Siemens WD14H421GB washer dryer
Contents
1. Check the alignment of the washer dryer with a spirit level and if required correct Adjust the height by rotating the appliance foot Note All four appliance feet must be firmly on the floor The washer dryer must not wobble Tighten the lock nut against the housing Grip the foot and do not adjust the height Notes 42 The lock nuts on all four appliance feet must be screwed tightly against the housing Any loud noises intense vibrations or wandering may be due to incorrect alignment Electrical connection Electrical safety Z Warning Risk of electric shock Danger of death if live parts are touched When disconnecting the main plug always pull the plug itself and not the cable otherwise the cable could be damaged Never touch or hold the mains plug with wet hands Never pull out the mains plug during operation Only connect the washer dryer to an alternating current using a correctly installed earthed socket The mains voltage must be the same as the voltage specifications on the washer dryer appliance rating plate The connected load and the required fuse are also indicated on the appliance rating plate Ensure that The mains plug and socket match The cable cross section is adequate The earthing system has been installed correctly A damaged power cord is only replaced by an electrician A replacement mains cable can be obtained from customer service You do not use2. Tighten screw fitting on the supply hose Start Reload not selected Tap not open Filter blocked Clean the filter gt Page 29 supply hose kinked or jammed Safety function active Stop programme w Rinse stop without final drain spin selected Can be opened with emergency lock release only gt Page 30 Childproof lock active Deactivate gt Page 17 Start Reload or Finish in selected Door closed Rinse stop without final drain spin selected Clean the drain pump gt Page 28 Clean outlet pipe and or drainage hose Not a fault water below the visible area Not a fault unbalanced load detection system has stopped the spin cycle washing unevenly distributed Distribute small and large items of washing in the drum Too low speed selected Not a fault unbalanced load detection system adjusts imbalance Not a fault effect of the care product not impaired If required remove the insert Clean the detergent drawer and re insert it Remove the insert Clean the detergent drawer and reinsert it Run the Fluff Clean 90 C programme without laundry Use standard detergent Too much detergent used Mix 1 tablespoon of fabric softener with litre of water and pour into dispenser Il Not for outdoor sports and down filled textiles Reduce detergent dosage for the next wash cycle Use commercially available low foam detergent and care products which are suitable for washer dryers Ap
3. 3 Pull down emergency release with a tool and release Door can then be opened Faults and what to do about them en Information on the display panel DEEN Cause Remedy A 01 Close the door immediately because of the rising water level If an interruption occurs A 01 and OPEn are displayed alternately A 02 The door is locked for safety reasons water level and or temperature too high Washing programme In pause mode A 02 and PAUS are displayed alter nately If you have to open the door wait until the temperature has dropped slightly or pump out the water select e g Spin or Drain Drying programme If you have to open the door wait until the temperature has dropped slightly or set the drying programme to 15 min to cool down the laundry If A 02 is frequently displayed at the end of the drying programme m Clean the air filter gt Page 30 m Run the Fluff Clean cold programme without laundry A 03 Door cannot be locked unlocked due to high temperature Leave the washer dryer Switched on for about 1 min The washer dryer can then be locked unlocked again hot The door cannot be opened after the drying programme due to the high tempera ture The cooling process continues until the display disappears after which the door can be opened a m Flashes no water supply Tap turned on Water inlet filter blocked Clean the water inlet filter gt Page 29 Water hose kinked or blocked m Lights up low water pr
4. The main points in brief N Plug into the mains Open the washer Select the washing Max load in display Turn the tap on dryer door drying programme panel Temp Spinrpm Option Select Finish in 2 If required change the programme default Sort the laundry Load the laundry settings and or select additional functions D D gt Open the detergent Dose detergent Close the washer select Start Reload drawer according to the dryer door dosing recommendation Page 16 D gt End of the set programme Open the door and Turn off the water programme selecter to O Off remove the laundry tap for models without Aqua Stop N en Getting to Know your appliance Getting to know your appliance Washer dryer Hot air outlet Open the door Operating display panel Close the door 7 Door with handle Service flap and cool air inlet Getting to Know your appliance en Control panel Off O Intensive Dry Cottons Gentle Dry Easy Care Refresh Mixed Fabrics Fluff Clean n iy Delicates Silk Textile Guard M Wool Shirts Business Rinse Temp Spinrpm Option Select ee 60 Drain apin wash amp dry 7 4 kg Change the default settings for the selected Select buttons Option and Select for programme and select additional functions additional functions gt Page 26 Ea Start programme Select the Start Reload Select a programme Can be r
5. a lf a drying programme was interrupted the washer dryer and laundry may be very hot select Intensive Dry or Gentle Dry and select 15 min drying time to cool down the washing and then remove Safety for children A Warning Danger of death If children play on the washer dryer they may place themselves in life threatening situations or injure themselves m Do not leave children unsupervised near the washer dryer m Do not let children play with the washer dryer Z Warning Danger of death Children may lock themselves inside appliances and suffocate On redundant appliances Pull out the mains plug m Sever the power cord and discard together with the plug a Destroy the lock on the door of the washer dryer en Protection of the environment Z Warning Risk of choking When playing children may become entangled in the packaging Tilm and packaging parts or pull them over their heads and suffocate Keep packaging plastic film and packaging parts out of the reach of children A Warning Risk of poisoning Detergents and care products may be poisonous if consumed Keep detergents and care products out of the reach of children Z Warning Eye skin irritation Detergents and care products may cause Irritation if they come into contact with the eyes or skin Keep detergents and care oroducts out of the reach of children Z Warning Risk of injury When washing at high temperatur
6. and connection en Transportation Preparatory work 1 Turn off the tap 2 Release the water pressure in the Supply hose Filter in the water inlet hose blocked Page 29 3 Drain any residual washing water Drain pump blocked Page 28 4 Disconnect the washer dryer from the power supply 5 Remove the hoses Installing transportation protection devices 1 Remove the covers and keep in a Safe place lf required use a screwdriver 2 Insert all 4 sleeves Clamp the mains cable on the holders Insert and tighten the bolts Before switching on the appliance Notes Always remove the transportation orotection devices m o prevent unused detergent from flowing into the outlet during the next wash Pour 1 litre of water into dispenser Il and start the Spin or Drain programme 43 LT LIL 9000907639 9503
