Home
Tecnoware EVO DSP PLUS 2.4 MM
Contents
1. 160 Vac 5 con carico 80 1002 Range Tensione per modo Normale Limite inferiore rientro da modo Batteria 175 Vac 5 Limite superiore uscita da modo Normale 300 Vac x 576 Limite superiore rientro da modo Batteria 290 Vac 5 Frequenza Nominale 50 60 Hz selezione automatica Range Frequenza modo Normale 47 53 Hz 57 63 Hz Fattore di Potenza d Ingresso 0 99 con carico al 100 USCITA Tensione Nominale Monofase 200 208 220 230 240 Vac selezionabile Regolazione Tensione 2 Forma d Onda Inverter Sinusoidale Frequenza Nominale 50 60 Hz selezionabile Frequenza Free Running modo Batteria 50 Hz 0 25 o 60 Hz 0 25 Distorsione Armonica Totale THD lt 3 Carico Lineare lt 6 Carico Non Lineare Fattore di Cresta 3 1 max Overload 100 110 solo allarme acustico 110 130 per 30 sec gt 130 per 100 ms Tempo di Normale lt gt Batteria 0 ms Trasferimento Batteria lt gt Bypass 4 ms tipico Efficienza 93 in modalit On Line 92 in modalit On Line 98 in modalit ECO 98 in modalit ECO BATTERIE Tipo Batterie Piombo acido sigillate senza manutenzione Numero di Batterie 2 4 6 Tensione Nominale Batterie 24 Vdc 48 Vdc 72 Vdc Specifiche Batterie 12 Vdc 9 Ah Autonomia tipica 8 min Tempo di r
2. Fault code is shown as 27 the icon BATT FAULT Battery Voltage is too Low or lights on LCD display and the Battery Charger is faulty alarm beeps continuously Contact Technical Service UPS EVO DSP PLUS MM 21 User s manual ENGLISH SYMPTOM Fault code is shown as 28 the icon BATT FAULT alarm beeps continuously lights on LCD display and The icons A and flash on LCD display and alarm beeps twice every second Fault code is shown as 43 The icon OVER LOAD lights on LCD display and alarm beeps continuously Fault code is shown as 14 the icon SHORT lights on LCD display and alarm beeps continuously Fault code is shown as 1 2 3 4 11 12 13 41 or 45 on LCD display and alarm beeps continuously Battery backup time is shorter than nominal value The icon A and the warning code F Bass on LCD display and alarm beeps every second POSSIBLE CAUSE Battery Voltage is too Low or the Battery Charger is faulty UPS is overloaded UPS is overloaded Devices connected to the UPS are fed directly by the mains via the Bypass After repetitive overloads the UPS is locked in the Bypass mode Connected devices are fed directly by the mains via the Bypass UPS is overloaded too long and becomes faulty Then UPS shuts down automatically The UPS shuts down automatically because short circuit occurs on the UPS Output A UPS internal fault has occurred There are two possible result
3. Restore the AC Input line for the UPS be sure that the AC utility power is available and that its voltage and frequency are within the specifications As a consequence of point 2 the UPS turns on the graphic display and goes in Stand by mode the UPS recharges only the batteries and doesn t supply Output power Check the graphic display shows the path of energy flow during Stand by mode Press ON MUTE button for at least 3 seconds the UPS emits a brief acoustic signal and performs a functioning SELF TEST After some seconds the UPS starts to work in Normal Mode and the graphic LCD panel will show the path of energy during Normal mode Simulate a black out by removing the AC Input line The UPS starts working in Battery mode the graphic LCD panel will show the path of energy during Battery mode Moreover UPS emits a brief acoustic signal every 4 seconds When Battery level is ending the acoustic signal will be emitted every 1 second Restore the AC Input line after few seconds the UPS turns back in Normal mode The UPS has passed first start up check now turn ON the devices one by one to be supplied by UPS checking the UPS doesn t report Overload information on the graphic LCD panel and all the devices are working regularly By graphic display check if the Output load percentage is less than 100 otherwise it is necessary to remove part of the loads at the Output lines Before using the UPS normally leave it in Normal mode for in
4. It is possible to check the Battery Status when the UPS is running in Normal mode Converter Frequency mode ECO mode by performing a Battery Test To perform the Battery Test press the ON MUTE button continuously for at least 5 seconds The Battery Test starts immediately and it finishes after some seconds If the batteries pass the test no alarm will be shown During the Battery Test the graphic LCD and buzzer indication will be the same as at Battery mode To keep the system reliable the UPS will perform the Battery Test automatically once per week User also can set Battery Test through monitoring software 8 6 Operation in Warning Status During a warning condition the buzzer beeps once every second it means that there are some problems for UPS operation Users can get the Fault code from graphic LCD panel Please check the Troubleshooting chapter for details Below you can see the Warning Table with the correspondence between each warning and the relative signals icons on graphic LCD and acoustic alarm for the user Some acoustic alarms can t be muted unless the error is fixed Please refer to chapter 5 for the details WARNING ICON flashing ACOUSTIC ALARM Low Battery A Beeping every second Overload A OVER LOAD Beeping twice every second Battery Unconnected A Im Beeping every second T Over Charge Beeping every second A Reversed phase for AC Input Line AN
5. bloccata o non funziona oppure la temperatura interna dell UPS troppo alta AZIONI PER RISOLVERE Contattare il Servizio Assistenza Scollegare il carico eccessivo dall Uscita UPS Scollegare il carico eccessivo dall Uscita UPS Scollegare il carico eccessivo dall Uscita UPS poi spegnere UUPS e riaccenderlo Scollegare il carico eccessivo dall Uscita UPS e riaccendere PUPS Controllare i collegamenti d Uscita e se uno dei dispositivi collegati in Uscita provoca la condizione di cortocircuito Contattare il Servizio Assistenza Caricare le batterie per almeno 4 ore e poi ricontrollare autonomia Se il problema persiste contattare il Servizio Assistenza Contattare il Servizio Assistenza per la sostituzione delle batterie Controllare le ventole e contattare il Servizio Assistenza Se le anomalie descritte permanessero nonostante gli interventi consigliati o si manifestassero problemi di altra natura contattare UPS EVO DSP PLUS MM TECNOWARE SERVICE www tecnoware com 45 Manuale utente ITALIANO CE Conformita alle Direttive Europee successive modifiche Sono state applicate le seguenti Normative Direttiva Bassa Tensione Sicurezza EN62040 1 1 2003 Direttiva EMC Compatibilit Elettromagnetica EN62040 2 2006 categoria C2 TECNOWARE S r l dichiara che il prodotto EVO DSP PLUS MM conforme ai requisiti stabiliti nella Direttiva Bassa Tensione
6. 2 L UPS sia completamente spento solo in tal caso il display LCD grafico spento Pulire le superfici esterne usando un panno leggermente inumidito solo con acqua Se U UPS opera in un ambiente insolitamente polveroso o sporco rimuovere la polvere dalle feritoie Prima di riaccendere l UPS accertarsi che sia perfettamente asciutto Se accidentalmente del liquido penetrasse all interno non riattivare l UPS e consultare immediatamente il personale autorizzato per l assistenza 11 2 Batterie Se si prevede di NON utilizzare l UPS per un lungo periodo di tempo prima di lasciare inattivo U UPS assicurarsi che le batterie siano completamente cariche Se il prodotto stato inattivo per pi di 3 mesi prima di riutilizzarlo normalmente svolgere la procedura di Prima Accensione descritta nell omonimo capitolo di questo manuale Tenere comunque presente che le batterie vanno ricaricate almeno 1 volta al mese Si ricorda che l UPS ricarica le batterie automaticamente sia in modo Normale che in modo Stand by Lasciare l UPS in ricarica per circa 4 ore con la Rete elettrica sempre presente in ingresso La durata delle batterie dipende fortemente dalla temperatura dell ambiente di lavoro oltre ad altri fattori quali il numero di cicli di carica scarica la profondit delle scariche l umidit e l altitudine requisiti ambientali per un corretto utilizzo delle batterie sono riportati nel capitolo Caratteristiche Tecnich
7. for example blackouts brownouts over voltages micro interruptions which often cause damage to hardware and software All that is possible because EVO DSP PLUS MM is a Double Conversion ON LINE UPS Under normal AC line condition EVO DSP PLUS MM provides an automatic Output Voltage regulation from the Rectifier and Inverter blocks and filters out frequently occurring electrical disturbances high Voltage transients spikes interferences etc thus protecting the devices connected to its outlets During a power failure EVO DSP PLUS MM continues supplying adequate AC power with a true sine wave to all connected devices through its internal batteries and by its DC AC converter Inverter EVO DSP PLUS MM protects the devices from accidental overload or Inverter fault by an Automatic Bypass that directly connects the AC Input line with its outlets EVO DSP PLUS MM models are factory equipped with RS 232 and USB interfaces which may be used for notify to a computer a power failure or a Low Battery condition this allows automatic data backup during an extended blackout with the most common operating systems Windows Linux Unix etc Thanks to Interfaces UPS DSP MM can communicate the several made measurements Input Output Voltage batteries absorption Frequency etc and can also be programmed in order to start up or shutdown automatically at fixed times Read this manual carefully before using the EVO DSP PLUS MM it includes impo
8. is accepted for about 30 seconds and after UPS switches automatically to the Bypass mode The UPS switches immediately to the Bypass mode if the Overload is higher than than 130 Once the requested power is back within range the UPS switches automatically to the Normal mode Make sure that the UPS never indicates Overload condition Do not connect a load greater than rated value to the UPS see POWER specifications in the chapter Technical Characteristics as this may damage the unit In this case the warranty is void 8 4 Static Bypass During Normal mode functioning it is possible to switch the UPS in Bypass mode by pressing at the same time ON MUTE and SELECT buttons at least 5 seconds as explained into chapter 5 The Bypass mode named also Static Bypass is useful while performing maintenance or service on the UPS The Static Bypass used together with an external Manual Bypass device enables the user to isolate the electronic circuitry of the UPS from the mains and from the load and to remove the UPS without interrupting the power by connecting the load directly to the mains Maintenance and service may only be performed by authorized technical personnel During Static Bypass loads are fed directly from Bypass mains Therefore some protections against AC Input line disturbances or interruptions is present UPS EVO DSP PLUS MM 15 User s manual ENGLISH 8 5 Battery Test
9. metalliche che fermano in pacco batterie scollegare tra di loro le batterie e toglierle dal loro alloggiamento una alla volta Le batterie di EVO DSP PLUS MM non possono essere smaltite come rifiuto urbano ma devono essere smaltite nelle modalit previste dalla direttiva europea 2006 66 CE qualsiasi violazione punita con sanzioni pecuniarie ai sensi della direttiva stessa Pb Manuale utente 46 UPS EVO DSP PLUS MM Copyright 2014 TECNOWARE s r l All rights reserved All trademarks are property of their respective owners TECNOWARE s r l Via Montetrini 2E Molino del Piano Florence Italy www tecnoware com This manual has been printed and edited by TECNOWARE s r l November 2014 Edition Version 1 0 a TECNOWARE power systems TECNOWARE s r l www tecnoware com
