Zanussi ZGO75524BA hob
Contents
1. All electrical connections should be made by a qualified electrician The appliance must be earthed Before carrying out any operation make sure that the appliance is disconnected from the power supply Make sure that the electrical information on the rating plate agrees with the power supply If not contact an electrician Make sure the appliance is installed correctly Loose and incorrect electricity mains cable or plug if applicable can make the terminal become too hot Use the correct electricity mains cable Do not let the electricity mains cable tangle Make sure that a shock protection is installed Use the strain relief clamp on the cable Make sure the mains cable or plug if applicable does not touch the hot appliance or hot cookware when you connect the appliance to the near sockets Do not use multi plug adapters and extension cables Make sure not to cause damage to the mains plug if applicable or to the mains cable Contact an Authorised Service Centre or an electrician to change a damaged mains cable The shock protection of live and insulated parts must be fastened in such a way that it cannot be removed without tools Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation If the mains socket is loose do not connect the mains plug Do not pull the mains cable to disconnect the appliance Always pull t2. Do not operate the appliance with wet hands or when it has contact with water Do not use the appliance as a work surface or as a storage surface When you place food into hot oil it may splash www zanussi com WARNING Risk of fire and explosion Fats and oil when heated can release flammable vapours Keep flames or heated objects away from fats and oils when you cook with them The vapours that very hot oil releases can cause spontaneous combustion Used oil that can contain food remnants can cause fire at a lower temperature than oil used for the first time Do not put flammable products or items that are wet with flammable products in near or on the appliance WARNING Risk of damage to the appliance Do not keep hot cookware on the control panel Do not let cookware to boil dry Be careful not to let objects or cookware fall on the appliance The surface can be damaged Do not activate the cooking zones with empty cookware or without cookware Do not put aluminium foil on the appliance Cookware made of cast iron aluminium or with a damaged bottom can cause scratches on the glass glass ceramic Always lift these objects up when you have to move them on the cooking surface Use only stable cookware with the correct shape and diameter larger than the dimensions of the burners Make sure the flame does not go out when you quickly turn the knob from the maximum to the minimum position Use only the ac
3. Domestic Gas Installation l S 813 Current Editions Table Four Location The hob may be located in a kitchen a kitchen diner or bed sitting room with a volume greater than 20 m8 but not in a bathroom or shower room The minimum distance combustible material can be fitted above the hob in line with the edges of the hob is 400 mm If it is fitted below 400 mm a space of 50 mm must be allowed from the edges of the hob For appliances installed in the Republic of Ireland please refer to NSAI Domestic Gas Installation I S 813 Current Edition Section 7 Permitted Locations of Appliance Gas Connection WARNING Any gas installation must be carried out by a GAS SAFE REGISTER installer Make sure that once the hob is installed it is easily accessible for the engineer in the event of a breakdown The manufacturer will not accept liability should the above instructions or any of the other safety instructions incorporated in this instruction booklet be ignored On the end of the shaft which includes the G 1 2 threaded elbow adjustment is fixed so that the washer is fitted between the components as shown in the diagram Screw the parts together without using excessive force gt A BC A End of shaft with nut B Washer C Elbow Connection to the gas supply should be with either rigid or semi rigid pipe i e steel or copper www zanussi com The connection should be suitable for connecting t
4. User Manual U S E R MANUAL Hob ZGO75524BA sa ZANUSSI Contents Safety information _ 2 Care and cleaning 8 Safety Instructions 3 Troubleshooting 9 Product description 6 Tnstallation za 10 Daily USE ennaa 6 Technical information 14 Hints anditipS ecs anak a d E 7 Subject to change without notice AA Safety information Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incorrect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Do not let children play with the appliance Keep all packaging away from children Keep children and pets away from the appliance when it operates or when it cools down Accessible parts are hot If the appliance has a child safety device we recommend you activate It Cleaning and user maintenance shall not be made by children without supervision Children o
5. and crown are placed Place the burner cap and crown incorrectly correctly The flame extinguishes immedi Thermocouple is not heated up After lightning the flame keep the ately after ignition sufficiently knob pushed for equal or less than 10 seconds The flame ring is uneven Burner crown is blocked with Make sure that the injector is not food residues blocked and the burner crown is clean If you cannot find a solution technician or dealer will not be free of charge also during the warranty period The instructions about the Service Centre and conditions of guarantee are in the guarantee booklet If you cannot find a solution to the problem yourself contact your dealer or an Authorised Service Centre Give the data from the rating plate Make sure you operated the hob correctly If not the servicing by a service www zanussi com 9 Labels supplied with the accessories bag Stick the adhesive labels as indicated below d A B Cc MOD MOD MOD TYPE PROD NO 230V 50Hz PROD NO PROD NO C 0049 SER NO B SER NO SER NO qa Ir DATA DATA MADE IN ITALY 1 1 1 1 l 1 1 1 1 MODEL MODEL al E 1 N A Stick it on Guarantee Card and send this part if applicable B Stick it on Guarantee Card and keep this part if applicable Installation WARNING Refer to Safety chapters Before the installation Before you install the hob write down the inf
