Sencor SCA BA01 V2 alcohol tester
Contents
1. 2 Note Remove the batteries if you will be storing the device or not using it for an extended period of time Batteries must not be exposed to excessive heat such as sunlight fire etc The incorrect use of batteries may lead to a electrolyte leak and corrosion To ensure that the device works correctly proceed according to the instructions below Do not insert the batteries in the wrong direction Do not charge heat open or short the batteries Do not throw batteries into a fire Do not leave discharged batteries in the device Do not combine various types of batteries or new and old batteries If you will not be using the device for a longer period of time remove the batteries to prevent potential damage caused by a subsequent battery leakage If the device is not working correctly or its efficiency is reduced change all batteries for new ones If electrolyte leaks out from the batteries have the device cleaned by an authorised service centre Application 1 2 It is important to rinse your mouth with clean water before use Do not smoke or drink alcoholic beverages for at least 5 minutes before use Insert a straw or the blowing tube into the inlet opening above the LCD display Press the START button for a short time to turn on the device The preheat sensor is activated for a period of approximately 18 seconds PH will blick once on the display and then the display will show Wait and a countdown wil2. electronic products must not be added to ordinary municipal waste For proper disposal and recycling take these products to designated collection points Or as an alternative _ in some European Union states or other European countries you may return your appliances to the local retailer when buying an equivalent new appliance Correct disposal of this product helps save valuable natural resources and prevents damage to the environment caused by improper waste disposal Ask your local authorities or collection facility for more details In accordance with national regulations penalties may be imposed for the incorrect disposal of this type of waste For business entities in European Union states If you want to dispose of electric or electronic devices ask your retailer or supplier for the necessary information Disposal in other countries outside the European Union This symbol is valid in the European Union If you wish to dispose of this product request the necessary information about the correct disposal method from the local council or from your vendor d This appliance meets all the basic requirements of EU directives that apply to it Changes in the text design and technical specifications may change without prior notice and we reserve the right to make these changes Copyright 2012 Fast R a s Revision 08 2012 EN 8
3. minutes EN 4 Warning signals Low value A measured value lower than 0 1 BAC will be displayed as 0 0 low value with a GREEN backlight Warning The measured value equals or is greater than the value warning concentrated value A sound signal will be made and NO DRIVING driving forbidden will start flashing on the screen for about 15 seconds The display s backlight will alternate colours GREEN AND RED The measured value will be shown and a message NO DRIVING driving forbidden will stay lit on the display If the measured value is greater than 4 o NO DRIVING Driving forbidden and HI high value will appear on the display Press the MODE button to cancel the sound signal IT IS FORBIDDEN TO DRIVE if the low warning value is exceeded EN 5 Important notices To ensure accurate measurement results it is necessary to perform so called auto cleaning if you have not used the device for longer than 2 weeks especially before first use Start the auto cleaning process by removing the batteries and reinserting them and turning on the device The indicator AUTO CLEANING will start to flash The auto cleaning process takes approximately 5 minutes and there will be a countdown on the display for during this time A sound signal will be made in the final minute of the auto cleaning The device will automatically turns itself off after 1 minute and the auto cleaning process will be completed Che
4. SCA BA01 V2 User s manual Breathalyser Carefully read the entire user s manual before using the device and understand the safety measures and detailed operating instructions for the device Store the user s manual in a safe place for future reference If you sell the device do not forget to provide the user s manual to the new owner together with the device and its accessories Important safety measures IMPORTANT Using the breathalyser immediately after or within 15 minutes of consuming alcohol may damage the detection sensor and there is a danger of future measurements being inaccurate Unprofessional operation of this device is not covered by the warranty e Do not perform tests in strong winds or in a closed room which is filled with cigarette smoke or contains alcohol vapours e Ifthe flat batteries symbol appears on the display replace them with new ones Do not blow smoke food or liquids into the mouthpiece e Use the device only in an environment where temperatures are between 10 and 40 C Use in an environment outside this range may damage the device and may lead to incorrect test results e The level of alcohol in the breath depends on many factors that change in time The level can change already several minutes after the initial test e The measurement results of this device cannot be used in legal proceedings as evidence e The information obtained using this device is only informative in nature We reco