10. prego contattare il Servizio Assistenza Tecnoware per le istruzioni Il modo ECO non garantisce perfetta stabilit in frequenza forma d onda valore RMS della Tensione d Uscita come il modo Normale di funzionamento Quindi l uso del modo ECO deve essere utilizzato solo in accordo con il livello di protezione richiesto dai carichi UN my IL modo ECO caratterizzato da ns n ves n ves Il display grafico LDC mostra il percorso del flusso di GIU EJU Q energia durante il modo ECO il simbolo ECO Tka eo Y acceso OS Er a i gt UPS EVO DSP PLUS MM 29 Manuale utente ITALIANO 4 6 Modo CONVERTITORE di FREQUENZA E possibile selezionare il modo Convertitore di Frequenza quando occorre avere la Frequenza d Uscita diversa dalla Frequenza d Ingresso Per esempio possibile lavorare con la Frequenza d Ingresso 60 Hz e la Frequenza d Uscita 50 Hz ed anche con la Frequenza d Ingresso 50 Hz e la Frequenza d Uscita 60 Hz Il modo Convertitore di Frequenza non abilitato dalla fabbrica e la Frequenza d Uscita sempre sincronizzata con la Frequenza d Ingresso Nel caso sia necessario abilitare il modo Convertitore di Frequenza prego contattare il Servizio Assistenza Tecnoware per le istruzioni ce Ey Il modo Convertitore di Frequenza caratterizzato da LF m Vac 3 m Vac e Il display grafico
11. Overload 43 OVER LOAD High Inverter Voltage 12 None Charger failure 45 x Low Inverter Voltage 13 None Fault Table 9 Communication Interfaces The UPS is factory equipped with RS232 and USB Communication Interfaces On the UPS rear side there are the connections of the Interfaces Only one of the RS232 USB communications can be activated at one time To activate RS232 communication it is sufficient to connect the RS232 cable only 9 pins cable pin to pin to activate USB communication it is sufficient to connect the USB cable only The RS 232 and USB signals are all isolated through photo couplers from the dangerous voltages that are present inside the UPS Connecting to the Web site www tecnoware com it is possible to download free of charge the update UPS management Software compatible with the most popular Operative Systems It is possible to use a SNMP Single Network Management Protocol Interface to connect the UPS to a LAN Local Area Network The SNMP interface is optional We advise you to follow the steps below explained to install the interface correctly 1 Remove the metallic panel 3 figure 4 that covers the slot for SNMP interface 2 Put the SNMP Interface into the slot and fix it with screws 3 Connect the LAN cable to SNMP interface and follow the included instruction to make the interface working well UPS EVO DSP PLUS MM 17 User s manual ENGLISH 10 Technical Characteristics UP
12. PLUS MM 31 Manuale utente ITALIANO Pannello LCD Grafico Funzione Informazioni del Tempo di Backup c LLLI H M S Indica quanto tempo trascorso in modo Batteria H ore M minuti S secondi Informazioni di Guasto Fault Indica che si verificata una situazione di Allarme o di Guasto Fault Indica il codice di Fault la lista dei codici riportata nella tabella Tabella Fault nel capitolo 8 Informazioni Allarme Acustic o Indica che l allarme acustico disabilitato Informazioni della Tensione d Uscita Output LLL OO OUTPUT Vac Vdc Hz Indica l Ampiezza e la Frequenza della Tensione d Uscita Vac Ampiezza della Tensione d Uscita Hz Frequenza d Uscita Informazioni del Carico Load 2 a Indica che il livello del carico compreso tra 0 25 26 50 51 75 e 76 100 OVER LOAD Indica la condizione di Sovraccarico Overload SHORT Indica la condizione di corto circuito della linea d Uscita Informazione dell Uscita programmabile Indica che stata impostata una programmazione per l Uscita Programmabile Informazione del Modo di Fun zionamento JO Indica che l UPS connesso alla linea elettrica d Ingresso Indica che la Batteria attiva Indica che il blocco Bypass attivo ECO Indica che stato attivato il modo ECO Indica che il blo
13. Sicurezza 2006 95 CE e successive modifiche e nella Direttiva EMC Compatibilit Elettromagnetica 2004 108 CE e Attenzione EVO DSP PLUS MM un UPS di categoria C2 Quando utilizzato in ambienti residenziali questo prodotto pu produrre radio interferenza nel qual caso pu essere necessario adottare misure aggiuntive da parte dell utilizzatore Smaltimento del Prodotto Il prodotto EVO DSP PLUS MM non pu essere smaltito come rifiuto urbano ma deve esserlo tramite raccolta separata qualsiasi violazione punita con sanzioni pecuniarie ai sensi delle vigenti norme Lo smaltimento non corretto del prodotto o l uso improprio dello stesso o di sue parti dannoso per l ambiente e per la salute umana Il corretto smaltimento dei prodotti recanti il simbolo del bidone segnato da una croce aiuta ad evitare possibili conseguenze negative per l ambiente e la salute umana Batterie al Piombo Il prodotto EVO DSP PLUS MM contiene batterie al piombo acido ermetiche senza manutenzione Tali batterie se manovrate da personale inesperto possono essere causa di shock elettrico e di alte correnti di cortocircuito Per questo motivo la rimozione delle batterie pu essere compiuto solo da personale tecnico specializzato ed autorizzato da Tecnoware In caso contrario Tecnoware declina ogni sua responsabilit Per rimuovere le batterie occorre togliere il coperchio del prodotto poi smontare tutte le parti
14. aane 41 11 Manutenzione eee e es ae e EEO EEE E EEEE Or EEEE EOT ESEESE 43 11 1 Pulizia d l UPS a a rete Ri 43 11 2 Batterie enr ia pee IR EA A OE AAE Me UE wa teed OEC S 43 11 3 Sicurezza dell Operatore cc cee iiia EEE E EEE E E EA EE Aa 43 12 Anomalie ed Interventi ccscecccssccccescccscccssccssccccssccesscessccsssseoess 44 Conformit alle Direttive Europee ooocccocccccocccnnconncocorocnccnnconoroccnonconos 46 Smaltimento del Prodotto cererererrcerreroreeeeeere sere sereseceerereneo 46 Batterie al PiombO iecore Ere ck ornato tosco 46 ENGLISH User s Manual English Safety Warnings Read this manual carefully and completely before installing and using the TECNOWARE EVO DSP PLUS MM Uninterruptible Power Supply which from here after will also be referred to as UPS The UPS must be used only by properly trained personnel To ensure correct and safe operations it is necessary that operators and maintenance personnel observe the general safety Standards as well as the specific instructions included in this manual Risk of electric shock do not remove the cover The UPS contains internal parts which are at a high Voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS which are user serviceable Any repair or maintenance work must be performed exclusively by qualified technical perso
15. all interno dell UPS Collegandosi al sito internet www tecnoware com possibile scaricare gratuitamente la versione aggiornata del software di gestione dell UPS compatibile con i pi diffusi Sistemi Operativi possibile utilizzare un Interfaccia SNMP Single Network Management Protocol per collegare UPS ad una LAN Local Area Network L Interfaccia SNMP interface opzionale Per installare correttamente l Interfaccia SNMP svolgere le seguenti operazioni 1 Rimuovere il pannello metallico n 3 nella figura 4 che copre l alloggiamento slot per l interfaccia 2 Posizionare l interfaccia nell alloggiamento e fissarla al retro dell UPS tramite viti 3 Collegare il cavo LAN all interfaccia e seguire le istruzioni di corredo per attivare l interfaccia Manuale utente 40 UPS EVO DSP PLUS MM ITALIANO 10 Caratteristiche Tecniche Modello UPS EVO DSP PLUS MM 1 2 2 4 3 6 Potenza 1200 VA 2400 VA 3600 VA Potenza Attiva Nominale 840 W 1680 W 2520 W Fattore di Potenza 0 7 Tecnologia On Line Doppia Conversione senza Trasformatore Dimensioni L x H x P 14 5 x 22 x 28 2 cm 14 5 x 22 x 39 7 cm 19 x 31 8 x 42 1 cm Peso Netto 10 kg 17 kg 27 kg INGRESSO Tensione Nominale Monofase 200 208 220 230 240 Vac Limite inferiore uscita da Modo Normale 110 Vac 5 con carico 0 60 120 Vac 5 con carico 60 70 140 Vac 5 con carico 70 80
16. e Beeping every second P Fan failure Over temperature E A A Beeping every second Over temperature t p A Beeping every second Battery Charger failure H A Beeping every second Bypass Voltage out of range Beeping every second Warning Table User s manual 16 UPS EVO DSP PLUS MM ENGLISH 8 7 Operation in Fault Mode When Fault led illuminates and the buzzer beeps continuously it means that there is a fatal error in the UPS Users can get the Fault code from display panel Please check the Troubleshooting chapter for details Please check the loads wiring ventilation mains supply Battery and so on after the fault occurs Don t try to turn ON the UPS again before solving the problems If the problems can t be fixed please contact Technical Service immediately In case of emergency please disconnect the connection from mains supply and Output immediately to avoid further risk or danger Below you can see the Fault Table with each Fault event and the relative FAULT code icon on graphic LCD for the user s information FAULT EVENT FAULT CODE ICON FAULT EVENT FAULT CODE ICON Vdc Bus Start failure 01 None Inverter Output short circuit 14 Vdc Bus Over 02 None Battery Voltage too High 27 BATT FAULT Vdc Bus Under 03 None Battery Voltage too Low 28 BATT FAULT Vdc Bus Unbalance 04 None Over Temperature 41 None Inverter Soft Start failure 11 None
17. heat So it is necessary to leave at least 10 cm of unobstructed space all around the UPS in order to keep it properly ventilated Do not obstruct ventilation holes Do not insert objects or pour liquids in the ventilation holes Do not rest any object on top of the UPS Do not keep liquids flammable gases or corrosive substances near the unit Install the UPS on a properly tiled floor Avoid the installation on a floor that is not tiled flat 4 Operating Modes BYPASS AUTOT output OUTPUT FILTER FILTER NORMAL MODE OUTPUT OUTPUT FILTER BATTERY MODE BYPASS INPUT FILTER BYPASS MODE Figure 1 Operating modes User s manual 4 UPS EVO DSP PLUS MM ENGLISH 4 1 NORMAL Mode The UPS typically works in Normal mode Input mains power is available and its amplitude is within specifications Please refer to figure 1 After the filter has eliminated any high Frequency interference present on the mains the AC Input line is rectified and conditioned in the Rectifier block AC DC conversion the continuous power now enters into the Inverter block and is then reconverted into alternated power DC AC conversion overcoming the Automatic Bypass and feeding the load after an extra filtration At the same time the UPS recharges the batteries through the Battery Charger block Please refer to figure 2 which describe the UPS front panel V Ey The Normal mode is
18. linea elettrica non viene ripristinata entro alcuni minuti allora l UPS si spenge automaticamente proteggendo cosi le batterie da una scarica troppo profonda U UPS smette di erogare potenza in Uscita disattiva le indicazioni del pannello di comando e si pone in uno stato di attesa Al ritorno della linea elettrica l UPS si riaccende automaticamente e dopo 4 secondi ritorna a funzionare in modo Normale Dopo una scarica completa l UPS avr bisogno di circa 4 ore per ricaricare le batterie La ricarica avviene automaticamente se l UPS acceso e funzionante in modo Normale o in modo Bypass ed anche in modo Stand by UPS EVO DSP PLUS MM 37 Manuale utente ITALIANO 8 3 Controllo del Carico L UPS indica il livello del carico in Uscita per mezzo del display grafico visualizzandolo a destra come descritto nel capitolo 5 Quando il carico in Uscita supera il valore nominale l UPS segnala la condizione di Overload Sovraccarico per mezzo del display grafico e dell allarme acustico come descritto nella Tabella Allarmi e nel capitolo Anomalie ed Interventi L UPS segnala un Overload minore del 110 con allarme acustico L UPS ha la capacita di sopportare un Overload compreso tra il 110 e il 130 per 30 secondi e dopo commuta automaticamente in modo Bypass Se invece l Overload maggiore del 130 UPS commuta immediatamente in modo Bypass Se la condizione di Overload scompare dopo alcuni secondi PUPS ricom
