now deleted Programming Output Modes see table 1 4 second momentary Press the transmitter button once The output turns on for 4 seconds and then turns off This is the DEFAULT mode l second momentary Press the transmitter button once The output turns on for 1 second and then turns off Toggle Press the transmitter button once and the output turns on Press a compatible transmitter button again and the output turns off Validity The relay turns on for as long as the transmitter button is pressed Mode Switch Operation one per channel Learn mode Press and hold the switch for three seconds The appropriate LED will flash quickly to show that it is ready to learn a transmitter code Clear memory Press three seconds then when the appropriate LED starts flashing press again for three seconds to delete all previously learned codes The LED will flash twice2. to confirm codes deleted Memory Display Press and immediately release the mode switch to show number of codes stored The appropriate LED will flash a number of times to correspond to the number of codes stored LED Indication one per channel Steady on Senses signal from a transmitter button whose code was already learned Fast flash In the code learning mode One flash A transmitter button code was learned Two flashes All previously learned transmitter button codes were deleted Page 2 ENFORCER RF RECEIVERS SK 910RAQ SK 910RAVQ RAV2Q Mode switch 2 SK 910RAV2Q only Loop 3 Mode switch 1 Ext range antenna connector Loop 2 Loop 1 Loop 4 k Channel 1 Status LED Channel 2 a Status LED SK 910RAV2Q only w VAC VDC No polarity COM Ch 1 transistor ground NO Ch 2 transistor ground NC SK 910RAV2Q only Table 1 To program outputs morener momenty OE AUD NOTE For the SK 910RAV2Q open case and find the jump MOMENTARY MOMENTARY 2 channel model the mode of ers marked LP1 LP2 LP3 el Be e both outputs is the same In and LP4 Cut these jumpers JE SEA other words you cannot have if needed as follows CUT LP3TO USE EXTERNALANTENNA for SK S1ORAQony 4 Second momentary output for baal CUT LPA FOR 16 24VACIDC POWER INPUT for SK 910RAQony Channel 1 and a validity output A for channel 2 Typical Applications Positive or negative output Mode swit
3. ENFORCER RF RECEIVERS Specifications ______ SK 910RAQ SK 910RAVQ_ SK 9 10RAV2Q Up to 500 range Operating Voltage 11 24 V AC DC 16 24 VAC DC must cut LP4 3 13 8 VDC Memory Capacity 15 transmitter button codes per channel 5mA standby 50mA LED flashing 5mA standby 15mA LED flashing 12VDC 12VDC Output mode Programmable 4 sec momentary default 1 sec momentary toggle ON OFF or validity Output type 3A Form C relay NO NC C Transistor GND x 1 5A 12VDC Transistor GND x 2 3A 12VDC BY KT x 80x65x19 mm 315MHz Other frequencies available Please contact SECO LARM Compatible with all SECO LARM transmitters Compatible Transmitters Fixed Code 68 billion codes CODEBUMP code hopping 18 quintillion 1 8 x 10 codes Pendant Remotes SSIES Bank SK 919TD2A UP 919TD2A UP ase JEU SK 919TP3J N o Fed Pre coded coded SK 917T3 91773 Hopping SCO 919TP4J N Fixed Pre coded coded SK 917TP4J N a Code Hopping coded Hand Held Remotes Model Number ell or wasinunier ot ote come Batt CODEBUMP With SECO LARM s CODEBUMP so called code grabbers and scan ners are rendered obsolete because the RF code changes every time the transmitter button is pressed In addition with over 18 quintillion 1 8 x 10 codes the chances of ever repeating a code are virtually non existent SECO LARM s CODEBUMP transmitters and receivers a
4. ch 1 cH Ci 1 002 LED 12VDC receiver power driving a 12VDC appliance Positive or Negative Power Output Choose NO or NC Positive or Negative Electromagnetic lock Power Source oe ae Power for SK 910RAQ GND Power for SK 910RAQ SK 910RA 40 12VDC SK 910RA 4Q For SK 917 0RAVQ SK 910RAV 4Q and SK 910RAV2Q SK 910RAV2 40 CH 2 Output 12VDC receiver power input 24VAC output driving a motor 2AVAC 1 Output voto 24VAC 2 4VAC 1 Input enD Fey ee GND 12VDC 3 13 8VDC For SK 910RAVQ SK 910RAV 4Q For SK 910RAV2Q SK 910RAV2 4Q Extended Range Antenna for SK 910RAQ only The optional SK 91ERSD extends the RF receiver range to up to 1 200 open air with existing remotes The antenna comes with a 9 cable which easily plugs into the 3 pin antenna port located on the RF receiver motherboard see the illustration above IMPORTANT If an extended range antenna is used with the SK 91ERSD SK 910RAQ the receiver PC board loop marked LP3 must be cut Page 3