7. in the drum is caused by the final inspection Secure installation Warning Risk of injury m Ihe washer dryer is heavy Take care when lifting it m When lifting the washer dryer by its projecting parts e g washer dryer door the parts may break off and Cause injuries Do not lift the washer dryer by its projecting parts m lf the hoses and power cables are installed incorrectly there is a risk of stumbling and injury Lay hoses and cables in such a way that there is no risk of stumbling Caution Damage to the appliance m Frozen hoses may tear or burst Do not install the washer dryer outdoors and or in an area where there is a risk of frost m When lifting the washer dryer by its projecting parts e g washer dryer door the parts may break off and Cause injuries Do not lift the washer dryer by its projecting parts 37 en Installation and connection Installation area Note Stability is important to prevent the washer dryer from wandering The installation area must be firm and level m soft floors and floor coverings are not suitable m o ensure good drying results ensure that the room is well ventilated Installing the appliance on a base or on a wooden joist ceiling Caution Damage to the appliance The washer dryer may wander during the spin cycle and topple or fall off its base Always secure the washer dryer feet with holding brackets Holding brackets order no WMZ
8. is rotating the door remains locked for safety reasons and reloading is not possible lf the following is indicated on the display panel A 02 PAUS Reloading is not possible To continue the programme select the Start Reload button OPEn are lit Reloading is possible m Do not open the door until both the symbols OPEn are lit Do not leave door open for a prolonged period water could run out of the laundry m The reloading function cannot be activated during the drying phase Changing the programme If you have started the wrong programme by mistake you can change the programme as follows 1 Select Start Reload 2 Select another programme If required adjust the default settings and or select additional functions 3 Select Start Reload The new programme starts from the beginning Interrupting or ending the programme For programmes at high temperature 1 Select Start Reload 18 2 ITO cool down laundry select Rinse 3 Select Start Reload For programmes at low temperature 1 Select Start Reload 2 Select Spin or Drain 3 Select Start Reload For drying programmes 1 Select Intensive Dry or Gentle Dry 2 Touch button Dry and set drying time to 15 minutes 3 Select Start Reload End of the programme 0 or Rinse stop without final drain spin cycle is indicated in the display and acoustic signal sounds Setting the signal gt Page 2
9. not be treated with fabric softener Liquid starch can be used in all wash programmes Pour starch into the dispenser amp according to manufacturer s specifications if required clean beforehand Dyeing Bleaching Dye in household quantities only Salt may attack stainless steel Observe specifications of the dye manufacturer Do not bleach laundry in the washer dryer Soaking 1 Pour soaking agent detergent into dispenser Il according to the manufacturer s instructions 2 Set the programme selector to Cottons 60 C and select Start Reload 3 After approximately 10 minutes select Start Reload 4 After the required soaking time reselect Start Reload if the programme is to be continued or change the programme Note Load laundry of the same colour No additional detergent is required the soaking solution is used for washing 24 Changing programme default settings You can change the default settings for selected programmes The settings can be changed even while the selected programme Is running The effects depend on the progress of the programme Temp Spinrpm Option Select Temp L1 The indicated washing temperature can be changed The maximum selectable washing temperature varies depending on the selected programme Overview of programmes Page 20 Spin rpm 2 The spin speed can be changed before and during the programme in rom revolutions per minute
10. water drainage hoses are under high pressure To prevent leakage or water damage always follow the instructions in this chapter Notes 40 In addition to the safety information listed here the local water and electricity supplier may have special requirements Operate the washer dryer with cold drinking water only Do not connect the washer dryer to the mixer tap of an unpressurised hot water boiler Use only the inlet hose supplied or one purchased from an authorised specialist outlet Never use an used one If in doubt have the appliance connected by a technician Water supply Notes Do not kink crush alter or cut through the water supply hose otherwise its strength can no longer be guaranteed Only tighten the screw connections by hand If the screw connections are tightened too tightly using a tool pliers the threads may be damaged Optimum water pressure in the mains 100 1000 kPa 1 10 bar When the tap is turned on the water flow is at least 8 I min If the water pressure Is higher install a pressure reducing valve Connect the water supply hose to the tap 34 26 4 mm and to the appliance except models with Aquastop Standard 2 Carefully turn on the tap and check that the connection points are not leaking Note The screw connection is under water pipe pressure Water drainage Notes Do not kink or overextend t
11. 2200 WX 9756 CZ 110600 Z 080X0 Note If installing on a wooden joist ceiling f possible install the washer dryer in a corner m Screw water resistant wooden board min 30 mm thick to the floor Installing the appliance under between kitchen units Warning Risk of electric shock Danger of death if live parts are touched Do not remove the appliance cover Build under build in before connection to the power supply 38 Z Warning Risk of scalding During the drying phase warm air is emitted at a temperature of up to 60 C Notes m Required dimensions a 650 mm b 620 mm c 850 mm Only install the washer dryer under a continuous worktop connected firmly to the adjacent cupboards Ventilate the installation area well otherwise the optimum drying results will not be achieved Dimensions of the ventilation openings to be provided on one side depending on the circumstances Opening cross section d x e 200 mm x 100 mm Height above floor f 365 mm Distance between wall and appliance 50 mm Removing the transportation protection devices Caution Damage to the appliance Before using the washer dryer for the first time it is essential to remove all 4 transportation protection devices Keep the transportation protection devices The washer dryer is secured for transportation with transportation protection devices Transportation p
12. 7 If w Rinse stop without final drain spin cycle was selected press Start Reload button to start the final drain spin cycle Notes m The programme continues by pumping out the water and spinning the laundry the standard spin speed can be changed beforehand m f only the water is to be pumped out approx 1 minute after the programme starts touch the Start Reload button before the spin cycle starts then turn the programme selector to O Off The programme is interrupted and the door lock Is released The laundry can be removed lf hot flashes in the display before the drying programme ends the temperature in the drum is high The programme for cooling the drum runs until the temperature in the drum has dropped Operating the appliance en After washing drying 1 Open the door and remove the laundry 2 Turn the programme selector to Off The appliance is switched off 3 Turn off the tap Not required for Aqua Stop models Page 37 Notes Do not leave any items of laundry in the drum In the next wash they may shrink or discolour another item m Remove any foreign objects from the drum and the rubber seal risk of rust m Leave the detergent drawer and door open so that residual water can evaporate m Always remove the laundry Always wait until the programme ends as the appliance could still be locked Then switch the appliance on and wait for the unlocki
