CDA WC140
Contents
1. Rinse Aid Warning Light When the rinse aid begins to run out the Rinse Aid Warning light will illuminate to advise that the rinse aid needs refilling End of Programme Light When the programme is complete the dishwasher will emit five beeps and the End of Programme light will illuminate Press the Power button Press the Programme Selection button until the required Programme light is illuminated If required press the Delay Timer button Once the power is switched on the End of Programme Indicator light will switch on Once a programme is selected the End of Programme Indicator light will switch off and the Programme Indicator light will switch on When you close the dishwasher door the programme will start automatically Please note The dishwasher stores the most recently used programme in its memory To change the programme simply press the Programme Selection button If possible do not open the dishwasher door once the programme has Started At the end of the programme the dishwasher will beep five times and the End of Programme Indicator light will switch on It is possible to change the programme if necessary once the programme has started First open the door slightly to reduce the risk of water spillage Press the Programme Selection button until the required Programme Indicator light is illuminated Then close the door The dishwashe2. Alternatively there are specialist dishwasher cleaners available that can be used 21 22 The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance Error code Epa Intensive Quick description Prewash Inadequate water supply Continual fill error ly ly ZN ZN The waste water in the machine cannot be discharged ly ZN Ne ZIN Heater error Alz ZIN sly o ZIN Alarm is active against water overflow Faulty electronic card SY Aly ly ly e e e e ZN ZN ZN ZN a 7 Overheating error temperature in the machine is too high ly e 5 ly lt p ZN ZN ly o ZN Faulty heater sensor AJZ aN Advice Make sure the water inlet tap is fully open Close the water tap separate the water inlet hose from the tap and clean the filter Restart your machine and contact CDA service if the error continues Close the tap and contact CDA service Drain hose is blocked The filters of your machine might be blocked Restart the dishwasher and cancel the programme If the error continues contact CDA service Contact CDA service Turn off the dishwasher and disconnect from the water supply Contact CDA service Contact CDA service Contact CDA service Contact CDA service Troubleshooting Check the plug fuse and circuit breakers of the mains sup
3. Open the testing strip 2 Run water through the tap for one minute 3 Hold the testing strip in water for one second 4 Shake the testing strip after taking it out of the water 5 Wait for one minute 6 Check the number of marks on the strip to see the level of water hardness If the hardness of the water you use is above 63dE or if you are using well water you are recommended to use filter and water refinement devices Please note The level of water hardness is preset to level 3 1 Press and hold down the Programme Selection button 2 Press the Power Button to switch on the dishwasher 3 Keep the Programme Selection button pressed until the five Programme Indicator lights and the End of Programme Indicator light flash 4 lo adjust the level press the Programme Selection button until the required level is selected The Programme lights will illuminate as in the table of water hardness settings below 5 To store the selected water hardness level press the Power button Water aritish Hardness Level Indicator pq Po Pa PS aa SN 1 0 6 P1 PS leds are on o OIO a 714 P2 P5 leds are on O OIO 3 15 21 P3 P5 leds are on O 6 4 22 26 P PS lode aro on O 0e aa ieena 0 0 o 6 4063 P2 P4 PS ledsareon O OoO Rinse Aid To fill the rinse aid compartment 1 Open the rinse aid compartment by turning and r
4. and prevent any water spilling out Remember that the water in the dishwasher can be very hot when the programme is running When the dishwasher is not in use we reccomend that you turn off the water supply at the supply tap and disconnect the main supply If you are leaving the dishwasher for an extended period you should leave the door slightly open to prevent the formation of unpleasant smells This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance Shall not be made by children without supervision To reduce energy and water consumption remove all dirt residues from the dishes prior to loading the dishwasher Only run the dishwasher when fully loaded Place hollow items bowls glasses and pans face down in the basket Set the water softener level as required by the water hardness in the area Add 2kg of salt into the salt compartment and then fill with water to the top of the salt compartment Remove allthe packaging materials from the interior of the dishwasher Fill the rinse aid compartment Run a hot programme without any dishes in the dishwasher WC140 Programme selection Power button
