DJI Phantom 1
Contents
1. Advanced Manual V 1 4 2013 03 22 Revision 2013 DJI Innovations All Rights Reserved 1 Index 1 SOFTWARE AND DRIVER INSTALLATION 2 CONFIGURATION AND FIRMWARE amp SOFTWARE UPGRADE LINKING THE TRANSMITTER AND RECEIVER cccccccscceccscceccscceccsccesesccesesseeees 4 CHANGING THE CONTROL MODE OF THE 5 TRANSMITTER CALIBRATION siiccccccdnssavccssdvcndssestaneiwidvaetenssasditsaesvetendesdescekcadatessssuvens MOUNT CAMERA AND CAMERA FRAME scccsscceccscccccsccecesccesesccesesscesessoeees A7 INTELLIGENT ORIENTATION CONTROL IOC FLIGHT WITH GPS amp COMPASS MODULE 2013 DJI Innovations All Rights Reserved 2 7 Software and Driver Installation A3 Linking the Transmitter and Receiver Make sure to use the NAZA M assistant software of 2 0 version or above 2 0 to carry out firmware upgrade The linking of the transmitter to the receiver of the PHANTOM was carried out before they left the factory If and parameter configuration DO NOT use the NAZA M assistant software bellow 2 0 version necessary you can link the transmitter to the receiver as follows for example you replace the transmitter The Please download the driver DJI Driver Installer and NAZA M assistant software from the PHANTOM default receiver type is PPM page o2. home point before you switch on IOC mode during the flight Continuously spinning the aircraft in flight will cause a yaw error In this case you can stop or slow down the spinning so as to have better flight performance 2013 DJI Innovations All Rights Reserved 10 A8 Maintenance 1 Remove the Housing Remove all the nuts and propellers by using the assistant wrench Remove the screws marked in the figure below using a Phillips Screwdriver and a Hexagon Screwdriver and then remove the housing Note Please take good care of the removed parts for example screws Make sure to keep them safe and away from children DO NOT use any thread locker since the thread locker may corrode the shell of Phantom may cause fractures of gt a if Faran ree f 6 2013 Innovations All Rights Reserved 2 Extension Power There is an extension power cable in the Phantom for DIY use The voltage from the Extension Power Cable is the same voltage as the power battery The red cable is for positive and the grey cable is for negative Make sure to keep the red cable and the grey cable separated to avoid short circuit Extension Power Cable 2013 DJI Innovations All Rights Reserved 12
3. M assistant software before using Definition of Forward Direction Quad rotor will fly along this direction when you push the elevator stick Graphic Description D Nose direction gt Forward direction Home point eeee Over 10m from Home point Before You Start Usually the forward direction of a flying aircraft is the same as the nose direction By using wherever the nose points the forward direction has nothing to do with nose direction course lock flying the forward direction is the same as a recorded nose direction See the following figures The red and blue arrows on the transmitter is corresponding to pitch and roll operations Eat Usually In course lock In home lock flying the forward direction is the same as the direction from home point to aircraft See the following figures The red and blue arrows on the transmitter is corresponding to pitch and roll operations oe In home lock _ Usually SHome point Home point Method of Forward Direction amp Home Point Recording If you use the IOC function please keep the Forward Direction of Course Lock Flying and the home point of Home Lock Flying in mind at any time There are two ways to record the forward direction and the home point Manually and Automatically You may choose any one record method Course Lock Flight Home Lock Flight Before takeoff the current of the 30 seconds after you power on the quad rotor will
4. ator sound of from the transmitter Then move all of the sticks throughout their complete range several times After this put the Throttle stick to the bottom position and toggle the switch S2 to the HL position you should hear an indicator sound of Di from the transmitter in this case the transmitter has been calibrated successfully 2013 DJI Innovations All Rights Reserved 7 Mount Camera Camera Frame Please mount the Camera and Camera Frame if necessary 1 Mount the Camera to the Camera Frame 2 Mount the Camera and Camera Frame to the aircraft Make sure to use the dedicated cross screws of the type M3 0 6 since an over long screw will puncture the battery by passing through the battery compartment and could lead to explosion or fire pS 22 T LOA _ 2 A ae ke l i fo M aes 4 E a pounne ay 2 ees 5 re ey of gh a J l N J uh G TN ie VSS 0 H 2 poene J C aoe C ee J J ee a J f 1 4 H 2013 DJI Innovations All Rights Reserved 8 7 Intelligent Orientation Control IOC Flight with GPS amp compass module Make sure to open the IOC function in the NAZA
5. be saved as home point when you Automatically quad rotor push the throttle stick for the first time after 6 or more GPS satellites have been found Switch the 52 between OFF and When 6 or more GPS satellites are found you can CL position quickly to 5 times to toggle the 52 switch between CL and HL position record current nose direction as Manually quickly 3 to 5 times to record the current position new forward direction after you of the quad rotor as the new home point CL gt power on the quad rotor for 30s HL gt CL is one time OFF gt CL gt OFF is one time 2013 Innovations All Rights Reserved 9 IOC Flying Test Realize an IOC flight by the following procedures During the STEP1 same flight Record STEP2 ON STEP3 OFF STEP4 ON again Course Set switch S1 to GPS or Switch Record forward Set switch S2 Toggle switch S2 from ATTI position S2 to CL Seiting direction to OFF position OFF to CL position position Home Lock L L o i Set switch 51 to GPS Switch Record i Set switch S2 Toggle switch S2 from position and S2 to HL i Setting home point to OFF position OFF to HL position i i position i LED will blink quickly if recording is successful LED will blink between Oand slowly to indicate the IOC mode only when MC is ready to fly in course lock or home lock modes Ho