13. SIEMENS Washer dryer WD14H421GB siemens home com welcome en Instruction Manual and Installation Instructions Register your product online Your new washer dryer You have chosen a Siemens washer dryer Please take a few minutes to read and become familiar with the advantages of your washer dryer To meet the high quality demands required by Siemens every washer dryer that leaves our factory is carefully checked to ensure that it functions correctly and is in perfect condition For more information on our products accessories replacement parts and services see our website www siemens home com or contact our after sales service centres lf the operating and installation instructions describe different models any differences will be pointed out at the relevant points in the text L Read these operating and installation instructions before switching on the washer dryer Display rules A Warning This combination of symbol and signal word indicates a possibly dangerous situation Not heeding the warning can cause death or injuries Caution This signal word indicates a possibly dangerous situation Not heeding the caution can cause property and or environmental damage Note tip Information about the optimum use of the appliance any other useful information 1 2 3 a b c The steps are represented by numbers or letters a Lists are represented by a small box
14. Touch Select button to select this additional function v indicator light of SpeedPerfect function comes on To deselect the function touch the Select button agian and the Y indicator light goes off Option Select Note After changing the programme default settings and or additional functions the programme duration may change Operating the appliance en Adjusting the drying programme Note If an individual drying programme or washing and drying without interruption is selected you can change the default settings for the drying programme if required Overview of programmes Page 20 Changing the default settings for a drying programme Touch the Dry button to set the desired drying mode or drying time only for an individual drying programme Note After changing the default settings for the drying programme the programme duration may change Loading the laundry Z Warning Danger of death Laundry items pretreated with solvent based detergents e g stain remover petroleum ether may cause an explosion if loaded into the washer dryer Thoroughly rinse laundry items by hand before washing Notes Mix large and small items Laundry items of different sizes distribute themselves better during the spin cycle Individual laundry items may cause an unbalanced load 15 en Operating the appliance m Observe the indicated maximum load Overfilling adverse
15. al 1 Activate setting mode for the signal volume rRe Turn to Off Turn one position Press and hold Temp button Release the button clockwise turn one position clockwise figure apperas in the display 2 a Set the volume for the button signals depending on model Touch the Finish in button until Go to step 2 b or Setto Off swhich exits setting mode the required volume is reached for the signal volume 2 b Selecting the volume for the information signals Turn one position clockwise Touch the Finishin Set to Off which exits setting button until the mode for the signal volume required volume is reached of en Cleaning and maintenance Cleaning and maintenance Warning Risk of electric shock Danger of death if live parts are touched Switch off the appliance and disconnect at the mains plug Z Warning Risk of poisoning solvent based cleaning agents e g petroleum ether in the washer dryer may cause toxic vapours Do not use solvent based cleaning agents Caution Damage to the appliance solvent based cleaning agents e g petroleum ether may damage the Surfaces and components of the washer dryer Do not use solvent based cleaning agents Machine housing Control panel Immediately remove washing and cleaning agent residue Wipe with a soft damp cloth Do not use abrasive cloths soonges or detergents stainless s
16. ater There symbol flashes during the fore the tap must be turned on even during the drying phase drying phase Drying duration extended m According to the air cooling principle a higher ambient temperature will result in poor drying performance so the drying time will be extended Ensure good ventilation to allow surplus heat to escape m Air filter blocked Clean the air filter gt Page 30 Run the Fluff Clean cold programme to remove fluff which has col lected in the washer drum during the drying phase Drying programme does Drying programme not selected Overview of programmes gt Page 20 not start Door not closed properly m Pump blocked Clean the drain pump gt Page 28 33 en Faults and what to do about them Faults Cause Remedy The drying result isnot m satisfactory laundry is not dry enough When the door is opened m you will notice that a small amount of water drips onto the dried laundry a Excessively high ambient temperature above 30 C or inadequate venti lation in the room in which the washer dryer is situated Ensure adequate ventilation to allow surplus heat to escape The laundry has not been spun well enough before drying Always set the highest selectable spin speed for the particular washing programme Washer dryer overloaded Observe the recommendations for the maxi mum load in the programme table and on the load display Do not overload the washer dryer as the maxim
17. depending on the progress of the programme setting w Rinse stop without final drain spin cycle laundry remains in the water after the last rinse cycle The maximum spin speed depends on the programme and model Overview of programmes Page 20 Dry L3 The drying function can be activated deactivated and set with this button Washing and drying without interruption is possible in automatic mode only If the programme for individual drying is selected automatic Changing programme default settings en drying or timed drying with a required drying duration is available Notes m Programme selection in Intensive Dry or Gentle Dry position to select an individual drying programme Overview of programmes Page 20 The standard drying mode is Autt1 In this mode the drying time is automatically set according to the amount of laundry to be dried The result is Cupboard dry laundry Drying mode can be set to Aut2 in order to obtain an extra dry result or oreselect the drying time which can be specified by selecting the Dry button Cupboard dry Aut1 For single layer fabrics Garments can be folded or hung up in a cupboard Extra dry Aut2 For fabrics made of thick multilayered items of clothing which need to be dried longer Garments can be folded or hung up in a cupboard Laundry more dry than Cupboard dry m Programme selection in washing programmes and if washing and drying is required without interrupti
18. e fabrics made of wool or wool blend particularly gentle wash programme to prevent shrinkage of laun dry with longer programme breaks soaking garments in the deter gent solution Note m Wool is of animal origin e g Angora alpaca llama sheep m Use a detergent suitable for machine washable wool Rinse Washable textiles Extra rinse with spin Spin Extra spin with selectable spin speed Drain Draining of the water inside the drum e g after rinse stop w Rapid 15 Wash amp Dry 60 For small amount lt 1kg lightly soiled garments made of cotton linen synthetic or blended fabrics Approx 15 mins for washing If drying function is selected it s followed by another approx 45 mins drying process Note Reduced load for additional function Shirts Business suitable for Shirts Blouses made of cotton linen synthetics fibres or blended fabrics max 2 kg cold 40 C w 800 rpm max kg w 1400 rom 5 5 2 max kg 400 1400 rom A max kg max 3 9 2 kg 1 kg cold 40 C u 1000 rom HW a Aut 1 max 2 0 kg 2 0 kg cold 60 C w 800 rpm 25 6 4 5 2 4 Aut 1 Aut 2 21 en Overview of programmes Programme Type of washing Options Information Textile Guard max 1 kg 1 kg Weatherproof and outdoor clothing with membrane coating and cold 40 C water resistant textiles 400 800 rpm 25 8 4 Aut 1 Fluff Clean Special pro