5. 1 Then close the detergent compartment lid until the latch locks Please note You should only use detergents designed specifically for use in dishwashers If using dishwasher tablets always use the detergent compartment do not put them in the main body of the dishwasher or in the cutlery basket The solubility of dishwasher tablets can vary depending on the temperature and duration of the programme As a result it is recommended that powder detergents should be used in the shorter programmes to allow better performance CDA recommends the use of separate detergent rinse aid and dishwasher salt rather than combination tablets as separates achieve better wash performance If you do use combination detergents add salt and rinse aid to the dishwasher and then adjust the water hardness setting and rinse aid setting to the minimum When you then use separate detergents again you should fill the salt and rinse aid compartments adjust the water hardness setting to the maximum and run an empty wash then adjust the water hardness setting and the rinse aid setting to the appropriate level To ensure the best efficiency the dishwasher needs soft water Hard water means that lime residues remain on the dishes and the interior of the dishwasher affecting performance The softener system is designed to remove the ions that make the water hard to provide the best quality wash performance This is achieved by using dishwash
6. 2 button 1 Delay timer button 3 Indicator lights Power Button To switch the power to the dishwasher on or off press the Power button 1 When you switch on the dishwasher the End of Programme light will illuminate Programme Selection Button To select a programme press the Programme Selection button 2 The dishwasher will store in its memory the last programme used To change the programme press the Programme Selection button again until the light next to the required programme is illuminated Delay Timer Button and Delay Timer Indicator Lights The dishwasher is equipped with a variable delay timer of three six or nine hours duration To set the delay timer press the Delay Timer button 3 This will switch on the delay timer for three hours and the 3h light will illuminate To change the duration press the Delay Timer button again until the light next to the required time 6h or 9h is illuminated To cancel the timer press the Delay Timer button again until none of the Delay Timer indicator lights are illuminated As the delay timer counts down the Delay Timer Indicator lights will illuminate in turn so at six hours delay the 6h light will illuminate and at three hours delay the 3h light will illuminate Salt Warning Light When the dishwasher salt begins to run out the Salt Warning light will illuminate to advise that the salt needs refilling
7. e must be earthed The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug To change a fuse in this type of plug follow the Steps below 1 Remove the fuse cover and fuse 2 Fit replacement 13A fuse ASTA approved to BS 1362 type into the fuse Cover 3 Replace fuse cover Important Do not use the appliance without the fuse cover in position How to connect an alternative plug If the fitted plug is not suitable for your socket outlet then it should be cut off and disposed of safely to avoid the risk of electric shock A Suitable alternative plug of at least 13Amp rating to BS 1363 should be used As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with the letter E or by the Earth symbol or coloured GREEN and YELLOW The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK or BLUE The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED or BROWN If in doubt regarding the electrical connection of this appliance consult a qualified electrician Do not shorten the supply cable the appliance may require removing for servicing N B Ensure that the pl
8. emoving the cap as shown in Fig 4 2 Fill the rinse aid compartment until the rinse aid indicator goes dark as shown in Fig 5 where a indicates the compartment is empty and b indicates the compartment is full 3 Replace the cap ensuring the markers on the cap line up with the compartment prior to screwing the cap back in place Rinse Aid Adjustment The level of rinse aid use is preset to 4 You can adjust the level of rinse aid use by adjusting as shown in Fig 6 If water stains form on the dishes after a wash the level should be increased If blue stains which can be wiped away are left on the dishes after a wash the level should be decreased Please note Rinse aid ensures better quality wash results and increased drying performance Always refill the rinse aid when the rinse aid indicator light on the control panel is illuminated Dishwasher Baskets To adjust the height of the upper basket 1 Open the basket retaining clips as shown in Fig 7 by turning them to the side 2 Remove the upper basket and relocate the alternate set of wheels on the runner as shown in Fig 8 pushing the basket back into place 3 Close the basket retaining clips The images below are designed as guidance as to best practice for loading the dishwasher Upper basket Lower basket Standard Loading and Test Data Capacity e Upper and lower baskets 12 place settings The upper bask