19. or IEEE elsewhere for the Input Output connections and for the right selection of Input Output cables For safety we recommend using external circuit breakers between Input mains and UPS AN AC Input line and between UPS Output lines and the loads The circuit breakers should be qualified with leakage current protective function leakage current lt 30 mA For the Input Output connections use ONLY the included power cables or cables with the same power ratings TECNOWARE declines any responsibility if this warning is disregarded The EVO DSP PLUS MM models are made of a single unit design that contains the electronic parts and batteries Before starting the installation procedure be sure that AN 1 The AC Input Voltage for the UPS has been removed 2 The UPS is completely OFF only if graphic LCD panel is OFF 6 1 Installation We advise you to follow the steps below explained 1 Through the included power cable connect the UPS Input socket to the AC line outlet see figure 4 It is mandatory to ground the AC line outlet according to the Safety Standards Carefully check the grounding of AC line outlet 2 Connect the devices to be supplied to the UPS outputs by using only the included cables Be sure all the devices have the main switch in OFF position User s manual 12 UPS EVO DSP PLUS MM ENGLISH A connected to AC utility line I It is compulsory to ground the UPS according to t
20. Battery Test section for more information on Battery Test Danger of explosion and fire if batteries of the wrong type or number are used Do not dispose of batteries in a fire The batteries may explode Do not open or mutilate batteries Released electrolyte is harmful to the skin and eyes It may be toxic 11 3 Operator Safety Whenever the UPS is not responding anymore to original characteristics the UPS must be made non operative and every usage not authorised must be avoided After it will be necessary to refer to qualified technical personnel Original safety characteristics might not be if for example the UPS has visible damage or irregular operation User s manual 20 UPS EVO DSP PLUS MM ENGLISH 12 Troubleshooting This section gives information about the procedures which shall be performed in case of abnormal operation If you fail to fix the problem consult authorized Technical Service with the following information Model and serial number of the UPS which can be found on the nameplate on the rear of the UPS Description of abnormal operation and Fault code displayed on graphic LCD If you have noticed an abnormality in operation check the Protective Ground Earth connections check the Input Output connections read alarms code from the graphic LCD and refer to the table below Apply all suggestions corresponding to each anomaly If your issue is excluded or the suggested actions do not sol
21. LDC mostra il percorso del flusso di 230 Cio Q energia durante il modo Convertitore di Frequenza Il display visualizza i caratteri CF C i t E53 IS 5 Descrizione Esterna 5 1 Pannello Frontale Il pannello frontale informa l utente sullo stato di funzionamento sulle condizioni di allarme e sulle misure Inoltre consente di controllare e configurare i parametri di funzionamento Il pannello frontale mostrato nella figura 2 costituito da 2 parti 1 Un pannello LCD grafico che fornisce le informazioni complete sul percorso del flusso energia per i vari modi di funzionamento sugli allarmi esistenti sul carico in Uscita sulle batterie e sulle misure delle grandezze elettriche della linea d Ingresso d Uscita e delle batterie 2 3 pulsanti che permettono di attivare e disattivare l UPS svolgere altre funzioni e fare la selezione dei parametri di funzionamento Manuale utente 30 UPS EVO DSP PLUS MM ITALIANO ERAS m E3 Vde Hz Hz 9 ON MUTE SELECT Figura 2 Pannello Frontale 5 1 1 Pannello LCD Grafico Prego riferirsi alla figura 3 Info Tensione Info Info Allarme Info d Ingresso e di Batteria 4 3 TempoBackup Info Fault Acustico Tensione d Uscita em HC s DO Info Batteria II RATT FAULT a S LL u A I Lo m v v Info Modo di Info Output Funzionamento Programmabile Figura 3 Pannello LCD grafico UPS EVO DSP
22. O DSP PLUS MM 27 Manuale utente ITALIANO 4 1 Modo NORMALE il modo tipico di funzionamento In questo caso la Tensione di Rete elettrica presente in Ingresso ed ha ampiezza all interno delle specifiche Fare riferimento alla figura 1 La Tensione d Ingresso dopo che il filtro ha eliminato eventuali disturbi in alta frequenza presenti sulla Rete elettrica viene raddrizzata e condizionata nel blocco Raddrizzatore conversione CA CC la potenza continua cos ottenuta entra nel blocco Inverter in cui viene riconvertita in potenza alternata conversione CC CA che supera il Bypass Automatico e alimenta dopo un ulteriore filtraggio il carico in Uscita Contemporaneamente l UPS ricarica le batterie tramite il blocco Carica Batterie Fare riferimento alla figura 2 che descrive il pannello frontale dell UPS Na my IL modo Normale caratterizzato da am n q cau 230 f Il display grafico LDC mostra il percorso del flusso di energia durante il modo Normale SoD B Ga t S 3 I 4 2 Modo BATTERIA Se durante il funzionamento nel modo Normale UUPS rileva la condizione di Assenza Rete dovuta ad un black out oppure ad una variazione dell ampiezza della Tensione di Rete oltre le specifiche allora passa nel modo Batteria In questo caso sono le batterie che forniscono la potenza necessaria in Uscita grazie sempre alla conversione CC CA svolta dall Inverter Quand
23. P b The batteries cannot be disposed as an urban waste but must be treated in conformity with 2006 66 CE European Directive any violation is indictable with financial sanctions as established into 2006 66 CE European Directive UPS EVO DSP PLUS MM 23 User s manual ITALIANO Manuale Utente Italiano Avvisi di Sicurezza Leggere attentamente e completamente questo manuale prima di installare ed utilizzare il gruppo di continuita TECNOWARE della serie EVO DSP PLUS MM che in seguito verra chiamato anche semplicemente UPS L UPS deve essere utilizzato solo da personale opportunamente istruito Per l uso corretto e in condizioni di sicurezza necessario che gli operatori ed il personale di manutenzione si attengano alle norme generali di sicurezza in aggiunta alle norme specifiche contenute in questo manuale Rischio di shock elettrico non rimuovere il coperchio L UPS presenta parti interne sotto tensione che sono potenzialmente pericolose e possono provocare lesioni o morte per shock elettrico L UPS non ha parti interne soggette a manutenzione da parte dell utente Interventi tecnici di qualsiasi tipo devono essere compiuti solo da personale tecnico specializzato ed autorizzato da TECNOWARE In caso contrario TECNOWARE declina ogni sua responsabilit L installazione elettrica nonostante la sua semplicit deve essere eseguita esclusivamente da elettricisti qualificati Seguire scrupolosamente tutte le norme
24. S EVO DSP PLUS MM Model 1 2 2 4 3 6 Power 1200 VA 2400 VA 3600 VA Nominal Active Power 840 W 1680 W 2520 W Power Factor 0 7 Technology On Line Double Conversion Transformerless Dimension W x H x D 14 5 x 22 x 28 2 cm 14 5 x 22 x 39 7 cm 19 x 31 8 x 42 1 cm Net Weight 10 kg 17 kg 27 INPUT Nominal Voltage Single Phase 200 208 220 230 240 Vac Lower Limit transfer to Battery mode 110 Vac 5 at 0 60 load 120 Vac 5 at 60 70 load 140 Vac 5 at 70 8076 load 160 Vac 5 at 80 100 load Voltage Range for Normal mode Lower Limit come back to Line mode 175 Vac 5 Upper Limit transfer to Battery mode 300 Vac 5 Upper Limit come back to Line mode 290 Vac 5 Nominal Frequency 50 60 Hz automatic selection Frequency Range Normal mode 47 53 Hz 57 63 Hz Input Power Factor 0 99 at 100 Load OUTPUT Nominal Voltage Single Phase 200 208 220 230 240 Vac selectable Voltage Regulation 2 Inverter Waveform True Sinewave Nominal Frequency 50 60 Hz selectable Free Running Frequency Battery mode 50 Hz 0 25 or 60 Hz 0 25 Total Harmonic Distortion THD lt 3 Linear Load lt 6 Non Linear Load Crest Factor 3 1 max Overload 100 110 only acoustic alarm 110 130 for 30 sec gt 130 per 100 ms No
25. a TECNOWARE power sy ste ms Uninterruptible Power Supply EVO DSP PLUS MM 1 2 EVO DSP PLUS MM 2 4 EVO DSP PLUS MM 3 6 User s manual Manuale utente Index User s Manual Enelish 5 or iure sais 1 Safety Warnings iris vo eere ese terea eoe eoe esee se ure eu Peer Pe evs eee Ta eser eoe 1 1 Introd ction eee eee eee eroe serre prr ese nere eve e ore Nove eee Pe ev RE ERES 2 2 General Characteristics ceci c ee eee re eee ern eet I ee eR Share Re Ehe rela Ehe eee 3 3 Receipt and site selection 1e eee eee ree ere een eta nhan eoa ehe ria nera io 3 4 Operating Modes 2 i esos eie erinedes bared ersen ise ea ops da eb arose nada 4 4 1 NORMAL Mode eser sees herede IR e de SR Te dace seve ede Ee Tes en sere tee 5 4 2 BATTERY Mode ess eee dee eue aaa 5 4 3 BYPASS ModS seseris os eee ene ind 5 4 4 STAND BY Mode 1 e t re e alal xe ee eed ned Seen 6 4 5 ECO Mode talia er SE es das bes 6 4 6 CONVERTER FREQUENCY Mode cce cece cece ce e e nh ehh eene 7 5 EXTERNAL DESCRIPTION cocaina 7 DEM Eront Panel ds ls ds ll Ia 7 5 1 1 Graphic LCD Panel cinc a ns ca oriana seeds 8 5 1 2 Buttons tai 10 5 13 gt Acoustic Ad aaa iii 11 5 2 REAM Side ll ae edera rata 11 5 Electrical Installations sive uc cacaos ia aceras 12 6 1 Installation a dd elle NI T 12 First Start Upa tas 13 FUNCHIONINZ siii e das 14 8 1 Turning ON arid O Fresita ila na 14 8 2 Low Batte
26. alsiasi tipo black out sottotensioni sovratensioni surge spike microinterruzioni interferenze Tutto ci possibile perch EVO DSP PLUS MM un gruppo di continuit ON LINE doppia conversione Durante il normale funzionamento EVO DSP PLUS MM converte la potenza d Ingresso da alternata a continua nel blocco Raddrizzatore e poi da continua ad alternata nel blocco inverter grazie a questa doppia conversione il grado di protezione per il carico diventa assoluto Al verificarsi di una qualsiasi avaria della linea elettrica la potenza richiesta continua ad essere fornita tramite le batterie senza nessuna interruzione La sicurezza per le utenze alimentate garantita anche in caso di sovraccarico accidentale oppure di guasto inverter grazie ad un Bypass automatico che esclude EVO DSP PLUS MM e collega direttamente la linea elettrica d Ingresso alle uscite EVO DSP PLUS MM dotato d interfacce di comunicazione RS232 e USB che possono essere utilizzate per segnalare ad un generico elaboratore o computer le condizioni di assenza Rete e di fine autonomia ci rende possibile lo svolgimento delle funzioni di salvataggio automatico dei dati durante un black out prolungato con i pi diffusi sistemi operativi Windows Linux Unix etc Grazie alle interfacce EVO DSP PLUS MM pu inoltre comunicare le varie misurazioni fatte Tensione d Ingresso d Uscita e di batterie assorbimento frequenza etc e pu anche essere programmat