19. e the washer dryer in a room which has an outflow Before operating the appliance Read the installation and operating instructions and all other information enclosed with the washer dryer and use the machine accordingly Retain documents for subsequent use Safety instructions Electrical safety Z Warning Danger of death Danger of death if live parts are touched a When disconnecting the mains plug always pull the plug itself and not the cable otherwise the cable could be damaged Never touch or hold the mains plug with wet hands Risk of injury Z Warning Risk of injury a lf the washer dryer is lifted using projecting parts e g the washer dryer door these components may break off and Cause injuries Do not lift the washer dryer by its projecting parts a f you climb onto the washer dryer the worktop may break and cause injuries Do not climb onto the washer dryer a f you lean support yourself on the open door the washer dryer may overturn and cause injuries Do not lean on the open washer dryer door a If you reach into the rotating drum you may injure your hands Do not reach into the rotating drum Wait until the drum stops rotating Safety instructions en A Warning Risk of scalding a When washing at high temperatures you may be scalded if you touch the hot washing water e g if draining hot washing water into a washbasin Do not touch the hot washing water
20. e water tap Clean the filter with a small brush i i PS SS iS 6 Clean the filter on the back of the appliance Remove the hose from the rear of the appliance 29 en Faults and what to do about them Take out the filter with pliers and Clean it 7 Connect the hose and check for leaks Air filter blocked 1 Turn the programme selector to O Off Pull out the mains plug 2 Open and remove the service flap 3 Take out the air filter 4 Rinse fluff off the air filter using a brush under running water 5 Re insert the air filter 6 Re insert and close the service flap 30 Faults and what to do about them Emergency release e g ifa power failure occurs The programme continues running when the power supply is restored If the laundry is still to be removed the door can be opened as described below Z Warning Risk of scalding When washing at high temperatures you may be scalded if you touch hot washing water or the laundry If required leave to cool down Z Warning Risk of injury If you reach into the rotating drum you may injure your hands Do not reach into the rotating drum Wait until the drum stops rotating Caution Water damage Leaking water may cause damage Do not open the door if you can still see water through the glass 1 Turn the programme selector to Off Pull out the mains plug 2 Drain the detergent solution
21. es the glass part of the door becomes hot Prevent children from touching the hot door Protection of the environment Packaging old appliance H Dispose of packaging in an environmentally friendly manner This appliance has been identified in accordance with the European Directive 2012 19 EU on Waste Electrical and Electronic Equipment WEEE The Directive specifies the framework for an EU wide valid return and recycling of waste appliances Hints and tips m Utilise the maximum amount of washing for the particular programme Overview of programmes Page 20 m Wash normally soiled laundry without orewash Energy saving mode he display panel light goes out after several minutes Start Reload flashes To reactivate the display select any button The energy saving mode is not activated if a programme is running m he selectable temperatures apply to the care labels on the textiles The temperatures in the machine may deviate from this so that you get the optimum mix of energy saving and washing results m If the laundry is then dried in the appliance select the maximal possible spin speed The less water the laundry contains the less time and energy are required for drying Do not dry dripping wet laundry Ventilate the installation room well and clean the air inlet filter regularly Cleaning and maintenance Page 28 and installation and connection Page 37 The main points in brief en
22. essure For information only This will not affect the programme progress The programme duration is extended E 18 Drain pump blocked clean the drain pump Clean the drainage hose on the siphon Sines Hold down button Dry for 3 seconds to delete the display m Clean the air filter gt Page 30 m Run the Fluff Clean cold programme without laundry LO kg HI kg Laundry amount information On when drying phase finished LO kg Signals a small load for drying HI kg Signals a very high load for drying Other displays Turn the programme selector to O Off The appliance is switched off Wait 5 s and switch on again If the display is indicated again call customer service 31 en Faults and what to do about them Faults and what to do about them Faults Cause Remedy Water is running out Water not flowing in Detergent not dispensed The washing machine door cannot be opened Programme does not start Detergent solution is not drained Water not visible in the drum Spin result not satisfac tory Laundry wet too damp Spin cycle activated sev eral times Residual water in the dis penser for care product Compartment amp is not rinsed out completely Odour formation in the washer dryer Status display is on Foam may come out of the detergent drawer Excessive noise vibra tions and wandering during the spin cycle 32 Correctly attach replace drainage hose
23. from the surfaces of the washer dryer Using a damp cloth immediately remove any fine spray residue and other residue or droplets Empty any pockets Remove any foreign objects m Remove metal parts paper clips etc m Trousers Knitwear and knitted textiles e g jersey garments T shirts or sweatshirts should be turned inside out m Ensure that underwired bras are machine washable m Wash delicates in a net or bag tights underwired bras etc Close zips button up covers m Brush sand out of pockets and collars m Remove curtain fittings or include in the net bag Preparing laundry for drying Note To ensure an even drying result sort the laundry according to the ype of fabric m Drying programme Care symbols which are indicated on the care labels Only dry laundry which is labelled dryer proof or which has the following care symbols Dry at normal temperature Intensive Dry a Dry at low temperature Gentle Dry The following textiles must not be dried m J care symbol Do not dry Wool or textiles containing wool m Delicates silk synthetic curtains Textiles which contain foam rubber or similar materials Textiles which were treated with flammable liquids e g with stain remover petroleum ether thinners Risk of explosion Textiles which still contain hairspray or similar substances Notes Before drying hand washed textiles must be s
24. gram for drum hygiene or fluff removal cold 40 90 C 90 C antibacterial program do not use detergent 400 1400 rpm 40 C antibacterial program special drum cleaning detergent can be used cold rinsing programme for the removal of fluff which has col lected in the washer drum during the drying phase Refresh max 1 kg Odour removal and wrinkle reduction program suitable for wool linen suits etc which do not need frequent washing Gentle Dry max 2 0 kg single gentle dry programme for drying garments with lower tem perature by selecting Aut to achieve automatic cupboard dry result by selecting Aut2 to achieve automatic extra dry result a self defined drying time selectable from 30 60 90 to 120 mins Aut 1 Aut 2 Time dry Note 15 min drying time is for cooling down the laundry and machine after drying process Intensive Dry max 4 kg Single normal dry program for drying garments with higher tempera ture by selecting Aut to achieve automatic cupboard dry result by selecting Aut2 to achieve automatic extra dry result T self defined drying time selectable from 30 60 90 to 120 mins Aut 1 Aut 2 Time dry Note 15 min drying time is for cooling down the laundry and machine after drying process 22 Overview of programmes en Drying table Cottons coloureds textiles made of cotton or linen such as underwear T shirts sweaters trousers kitchen