9. er Salt To add dishwasher salt 1 Remove the lower dishwasher basket and then unscrew the salt compartment cap as shown in Fig 2 2 Fill the compartment with dishwasher salt do not use table salt carefully to prevent unnecessary spillage Before first use you should fill the compartment with 2kg of dishwasher salt and then fill up the salt compartment with water up to the brim of the compartment as shown in Fig 3 3 Replace the cap and the lower basket When the Salt Warning light on the control panel illuminates you Should refill the salt compartment with salt only do not add water to the salt compartment after the first use You should run a programme immediately after adding dishwasher salt to prevent any damage to the dishwasher systems The efficiency of your dishwasher depends on the softness of the tap water To ensure best efficiency the dishwasher is equipped with a system that reduces the hardness in the mains water supply The efficiency will increase when the system is correctly set To find out the water hardness level of your water supply you can use the test strip supplied or alternatively contact your local water board ii s pm wer COE No Lime 1 a Pe tent a l puis ws COTTIER Very low lime content F i i Tii s P i T _ os OOE Low lime content 2 J l E i H l T E E Medium lime content S i LIE E _ E E Lime content i vee 6 M E By High Lime content 1
10. et should be adjusted to high position e Cups should be placed onto the dish rack pins Detergent Rinse aid gt 5 25cm in accordance with EN50242 DIN 44990 IEC 436 international norms Rinse aid dosage adjustment 4 Programme test e Economic 50 C in accordance with EN50242 international norms CANDE ah F eee ESSER SRE Intensive 70 C P1 Programme names and temperatures Super 65 C P2 Type of food waste Soups Sauces pasta eggs pilaf potato and oven dishes fried foods pasta eggs pilaf potato and oven dishes fried foods Soups Sauces Eco 50 C P3 Coffee milk tea cold meats vegetables not kept for long Quick 40 C P4 Coffee milk tea cold meats vegetables not kept for long Prewash No Heat P5 Pre wash to rinse and loosen residue awaiting full load then select a programme Detergent amount A 25cm 15cm B 5cm Electricity consumption kWh Water consumption litres aw fw ow o E Warning Short programmes do not include a drying stage The values and times provided opposite have been obtained under laboratory conditions according to relevant standards This information can change depending on the conditions of the dishwashers use and environment network voltage water pressure water input temperature and environment temperature 20 Care and Maintenance Before beginning any care o
11. ply The programme will not start The water tap is turned off The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked Water remains inside the dishwasher at the end ofa The water drain hose is blocked or kinked programme The filters are blocked Power failure The dishwasher stops in the middle of a programme Water inlet failure Programme is on standby Poor loading of dishes hinders wash performance Insufficient detergent added Inappropriate wash programme selected Wash performance is of a low standard Spray arm is blocked Filters clogged or incorrectly fitted Water drain pump is blocked Insufficient detergent added Rinse aid setting is too low White stains on the dishes Insufficient dishwasher salt added Water softener setting is too low Salt compartment cap may not be completely closed A programme without a drying stage was selected The dishes are not completely dry at the end of a Rinse aid setting is too low programme Dishes unloaded too soon allow time for drying Different sets of cutlery should be kept separate Too much salt water softener setting is too high There are rust stains on the dishes Salt compartment cap not completely closed Poor appliance earth check mains electrical supply The door is not opening or closing properly Door tension not correctly adjusted for the decor door 24 Electrical Information Warning This applianc
12. r maintenance you should always disconnect the appliance from the electricity supply and also turn off the water supply Door seals Wipe the dishwasher door seals regularly with a damp cloth to remove any residues Filters You should clean the filters at least once a month 1 Remove the lower basket 2 Turn the microfilter anticlockwise and then lift it out Fig 9 3 Remove the coarse filter from the microfilter Fig 10 4 Remove the base filter from the dishwasher compartment Fig 11 You should clean and rinse the filters thoroughly before replacing all the sections in reverse order to that above The microfilter should lock into place once it is secure Fig 12 Please note Never run a programme without the filters in place Incorrect fitting of the filters may reduce wash performance and potentially damage your appliance Spray arms You should clean the spray arms at least once a month 1 Remove the lower basket 2 Pull the lower spray arm upwards to remove it 3 To remove the upper spray arm first remove the nut on the upper Spray arm by turning it as in Fig 9 You should clean and rinse the spray arms thoroughly before replacing them Ensure that the Upper spray arm nut is securely tightened when refitting the upper Spray arm Dishwasher interior To deal with an accumulation of dirt oil or limescale in the dishwasher run an intensive programme with detergent when the dishwasher is empty