5. ck that no residual alcohol has remained inside the space for blowing tube before performing a test If you press the START button for approximately 2 seconds you will end the auto cleaning process and turn off the device Or press the START button for a short time to start measurement and to skip the auto cleaning function To achieve accurate measurements you should check that there is no residual alcohol in the device before using the device You can inspect the device until LO low value appears on the display You can achieve this by pressing the START button once Press and hold the START button for several seconds and blow into the blowing tube If necessary you may shake the device back and forward several times which may remove residual alcohol from the device After 4 repeated tests let the device rest for 2 minutes If the message Er flashes on the display for longer than 5 seconds it may indicate incorrect handling You did not press and hold the START button during the test Press any button to end the error sound signal If you will not be using the device store it in a dry place If the low battery condition indicator light starts flashing the measurement is not accurate and it is necessary to replace the batteries without delay If the difference between two subsequent measurements is greater than 0 1 o you must repeat the measurement EN 6 Technical specifications Measuri
6. l commence EN 3 Important Wait until the preheating process is completed because the sensor needs to heat up As soon as the countdown is completed the display will show READY and a sound will be made informing you that the device is ready for operation At the same time the BLOW indicator light will start to flash on the display informing the user that it is necessary to blow into the tube 4 Press and hold the START button and the BLOW will light up and you will hear a long sound signal It is necessary blow into the tube at the same time It is necessary to blow into the tube with a constant force for approximately 6 seconds Stop blowing as soon as you hear a short sound signal The display will show the appropriate information i A measured value lower than 0 1 o BAC will be displayed as 0 0 low value ii A measured value between 0 1 o 4 o BAC will appear on the display iii A measured value larger than 4 o BAC will cause HI high value amp NO DRIVING Driving forbidden to appear on the display 5 Press the START button for a short time to start another test You may use the device again as soon as the countdown is completed and the READY indicator appears on the display together with a sound signal 6 Press the START button for approximately 2 seconds to turn off the device The device will turns itself off automatically if you do not press any button within 2
7. mmend that it is not used for making decisions about the ability to perform any activity requiring responsibility Several factors e g natural gas remains smoke and undesirable breath may influence the level of the measured values e Do not allow yourself or anybody else to drive a vehicle after consuming alcohol If you have consumed alcohol always organise for a designated driver or use an alternative form of transport e Neither the vendor nor the manufacturer are responsible for damages caused by the use of this device NEVER DRINK ALCOHOL IF YOU ARE PLANNING TO DRIVE A MOTOR VEHICLE Attention It is recommended to have the accuracy of the device tested after a year of use With more frequent use the lifetime of the device may be used up and the measurement results may not be accurate EN 1 Description of the device READY indicator light Blowing tube OE Battery condition indicator N Driving forbidden symbol LCD display ON button START Battery Installation 1 Remove the battery compartment cover 2 Insert two AAA alkaline batteries according to the polarity shown in the battery compartment 3 Return the cover back to its place 4 After inserting batteries the auto cleaning process will automatically commence The auto cleaning indicator will start to flash and the display will countdown the time 5 You will be able to use the device after the auto cleaning function is completed EN
8. ng range 0 1 4 o Battery 2 x 1 5V AAA alkaline batteries Display Digital LCD display with a two colour backlight Unit o or BAC or mg l optional Automatic shut off 2 minutes Duration of test gt 6 seconds Test preparation time 25 seconds Dimensions h x w x d 98 x 36x 16mm Weight Approx 27 g without batteries Warning calibration value 0 2 o Accessories 3 blowing tubes The above stated data may be changed without giving reason Do not forget that the measured value may be affected by many factors such as gas pollution in the air smoke and various mouth odours Therefore consider the measured value only as informative in nature Neither the manufacturer nor the vendor take any responsibility arising from the use of this device Caution Using the breathalyser immediately after or within 15 minutes of consuming alcoholic beverages may damage the detection sensor there is a danger of future measurements being inaccurate Unprofessional operation of this device is not covered by the warranty Disposal of used batteries Take used batteries to designated collection points Follow the regulation in force in your country EN 7 INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Take the packaging material to a designated municipal waste facility DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT This symbol on products or original documents means that used electric or
Download Pdf Manuals
Related Search