Sencor SBC 2318 beertender
Contents
1. as Revision 1 2012 Beer Dispenser SBC 2318 INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Dispose of packaging material at a public waste disposal site DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES The meaning of the symbol on the product its accessory or packaging indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of waste Please ask your local authorities or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union If you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union If you wish to dispose of this product request the necessary information about the correct disposal method from local governm2. carry or handle the appliance in any other way while it is running or if a keg is installed in the chilling compartment Storage If you will not be using the appliance for an extended period of time then Remove the keg Thoroughly clean out the appliance Check that liquid remains are not left inside the appliance Cover the appliance so that it is protected against dust and store it in its original packaging Store the appliance in a dry place Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 DESCRIPTION OF THE APPLIANCE Drip tray Temperature display Tap Lid Tap handle Lid opening mechanism Ventilation openings Fan Input power socket On Off switch Temperature control dial Feet of the appliance amp 6 69 3 9 O amp G9 9 69 C Copyright 2011 Fast CR as Revision 1 2012 Beer Dispenser SBC 2318 Accessories not compulsory Connecting beer hose 4 hoses one already has the retainer block attached Drip tray Drip tray underlay Connecting air hoses 2 hoses one is already attached Tubing to the keg yellow Tubing to the keg white Power cord Copyright 2011 Fast CR a s Tap seal rings Tap handle Hose clips for fastening hoses to the keg adapter Keg adapter blue Keg adapter blue green Plug for the blue green adapter if necessary Keg adapter yellow Spatula for removing froth Revision 1 2012 Beer Dispens
3. edge of the tap Pic 28 3 While inserting it turn it to make the screwing on easier Lift the tap handle Pic 28 1 and release it Place the keg into the chilling compartment so that the air fitting Air In Pic 29 1 faces backwards Connect the air fitting Air In Pic 29 1 to the air fitting Pic 29 2 using the air hose Pic 29 3 In this step the arrow on the air hose must face in the direction of the air fitting Air In on the keg adapter Attention Check that the air hose is pushed far enough on to the fitting An air hose that is not pushed on far enough may come loose And this may result in the release of the pressurised liquid EN 13 Copyright 2011 Fast CR as Revision 1 2012 Beer Dispenser SBC 2318 For pouring it is necessary to slowly insert the beer hose Pic 30 1 into the pouring adapter It is necessary to push hard enough so that it penetrates the protective plug on the keg If you have pushed the entire beer tube downwards turn it to lock it in place Insert the retainer block Pic 30 2 into the cavity of the appliance Do not forget to also take the retainer block when changing the hose Pic 30 17 Secure the beer hoses in their place using clips Pic 30 3 RI Note Do not tangle the hoses Otherwise the it may be im possible for the liquid to flow through the hoses If necessary turn the keg so that the hoses are not tan gled 18 Close the lid of
4. of the appliance requires that it is appropriately located Adhere to the following instructions e Protect the appliance against the effects of weather e Protect the appliance against moisture which could enter from the external environment EN 3 Copyright O 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 Never place the appliance on a heat source or in the direct vicinity of a heat source e g hotplate oven etc Avoid direct sunlight Temperatures above 35 C may damage the appliance The appliance should be located at least 10 cm from a wall or other items so that proper ventilation of the coolant is ensured Check that the ventilation openings Pic 1 7 and the fan Pic 1 8 are not covered During connection or pouring the liquid may spray out on to furniture wallpaper etc Therefore we recommend that an easy to maintain room is chosen e g kitchen Locate the appliance on an even and stable surface so that it cannot fall The feet of the appliance Pic 3 1 have sharp edges which may scratch fine surfaces Therefore we recommend that an underlay e g a rubber mat is placed under the appliance to avoid scratching Pic 3 2 Handling beverages requires special care in the area of hygiene Bacteria dangerous to health may accumulate in the parts of the appliance e g in the hoses if not properly cleaned where excess liquid remains The bacterial cultures may cause serious illnesses and health co