27. ance 11 1 UPS Cleaning Before starting any cleaning operation be sure that 1 The AC Input Voltage for the UPS has been removed 2 The UPS is completely OFF the graphic LCD panel is OFF Use only a cloth dampened with water to clean the unit If UPS works in an environmental unusually dusty or dirty remove the dirty from the ventilation holes Before restarting the UPS be sure it is completely dry If any liquid gets inside the UPS do not start the unit and contact Technical Service immediately 11 2 Battery If the UPS is NOT going to be used for a long period of time ensure that the batteries are left fully charged If the UPS has not been used for more than three months go through the procedure described in the chapter 7 First Start Up before using it again Please keep in mind that the batteries must be recharged at least once a month Take in mind that batteries are recharged automatically if the UPS is ON and working in Normal or in Bypass mode for after approximately 4 hours with AC Input line present Battery life strongly depends on the ambient temperature There are also other factors like the number of charge discharge cycles the discharge depth humidity and altitude The recommended environmental specifications for a correct use of batteries are listed in the Technical Specifications section Performing Battery Test can provide you with information about Battery condition see
28. atterie si sta esaurendo U UPS emette il segnale acustico ogni secondo Ripristinare la Tensione di Rete elettrica in Ingresso dopo alcuni secondi U UPS ritorna nel modo Normale L UPS ha superato il controllo di prima accensione basta accendere uno alla volta tutti i dispositivi collegati alle Uscite dell UPS controllando che l UPS non dia indicazioni di Sovraccarico Overload sul display grafico e che tutti i dispositivi si siano accesi regolarmente Inoltre controllare la percentuale di carico in Uscita tramite il display grafico assicurandosi che il valore sia inferiore al 100 altrimenti necessario rimuovere parte del carico in Uscita Prima di poter utilizzare normalmente UPS EVO DSP PLUS MM si consiglia di lasciarlo acceso in modo Normale per caricare le batterie si ricorda che la ricarica delle batterie viene svolta anche in modo Bypass e in modo Stand by Le batterie raggiungono il 90 della loro capacit dopo circa 4 ore di carica Manuale utente 36 UPS EVO DSP PLUS MM ITALIANO 8 Funzionamento 8 1 Accensione e Spegnimento Vediamo con attenzione le conseguenze della pressione dei pulsanti ON MUTE e OFF L UPS in modo Stand By Inverter disattivo se viene premuto il pulsante ON MUTE dopo alcuni secondi l UPS attiva Inverter e commuta nel modo Normale L UPS in modo Normale Inverter attivo se viene premuto il pulsante OFF l UPS disattiva Inverter e commuta nel modo Stand by Per sp
29. cco Inverter attivo 0 Indica che l Uscita UPS attiva Manuale utente 32 UPS EVO DSP PLUS MM ITALIANO Pannello LCD Grafico Funzione Informazione della Batteria Indica che la capacit della Batteria compresa tra 0 25 26 50 51 75 e 76 100 BATT FAULT Indica che la Batteria guasta Indica la condizione di Batteria scarica Low Battery e quindi di bassa Tensione Batteria Informazioni della Tensione d Ingresso Input e della Tensione Batteria Indica l Ampiezza e la Frequenza della Tensione d Ingresso Input e la Tensione Batteria Vac Ampiezza della Tensione d Ingresso Vdc Tensione Batteria Hz Frequenza d Ingresso 5 1 2 Pulsanti Le funzioni dei pulsanti presenti sul pannello frontale sono riportate sotto Pulsante Funzione ON MUTE Attiva ON PUPS per attivare PUPS premere e mantenere premuto il pulsante per almeno 3 secondi Disattiva attiva l allarme acustico durante il funzionamento in modo Batterie per disattivare l allarme acustico premere e mantenere premuto il pulsante per almeno 5 secondi Se si preme il pulsante quando l allarme acustico disattivo allora l allarme acustico si riattiva nuovamente Test Batteria per svolgere un Test Batteria premere e mantenere premuto il pulsante per pi di 5 secondi durante il funzionamento in modo Normale SELECT Seleziona la grand
30. ders rere ce re ere nera ee ra eror rosea s eee Toe ease rds 28 4 2 Modo BATTERIA iii 28 4 3 Modo BYPASS ode ree dc eode et 28 4 4 Modo STAND BY riore 29 4 5 Modo ECO lol o iii 29 4 6 Modo CONVERTITORE di FREQUENZA ccceeecceenceceeseeeenceeeeeeees 30 5 Descrizione Esterna e eee erereecerererrresee eee nee ehe eene nnns 30 5 1 Pannello Frontales 30 5 1 1 Pannello LCD Grafico ertt erret teh nra enr eh e pr R e PY S vies 31 5 12 PUlsanti EE 33 5 123 Allarme AcUStICO viii A e eau a Cu kae E e EE EUCH E 34 5 2 Pannello POSteriOre 2 io see efe deed cose en eves eager ses sede ds 34 6 Installazione Elettrica coord earn 35 6 1 Installazionez dd 35 Prima AccenisiOne icio cetero re tret rra rro e eae P ao rose eere Pra Pa 36 Funzionamento rara 37 8 1 Accensione e Spegnimento L00000e eee iii eee eee eene 37 8 2 Fine Autonomia e Riaccensione Automatica c 00000 37 8 3 Controllo delCarico o oreet ee Ede ive ERSTES c E eere dg 38 8 4 Bypass Statico eee dee A ARR e ex A e du EA E E ceed ate 38 8 5 Test Batteria ARR SERE seeks daw EE RN x ua e EE e 39 8 6 Segnalazioni di Allarme L Lecci nee enhn 39 8 7 Segnalazioni di GUASTO us a A UD esee 40 9 Interfacce di Comunicazione ooooocconccccconccnnconorocaronccnnconoroccnonconos 40 10 Caratteristiche Tecniche eee eee e ree oe eee n een Ee ee rene no eeu o onu rona noue
31. di Fault 27 acceso il simbolo BATT FAULT e Vallarme acustico suona continuamente Manuale utente Il cavo della linea d Ingresso Rete non connesso correttamente alla presa d Ingresso dell UPS L interruttore Termico d Ingresso Rete scattato OFF Sono invertiti i poli FASE e NEUTRO della linea d Ingresso Rete Le batterie interne e o esterne sono collegate non correttamente La Tensione Batteria troppo alta o il Carica Batteria guasto 44 Controllare accuratamente il cavo d Ingresso Rete e il collegamento alla linea d Ingresso Rete Riattivare ON l Interruttore Termico premendo manualmente sulla parte fuoriuscita Scollegare la spina del cavo d ingresso dalla presa della linea d Ingresso Rete ruotarla di 180 gradi e ricollegarla alla presa Controllare i collegamenti delle batterie interne e o esterne Contattare il Servizio Assistenza UPS EVO DSP PLUS MM ITALIANO ANOMALIA Sul display grafico visualizzato il codice di Fault 28 acceso il simbolo BATT FAULT e Vallarme acustico suona continuamente simboli A e lampeggiano sul display grafico e l allarme acustico suona 2 volte ogni secondo Sul display grafico visualizzato il codice di Fault 43 acceso il VER LOAD simbolo OVER LO e Vallarme acustico suona continuamente Sul display grafico visualizzato il codice di Fault 14 acceso il simbolo SHORT
32. e In qualsiasi momento possibile avere le informazioni della condizione delle batterie svolgendo il Test Batteria vedi il capitolo Test Batteria per maggiori informazioni Pericolo di esplosione o di incendio se si utilizzano batterie di tipo sbagliato o un numero errato di batterie Non avvicinare le batterie al fuoco Le batterie possono esplodere Non aprire o danneggiare le batterie L elettrolita contenuto nelle batterie che pu fuoriuscire nocivo alla pelle e agli occhi 11 3 Sicurezza dell Operatore Qualora l UPS non presenti pi le caratteristiche di sicurezza originali lo stesso deve essere reso non operativo e ne deve essere evitato un utilizzo non autorizzato Si dovr poi riferire il problema a personale tecnico qualificato Le caratteristiche di sicurezza originali possono venire meno se per esempio L UPS presenta dei danni visibili o un funzionamento anomalo UPS EVO DSP PLUS MM 43 Manuale utente ITALIANO 12 Anomalie ed Interventi Questo capitolo descrive le procedure che devono essere seguite in caso di funzionamento anomalo Nel caso in cui le azioni consigliate per risolvere l anomalia non avessero esito positivo contattare il Servizio Assistenza Fornire al Servizio Assistenza le seguenti informazioni Modello e numero di serie dell UPS stampati nell etichetta sul retro del prodotto Descrizione del funzionamento anomalo e codice Fault visualizzato
33. e Vallarme acustico suona continuamente Sul display grafico visualizzato il codice di Fault 1 2 3 4 11 12 13 41 o 45 l allarme acustico suona continuamente L autonomia delle batterie inferiore al valore nominale Il simbolo A e il codice d allarme FA lampeggiano sul display grafico e l allarme acustico suona ogni secondo POSSIBILE CAUSA La Tensione Batteria e troppo bassa o il Carica Batteria guasto L UPS e in condizioni di Overload Sovraccarico L UPS in condizioni di Overload Sovraccarico dispositivi connessi all Uscita UPS sono alimentati direttamente dalla linea di Rete elettrica attraverso la via di Bypass Si sono verificati ripetuti Overload UUPS bloccato in modo Bypass dispositivi connessi all Uscita UPS sono alimentati direttamente dalla linea di Rete elettrica attraverso il Bypass L UPS stato in condizioni di Overload troppo a lungo L UPS si disattivato automaticamente segnalando una situazione di guasto L UPS si e disattivato automaticamente perch si verificato un cortocircuito in Uscita dell UPS L UPS ha un guasto interno In seguito al guasto si pu avere una delle 2 situazioni seguenti 1 Il carico ancora alimentato direttamente dalla linea d Ingresso attraverso il Bypass 2 Il carico non alimentato Le batterie non sono completamente cariche La batterie sono esaurite Una o pi ventola
34. e alcune protezioni contro i disturbi e le interruzioni della linea elettrica Manuale utente 38 UPS EVO DSP PLUS MM ITALIANO 8 5 Test Batteria Per controllare lo stato delle batterie possibile svolgere un Test Batteria durante il funzionamento in modo Normale in modo ECO e in modo Convertitore di Frequenza Per svolgere il Test Batteria sufficiente premere il pulsante ON MUTE del pannello frontale continuativamente per almeno 5 secondi il test si avvia immediatamente e si conclude dopo alcuni secondi Se il test superato UUPS non segnala nessun allarme Durante il Test Batteria il display grafico e l allarme acustico forniscono le stesse indicazioni del funzionamento in modo Batteria Per mantenere il sistema affidabile PUPS svolge comunque il Test Batteria automaticamente una volta alla settimana L utente pu anche impostare il Test Batteria tramite il software di monitoraggio e controllo 8 6 Segnalazioni di Allarme La condizione di Allarme segnalata dall emissione dell allarme acustico una volta ogni secondo tipi di Allarme che si possono verificare durante il normale funzionamento sono elencati nella Tabella Allarmi sotto riportata Per ogni allarme indicato anche il simbolo che lampeggia sul display grafico Per maggiori dettagli consultare il capitolo Anomalie ed Interventi In alcuni casi l allarme acustico pu essere disattivato tramite il pulsante ON MUTE come spiegat
35. egnere completamente l UPS occorre Premere il pulsante OFF provocando il passaggio in modo Stand by gt Scollegare la linea elettrica d Ingresso all UPS Il display LCD grafico spento solo quando l UPS completamente spento Se si utilizza quotidianamente UUPS si consiglia di lasciare UPS collegato sempre alla Rete elettrica in Ingresso e utilizzare i pulsanti ON MUTE ed OFF del pannello frontale per attivare e disattivare l Inverter Se invece si prevede di tenere disattivo PUPS per alcuni giorni allora si consiglia di scollegare U UPS dalla Rete Elettrica d Ingresso e spegnere cosi totalmente l UPS Se premuto il pulsante ON MUTE quando non presente la Tensione di Rete elettrica in Ingresso U UPS si accende ugualmente dopo alcuni secondi attiva l Inverter e comincia a funzionare nel modo Batteria Se premuto il pulsante OFF quando non presente la Tensione di Rete elettrica in Ingresso l UPS disattiva l Inverter e si spegne completamente e di conseguenza smette di fornire potenza in Uscita 8 2 Fine Autonomia e Riaccensione Automatica L UPS raggiunge la condizione di Fine Autonomia o Low Battery quando durante il funzionamento in modo Batteria le batterie sono scariche al punto da garantire soltanto alcuni minuti di autonomia L UPS avvisa l utente della condizione di Fine Autonomia accendendo il simbolo LOW BATT sul display grafico ed emettendo un segnale acustico ogni secondo Se la