25. he water drainage hose Height difference between the placement area and drainage point Minimum 60 cm maximum 100 cm Drainage into a wash basin Z Warning Risk of scalding When washing at high temperatures you may be scalded if you touch the hot washing water e g if draining hot washing water into a washbasin Do not touch the hot washing water Caution Water damage If the attached drainage hose slips out of the washbasin due to high water pressure when draining the appliance leaking water may cause damage Secure the drainage hose to prevent it from slipping out of the washbasin Caution Damage to appliance textiles If the end of the drainage hose is immersed in the drained water water may be drawn back into the appliance Installation and connection en and damage the washer dryer and or textiles Ensure that the sealing plug does not block the outflow of the washbasin m the water drains quickly enough m the end of the drainage hose is not immersed in the drained water Installing the drainage hose ZX Drainage into a siphon The connection point must be secured with a 24 40 mm hose clip specialist store Connecting Drainage into a plastic pipe with rubber sleeve or into a gully Connecting 4 en Installation and connection Alignment 1 2 Loosen the lock nut in a clockwise direction with a wrench
26. liance Note If you have activated the childproof lock you must deactivate it before you can set a programme m select the required programme with the programme selector Can be rotated in either direction The washer dryer is switched on The following figures are indicated continuously on the display panel for the selected programme the programme duration the preset temperature the preset spin speed and the maximum load Adjusting the washing programme You can use the displayed default settings or adjust the selected programme optimally to the laundry items by changing the default settings or selecting additional functions The selectable settings and additional functions depend on the selected washing drying programme Overview of programmes Page 20 Notes m Options can be selected deselected or changed depending on the progress of the programme Ihe buttons are sensitive they only need to be touched gently If the button Temp Temperature Spin rpm Spin speed Finish in is held down the setting options are automatically scrolled through Changing default settings for a washing programme e g washing temperature Touch the Temp Temperature button to set desired washing temperature Changing the additional functions for a washing programme e g select SpeedPerfect 1 Touch the Option button until the SpeedPerfect indicator light comes on 2
27. ly select the childproot lock The display panel shows the Finished in time while the programme Is running or the programme duration and the programme progress symbols when the washing programme has started Display panel Page 10 Childproof lock You can secure the washer dryer to prevent the set functions from being changed inadvertently To do this activate the childproof lock when the programme has started Activating deactivating Touch and hold the button Finish in for approx 5 s The symbol gt is indicated in the display If the button signal is activated an acoustic signal sounds m lights up The childproof lock is activated m flashes The childprooft lock Is active and the programme selector has been adjusted To prevent the programme from terminating reset the programme selector to the initial programme The symbol lights up again Note The childproof lock may remain activated until the next programme starts even after the washer dryer has been switched off If this is the case deactivate the childproof lock before the programme starts and if required re activate after the programme starts 17 en Operating the appliance Reloading the laundry When the programme has started the laundry can be reloaded or taken out as required Select Start Reload The washer dryer checks whether reloading is possible Notes m If there is a high water level high temperature or if the drum
28. ly affects the washing result and promotes creasing 1 Unfold presorted laundry items and place in the drum 2 Ensure that no laundry items are trapped between the door and rubber seal 3 Close the door Note The indicator light on the Start Reload button flashes and the default settings for the programme appear continuously on the display panel Changes may be made to the default settings Dosing and adding detergent and care product Caution Damage to the appliance Detergents and agents for the pretreatment of laundry e g stain remover prewash sprays etc may damage the surfaces of the washer dryer Keep these agents away from the surfaces of the washer dryer Using a damp cloth immediately remove any fine spray residue and other residue droplets Dosing Dose the detergents and care products according to water hardness ask your water Supply company 16 the manufacturer s specifications on the packaging the amount of laundry soiling Filling the dispensers 1 Dispenser Pull out the detergent drawer Warning Eye skin irritation If the detergent drawer is opened while the appliance is running detergent care product may run out Carefully open the drawer If detergent care product comes into contact with eyes or skin rinse thoroughly If accidentally swallowed seek medical advice Pour in detergent and or cleaning oroduct Detergen
29. multiple plugs couplings or extension cables If a residual current operated circuit breaker is used you use only a type which features this symbol EX Only this symbol guarantees compliance with the currently valid regulations The mains plug is always accessible The power cord is not kinked crushed altered or severed and has not come into contact with any heat SOUICesS Before washing drying for the first time The washer dryer was inspected thoroughly before leaving the factory To remove any residual test water run the Fluff Clean 40 C programme the first time without laundry Note m he washer dryer must have been installed and connected properly Installation and connection Page 37 m Never switch on a damaged machine Inform your customer service Page 35 Insert mains plug Turn the tap on Switch on the appliance Close the washing machine door Do not load any laundry Select the Fluff Clean 40 C programme Open the detergent drawer Pour approx 1 litre of water into dispenser Il Add standard detergent to dispenser Il according to manufacturer s instructions for light soiling Note To prevent frothing use only half the recommended amount of detergent Do not use detergent for wool or delicates 9 Close the detergent drawer 10 Select Start Reload 11 When the programme ends switch off the appliance eee PAn Your washer dryer is now ready for use Installation
30. n units Removing the transportation protection deviceS 004 Hose and cable lengths Connecting the water Water supply 0000 8 Water drainage Drainage into awash basin Drainage into a siphon Drainage into a plastic pipe with rubber sleeve or into a gully Alignment 0002 cee eee Electrical connection Before washing drying for the first time 2 0 0 2 08 Transportation 0004 Intended use For private domestic use only Ihe washer dryer is suitable for machine washable textiles and hand washable wool and for drying certain types of textiles according to care instructions m The appliance is suitable for operation with cold mains water and commercially available detergents and care products which are suitable for use in a washer dryer Always follow the manufacturer s instructions when dosing all detergents cleaning aids cleaning products and cleaning agents m Ihe washer dryer may be used by children over the age of 8 years and by persons with reduced physical sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised or have been instructed by a responsible person Children must not carry out any cleaning or maintenance work without Supervision m Keep children under the age of 3 years away from the washer dryer m Keep pets away from the washer dryer m Install and operat