5. see chapter Connecting and not display chilling Check that there is a voltage in information the power socket with the help of another working electrical appliance The appliance is not Turn on the draught system chapter powered main circuit Connecting and chilling is turned off The beer does The appliance is not Turn on the draught system chapter not flow turned on Connecting and chilling The keg is empty Take out the keg The adapter on the Open the keg adapter keg is closed The hose is pinched Move the keg so that the hose is set free see chapter Installing a keg Creation of First glass The first glass always contains a large a large amount amount of head froth This is normal It is of head froth necessary to pour several glasses before the froth becomes thinner The keg is not cold Continue chilling enough The keg was shaken Place the keg in a location where it will not up be handled for at least 4 hours see chapter Installing a keg The tap is not open Always open the whole tap see chapter enough Pouring beverages The pump Air is leaking out of Attach the air hose properly If necessary is activated the air hose use a new air hose see chapter Installing frequently a keg The keg adapter is not Place the keg adapter in the proper position in the proper position see chapter Installing a keg EN 21 Copyright 2011 Fast CR as Revision 1 2012 Beer Dispenser SBC 2
6. the appliance Pic 1 4 The appliance is now ready to be turned on see chapter Turning on and cooling EN 14 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 6 litre beer keg To connect the keg you will need the following accessories e Keg adapter blue Pic 2 12 e 1 air hose Pic 2 5 e 1 beer hose Pic 2 1 The 6 litre beer keg Pic 31 is offered by many European beer distributors Its fitting is compatible with the keg adapter of the dispenser unit Pic 31 Remove the protective film and packaging material with the hose on the keg You may throw these parts away Release the seal Pic 32 1 from the keg adapter Pic 32 2 so that the adapter is free Place the adapter on to the lock of the keg Check that the adapter is firmly seated on the keg Open the lid of the appliance Pic 1 4 Place two hose clamps on the bottom part of the beer tube Pic 33 1 These two clamps will later be used to secure the beer hoses on to the tap adapter Slowly press down on the tap handle Pic 34 1 downwards Insert the beer tube Pic 34 2 into the tap until its other end extends past the edge of the tap Pic 34 3 While inserting it turn it to make the screwing on easier Lift the tap handle Pic 34 1 and release it EN 15 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 10 Place the keg into the chilling compartment
7. 318 Beer is leaking The keg adapter is not Close the keg adapter when the keg closed adapter is inserted The pressure inside the Continue chilling keg is too high Place the keg in a location where it will not be handled for at least 4 hours see chapter Installing a keg The displayed The keg is not entirely Continue chilling see chapter Connecting temperature is and chilling increasing on its own The beer is not The lid is open Close the lid cold enough f The ventilation Keep the ventilation openings and fan free openings are clogged _ from obstructions The ambient Move the appliance away from sources of temperature is too heat and direct light high The appliance is The pump or the When connected the pump and compressor too loud compressor are turn on and off automatically This is running normal EN 22 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 TECHNICAL SPECIFICATIONS Type of appliance Voltage Power input Insulation Dimensions Weight Cooling Chilling temperature Climatic class Capacity of the pump Pressure in the pump 4 litre beer keg Suitable kegs 5 litre beer keg 6 litre beer keg Material Hoses silicone Keg adapter ABS Acrylonitrile butadiene styrene Due to constant product development we reserves the right to make technical and design changes Mistakes and errors in the text reserved EN 23 Copyright 2011 Fast CR
8. Beer Dispenser User s manual SENCOR SBC 2318 Prior to using this appliance please read the user manual thoroughly even if you are already familiar with similar types of appliances Use the appliance only as described in this user manual Keep the manual for future use Save the original shipping transport box packaging material receipt and warranty card for the duration of the warranty When transporting pack the appliance in the original packaging materials only Revision 1 2012 Copyright 2011 Fast CR as Beer Dispenser SBC 2318 CONTENTS SAFETY PRECAUTIONS eelere EE DESCRIPTION OF THE APPLIANCE E FUNCTIONS OF THE BEER DISPENSER SYSTEM 2er t ertt SETTING UP AND CONNECTING KEGS ee eege dee Ee eode xU ref Cx uet INS TALEIN G A cg crm TURNING OW AND COOLING 225i nitet ieina aea aeei POURING TEE REMOVING THE KE ET SPORING EGIS eddie oit a ing eee esate eed age eon EO CARE AND MAINTENANCE scrire aud a mius eusice Pa dun cU Crit iid eier e Leen KL TECHNICAL INFORMATION WE INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS eene DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT EN 2 Copyright 2011 Fast R a s Revision 1 2012 Beer Dispenser SBC 2318 SAFETY PRECAUTIONS For your safety and the safety of your appliance please adhere to the following instructions e Do not leave the appliance without supervision This appl