36. entazione elettrica 2 Collegare i dispositivi da alimentare alle prese d Uscita dell UPS utilizzando i cavi d uscita in dotazione Assicurarsi che tutti i dispositivi collegati siano spenti UPS EVO DSP PLUS MM 35 Manuale utente ITALIANO Il collegamento a terra dell UPS secondo le norme vigenti obbligatorio Il mobile dell UPS connesso internamente ai morsetti di terra GND della morsettiera d Ingresso Uscita per garantire la sicurezza dell operatore perch questa sicurezza sia effettiva necessario assicurarsi che l impianto elettrico locale sia provvisto di collegamento a TERRA GROUND conforme alle norme e che sia garantita una valida connessione tra la TERRA GROUND dell UPS e la TERRA GROUND dell impianto Ogni interruzione del conduttore di TERRA GROUND assolutamente vietata Rischio di shock elettrico in Uscita se l UPS acceso anche se non presente la AN Tensione di Rete Elettrica in Ingresso Rischio di shock elettrico in Uscita se presente la Tensione di Rete Elettrica in Ingresso Non smontare l UPS contiene parti sotto tensione che sono potenzialmente pericolose e possono provocare lesioni o morte per shock elettrico L UPS non ha parti interne soggette a manutenzione da parte dell utente Interventi tecnici di qualsiasi tipo devono essere compiuti solo da personale tecnico specializzato ed autorizzato da TECNOWARE In caso contrario TECNOWARE declina ogni sua responsabi
37. ezza da visualizzare sul display grafico tramite la pressione del tasto SELECT possibile scegliere la grandezza elettrica che viene visualizzata sul display possibile visualizzare la Tensione d Ingresso la Frequenza d Ingresso la Tensione Batteria la Tensione d Uscita e la Frequenza d Uscita Se non viene premuto il tasto per 10 secondi sul display ritornano ad essere visualizzate le grandezze di default Tensione d Ingresso e Tensione d Uscita OFF Disattiva OFF PUPS per disattivare PUPS premere e mantenere premuto il pulsante per almeno 3 secondi Se si preme il pulsante OFF mentre l UPS funziona in modo Normale UUPS si disattiva e va in modo Stand by Se si preme il pulsante OFF mentre l UPS funziona in modo Batteria l UPS si spegne completamente ON MUTE SELECT Passaggio in modo Bypass durante il funzionamento in modo Normale premendo contemporaneamente i 2 pulsanti ON MUTE e SELECT per almeno 5 secondi l UPS commuta in modo Bypass Il passaggio non si verifica se la Tensione di Rete in Ingresso non all interno del range accettabile come Tensione di Bypass Per ritornare in modo Normale premere nuovamente i 2 pulsanti ON MUTE e SELECT per almeno 5 secondi UPS EVO DSP PLUS MM 33 Manuale utente ITALIANO 5 1 3 Allarme Acustico Stato UPS Allarme acustico OFF Modo Batteria Allarme acustico ogni 4 secondi SI Low Battery Fine Autono
38. f the acceptable range User s manual 10 UPS EVO DSP PLUS MM ENGLISH 5 1 3 Acoustic Alarm UPS status Acoustic Alarm OFF Battery Mode Beeping once every 4 seconds YES Low Battery Beeping once every second Overload Beeping twice every second NO Fault Mode Beeping continuously Bypass Mode Beeping once every 10 seconds Note OFF YES means that the buzzer can be muted or stopped by pressing ON MUTE button OFF NO means that the buzzer can NOT be muted or stopped 5 2 Rear Side EVO DSP PLUS MM 1 2 EVO DSP PLUS MM 2 4 EVO DSP PLUS MM 3 6 Figure 4 Rear Side 1 Computer Interface DB9 female connector it is the communication RS 232 port Computer Interface USB connector it is the communication USB port Slot for SNMP Interface optional Grounded AC Input power socket to connect the UPS to the AC utility line by the included power cord 0 Aa W N Input Circuit Breaker it goes off in Overload or short circuit condition push the external button of the Circuit Breaker to reactivate it o Grounded Output Receptacles IEC C13 type to supply critical loads 7 Grounded Output Terminal Block to connect an Output power line to supply all the devices to be protected UPS EVO DSP PLUS MM 11 User s manual ENGLISH 5 Electrical Installation The electrical installation has to be done by qualified personnel Follow all the Safety Standards CEI Standards in Italy
39. he Safety Standards The case of the UPS is internally connected to the ground terminal GND of the IN OUT terminals in order to guarantee safety to the user To guarantee safety it is necessary to be sure that the local electric plant is supplied with GROUND in compliance with the Safety Standards and that a valid connection is guaranteed between the GROUND of the UPS and the GROUND of the local electric plant Any interruption of the GROUND conductor is absolutely prohibited Risk of electric shock at the Output lines if the UPS is ON even when the UPS is not Risk of electric shock at the Output lines while the unit is connected to the AC utility line Risk of electric shock do not remove the cover The UPS contains internal parts which are at a high Voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS which are user serviceable Any repair or maintenance work must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded Disregard for these warnings may lead to a risk of electric shock to operators 7 First Start Up Turning the UPS ON is very easy Nevertheless we recommend that on First Start Up the following procedure is observed for greater safety 1 2 Be sure all the devices connected to the UPS outputs have the main switch in OFF position
40. hes OFF and consequently there will be no Output power 8 2 Low Battery and Automatic Restart The UPS reaches the Low Battery condition whenever during working in Battery mode the batteries reach a charge level allowing the connected devices to operate for few minutes more The UPS warns operators of Low Battery by lighting of the LOW BATT icon on the graphic LCD and by emitting an acoustic signal every second If AC Input does not come back on within few minutes the UPS shuts down automatically thus preventing the batteries from discharging excessively the UPS stops supplying Output power deactivates control panel indication and goes to a waiting state Once AC Input comes back on the UPS restarts automatically and after 4 seconds it goes back to work in Normal mode After a complete discharge the UPS needs 4 hours to recharge completely the batteries The UPS recharges batteries automatically if it works in Normal mode in Bypass mode or in Stand By mode User s manual 14 UPS EVO DSP PLUS MM ENGLISH 8 3 Load Testing The UPS indicates the Output Load level by graphic LCD on the right side as described in the chapter 5 When the Output load is higher then nominal value the UPS warns of Overload condition by graphic LCD and by acoustic alarm as described in the Warning Table and in the Troubleshooting chapter The UPS warns of an Overload less than 110 by acoustic alarm An Overload between 110 and 130
41. i qualificati Seguire scrupolosamente tutte le norme locali e nazionali in ITALIA le norme CEl per le connessioni d Ingresso e d Uscita e per il corretto dimensionamento dei cavi d Ingresso e d Uscita Per la sicurezza degli operatori occorre posizionare degli interruttori esterni tra la linea elettrica d Ingresso e la linea d Ingresso dell UPS e tra le linee d Uscita dell UPS e carichi Gli interruttori hanno la funzione di protezione e sicurezza e devono essere scelti con la specifica di corrente di dispersione inferiore a 30 mA Per i collegamenti d Ingresso Uscita utilizzare esclusivamente i cavi in dotazione con il prodotto o cavi con analoghe caratteristiche In caso contrario TECNOWARE declina ogni sua responsabilit I modelli EVO DSP PLUS MM sono costituiti da un unit singola che contiene sia l elettronica che le batterie Prima di avviare la procedura d installazione accertarsi che 1 La linea elettrica d Ingresso all UPS sia scollegata 2 L UPS sia completamente spento solo in tal caso il display LCD grafico spento 6 1 Installazione Svolgere le seguenti operazioni 1 Tramite il cavo di alimentazione in dotazione collegare la presa d Ingresso rete vedi figura 4 ad una presa di alimentazione elettrica che deve avere obbligatoriamente una connessione a terra secondo le norme vigenti Verificare accuratamente il collegamento a terra della presa d alim
42. icarica Batterie tipico 4 ore UPS EVO DSP PLUS MM 41 Manuale utente ITALIANO CARATTERISTICHE AMBIENTALI Range Temperatura Immagazzinamento da 25 C a 55 C si consiglia da 15 C a 40 C per avere una pi lunga vita delle batterie Range Temperatura Funzionamento da 0 C a 40 C si consiglia da 20 C a 25 C per avere una pi lunga vita delle batterie Range Umidit Relativa 0 95 senza condensazione Altitudine Massima senza Declassamento 3000 m Livello di Protezione IP 20 Raffreddamento Forzato tramite ventole Rumorosit ad 1 metro lt 45 dBA CONFORMIT ALLE NORME Sicurezza EN 62040 1 1 EN 60950 1 Prestazioni EN 62040 3 EMC EN 62040 2 categoria C2 Certificazione del Prodotto CE INTERFACCE DI COMUNICAZIONE Interfaccia Computer 1 porta RS232 e 1 porta USB Software di Comunicazione Di serie software compatibile con Windows Mac OS X fino versione 10 8 Linux Novell Interfaccia SNMP Opzionale ALTRE SPECIFICHE Modo ECO Selezionabile Modo Convertitore di Frequenza Selezionabile dati tecnici sono soggetti a variazioni senza preavviso Manuale utente 42 UPS EVO DSP PLUS MM ITALIANO 11 Manutenzione 11 1 Pulizia dell UPS Prima di avviare la procedura d installazione accertarsi che 1 La linea elettrica d Ingresso all UPS sia scollegata
43. identified by gt m Vac 3 m Vac The graphic LCD panel shows the path of energy flow E eau e3u f during Normal mode G 0228 i t S E3 e IS 4 2 BATTERY Mode During operation in Normal mode if the UPS finds the Mains OFF condition due to a Blackout or Overvoltage Brownout it then switches into Battery mode In this case the batteries supply the required Output power thanks to the DC AC conversion carried out by the Inverter The UPS switches back to Normal mode a few seconds after AC Input power is restored or Voltage comes back to internal specifications Please refer to figure 1 va EM The Battery mode is identified by jm e e The graphic LCD panel shows the path of energy flow m mm during Battery mode E a bc Em n acoustic signal every 4 seconds E U 4 3 BYPASS Mode In Bypass mode the AC Input line is directly connected with the UPS outlets by an Automatic Bypass As indicated in figure 1 in Bypass mode the UPS recharges the batteries During Normal mode the UPS switches automatically to Bypass mode as a consequence of accidental overload or Inverter fault thus protecting the supplied devices When the UPS is working in Normal mode it is possible to switch the UPS by pressing continuously ON MUTE and SELECT buttons at the same time for at least 5 seconds as explained into chapter 5 UPS EVO DSP PLUS MM 5 User