31. n with Select button the v indicator light comes on The additional function is selected or touch the Select button again to deactive this additional function Temp Spinrpm Option Select Dry Finish in SpeedPerfect For a shorter wash time with a comparable washing effect to the standard programme Note Do not exceed maximum load Overview of programmes Page 20 e EcoPerfect Energy optimised washing by reducing the temperature while achieving a consistent washing result Note The washing temperature is lower than the selected temperature For special hygiene requirements It is recommended that a higher temperature be selected or the 6 SpeedPerfect option be used for a 5 kg load 26 amp Water Plus Increased water level and extended wash time For areas with very soft water or for further enhancing the washing result ey Rinse plus Additional rinse cycle For areas with very soft water or for an even better rinsing result Note Select Rinse Plus by Option button Then touch Select button to select the desired rinse cycles max 3 cycles depend on selected programmes A Less iron Special spin sequence with subsequent fluffing Gentle final spin residual moisture in the laundry increased slightly Uy Prewash Actuate prewash For heavily soiled hard wearing washing e g made of cotton or linen setting the signal en E Setting the sign
32. ng device m When the display panel has gone out at the end of the programme energy saving mode is active To activate select any button 19 en Overview of programmes Overview of programmes Programme onthe programme selector Programme Type of washing Options Information Name of the programme maximum load according to Brief explanation of the programme and which textiles it is suitable ENS0229 for maximum load for washing maximum load for drying selectable temperature in C selectable spin speeds in rom possible additional functions for washing possible settings for drying Cottons max 4 kg 4 kg Hard wearing textiles heat resistant textiles made of cotton or linen cold 90 C Note S v 1400 rpm Reduced load for additional function ERT Aut 1 Aut 2 Easy Care max 3 5 kg 2 5 kg Textiles made of synthetic materials or blended fabrics cold 60 C u 1000 rpm 0 U 5 5 a U Aut 1 Aut 2 Mixed fabrics max 3 5 kg 2 5 kg Mixed load consisting of textiles made of cotton and synthetics cold 60 C w 1400 rom 0 5 24 24 Aut 1 Aut 2 Delicates Silk max 2 kg For delicate washable textiles e g made of silk satin synthetic cold 40 C fibres or blended fabrics 800 rpm Soe a a detergent suitable for machine washable delicate fab e a 20 Overview of programmes Programme Type of washing en Options Information lt Wool Hand and machine washabl
33. ng to EN50229 are conducted using specified load on Cottons 60 C EcoPerfect EU energy label drying performance tests are conducted according to EN50229 Maximum washing load is divided into 2 drying cycles and each drying load is dried by using Intensive Dry Aut 1 option The values may deviate from the stated values depending on the following factors water pressure and hardness inlet temperature ambient temperature type and amount of laundry type and amount of de tergent used fluctuation of power supply and additional functions selected 36 Installation and connection Standard accessories Note Check the washer dryer for damage sustained in transit Do not switch on a damaged washer dryer If you have any complaints contact the dealer where you purchased the appliance or our customer service Depending on the model Aqua Stop Operating and installation instructions Aqua Secure Elbow for fixing the water drainage hose Standard 6 Covers Water supply Power cord Water drainage hose Installation and connection en Note A hose clip 24 40 mm specialist store is also required for connection to a siphon Connecting the water Page 40 Useful tools Spirit level for alignment Page 42 m size 13 socket wrench for loosening the transportation protection devices gt Page 39 and size 17 for aligning the appliance feet Page 42 Installation Note Humidity
34. on only for Rapid 15 Cottons Easy Care Mixed Fabrics Shirts Business and Textile Guards 1 Touch button Dry and activate the function Aut1 or Aut2 2 Do not exceed the maximum loads for drying Overview of programmes Page 20 3 Maximum spin speed for the washing programme will be selected automatically to obtain a good drying result Finish in L4 Define the Finish in time end of programme Note The respective programme duration is displayed by selecting the programme The programme duration is automatically adjusted while the programme is running if the programme duration needs to be changed e g due to changes in the programme default settings Before the programme starts the end of the programme can be preselected in hourly increments up to a maximum of 24h When the programme has started the preselected time is displayed e g 8h and counts down until the programme starts Then the programme duration is displayed e g 2 30 When the programme has started the preselected time can be changed as follows 1 Select Start Reload 2 Select the Finish in button and change the Finish in time 3 Select Start Reload 25 en Selecting additional functions fd Selecting additional functions Select the desired additional functions Option button keep on touching the button until the indicator light of your desired additional functions flashes and then activate the chosen functio
35. or a dash Contents Intended use 4 Safety instructions 5 Electrical safety nananana auaa aa 5 Risk of INnjUTY n on annaa aaa 5 Safety for children 5 Protection of the environment 6 Packaging old appliance 6 Hints and tipS 00008 6 The main points in brief 7 Getting to know your appliance 0000008 8 Washer dryer 000 cee eeee 8 Control panel 64 o 06 284d we52 aad sd 9 Display panel 0008 10 ma Laundry 000 cee e eens 12 Preparing laundry for washing 12 Preparing laundry for drying 13 Sy Operating the appliance 14 Preparing the washer dryer 14 Selecting the programme Switching on the appliance 14 Adjusting the washing programme 14 Adjusting the drying programme 15 Loading the laundry 15 Dosing and adding detergent and Care product 0 16 Starting the programme 17 Childproof lock 00 17 Reloading the laundry 18 Changing the programme 18 Interrupting or ending the Programme 2 eee eee ees 18 End of the programme 18 After washing drying 5 19 en Overview of programmes 20 Programme on the programme selector aaua ee es 20 Drying table nananana aana ee oa 23 SeS E E E E 24 Dyeing Bleaching 05 24 SOAKING 1 ee ee 24 Changing programme defa
36. otated in either button to start interrupt e g reload laundry direction To switch off the washer dryer set and cancel the programme gt Page 18 the programme selector to O Off Display panel for settings and information Select buttons Temp Temperature Spin rpm Spin speed Finish in and Dry for changing default settings gt Page 24 en Getting to Know your appliance Display panel Displays for the programme 90 1400 60 1000 40 800 30 600 eG Z amp O i Oz vy gt ww OL V V V V V V x e L 1 Temperature for washing cold 90 Temperature in C programme 2 Spin speed for washing 1400 Spin speed in revolutions per minute programme w Rinse stop without final drain spin cycle laundry remains in the water after the last rinse cycle L3 Additional functions See details gt Page 26 4 Programme progress and w Prewash information symbols T Washing 7 Rinsing Draining Spinning aa Drying Tap lights up Water pressure too low This extends the programme duration flashes The tap has not been turned on or there is no water pressure Overdosage ey On if too much foam detected one rinse cycle switched on Door lights up When the door can be opened flashes When the programme has started The door is not closed properly Childproof lock lights up On if childproof lock has been activated gt Page 1 10 Drying L5 Programme info