9. and press on the tap handle to release excess pressure in the keg A small amount of beer will flow out of the tap in this step 3 Once beer stops flowing out of the appliance release the tap handle 4 Open the lid of the appliance 5 Pull out the air hose Note It may be difficult to pull the air hose out It is necessary pull firmly 6 Pull out the beer hose from the adapter and lift it up 7 Again press the tap handle so that the hose is completely empty and leave the tap open 8 Pull the beer hose out of the tap 9 Release the tap handle 10 Take out the keg 11 If you wish to store the keg place the keg with the adapter attached into a refrigerator If the keg is empty remove the keg adapter 12 Thoroughly wash out the appliance and all accessories STORING KEGS You can store kegs in a turned on appliance for various lengths of time Always leave the appliance turned on when maintaining the required temperature in a keg 4 litre and 6 litre kegs have a system installed which separates the injected air from the beer For this reason beer may be stored in the keg for longer You may store the kegs in the appliance for several days see printed material that come with the keg for more information if you pour at least once per day Otherwise remove the keg from the appliance and store it in a refrigerator Connect again if necessary The 5 litre beer keg does not have system that separates the air from the beer Th
10. art thoroughly Allow the accessories and the appliance to dry in an open location for at least 24 hours before storing Warning For hygiene reasons do not install accessories in advance Store them separately in side the appliance Handling beverages requires special care in the area of hygiene Bacteria dangerous to health may accumulate if excess liquid remains are left in some part e g in the hoses if not properly cleaned of the appliance We therefore recommend that the appliance is thoroughly cleaned after every use Warning Risk of injury by electrical shock Before cleaning the appliance turn off and discon nect it from the power source disconnect it from the power socket Do not allow any liquid to enter inside Never place the appliance into water or other liquids Warning Risk of scalding by hot water Check that the water used for washing is not too hot Attention Neither the appliance nor the accessories may be washed inside a dishwasher EN 20 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 TROUBLESHOOTING Before you send the appliance to an authorised service centre check whether you can remedy the defect using the table below Warning Before troubleshooting always turn off the appliance and disconnect it from the power socket Never use a damaged appliance Temperature The appliance is not Properly connect the appliance to a power display does turned on socket
11. d insert it under the beer dispensing system Pic 1 1 Check that the drip tray is not protruding to avoid tipping it over accidentally Attention The feet of the appliance Pic 4 1 have sharp edges which may scratch a fine surface Warning Do not connect the power cord to a power source or turn the appliance on yet To prevent any possible accidents caused by the entry of liquids into the appliance con nect it and turn it on only after installing a keg Instructions for connecting the pow er cord and turning on the appliance are found in chapter Turning on and cooling After connecting the appliance it is necessary to wash it out thoroughly EN 7 Copyright 2011 Fast CR as Revision 1 2012 Beer Dispenser SBC 2318 Washing out for the first time Before first use all parts must be thoroughly cleaned to remove any health damaging liq uid remains which could cause serious illnesses or potential health complications Warning Use the appliance only after all its parts are clean Using the appliance when it is dirty may cause serious illnesses or potential health complications e Remove the hoses which have already been set up at the appliance connecting hoses air hoses e Amore detailed description of the cleaning process can be found in chapter Care and maintenance e After cleaning the appliance for the first time you may connect kegs see chapter Installing a keg INSTALLING A KEG Whe