44. ischi o danni disconnettere l UPS dalla linea d Ingresso e dalle linee d Uscita Di seguito riportata la Tabella Fault con elencati tutti i tipi di Fault possibili e per ognuno indicato il codice Fault e il simbolo visualizzati sul display grafico TIPO DI GUASTO FAULT CODICE SIMBOLO TIPO DI GUASTO FAULT CODICE SIMBOLO Guasto Start Vdc Bus 01 Nessuno Cortocircuito Uscita Inverter 14 Vdc Bus Alta 02 Nessuno Tensione Batteria troppo alta 27 BATT FAULT Vdc Bus Bassa 03 Nessuno Tensione Batteria troppo bassa 28 BATT FAULT Vdc Bus Non Bilanciata 04 Nessuno Alta Temperatura 41 Nessuno Guasto Soft Start Inverter 11 Nessuno Sovraccarico 43 OVER LOAD Alta Tensione Inverter 12 Nessuno Guasto Carica Batterie 45 x Bassa Tensione Inverter 13 Nessuno Tabella Fault 9 Interfacce di Comunicazione L UPS dotato delle Interfacce RS232 e USB utilizzabili come porte di comunicazione con un Personal Computer Infatti sul retro sono presenti i connettori delle Interfacce Le Interfacce di Comunicazione RS232 e USB non possono essere attive contemporaneamente Per attivare la comunicazione RS232 e sufficiente collegare solo il cavo RS232 cavo 9 pin diritto pin to pin per attivare la comunicazione USB sufficiente collegare solo il cavo USB I segnali delle Interfacce RS 232 e USB sono tutti isolati tramite foto accoppiatori dalle tensioni pericolose presenti
45. lit Non rispettare queste precauzioni espone l operatore al pericolo di shock elettrico 7 Prima Accensione La procedura di prima accensione molto semplice Si consiglia di seguire con attenzione i punti successivi per una maggiore sicurezza 1 2 Controllare che tutti i dispositivi collegati alle Uscite dell UPS siano spenti Ripristinare la linea elettrica d ingresso all UPS accertarsi della presenza della Tensione di Rete elettrica in Ingresso e controllare che la sua ampiezza e frequenza siano all interno delle specifiche In seguito al punto 2 PUPS accende il display grafico e si pone in uno stato di attesa Stand by durante il quale l UPS non fornisce potenza in Uscita ed attiva solo la funzione di ricarica delle batterie Controllare che il display grafico mostri il flusso di energia della funzione di ricarica batterie Premere il pulsante ON MUTE del pannello frontale per almeno 3 secondi PUPS emette un breve segnale acustico e svolge un SELF TEST di funzionamento Dopo alcuni secondi l UPS comincia a funzionare in modo Normale e il display grafico mostra appunto il percorso del flusso di energia del modo Normale Simulare un black out togliendo la Tensione di Rete elettrica in Ingresso L UPS passa a funzionare nel modo Batteria il display grafico mostra il percorso del flusso di energia del modo Batteria Inoltre ogni 4 secondi emette un breve segnale acustico di allarme Quando l autonomia delle b
46. locali e nazionali in ITALIA le norme CEI per le connessioni d Ingresso Uscita e per il corretto dimensionamento dei cavi d Ingresso Uscita in rapporto alla potenza nominale Il collegamento a terra dell UPS secondo le norme vigenti obbligatorio Rischio di shock elettrico in Uscita se l UPS acceso Rischio di shock elettrico in Uscita se presente la Tensione di Rete elettrica in Ingresso Per rispetto alle norme di sicurezza necessario l inserimento di un interruttore differenziale a valle dell Uscita dell UPS Destinare all UPS una propria linea elettrica di potenza Non ostruire le fessure o i fori di ventilazione e non appoggiare alcun oggetto sopra l UPS Non inserire oggetti o versare liquidi nei fori di ventilazione Installare l UPS in ambiente chiuso pulito e privo di umidit Non esporre l UPS alla luce diretta del sole Non avvicinare liquidi gas infiammabili o sostanze corrosive Manuale utente 24 UPS EVO DSP PLUS MM ITALIANO 1 Introduzione L UPS EVO DSP PLUS MM UPS significa Uninterruptible Power Supply il risultato di una costante ricerca tecnologica mirata all ottenimento delle migliori prestazioni a costi estremamente contenuti EVO DSP PLUS MM un gruppo di continuit monofase ad onda sinusoidale progettato per alimentare e proteggere le pi sofisticate apparecchiature elettroniche infatti fornisce un alimentazione assolutamente continua regolata e priva di disturbi di qu
47. mia Allarme acustico ogni secondo Overload Allarme acustico 2 volte ogni secondo NO Condizioni di Guasto Fault Allarme acustico continuo Modo Bypass Allarme acustico ogni 10 secondi Nota OFF SI indica che l allarme acustico pu essere disattivato premendo il pulsante ON MUTE OFF NO indica che l allarme acustico NON pu essere disattivato 5 2 Pannello Posteriore EVO DSP PLUS MM 1 2 EVO DSP PLUS MM 2 4 EVO DSP PLUS MM 3 6 Figura 4 Pannello Posteriore 1 Interfaccia di Comunicazione connettore femmina DB9 la porta di comunicazione RS232 2 Interfaccia di Comunicazione connettore USB la porta di comunicazione USB 3 Slot per Interfaccia SNMP interface opzionale 4 Presa d Ingresso con TERRA serve per collegare l UPS alla linea elettrica tramite il cavo di alimentazione in dotazione 5 Interruttore Termico d Ingresso Rete l interruttore scatta in caso di sovraccarico o cortocircuito per riarmare l interruttore occorre premere manualmente sulla parte fuoriuscita 6 Prese d Uscita con TERRA di tipo IEC C13 da utilizzare per alimentare carichi critici 7 Morsettiera d uscita per la connessione di una linea di alimentazione d uscita di Potenza per la protezione di tutti i dispositivi Manuale utente 34 UPS EVO DSP PLUS MM ITALIANO 6 Installazione Elettrica L installazione elettrica nonostante la sua semplicit deve essere eseguita esclusivamente da elettricist
48. muta automaticamente dal modo Bypass al modo di funzionamento Normale Controllare che l UPS non indichi mai la condizione di Overload Non applicare all UPS un carico maggiore del valore nominale di targa vedere le specifiche di POTENZA del capitolo Caratteristiche Tecniche in quanto pu esserne danneggiato In tal caso vengono a decadere le condizioni di garanzia 8 4 Bypass Statico Durante il normale funzionamento possibile commutare U UPS in modo Bypass premendo i pulsanti ON MUTE e SELECT contemporaneamente per almeno 5 secondi come spiegato nel capitolo 5 Questa particolare modalit di funzionamento denominata anche Bypass Statico utile quando occorre svolgere operazioni di manutenzione o assistenza sull UPS Infatti il Bypass Statico utilizzato assieme ad un dispositivo di Bypass Manuale esterno permette di isolare completamente i circuiti elettronici dell UPS dalla Rete d Ingresso e dal carico e permette di collegare direttamente la linea d Ingresso al carico in Uscita e fornire potenza al carico per mezzo della linea di Bypass escludendo U UPS senza nessuna interruzione nell erogazione di potenza sul carico AN Manutenzione e assistenza sull UPS devono essere eseguite esclusivamente da personale tecnico qualificato ed autorizzato Se l UPS in Bypass Statico i carichi sono alimentati direttamente dalla linea elettrica d Ingresso tramite il Bypass Quindi non sono attiv
49. nnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded The electric installation has to be done by qualified personnel Follow all the Safety Standards CEI Standards in Italy or IEEE elsewhere for the Input Output connections and for the right section of Input Output cables It is compulsory to ground the UPS according to Safety Standards Risk of electric shock at the Output lines when the UPS is ON Risk of electric shock at the Output lines while the unit is connected to the AC utility line For respect of the Safety Standards is necessary the presence of a differential circuit breaker between UPS Output lines and the loads We recommend to use a dedicate AC power line for the UPS Do not obstruct ventilation slots or holes and do not rest any object on top of the UPS Do not insert objects or pour liquids in the ventilation holes Install the UPS indoors in a protected clean and moisture free environment Do not expose to the direct sun light Do not keep liquids flammable gases or corrosive substances near the UPS A UPS EVO DSP PLUS MM 1 User s manual ENGLISH 1 Introduction The UPS EVO DSP PLUS MM UPS means Uninterruptible Power Supply is the result of constant technological research aimed at obtaining the best performance at the lowest cost EVO DSP PLUS MM is an advanced ON LINE UPS built specifically to protect your computer from any irregularities in the AC line
50. o di umidit polvere e fumo eccessivi Se PUPS deve essere spostato da un luogo freddo ad un luogo pi caldo l umidit dell aria pu causare condensazione all interno dell UPS In tal caso lasciare l UPS nel luogo pi caldo per circa 2 ore prima di cominciare la procedura d installazione Manuale utente 26 UPS EVO DSP PLUS MM ITALIANO Consultare comunque il capitolo Caratteristiche Tecniche per i requisiti ambientali e controllare che il luogo scelto rientri in tali specifiche Durante il normale funzionamento l UPS emette una quantit minima di calore perci necessario lasciare uno spazio libero di almeno 10 cm sia lateralmente che sul retro dell UPS per permetterne una sufficiente areazione Non ostruire le fessure o i fori di ventilazione Non inserire oggetti o versare liquidi nei fori di ventilazione Non appoggiare alcun oggetto sopra UUPS Non avvicinare liquidi gas infiammabili o sostanze corrosive Installare l UPS su superfici piane non inclinate 4 Modi di Funzi BYPASS LINEA INGRESSO FILTRO ger FILTRO INGRESSO RADDRIZZATORE AUTOMAT USCITA CARICA MODO NORMALE BATTERIE LINEA INGRESSO FILTRO A AGIATA FILTRO INGRESSO i USCITA CARICA MODO BATTERIA BATTERIE BYPASS LINEA INGRESSO FILTRO BYPASS FILTRO INGRESSO RADDRIZZATORE hr INVERTER AUTOMAT USCITA I I CARICA BATTERIE MODO BYPASS BATTERIE Figura 1 Modi di Funzionamento UPS EV
51. o la Tensione di Rete viene ripristinata oppure l ampiezza della Tensione rientra all interno delle specifiche PUPS ritorna a funzionare nel modo Normale _ E Il modo Batteria caratterizzato da N e El 4 750 pe Il display grafico LDC mostra il percorso del flusso di 12g io e 30 1 energia durante il modo Batteria e Emissione di un breve segnale acustico ogni 4 secondi 2 8 lim _4 ai A 4 3 Modo BYPASS In modo Bypass la linea di alimentazione d Ingresso viene collegata direttamente all Uscita grazie al blocco Bypass Automatico che seleziona la via di Bypass Come indicato in figura 1 la funzione di ricarica delle batterie garantita anche in questo caso Durante il normale funzionamento l UPS commuta automaticamente nel modo Bypass in caso di sovraccarico accidentale oppure di guasto all Inverter Durante il normale funzionamento possibile commutare l UPS in modo Bypass premendo i pulsanti ON MUTE e SELECT contemporaneamente per almeno 5 secondi come spiegato nel capitolo 5 Manuale utente 28 UPS EVO DSP PLUS MM ITALIANO IL modo Bypass caratterizzato da y e Il display grafico LDC mostra il percorso del flusso di fre esa pee energia durante il modo Bypass gU c3 gt E Emissione di un breve segnale acustico ogni 10 secondi sn gy gt lt a al N In m
52. o nel capitolo 5 TIPO DI ALLARME SIMBOLO lampeggiante ALLARME ACUSTICO Low Battery Fine Autonomia A Allarme acustico ogni secondo Overload AN OVER LOAD Allarme acustico 2 volte ogni secondo Batteria non collegata A BATT FAULT Allarme acustico ogni secondo T Tensione Carica Batteria elevata Allarme acustico ogni secondo AV Inversione di Fase della Tensione A d Ingresso Rete A Allarme acustico ogni secondo VP Guasto Ventole E B A Allarme acustico ogni secondo Alta Temperatura t p A Allarme acustico ogni secondo Guasto Carica Batteria t H AN Allarme acustico ogni secondo Tensione Bypass fuori range Allarme acustico ogni secondo Tabella Allarmi UPS EVO DSP PLUS MM 39 Manuale utente ITALIANO 8 7 Segnalazioni di Guasto Se durante il funzionamento si verifica un Guasto Fault allora UUPS segnala la condizione critica con l emissione dell allarme acustico continuo Inoltre sul display grafico visualizzato il codice di Fault Per maggiori dettagli consultare il capitolo Anomalie ed Interventi In caso di Fault prego controllare i carichi alimentati i collegamenti la ventilazione la linea elettrica d Ingresso le batterie In ogni caso non provare mai a riaccendere l UPS senza aver trovato la causa del guasto Se il problema non pu essere risolto contattare immediatamente il Servizio Assistenza Solo in caso d emergenza per evitare ulteriori r