5. odels work on 11 24VAC DC except for the low voltage versions Tested To Comply war With FCC Standards Note Products with model numbers that end with Q or that have a round green Q sticker are RoHS compliant ENFORCER RF RECEIVERS pe ee a Learning a New Button Code channel 1 1 Press the mode switch which is located at the top of the receiver case for three seconds The green LED will start to flash quickly 2 While the green LED is flashing quickly press a button on a compatible transmitter The green LED will flash once and then turn off to show that button was learned 3 Repeat steps 1 and 2 to learn more buttons into channel 1 NOTE The green LED will flash a maximum of 15 seconds If no transmitter button is pressed during this time the receiver will exit the code learning mode and the green LED will turn off Learning a New Button Code channel 2 SK 910RAV2Q only The procedure is the same as for channel 1 except mode switch 2 black switch initiates the code learning process and the red LED shows status For two channel receivers red color push button represent mode switch 1 and black color push button represent mode switch 2 nee Regarding Code Learning The receiver will only learn the code of a particular button once Once a button s code is learned if you try to code learn that button again whether it is for the same channel or not the receiver will remain in the code learning
6. pping and fixed code transmitters see page 4 of this manual for a list of compatible transmitters They can be used for a variety of applications such as allowing the same transmitter to arm disarm a vehicle alarm and open close a garage door opener The receivers come in one or two channel versions Each channel can learn the codes of up to 15 different transmitter buttons on a first in first out basis Installation Notes 1 Mount out of sight in a location where it is not surrounded by metal and where it is not exposed to the weather or moisture Metal will block the RF signal resulting in a reduced range 2 For best range pull the antenna wire as straight and high as possible If the receiver receives interference from local RF activity eg airport or military base the antenna wire can be folded DO NOT CUT THE ANTENNA WIRE Models Available SK 910RAQ 1 channel mini receiver 3A Form C relay 315MHz SK 910RAV Q 1 channel mini receiver 5A transistor ground output 315MHz SK 910RAV72Q 2 channel mini receiver 3A transistor ground outputs 315MHz SK 910RA 4Q 1 channel mini receiver 3A Form C relay 433 92MHz SK 910RAV 4Q 1 channel mini receiver 5A transistor ground output 433 92MHz SK 910RAV2 4Q__ 2 channel mini receiver 3A transistor ground outputs 433 92MHz More RF receivers are available 1 to 4 channels Contact SECO LARM for details SLI SECO LARM All m
7. re perfect for controlling SK 919TP4H N garage and gate openers Accessories car and home alarms SK 9HBC plus much more WARRANTY These ENFORCER RF receivers are warranted against defects in material and workmanship while used in normal Service for a period of one 1 year from the date of sale to the original customer Our obligation is limited to the repair or replacement of any defective part if the unit is returned transportation pre paid to SECO LARM Bo ie E i e o e ee E Belt clip holster for hand held remotes Copyright 2013 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM The SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without further notice FILE D DTP Manual Mi SK 910RAxxQ_051013 indd SECO LARM U S A Inc wi PITSW1 Order Part 762 107 3 16842 Millikan Avenue Irvine CA 92606 Website www seco larm com Tel 800 662 0800 949 261 2999 Fax 949 261 7326 E mail sales seco larm com Page 4 Installation Manual ENFORCER SK 910RAQ SERIES Miniature RF Receivers Up to 500 ft range e Operate on 11 24VAC DC e Code learning SK 9 1ORAQ Shown e FCC compliant e Fixed code or CODEBUMP code hopping Introduction These mini RF receivers are compatible with both code ho
Download Pdf Manuals
Related Search