12. e air fitting Pic 20 2 using the air hose Pic 20 3 In this step the arrow on the air hose must face in the direction of the air fitting Air In on the keg adapter Attention Pic 20 Check that the air hose is pushed far enough on to the fitting An air hose that is not pushed on far enough may come loose And this may result in the release of the pressurised liquid 21 Insert the retainer block Pic 21 1 into the cavity of the appliance Do not forget to also take the retainer block when changing the hose 21 Press the free end of the hose into the beer fitting Beer Out Pic 21 2 Attention Check that the hose is pushed far enough on to the fitting A beer hose that is not pushed on far enough may come loose And this may result in the release of the pressurised liquid Q Note Do not tangle the hoses Otherwise the it may be impossible for the liquid to flow through the hoses If necessary turn the keg so that the hoses are not tangled 22 Push the hose clamp over the hose and the beer fitting Beer Out Pic 21 2 23 Secure the beer hose using the clamp Pic 21 3 24 Move the lock Pic 21 4 to the Open position 25 Close the lid of the appliance Pic 1 4 The appliance is now ready to be turned on see chapter Turning on and cooling EN 11 Copyright 2011 Fast CR as Revision 1 2012 Beer Dispenser SBC 2318 4 litre beer keg To connect the keg you will need
13. e that sometimes the shown temperature may vary from the current temperature in the keg it de pends on pre chilling 2 Wait until the keg is chilled to the required temperature The chilling time may vary depending on the initial temperature and the size of the keg It takes approximately 5 hours to cool down a 5 litre keg from 25 C to 5 C It takes approximately 1 hour to cool down a 5 litre keg from 10 C to 5 C Attention Never leave kegs in a freezer The contents of the keg may freeze and the keg may be damaged Important notice On the underside of the lid there is a switch used to activate and deactivate the pressurisa tion of the keg EN 17 Copyright O 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 If the switch is in the top position the pressurisation function is activated If the appliance is connected to a power source and the main switch is in the ON position on the pres surisation function will be activated when the lid is closed If the switch is in the lower position the pressurisation function is deactivated Pressure deactivation can be used in the event that you first want to only chill the keg and then later connect it to the draught system POURING BEVERAGES 1 Take a clean rinsed glass and place it under the tap Warning For hygiene reasons make sure that the tap is not submerged in the beverage Beer that has dried on to the tap may spoil head formation 2 Pull
14. ent departments or from your seller This product meets all the basic EU regulation requirements that relate to it EN 24 Copyright 2011 Fast CR a s Revision 1 2012
15. er SBC 2318 FUNCTIONS OF THE BEER DISPENSER SYSTEM In the chilling compartment of the beer dispensing system there is a keg chilled to a set tem perature Various keg adapters ensure the connection of various kegs to the dispensing system Compressed air is generated by means of a pump which is located inside the dispensing sys tem This compressed air is delivered to the keg creating excess pressure inside the keg and enabling the beverage to be drawn from the keg The beverage is easily poured through a tap SETTING UP AND CONNECTING KEGS Unpack the appliance and all accessories and check that the appliance including accesso ries is complete see chapter Description of the appliance Attention Always transport the appliance in the original packaging to avoid damaging the ap pliance Store the packaging in a safe location for the purpose of further transport Dispose of packaging that is no longer used in accordance with other legal regula tions in the given country Assembling 1 Select an appropriate location 2 Place the anti scratch underlay e g a rubber mat Pic 4 2 on which the appliance will stand This will prevent scratching the surface 3 Insert the tap handle Pic 1 5 with the mark facing forward The tap handle needs to be pushed into the holder with appropriate force 4 Remove the protective film from the drip tray Pic 2 3 5 Place the drip underlay Pic 2 3 into the drip tray Pic 2 3 an
16. erefore the beer should not be stored for longer than 24 hours in a turned on appliance The beer will spoil within 24 hours Warning Check the brewer s information on the beer keg labels EN 19 Copyright 2011 Fast CR as Revision 1 2012 Beer Dispenser SBC 2318 CARE AND MAINTENANCE 1 2 Take off all hoses and take the keg out of the appliance Wash the appliance with only a lightly dampened cloth Do not use any cleaning agents cleaning sands or alcohol as these substances may scratch the appliance A Attention Do not tilt or turn over the appliance to fully empty the remaining liquid remaining d pes A A Warning gt gt E in the chilling compartment The liquid could enter inside the appliance Rather use a wiping cloth to suck up any liquids Use a wiping cloth to suck up the remaining liquid that may have remained in the chilling compartment Wash out the chilling compartment using a dishwashing detergent and wipe dry with a soft wiping cloth Wash the inside of the tap using a dishwashing detergent rinse it out and wipe dry with a corner of a wiping cloth Wash out all hoses which can be removed or which come into contact with the liquid accessories and the drip tray in hot water with dishwashing detergent Turn the keg adapters around several times so that you clean out also from the hard to reach angles Rinse all parts under running water to remove excess cleaning agents Dry all p