37. ou can find this information on the inside of the door opened service flap and the back of the appliance depending on model Rely on the competence of the manufacturer Contact us You can therefore be sure that the repair is carried out by trained service technicians who carry original Spare parts Customer service en Technical specifications Dimensions COXSI OFCN width x depth x height Weight 83 kg Mains connection Nominal voltage 220 240 V 50 Hz Maximal current 10 A Maximal washing power 2400 W Maximal drying power 1900 W Water pressure 100 1000 kPa 1 10 bar Drain height 60 100 cm 35 en Consumption values Consumption values Programme Option Energy Water Programme consumption Consumption duration kWh liter hours Cottons 20 C 7 0 0 23 is 2A Cottons 40 C 7 0 1 02 T3 ZA Cottons 60 C 7 0 1 10 is 2 Ya Cottons 90 C 7 0 2 05 83 2 Ya Easy Care 40 C EcoPerfect 3 5 0 56 60 1 Mixed Fabrics 40 C 29 0 45 D3 1 Delicates Silk 30 C 2 0 0o 29 Ja Wool 30 C 20 0 18 40 Ja Intensive Dry 4 0 aly 3 0 Me Gentle Dry 25 1 46 3 0 2 Cotone c00 EcoPerfect 7 0 0 70 51 4 Cottons 60 C EcoPerfect 7 0 4 0 4 76 Si 8 Vp Intensive Dry Program setting for tests according to currently valid EU standard EN60456 For comparison test please test the programs with specified load and maximum spin speed EU energy label washing performance tests accordi
38. pliance aligned Align the appliance gt Page 42 Appliance feet fixed Secure appliance feet gt Page 42 Transportation protection devices removed Removing the transportation protection devices gt Page 39 Faults and what to do about them en Faults Cause Remedy Display panel indicator m Power failure lights do not function m Fuse tripped Switch on replace fuse while the appliance is run lf the fault occurs repeatedly call customer service gt Page 35 ning The programme duration m Nota fault unbalanced load detection system adjusts imbalance changes during the wash m Nota fault foam detection function active Additional rinse cycle Cycle Detergent residue onthe m Occasionally phosphate free detergents contain water insoluble residue washing m Select Rinse or brush items when the laundry is dry opin noise during the dry This is an innovative process known as thermal spinning used to reduce ing phase energy consumption during the drying phase Different coloured fluff Run the Fluff Clean cold programme without laundry to remove fluff from the previous drying which has collected in the washer drum during the drying phase cycle is deposited on the laundry during the subse quent wash cycle Water inlet noise during The washer dryer runs a self cleaning cycle to remove fluff which was depos the drying phase the tap ited by the laundry during the drying phase This requires a little w
39. pun at the appropriate spin speed Laundry en Before drying spin at the optimum speed A spin speed of more than 1000 rpm is recommended for cotton more than 800 rom for easy care textiles Do not iron washing immediately after drying It is recommended to roll the washing up first to distribute residual moisture evenly To ensure a good drying performance quilts terry cloths and other large textiles should be dried separately Do not dry more than four terry cloths or 3 kg Do not exceed maximum load 13 en Operating the appliance Operating the appliance Preparing the washer dryer The washer dryer was tested before delivery To remove residual water from the test procedure the first wash cycle should be run without laundry using the Fluff clean programme Before washing drying for the first time Page 43 Note m Never switch on a damaged washer dryer m Inform your customer service gt Page 35 E Insert mains plug 2 Turn the tap on The end of the drying programme is followed by an automatic fluff cleaning cycle The tap must be turned on even when selecting a drying programme ut m Always provide good ventilation in the room where the washer dryer is located so that air produced during the drying phase can be evacuated m Always keep the inlets and outlets for the cooling air clear 3 Open the door 14 Selecting the programme Switching on the app
40. rmation Thine Programme status Door open information Further information Drying mode and the drying time Depends on selected programmes additional functions Q flashes V 1 50 1 24h 7 0 kg 0 PAUS OPEn A 02 E 0 Aut 1 Aut 2 120 OFF Getting to know your appliance en The childproof lock is actived and if the pro gramme selector has been adjusted or the buttons have been pressed On if drying programme is selected Programme duration after programme selection in h min hours minutes Finish in time in h h hour Max load for selected programmes Programme end Programme interrupted End of programme by Rinse stop The door can be opened if programme is interrupted The door cannot be opened Fault display setting the signal gt Page 27 Additional rinse cycles Auto Dry mode 1 Cupboard dry Auto Dry mode 2 Extra dry selected drying time The drying function is deactivated 11 en Laundry Laundry Preparing laundry for washing Sorting laundry according to Sort your laundry according to the care instructions and specifications of the manufacturer on the care labels Type of fabric fibre m Colour Note Laundry can discolour or not be cleaned correctly Wash white and coloured items separately Wash new bright fabrics separately the first time you wash them m Soiling light Do not prewash if necessary select the speedPerfect addi
41. rotection devices which have not been removed may damage the drum for example while the washer dryer is running o prevent damage in transit when transporting the appliance at a later date always re install the transportation protection devices prior to transportation gt Page 43 Keep the screw and sleeve screwed together 1 Take the hoses out of the holders 2 Take hoses out of the elbow and remove the elbow 3 Loosen and remove all 4 transportation lock screws 4 Take the power cord out of the holders Remove the sleeves Installation and connection en 5 Insert the covers Lock firmly by pressing on the locking hook Insert the hose holder Hose and cable lengths Connection on left side 39 en Installation and connection Note If the hose holders are used the possible hose lengths are reduced Available from dealer customer service Extension for Aqua Stop or cold water inlet hose approx 2 50 m Order no WMZ2380 WZ10130 CZ11350 Z7070X0 Longer supply hose approx 2 20 m for standard model Connecting the water Warning Risk of electric shock Danger of death if live parts come into contact with water Do not immerse the Aqua Stop safety device in water it contains an electric valve Caution Water damage The connection points for the water Supply and
42. ss on the cover flap and insert the drainage hose into the holder Note Residual water may run out 6 Carefully unscrew the pump cover Clean the interior pump cover thread and pump housing the fan impeller in the detergent solution pump must be able to rotate 7 Reinsert and screw on the pump cover Handle should be vertical 8 Close the service flap If required engage the disengaged service flap beforehand Note To prevent unused detergent from flowing into the outlet during the next wash Pour 1 litre of water into dispenser Il and start the Spin or Drain programme Drainage hose on the siphon blocked 1 Turn the programme selector to Off Pull out the mains plug 2 Loosen hose clip carefully remove drainage hose Residual water may run out Cleaning and maintenance en 3 Clean drainage hose and siphon spigot 4 Re attach the drainage hose and secure the connection point with the hose clip Filter in the water inlet hose blocked Warning Danger of death Do not immerse the Aqua Stop safety device in water it contains an electric valve First reduce the water pressure in the Supply hose 1 Turn off the tap 2 Select any programme except Spin or Drain 3 Select Start Reload Allow the programme to run for approx 40 s 4 Turn the programme selector to Off Pull out the mains plug 5 Clean the filter on the tap Disconnect the hose from th