13. r will begin the new programme from the point at which the old programme stopped It is possible to cancel the programme once the programme has Started First open the door slightly to reduce the risk of water spillage Press and hold the Programme Selection button for approximately three seconds until the end of Programme Indicator light flashes and the Programme Indicator light switches off Then close the door The dishwasher will drain for approximately thirty seconds Once this is complete the dishwasher will beep five times and the End of Programme Indicator light will switch on Once the dishwasher beeps five times and the End of Programme Indicator light switches on the dishwasher can be switched off by pressing the Power button Then turn off the water tap and remove the plug from the power socket Please note The dishwasher will automatically continue on the programme it has started if the door is opened and closed or after a power cut Detergent To fill the detergent compartment 1 Push the latch to open the compartment Add the required amount of detergent The main detergent compartment b in Fig 1 has lines to allow for specific amounts of detergent These are marked at either 15cm or 25cm depending on how dirty the dishes are If your dishes are in need of an intensive wash then add 5cm of detergent into the prewasnh section of the compartment a in Fig
14. ug socket is situated in an easily accessible place 25 Installation e Do not install this appliance if it is damaged in any way Installing a damaged appliance may invalidate the warranty The water supply tap should be located in an adjacent cupboard so that it can be accessed after installation Ensure the appliance is level by adjusting the feet as necessary e Only use the water inlet supplied with the appliance If the water pressure is above 10 bar a pressure relief valve should be used After connecting the water supply check to ensure there are no leaks The water outlet can either be connected to a water drain or to a sink outlet spigot This connection should be at a minimum of bOcm and a maximum of 110cm from the floor The drain hose should be no longer than 4m in length to ensure good performance from the dishwasher 26 NOTES 27 Please contact our Customer Care Department for Service on the details below CETP p jie Customer Care Department The ICDIA Group Ltd e Harby Road Langar Nottinghamshire e NG13 9HY T 01949 862 012 F 01949 862 003 E customer care cda eu copyright CDA 2015 www cda eu
15. wcuon E Integrated Dishwasher Installation Use and Maintenance The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance This appliance is not designed to be used by people including children with reduced physical sensorial or mental capacity or who lack experience or knowledge about it unless they have had Supervision or instructions on how to use the appliance by someone who is responsible for their safety Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel Appliance information Please enter the details on the appliance rating plate below for reference to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes Appliance Model _ SerialNumber J OOS S This appliance has been designed for domestic use only Commercial use will invalidate the warranty CE Declarations of Conformity This appliance has been designed constructed and marketed in compliance with safety requirements of EEC Directives 2004 108 EC 2006 95 EC IEC436 DIN44990 EN 50242 Availability of this manual in an alternative format A soft copy of this manual is available for download from w
16. ww cda eu IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002 96 EC At the end of its working life the product must be taken to a special local authority waste collection centre or to a dealer providing appli ance recycling services Disposing of a household appliance separately avoids possible nega tive consequences for the environment and health It also enables the constituent materials to be recovered saving both energy and resources As a reminder of the need to dispose of household appli ances separately the product is marked with a crossed out wheeled dustbin amp Read the instructions prior to installation and use of the appliance Do not lean or climb on the open dishwasher door to prevent damage Close the dishwasher door after use to prevent accidents Use only detergents salt and rinse aid specifically designed for dishwashers Do not put solvents in the dishwasher detergent compartment to prevent risk of explosion Only put dishwasher safe items into the dishwasher If in doubt check with the manufacturer of the items Take care when loading the dishwasher to observe the recommendations for best loading practice and also to ensure that sharp objects such as knives are placed blade down to prevent accidents Do not open the dishwasher door when a programme is running If itis necessary to do so then open it only Slightly to allow the dishwasher to pause the programme
Download Pdf Manuals
Related Search