17. g is suitable for inserting the keg tubing If any part is blocked you must remove the plastic trim ming on the keg opening Pic 16 B You will probably need tools such as for example a screwdriver or pliers Warning Only use clean tools as the use of dirty tools could contaminate the beer 8 After removing the plastic trimming insert the plug Pic 17 1 9 Insert the adapter with the installed keg tubing Pic 17 2 into the keg opening or into the plug 10 Have a towel on hand for the case that beer may leak in one of the following steps 11 Slowly push the keg adapter down so that the side brackets fit in 12 Now check that the keg adapter is firmly seated 13 Open the lid of the appliance Pic 1 4 14 Place two hose clamps on the bottom part of the beer hose Pic 18 1 These clamps will later be used to secure the beer hoses to the keg adapter 15 Slowly press down on the tap handle Pic 19 1 16 Insert the beer tube Pic 19 2 into the tap until its other end extends past the edge of the tap Pic 19 3 While inserting it turn it to make the insertion easier 17 Lift the tap handle Pic 19 1 and release it EN 10 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 18 Place the universal keg into the chilling compartment so that the air fitting Air In Pic 20 1 of the keg adapter faces to the rear 19 Connect the air fitting Air In Pic 20 1 to th
18. iance may not be used by any persons including children with mental disabilities weak strength by inexperienced persons unless they have been properly trained or schooled in the safe use of the product or unless they are properly supervised by a qualified person who is responsible for their safety This appliance must not be use by persons under the effect of narcotics e Children must be supervised to ensure that they do not play with the product e Alcoholic beverages are harmful to children s health e Under no circumstances should children come into contact with the packaging materials There is a risk of suffocation e Any other use is considered to be incorrect and is forbidden Using the beer dispenser system for pouring non foodgrade liquids is strictly forbidden Likewise the beer dispenser system should not be used to pour beverages containing milk sticky beverages and beverages with a thick consistency or beverages containing fruit pulp The appliance is connected to the mains under electrical current Pay increased attention as contact with live parts e g in the event of damaged insulation is lethally dangerous Therefore adhere to the following instructions e Never touch the power plug with wet hands e f you wish to disconnect the appliance from the power socket always only pull on the power plug Never disconnect the appliance from the power supply by pulling on the power cord there is a risk that it may tear e Check
19. mplications Therefore adhere to the following principles Thoroughly wash out with lukewarm water all the parts of the dispensing system which may come into contact with the beverage immediately after every use see chapter Care and maintenance If you are not sure wash out the given parts also before using the appliance Wash out all parts of the dispensing system when replacing kegs Like a refrigerator this appliance also has a cooling circuit with coolant In this respect adhere to the following safety measures The coolant should not leak out into the environment This means that the cooling circuit inside the appliance should not be damaged Leaking coolant is highly flammable If coolant is leaking from the appliance avoid any contact with a cigarette lighter or an open flame After discovering a coolant leak immediately ventilate the room Leaking coolant may affect the eyes In the event that they are affected seek medical help Transport For standard transport always hold the appliance by the bottom part and never by the lid The appliance is equipped with an oil filled compressor This means that it must always be transported in the vertical position and operated seated on a horizontal surface on all 4 feet In the event that the appliance is transported on its side then we recommend that the appliance is left to stabilise for at least 3 hours before being turned on again Otherwise the compressor could be damaged Do not