43. t for prewash Dispenser amp Softener starch Do not exceed the maximum load Dispenser Il Detergent for main wash water softener bleach stain remover Dispenser A For dosing liquid detergent Notes Always follow the manufacturer s instructions when dosing all detergents cleaning aids care products and cleaning agents Dilute viscous fabric softener and fabric conditioner with water This will prevent blockages Be careful when opening the detergent drawer while the appliance iS running m If an individual drying programme is selected please do not add detergent and or care product in the appliance Measuring aid for liquid detergent depending on the model Position the measuring aid for measuring the correct amount of liquid detergent 1 Pull out the detergent drawer Press down the insert and fully remove the drawer 2 Slide the measuring aid forwards fold it down and click it into place 3 Reinsert the drawer Note Do not use the measuring aid for gel detergents and washing powder or for programmes with prewash or when Finish in time is selected For models without a measuring aid pour the liquid detergent into the appropriate dispenser and place it in the drum Operating the appliance en Starting the programme Select Start Reload The indicator lamp is lit and the programme starts Note If you want to secure the programme to prevent it from being adjusted inadvertent
44. teel cleaner m Do not clean the appliance with a water jet Drum Use chlorine free cleaning agents do not use steel wool Descaling Not required if detergent dosed correctly However if this does occur 28 follow the instructions of the descaling agent manufacturer Suitable descalers can be purchased on our website or from customer service Page 35 Cleaning the detergent dispenser If it contains detergent or fabric softener residue 1 Pull out the detergent drawer Depress the insert and remove the drawer completely 2 Take out insert using your finger oress insert upwards 3 Clean the detergent dispenser and insert with water and a brush and dry 4 Attach the insert and lock into position push the cylinder onto the guide pin 5 Insert detergent drawer Note Leave the detergent drawer open so that residual water can evaporate Drain pump blocked Z Warning Risk of scalding Washing water is hot when washing at high temperatures You may be scalded if you touch the hot washing water Allow the washing water to cool down 1 Turn the tap off to prevent more water from flowing in and to ensure that it is drained via the detergent solution pump 2 Turn the programme selector to Off Pull out the mains plug 3 Open the service flap 4 Take the drainage hose out of the holder 5 Remove the cover flap draining the washing water into a suitable container Pre
45. tional function normal Select programme with prewash If required pretreat stains heavy Load less washing Select programme with prewash If required pretreat stains Stains Remove pretreat stains while they are fresh Firstly dab with a soap water do not rub Then select the appropriate programme and wash the items Stubborn or dried in stains can sometimes only be removed by washing several times m Symbols on the care labels Note The numbers in the symbols indicate the maximum washing temperature that may be used KY Suitable for normal washing process e g Cottons programme KE A gentle washing process is required e g Easy Care programme 12 KE An especially gentle washing process is required e g Delicates Silk programme Suitable for washing by hand e g Wool program 19 4 Do not machine wash Protecting your laundry and washer dryer Caution Damage to the appliance textiles Foreign objects e g coins paper clips needles nails may damage the washing or components of the washer dryer The following instructions must be observed when preparing your laundry Always follow the manufacturer s instructions when dosing all detergents cleaning aids care products and cleaning agents Do not exceed maximum load Overfilling will impair the washing result m Keep detergents and agents for the pretreatment of laundry e g stain remover prewash sprays etc away
46. towels Dry weight in kg 05 1 0 10 20 20 30 30 40 05 10 20 25 Estimated drying time in min Adjustable drying time in min Cupboard dry Auti lt 60 60 85 85 120 120 160 a he Extra dry Aut2 lt 65 65 100 100 140 140 170 Se Intensive Dry Auto Intensive Dry Time Quilt terry cloth larger or thick textiles made of cotton such as terry cloths bed sheets table cloths jeans work clothes Dry weight in kg 05 1 0 10 20 20 3 0 30 40 05 10 15 20 Estimated drying time in min Adjustable drying time in min Cupboard dry Auti lt 70 70 95 95 130 130 170 60 90 120 Extra dry Aut2 e e 75 110 110 150 150 180 eats Intensive Dry Auto Intensive Dry Time Easy care Textiles made of synthetic or blended fabrics such as shirts sportswear delicate items Dry weight in kg 05 1 0 10 20 20 25 05 10 15 2 0 Estimated drying time in min Adjustable drying time in min Cupboard dry Auti lt 55 55 95 95 130 Extra dry Aut2 lt 65 65 130 130 160 Recommended programme 30 60 90 120 Gentle Dry Auto Gentle Dry Time i Thetimes are approximate and refer to a normal load standard spin programme and room temperature i The maximum selectable drying time is 120 min If the laundry weighs more than 2 5 kg select automat ic drying This function is recommended to ensure good drying results and save energy The 15 minute drying programme is used to cool the laundry 23 en Changing programme default settings Starching Note The laundry should
47. ult settings 24 OMG gic hie E ord as he card race 24 DOOM TOMes 232 enue cas neeen vas 24 1B Ere ee ee ee ee 24 PINSI WE lig co saire oy teen Sh Gite ee cs oe eg 25 Selecting additional functions os 605 6c0 0600082 5 26 speedPerfect 26 ECOPEMECT 6 x s wdew tind a nearness 26 amp Water Plus 00 26 wy Rinse pluS 008 26 LESS Iron 1 ee 26 Uy PICWASI soe dan ee eal sed ocd 26 Ei Setting the signal 27 Cleaning and maintenance 28 Machine housing Control panel 28 DUT eeraa 4 r e amp ee ee a 28 Descaling oananananaaa re Ak wnat de oe 28 Cleaning the detergent dispenser 28 Drain pump blocked 28 Drainage hose on the siphon blocked e428 d et dob Barns 29 Filter in the water inlet hose blocked 2 ee es 29 Air filter blocked 0005 30 Faults and what to do about them 0 0000 30 Emergency release e g if a power failure OCCUIS 1 aa 30 Information on the display panel 31 Faults and what to do about them 32 en Intended use Wee s Customer service Technical specifications a Consumption values Installation and connection Standard accessories Installation 0 eee Secure installation Installation area ee ee ee Installing the appliance on a base or on a wooden joist ceiling Installing the appliance under between kitche
48. um load for the drying phase is less than the maximum load for the wash cycle Unload the washer dryer after wash ing with the maximum load and divide the laundry into two drying cycles The power supply voltage is too low below 200 V provide a suitable power supply Air filter blocked Clean the air filter gt Page 30 Thick multilayered textiles or textiles with thick fillings dry easily on the sur face but not inside This equalisation process may take longer For these types of textiles select the timed drying programmes The drying time is reduced for a smaller load Some residual moisture may remain in the dryer system If the door is opened quickly a suction effect is generated which causes the moisture to drip out of the dryer system Open the door slowly Avoid wrenching the door open If a fault cannot be rectified switching the machine on and off or a repair is required m Set the programme selector to Off and pull out the mains plug m Turn off the tap and call customer service gt Page 35 34 Customer service If you cannot correct the fault yourself see section Faults and what to do about them gt Page 32 please contact our customer service We will always find a suitable solution and aim to avoid unnecessary visits by technicians Please give customer service the product number E Nr and the oroduction number FD of the appliance E Nr eS FD Product number Production number Y
Download Pdf Manuals
Related Search