6. er Make sure the computer is connected to the Internet for the first time you use Switch on the transmitter first then power on the aircraft Connect the aircraft to the PC with the USB cable DO NOT break the connection until configuration or upgrade is finished Please refer to the Assembly amp Configuration gt Step3 section of NAZA M Quick Start Guide to get the detail of assistant software usage Receiver Module Refer to the Appendix gt Firmware amp Assistant Software Upgrade section of NAZA M Quick Start Guide to get the detail of assistant software usage If Manual Mode is required please select Manual from the drop down list of Basic gt RC gt Control LED Mode Switch in the assistant software Refer to the Flying Test gt Step 1 Control Mode Knowledge Link Button section of NAZA M Quick Start Guide to get the detail about the Manual Mode 2013 DJI Innovations All Rights Reserved 3 2013 DJI Innovations All Rights Reserved 4 4 Changing the Control Mode of the Transmitter You can change the operation mode of the transmitter according to the following procedures if necessary The operation mode of Mode1 and Mode2 are shown as below Make sure to carry out the A5 Transmitter Calibration if the Control Mode of the Transmitter is changed a Mode1 Throttle it cannot hold the central position when released Roll it can return to the central position when
7. eserved 5 The following figure shows the successful change of transmitter mode to 1 Mode1 2013 DJI Innovations All Rights Reserved 6 5 Transmitter Calibration If the control mode of the transmitter is changed or calibration has not been carried out for a long time transmitter calibration is necessary IOC Switch Control Mode Switch OFFQ GPS ATTI HL ATTI Joystick Joystick Pitch Mode1 Throttle 1 Throttle Mode2 Pitch Mode2 eo e Roll aw o 4 v Power Switc CL Course Lock HL Home Lock Set the switch S2 at the OFF position and the switch S1 at the GPS position Push the Throttle stick to the top position and push the Pitch stick to the top position Keep the Pitch stick at the top position manually since it can return to the central position when released Turn on the Power Switch of the transmitter you should hear the indicator sound of Di Di Di from the transmitter repeatedly Toggle the switch S2 to the CL position you should hear an indicator sound of Di from the transmitter in this case the transmitter has entered the calibration mode During this period the Throttle stick and the Pitch stick must be kept at the top position all the time Release the Pitch stick and pull the Throttle stick to the central position Toggle the switch S1 to the ATTI position you should hear an indic
8. f DJI website http www dji innovations com products phantom downloads Connect the PHANTOM and the PC via the USB cable power on the PHANTOM system DO NOT use the PHANTOM transmitter receiver with the third party remote control equipment Run the DJI Driver Installer and follow the instructions strictly to finish installation Run the assistant software installer and follow the instructions strictly to finish installation Please remove the housing by referring to the section of 8 Maintenance gt Remove the Housing Locate the receiver module according to the following figure After powering on the aircraft and the transmitter if the LED indicator of the receiver on the control board is lit solid red this means the receiver currently has no connection with any transmitter Press down the link button for more than two seconds until the LED indicator blinks then release the button Push the throttle stick to the lowest position and turn on the transmitter Then if the LED indicator of the receiver turns off the link between the transmitter and the receiver has succeeded Linking operation can be done only when the LED indicator of the transmitter changes to blinking red Note If the transmitter can t enter the linking mode please check that the throttle stick lies in the lowest position You can use your R C system normally only after the linking is done successfully Power on your comput
9. me lock flying requires that 6 or more GPS satellites are found and the aircraft is further than 10m away from the home point Before you do the home lock flight you have to fly the aircraft out of the 10m range around home point and then flip the switch S2 to HL position to fly in home lock when all the requirements are met If you have already toggled the switch S2 to HL position when the aircraft is still in 10m range around home point and this is the first time you are going to fly in home lock during the current flight then if all the requirements are met MC will change into home lock automatically when the aircraft flies out of the 10m range around home point When flying in Home Lock mode if any of the following situations happen then the system will quit Home Lock flying and automatically enter Course Lock flying The aircraft will fly in Course Lock using the earlier forward direction 1 The aircraft fly s within 10m range of the home point 2 You toggle the control mode switch to the Mode The GPS signal becomes bad The GPS signal LED is blinking Red twice or three times When the aircraft is flying in home lock mode far away from you and the home point please do not toggle the IOC switch many times quickly so as to avoid the change of home point without you intentionally knowing We suggest that you should know clearly which flight lock method you are going to fly and you know the locked forward direction or
10. released Pitch it can return to the central position when released Yaw it can return to the central position when released Model2 Throttle it cannot hold the central position when released Roll it can return to the central position when released Pitch it can return to the central position when released Yaw it can return to the central position when released Remove the right Throttle Ratchet plate and the Ratchet Nut Assemble the Ratchet Nut to the Nut Hole Location and fix the Throttle Ratchet onto the Ratchet Nut and the Screw Hole Location Adjust the screw height of the Throttle Support to change the tension so as to give you the required operating feel Remove the left Centering Unit and the Centering Spring Assemble them to the corresponding position of the Right part Close to the middle location of the transmitter Then adjust the height of the Adjusting Screw so as to give you the required operating feel Note Be careful not to excessively tension the spring when moving and fixing to avoid damage Exchange the connectors of Channel 2 AIN2 and Channel AIN3 Note Take care about the connector direction Name Screw Hole Location Centering Unit Adjusting Screw Ratchet Nut Throttle Ratchet 3rd Channel WH MERANA 2nd Channel 4 Centering Spring 2 3 4 5 6 7 8 9 Nut Hole Loc tion 6 2013 DJI Innovations All Rights R
Download Pdf Manuals
Related Search