20. n connecting kegs it may happen that liquid will flow out of the appliance due to an operating mistake or due to the kegs being pressurised more than usual For this situation prepare the following Bucket to catch excess liquids Sufficient number of towels for wiping the excess fluids Wear suitable clothing on which potential spraying or staining will not matter Warning Liquid remains may contain bacteria and pathogenic substances which may cause serious illnesses or potential health complications Check that the appliance and all accessories have been thoroughly washed out before every use Wash out the parts where you are not sure whether they have been washed out or not see chapter Care and maintenance Wash out all parts every time a keg is replaced A Attention Before use store kegs in a location where they will not be handled A keg that has been shaken is highly pressurised This causes the formation of a large amount of head and may cause the connecting hoses to come loose Keep these over pres surised kegs for at least 1 day in a location where it is certain that they will not be handled Tf Note We recommend the kegs be chilled in advance to prevent excessive head froth for mation and subsequent problems with the connecting hoses You may chill the kegs by placing them inside the appliance without connecting them A Attention Do not place kegs in a freezer The contents of the keg may freeze and the keg ma
21. so that the air fitting Air In Pic 35 1 of the keg adapter faces to the rear 11 Connect the air fitting Air In Pic 35 1 to the air fitting Pic 35 2 using the air hose Pic 35 3 In this step the arrow on the air hose must face in the direction of the air fitting Air In on the keg adapter Pic 35 A Attention Check that the air hose is pushed far enough on to the fitting An air hose that is not pushed on far enough may come loose And this may result in the release of the pressurised liquid 12 Insert the retainer block Pic 36 1 into the cavity of the appliance Do not forget to also take the retainer block when changing the hose 13 Press the free end of the beer hose into the beer fitting Beer Out Pic 36 2 73 14 Allow the hose clamps Pic 36 3 to gently slide on to the beer hose and the beer tube Note Check that the beer hose is pushed far enough on to the fitting A beer hose that is not pushed on far enough may come loose And this may result in the release of the pressurised liquid Q Note Do not tangle the hoses Otherwise the it may be impossible for the liquid to flow through the hoses If necessary turn the keg so that the hoses are not tangled 15 Secure the beer hoses in their place using clamps Pic 37 1 16 Press the keg lock Pic 37 2 by a quick downward motion and turn it to position Open 17 Close the lid of the appliance Pic 1 4 The appliance is no
22. that the power cord is not tangled pinched or otherwise deformed or is located near a source of heat as this could lead to its damage e Never place the appliance on the power cord The sharp edges of the appliance s feet may damage the power cord e Only use power cords that conform with the rated power of the appliance e Dono submerge the appliance in water or any other liquid e Protect the appliance from rain or other moisture Only the chilling compartment of the appliance may come into contact with liquids and only in exceptional circumstances e Operate the appliance if the electrical voltage on the label is the same as the electrical voltage in your power socket Incorrect electrical voltage may damage the appliance e Disconnect the appliance from the power socket if you are not using it e Check that there is no danger of tripping over the power cord d the appliance is damaged If the power cord of the appliance is damaged it must be replaced by the manufacturer or at an authorised service centre to prevent a risk of injury e If aliquid has entered into the appliance the appliance has fallen or has been damage in any other way it must be inspected at an authorised service centre Disconnect the appliance from the main source of electricity and contact an authorised service centre e Never repair a damaged part of the appliance or the appliance with a damaged power cord yourself There is a high risk of injury Safe operation