53. o per accendersi e spegnersi automaticamente a tempi prestabiliti dall utente Leggere attentamente questo manuale prima di utilizzare EVO DSP PLUS MM perch contiene importanti avvisi di sicurezza per l operatore ed utili consigli per un corretto impiego EVO DSP PLUS MM soggetto a continui sviluppi e migliorie di conseguenza pu differire lievemente in alcuni dettagli da quanto descritto nel presente manuale Questo manuale relativo ai seguenti modelli e EVO DSP PLUS MM 1 2 1 2 KVA e EVO DSP PLUS MM 2 4 2 4 KVA e EVO DSP PLUS MM 3 6 3 6 KVA In questo manuale EVO DSP PLUS MM sar chiamato anche semplicemente UPS I modelli EVO DSP PLUS MM sono costituiti da un unit singola che contiene sia l elettronica che le batterie UPS EVO DSP PLUS MM 25 Manuale utente ITALIANO 2 Caratteristiche Generali EVO DSP PLUS MM presenta tutte le moderne caratteristiche che garantiscono massima affidabilita e sicurezza Tecnologia ON LINE doppia conversione senza trasformatore Onda sinusoidale generata tramite Inverter ad IGBT Stabilizzazione in Uscita 2 Protezione dal sovraccarico e dal cortocircuito Bypass Automatico che interviene in seguito a sovraccarico accidentale o a guasto Inverter Accensione anche in condizioni di Assenza Rete Protezione automatica in caso di batterie scariche Riaccensione automatica dopo lo spegnimento per fine autonomia al ritorno della Tensione di Rete Frequenza d Ingres
54. odo Bypass i carichi sono alimentati direttamente dalla linea elettrica d Ingresso tramite il Bypass Quindi non sono attive alcune protezioni contro i disturbi e le interruzioni della linea elettrica 4 4 Modo STAND BY lo stato di UPS disattivo In modo Stand by UPS ha l Inverter disattivo e non fornisce potenza in Uscita l Uscita OFF ma non spento completamente infatti mantiene acceso il display grafico e ricarica regolarmente le batterie L UPS entra in modo Stand by quando si preme il pulsante OFF durante il funzionamento Normale Se PUPS in modo Stand by e si scollega la linea d Ingresso Rete allora PUPS si spegne completamente dopo alcuni secondi Il modo Stand by caratterizzato da nam m ve Tan cay me f Il display grafico LDC mostra il percorso del flusso di energia durante il modo Stand by d 4 5 Modo ECO possibile selezionare il modo ECO per risparmiare energia e aumentare l efficienza dell UPS Il modo ECO utilizza il Bypass per alimentare i carichi L UPS funziona come in modo Bypass finch i parametri della Tensione d Ingresso frequenza forma d onda e valore RMS sono all interno dei limiti accettabili Se la Tensione d Ingresso esce dai limiti accettabili UUPS abbandona la modalit ECO e torna a lavorare normalmente Il modo ECO non abilitato dalla fabbrica Nel caso sia necessario abilitare il modo ECO
55. ond these limits the UPS switches into normal operation Please contact Technical Service for the instruction to enable the ECO mode by default the ECO mode is disable ECO mode does not provide perfect stability in Frequency waveform RMS value of the Output Voltage like in Normal mode Thus the use of this mode should be carefully executed according to the level of protection required by the application u my The ECO mode is identified by n vee m ves eau eau f The graphic LCD panel shows the path of energy flow during ECO mode the ECO icon is ON User s manual 6 UPS EVO DSP PLUS MM ENGLISH 4 6 CONVERTER FREQUENCY Mode It is possible to select the Converter Frequency mode to work with the Output Frequency different from the Input Frequency For example it is possible to work with 60 Hz Input Frequency and 50 Hz Output Frequency or 50Hz Input Frequency and 60 Hz Output Frequency Please contact Technical Service for the instruction to enable the Converter Frequency mode by default Converter Frequency mode is disable and the Output Frequency will synchronize automatically with the Input Frequency by default the Converter Frequency mode is disable r Ey The Converter Frequency mode is identified by L F gag dio e The graphic LCD panel shows the path of energy flow TO f during Converter Freq
56. order to charge Battery completely the UPS charges Battery also in Bypass mode or in Stand by Mode The batteries reach the 90 of their capacity after about 4 hours of recharge UPS EVO DSP PLUS MM 13 User s manual ENGLISH 8 Functioning 8 1 Turning ON and OFF Let s see carefully the consequences of the pressure of ON MUTE and OFF buttons The UPS is in Stand by mode the Inverter is OFF if the ON MUTE button is pressed after few seconds the Inverter starts and the UPS switches in Normal mode The UPS is in Normal mode the Inverter is ON if the OFF button is pressed the Inverter turns OFF and the UPS switches in Stand by mode To turn completely OFF the UPS please do the following steps gt Put the UPS in Stand by mode by pressing the OFF button Disconnect the AC Input Voltage for the UPS The graphic LCD panel is OFF only when the UPS is completely OFF If UPS is used daily it is recommended to leave the UPS connected to the AC Input line and use the ON MUTE and OFF buttons on the front panel to activate deactivate the Inverter If the UPS has to be turn OFF completely for several days it is recommended to disconnect the AC Input line for the UPS and then press the OFF button If the ON button is pressed when AC Input line is not present the UPS switches ON even and works in Battery mode after some seconds If the OFF button is pressed when AC Input line is not present then the Inverter switc
57. re applied Low Voltage Directive Safety EN62040 1 1 2003 EMC Directive Electro Magnetic Compatibility EN62040 2 2006 category C2 WARNING This is a category C2 UPS product In a residential environmental this product may cause radio interference in which case the user may be required to take additional measures Product Disposal UPS EVO DSP PLUS MM cannot be disposed as an urban waste but must be treated as a separate waste Any violation is indictable with financial sanctions as per in force regulations An incorrect waste disposal or an improper use of the same or of any parts can be damaging for the environment and for human health A correct waste disposal of products having the dustbin symbol marked by a cross help to avoid negative consequences to the environment and to human health EE Lead Batteries EVO DSP PLUS MM models contain lead acid sealed maintenance free batteries This kind of batteries if handled by non experienced personnel can cause electric shock or short circuit For this reason the batteries can be removed only by qualified technical personnel specialized and authorized by Tecnoware Tecnoware declines any responsibilities if this rule is not followed To remove the batteries firstly you have to take off UPS cover then remove all the metallic parts that are blocking the batteries pack disconnect batteries one to each other and take them off from their housing one by one
58. rmal lt gt Battery 0 ms Transfer Time Battery Bypass 4 ms typical Efficiency 92 On Line mode 98 ECO mode ph de as 98 BATTERIES Battery Type Lead acid sealed free maintenance Number of batteries 2 4 6 Nominal Battery Voltage 24 Vdc 48 Vdc 72 Vdc Battery Specifications 12 Vdc 9 Ah Backup Time typical 8 min Battery Charge Time typical 4 hours User s manual 18 UPS EVO DSP PLUS MM ENGLISH ENVIRONMENTAL CONDITIONS Storage Temperature Range 25 C to 55 C 15 C to 40 C recommended for longer Battery life Operating Temperature Range 0 C to 40 C 20 C to 25 C recommended for longer Battery life Relative Humidity Range 0 95 non condensing Max Altitude without Derating 3000 m Protection level IP 20 Cooling Fan cooling Audible Noise at 1 meter lt 45 dBA STANDARDS Safety EN 62040 1 1 EN 60950 1 Performance EN 62040 3 EMC EN 62040 2 category C2 Product certification CE COMMUNICATIONS Computer Interface 1 RS232 port and 1 USB port Software Included software compatible with Windows Mac OS X Linux Novell SNMP Interface Optional OTHERS ECO Mode Selectable Frequency Converter Mode Selectable Technical data may change without prior notice UPS EVO DSP PLUS MM 19 User s manual ENGLISH 11 Mainten
59. rtant safety warnings and useful advices for correct use and installation EVO DSP PLUS MM is constantly being developed and improved consequently your unit may differ somewhat from the description contained in this manual This manual includes the following models e EVO DSP PLUS MM 1 2 1 2 KVA e EVO DSP PLUS MM 2 4 2 4 KVA e EVO DSP PLUS MM 3 6 3 6 KVA In this manual EVO DSP PLUS MM will simply be referred to as UPS EVO DSP PLUS MM models are made from a single unit that contains the electronics parts and the batteries User s manual 2 UPS EVO DSP PLUS MM ENGLISH 2 General Characteristics EVO DSP PLUS MM has all the advanced features which guarantee maximum reliability and safety Double Conversion ON LINE Transformerless technology Sinusoidal wave generated by an IGBT Inverter Output Voltage regulation 2 Protection from overload and short circuits Automatic Bypass to protect from accidental overload or Inverter fault Start up even under Mains OFF conditions Automatic protection when Battery is low Automatic restart following an automatic shut down due to Low Battery once AC utility power comes back on Selectable Input Frequency 50 or 60 Hz Graphic LCD panel for visualization of the Input and Output Voltage measurements batteries Voltage percentage of load frequency alarms overload fault and path of energy flow Acoustic signals of various kinds indicating alarm si
60. ry and Automatic Restart cesses 14 8 3 Load Testing A ea eese et rete n d 15 0 4 SAD DASS oss change eae Dawe side a EIER UUECREES NIRE 15 8 5 Battery Test ae t exe ue ENTE IE A deve ens 16 8 6 Operation in Warning Status eee ee eee cece eee ee eee cece enne 16 8 7 Operation in Fault Mode ccc cece cece cence cee rire ee ehe enhn 17 9 Communication Interfaces oooooccccconccnnnccnnocccnnccnocononoccnocconocononos 17 10 Technical Characteristics 6 eee e eee eene rne Eee neue eene pne poen ne rei 18 11 Maintenance Leone reto enr priora 20 1154 UPS Cleaning sore e One Ri De UTE oa 20 11 2 Battery A ali 20 11 3 Operator Safety 1 eee eerte rre e rere ene A 20 12 Tro bleshooting ivi 21 Conformity to the European Directives oooooocococccocccnncocccoccnonccnncononoconos 23 Product Disposal 2 2 0 eee e Tere ee EE ne cavo NA rene c ea era ER 23 Lead Batteries tree ee isla pia Ue leve cates olearia rea napo EVE 23 Manuale Utente Italiano ooooooococccocccnnccnncocococcnonccnncocorocccncconoconoso 24 Indice 1 INEFOAUZIONE EPIIT 25 2 Caratteristiche Generali ooooocccncoccconconnccnnrocaroccconccnorocoroccnonconos 26 3 Ricevimento e Collocazione ooooooocccccocccnnconnroccroccconconococoroccnonconos 26 4 Modi di Funzionamento ccceeeeeeeeeeee eene eene hene het cere coseeeeeese 27 4 1 Modo NORMALE see
61. s 1 The load is still supplied but directly from AC power via Bypass 2 The load is no longer supplied by power Batteries are not fully charged Batteries are defective faulty Fans are locked or not working or the UPS temperature is too high ACTION TO SOLVE Contact Technical Service Remove excessive loads from UPS Output Remove excessive loads from UPS Output Remove excess loads from UPS Output first Then shut down the UPS and restart it Remove excess loads from UPS Output and restart it Check Output wiring or if connected devices are in short circuit status Contact Technical Service Charge the batteries for at least 4 hours and then check capacity If the problem still persists consult Technical Service Contact Technical Service to replace the batteries Check fans and contact Technical Service If the described anomalies should continue despite the advised troubleshooting or should they manifest in any other form please contact User s manual TECNOWARE SERVICE WWW tecnoware com 22 UPS EVO DSP PLUS MM ENGLISH CE Conformity to the European Directives TECNOWARE S r l confirms that EVO DSP PLUS MM models comply with the requirements set out in the Low Voltage Directive Safety 2006 95 EC and following amendments the EMC Electro Magnetic Compatibility Directive 2004 108 EC and following amendments The following standards we