23. the following accessories e Keg adapter blue green Pic 2 13 e 1 air hose Pic 2 5 e 1 beer hose Pic 2 1 The 4 litre beer keg Pic 22 is offered by many European beer distributors Its fitting is compatible with the keg adapt er of the dispenser unit 1 Pull the overseal Pic 23 1 out of the keg and pull out the hose with plug Pic 23 2 You may throw these parts away Pic 23 Take out the beer hose Pic 24 1 from the keg adapter Pic 24 2 Place the adapter on to the keg Check that the fittings fit into each other one into the other Pic 25 A Check that keg adapter is firmly seated on the keg Open the lid of the appliance Pic 1 4 Pic 25 EN 12 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 6 Place two hose clamps on the bottom part of the beer wa tube Pic 26 1 These two clamps will later be used to secure the beer hoses on to the tap adapter Place the shorter end of the beer hose on to the beer tube Pic 27 1 Allow the hose clamps Pic 27 2 to gently slide on to the beer hose and the beer tube Attention Check that the beer hose is pushed far enough past the fitting A beer hose that is not pushed on far enough may come loose And this may result in the release of the pressurised liquid Gently push the tap handle Pic 28 1 downwards Insert the beer tube Pic 28 2 into the tap until its other end extends past the
24. the tap handle towards you and pour yourself a glass Pouring with the tap handle half open may result in a large amount of head being created 3 Release the tap handle at the right time to stop the pouring process 4 Pour another beer if necessary Note Regularly inspect the drip tray when pouring Pour out the contents of the drip tray If necessary and rinse it You may begin pouring beverages as soon as the keg is connected and the appliance is turned on Nonetheless we recommend that you wait until the liquid has reached the desired temperature Beer froths a lot when its temperature is too high Attention Do not store kegs with the bottom facing upwards they could tip over FEM Note The appliance is loud While the appliance is turned on the pump automatically starts when air pressure falls below the required level As soon as the correct pres sure is achieved the pump turns itself off automatically Ask your supplier about the optimum temperature for your beverage the correct type of glass and the typical pouring method for achieving optimal results EN 18 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 TAKING THE KEG OUT OF THE APPLIANCE If you are only pouring froth then the beer keg is empty and it is necessary to replace it If necessary you can also remove partially empty kegs 1 Turn off the appliance and disconnect it from the power socket 2 Hold a glass under the tap
25. w ready to be turned on see chapter Turning on and cooling EN 16 Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 TURNING ON AND COOLING Warning Turn on the appliance only once the kegs are properly connected see chapter In stalling a keg Check that no liquid has entered inside the appliance excluding the chilling compart ment If you find any liquid then under no circumstances should you turn the appliance on Contact your vendor or an authorised service centre for repairs Turning on 1 Check that the keg is correctly connected 2 Close the lid of the appliance Pic 1 4 3 First connect the power cord to the power socket on the appliance Pic 38 1 then connect it to the wall socket 4 Turn on the appliance using the On I Off O indicator light switch 38 2 Pic 38 Cooling 1 Use the temperature control dial Pic 38 3 to achieve the correct temperature Anticlockwise H Turn right Increase the temperature Clockwise L Turn left Decrease the temperature Note Setting the temperature using the temperature control dial has a fundamental ef fect on the temperature of the beverage It is necessary understand that cooling or heating the entire contents of the keg may take some time The temperature in the chilling compartment is shown on the temperature display 1 2 Q Note The temperature is measured outside of the keg and so it is possibl
26. y be damaged Never use kegs that are damaged or dinted in any way Copyright 2011 Fast CR a s Revision 1 2012 Beer Dispenser SBC 2318 The procedure for connecting individual keg types is described below e 5 litre beer keg e 4 litre beer keg e 6 litre beer keg 5 litre beer keg To connect the keg you will need the following acces sories e Keg adapter yellow Pic 2 15 e Tubing to the keg yellow Pic 2 6 e 1 air hose Pic 2 5 e 1 beer hose Pic 2 14 The 5 litre beer keg Pic 12 also called party keg is offered by many European beer distributors Is poured by means of the dispensing unit through ventilation open Pic 12 ings on the top side of the keg 1 Insert the yellow tubing into the yellow keg adapter Pic 13 and screw in firmly Pic 13 2 Move the lock Pic 14 1 to the Close position 3 First the pressure in the keg must be reduced Perform this by using the draught seal on the keg Follow the instructions on the keg 4 Pour 2 3 glasses of head froth until you register that the pressure in the keg has fallen significantly 5 Press the draught seal on the keg once more Pic 15 Copyright 2011 Fast CR as Revision 1 2012 Beer Dispenser SBC 2318 6 Remove the plug to open the keg opening Pic 16 A located at its top end 7 The keg opening has various designs depending on the type of keg therefore it is necessary to check whether the openin
Download Pdf Manuals
Related Search