62. s manual ENGLISH wu E The Bypass mode is identified by 4 P Vac Vac The graphic LCD panel shows the path of energy flow nr cU Edi 7 during Bypass mode E S a e An acoustic signal every 10 seconds ve a a P1 gt During Bypass mode loads are fed directly from AC Input line Therefore some protections against AC Input line disturbances or interruptions is present 4 4 STAND BY Mode If the UPS is in Stand by mode it is inactive In Stand by mode the Inverter is off and there is not Output power but the UPS is not completely off indeed the UPS recharges the batteries regularly and the graphic display is ON If the OFF button is pressed when the UPS is in Normal mode the UPS switches in Stand by mode If the UPS is in Stand by mode and the AC Input line is removed from UPS then the UPS switches completely off The Stand by mode is identified by sane m ves aa eau me f e The graphic LCD panel shows the path of energy flow during Stand by mode presi 4 5 ECO Mode It is possible to select the ECO mode to save energy and to increase the efficiency of the UPS The ECO mode uses the Bypass to feed the loads The UPS will operate as in Bypass mode whenever the Frequency waveform RMS value of AC Input line mains Voltage is within their tolerance limits If the AC Input line Voltage goes bey
63. so selezionabile 50 o 60 Hz Display LCD grafico per visualizzazione delle misure della Tensione d Ingresso e d Uscita Tensione batterie percentuale di potenza utilizzata frequenza allarmi guasti e percorso del flusso di energia per i vari modi di funzionamento Segnalazioni acustiche di vario tipo durante il normale funzionamento e che evidenziano le eventuali condizioni di allarme Configurazione e settaggio da parte dell utente dei parametri di funzionamento tramite pannello frontale e display grafico Adattatore SNMP opzionale Comunicazione con il computer tramite interfacce RS 232 e USB Modo di funzionamento ECO selezionabile Modo di funzionamento Convertitore di Frequenza selezionabile Elevato rendimento e basso costo d esercizio Alta affidabilit Curato design e semplicit d uso 3 Ricevimento e Collocazione Al ricevimento dell UPS si consiglia di togliere subito l imballo e di controllare lo stato dell UPS In caso di danni dovuti al trasporto annotarli sulla bolla di accompagnamento merce e contattare subito il fornitore Si consiglia di conservare l imballo originale in luogo sicuro nell eventualit futura che PUPS dovesse essere spedito per la manutenzione Si consiglia di prestare attenzione ai punti seguenti per la scelta di una corretta collocazione dell UPS L UPS progettato per operare in ambienti chiusi come ad esempio gli uffici Si consiglia perci d installarlo in un luogo priv
64. sul display grafico Allarmi ed anomalie che possono verificarsi durante il funzionamento dell UPS sono descritti nella tabella seguente In caso di anomalia nel funzionamento controllare la corretta connessione a TERRA GROUND dell UPS controllare i collegamenti d Ingresso Uscita leggere gli allarmi visualizzati sul display grafico e quindi consultare la tabella sotto riportata Per ogni anomalia svolgere le azioni suggerite Se il problema riscontrato non descritto nella tabella o le azioni consigliate non avessero esito positivo contattare il Servizio Assistenza Rischio di shock elettrico Non smontare l UPS contiene parti sotto tensione che sono potenzialmente pericolose e possono provocare lesioni o morte per shock elettrico L UPS non ha parti interne soggette a manutenzione da parte dell utente Interventi tecnici di qualsiasi tipo devono essere compiuti solo da personale tecnico specializzato ed autorizzato da TECNOWARE In caso contrario TECNOWARE declina ogni sua responsabilit ANOMALIA POSSIBILE CAUSA AZIONI PER RISOLVERE Nessuna segnalazione sul pannello frontale anche se presente la Tensione di Rete in Ingresso Il display grafico spento simboli A e we lampeggiano sul display grafico e l allarme acustico suona ogni secondo simboli A e lampeggiano sul display grafico e l allarme acustico suona ogni secondo Sul display grafico visualizzato il codice
65. te operation Indicates that the UPS alarm is disabled muted Output Voltage information Cc Cc Ci Vac OOO nz OUTPUT Indicates the Output Voltage or Frequency Vac Output Voltage Hz Output Frequency Load information Q Indicates the load level by 0 25 26 50 51 75 and 76 100 _l OVER LOAD Indicates Overload SHORT Indicates the load or the Output is short circuited Programmable Output information Indicates that there is an active scheduling for the programmable Output Mode operation information Indicates the UPS connects to the mains Indicates the Battery is working BYPASS Indicates the Bypass circuit is working EG 0 Indicates the ECO mode is enabled il Indicates the Inverter circuit is working 0 3 Indicates the Output is working UPS EVO DSP PLUS MM 9 User s manual ENGLISH Graphic LCD Panel Function Battery information Th ih Indicates the Battery capacity by 0 25 26 50 51 75 and 76 100 Indicates the Battery is faulty or defective Indicates Low Battery level and Low Battery Voltage Input and Battery Voltage information O ce c Vac OO te INPUT Indicates the Input Voltage or Frequency or Battery Voltage Vac Input Voltage Vdc Battery Voltage Hz Input Frequency 5 1 2 Buttons Functions of the buttons are gi
66. tuations Available settings of all the UPS parameters by user through front panel pushbuttons and graphic LCD panel SNMP Adapter optional Communication with the computer through RS 232 and USB interfaces ECO functioning mode selectable Frequency Converter functioning mode selectable High efficiency Maximum reliability Smart design and easy to use 3 Receipt and site selection Carefully remove the UPS from its packaging and carry out a meticulous inspection We recommend keeping the original packaging in a secure place in case you need to send the UPS for maintenance purposes In case of transport damage notify the carrier and dealer immediately We recommend paying attention to the below points in order to choose a correct placement for your UPS The UPS is designed to operate in a protected environment e g offices We therefore recommend installing it in a place with very little or no humidity dust or smoke When the UPS is brought from a cold place to a warmer place humidity in the air may cause condensation in the UPS In this case allow UPS to stand for two hours in the warmer place before beginning with the installation UPS EVO DSP PLUS MM 3 User s manual ENGLISH In all circumstances see the Technical Characteristics chapter for environmental specifications and check that the selected area meets these criteria During normal operation the UPS discharges a minimal amount of
67. uency mode e The CF characters are ON CA 8 i c s 3 IS 5 EXTERNAL DESCRIPTION 5 1 Front Panel The front panel informs the user about operating status alarm conditions and measurements lt also provides access to controls and configuration parameters Front panel shown below consists of two parts 1 Graphic LCD panel provides complete information about the energy flow path and existing alarms Load and Battery level Input Output and Battery measurements 2 3 buttons enables the user to turn ON OFF the UPS and to make selections of the functioning parameters m rec mnl ON MUTE SELECT UPS EVO DSP PLUS MM 7 User s manual ENGLISH Figure 2 Front panel 5 1 1 Graphic LCD Panel Please refer to figure 3 Input amp Battery Backup Time 1 Output Voltage Info n Info Fault Info Buzzer Info Voltage Info A A A o L UN cepe o Mp TERESA Battery Mode Operation Programmable Info Output Info Figure 3 Graphic LCD Panel User s manual 8 UPS EVO DSP PLUS MM ENGLISH Graphic LCD Panel Function Backup time information H mu CD Lia Oro Indicates how much time has passed in Battery mode H hours M minutes S seconds Fault information Indicates the warning that a fault has occurred Indicates the Fault codes and the codes are listed in the Fault Table of chapter 8 Mu
68. ve your problem consult the Technical Service Risk of electric shock do not remove the cover The UPS contains internal parts which are at a high Voltage and are potentially dangerous capable of causing injury or death by electric shock There are no internal parts in the UPS which are user serviceable Any repair or maintenance work must be performed exclusively by qualified technical personnel authorized by TECNOWARE TECNOWARE declines any responsibility if this warning is disregarded SYMPTOM POSSIBLE CAUSE ACTION TO SOLVE Check if the Input cable is firmly connected to the AC Input mains and to the AC Input socket of The Input cable is not connected well to the AC Input mains or to the No indication and or alarm on the AC Input socket of UPS UPS front panel even though the main is normal The graphic display is OFF Check the Input Circuit Breaker if it is OFF push the external button of the Input Circuit Breaker to reactivate it The Input Circuit Breaker is OFF A Disconnect the Input Cable from The icons and we flash on the Line and Neutral poles of AC input AC Input mains socket rotate graphic display and alarm beeps Line are reversed the plug by 180 and then every second connect again The icons A and flash on The external or internal batteries Check if all batteries are LCD display and alarm beeps every are incorrectly connected connected correctly second
69. ven below Button Function ON MUTE Turn ON the UPS press and hold ON MUTE button for at least 3 seconds to turn ON the UPS Mute the acoustic alarm when the UPS is in Battery mode press and hold this button for at least 5 seconds to disable or enable the acoustic alarm But it s not applied to the situations when warnings or errors occur Test Battery press and hold ON MUTE button for at least 5 seconds to perform the Battery Test while the UPS is in Normal mode SELECT Select the measurements on the graphic display by pressing the SELECT button it is possible to choose the electrical parameter to be displayed Input Voltage Input Frequency Battery Voltage Output Voltage Output Frequency If the button is not pressed for at least 10 seconds then the default parameter will came back on the graphic display the default parameters are Input Voltage and Output Voltage OFF Turn OFF the UPS press and hold ON MUTE button for at least 3 seconds to turn OFF the UPS By pressing this button while the UPS is in Normal mode the UPS will go to Stand by mode by pressing this button while the UPS is in Battery mode the UPS will switch OFF completely ON MUTE SELECT Switch to Bypass mode when the UPS is functioning in Normal Mode press ON MUTE and SELECT buttons simultaneously for at least 5 seconds Then UPS will enter to Bypass mode This action will be ineffective when the Input voltage is out o
Download Pdf Manuals
Related Search
Related Contents
Sobre a bateria Océ TCS500 User Manual Samsung SGH-U600B Kasutusjuhend Mode d`emploi Bio Dentaplast DELL Inspiron 3646 HOJA DE SEGURIDAD FICHA TCNICA Copyright © All rights reserved.
Failed to retrieve file