6. age category Ill must be guaranteed The earth cable is excluded from this When you route the mains cable make sure that the cable doesn t come into direct contact for example using insulating sleeving with parts that can reach temperatures of more than 50 C above room temperature Safety Instructions This appliance is suitable for the following markets GB Installation WARNING Only a qualified person must install this appliance Remove all the packaging Do not install or use a damaged appliance www zanussi com Obey the installation instruction supplied with the appliance Keep the minimum distance from the other appliances and units Always be careful when you move the appliance because it is heavy Always wear safety gloves Seal the cut surfaces with a sealant to prevent moisture to cause swelling Protect the bottom of the appliance from steam and moisture Do not install the appliance adjacent to a door or under a window This prevents hot cookware to fall from the appliance when the door or the window is opened If the appliance is installed above drawers make sure that the space between the bottom of the appliance and the upper drawer is sufficient for air circulation The bottom of the appliance can get hot Make sure to install a non combustile separation panel under the appliance to prevent access to the bottom Electrical Connection WARNING Risk of fire and electrical shock
7. cessories supplied with the appliance Do not install a flame diffuser on the burner www zanussi com The use of a gas cooking appliance results in the production of heat and moisture Provide good ventilation in the room where the appliance is installed Prolonged intensive use of the appliance may call for additional ventilation for example opening of a window or more effective ventilation for example increasing the level of mechanical ventilation where present This appliance is for cooking purposes only It must not be used for other purposes for example room heating Care and cleaning Clean regularly the appliance to prevent the deterioration of the surface material Deactivate the appliance and let it cool down before you clean it Disconnect the appliance from the electrical supply before maintenance Do not use water spray and steam to clean the appliance Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abrasive products abrasive cleaning pads solvents or metal objects Do not clean the burners in the dishwasher Disposal WARNING Risk of injury or suffocation Contact your municipal authority for information on how to discard the appliance correctly Disconnect the appliance from the mains supply Cut off the mains cable and discard it Flat the external gas pipes Product description Cooking surface layout o o o CoH Contro
8. coloration Clean the hob with a moist cloth and some detergent After cleaning rub the hob dry with a soft cloth Wash stainless steel parts with water and then dry them with a soft cloth Pan supports To clean the enamelled parts cap and crown wash them with warm soapy water The pan supports are not resistant and dry them carefully before you put them to washing in a dishwasher They back must be washed by hand F Cleaning the spark plug 1 Remove the pan supports to easily clean j j j the hob This feature is obtained through a ceramic ignition candle with a metal electrode Keep these components well clean to prevent difficult lighting and check that the burner crown holes are not obstructed Be very careful when you replace the pan supports to prevent the hob top from damage 8 www zanussi com Periodic maintenance Speak to your local Authorised Service Centre periodically to check the conditions of the gas supply pipe and the pressure adjuster if fitted Troubleshooting WARNING Refer to Safety chapters What to do if There is no spark when you try to The hob is not connected to an Check if the hob is correctly con activate the spark generator electrical supply or itis connec nected to the electrical supply ted incorrectly The fuse is released Make sure that the fuse is the cause of the malfunction If the fuse releases again and again contact a qualified electrician Burner cap
9. dispose appliances marked with the symbol A with the household waste Return the product to your local recycling facility or contact your municipal office www zanussi com 15 www Zanussi com shop PN fN 867305000 B 102014
10. e pan on two burners AN WARNING Do not put unstable or damaged pots on the burners to prevent from spill and injury www zanussi com CAUTION In the absence of electricity you can ignite the burner without electrical device in this case approach the burner with a flame turn the control knob counter clockwise to maximum gas supply position and push it down Keep the control knob pushed for equal or less than 10 seconds to let the thermocouple warm up i If the burner accidentally goes out turn the control knob to the off position and try to light the burner again after minimum 1 minute i The spark generator can start automatically when you switch on the mains after installation or a power cut It is normal Turning the burner off To put the flame out turn the knob to the off position O WARNING Always turn the flame down or switch it off before you remove the pans from the burner AN CAUTION Make sure that the bottoms of pots do not stand above the control knobs otherwise the flame heats the control knobs up CAUTION Make sure that pot handles are not above the front edge of the cooktop gt CAUTION Make sure that the pots are placed centrally on the burners in order to get maximum stability and to get lower gas consumption AN CAUTION Liquids spilt during cooking can cause the glass to break gt Energy saving If itis possible always put the lids on the D
11. ety the installation must be done by a qualified electrician e g your local Electricity Board or a contractor who is on the roll of the National Inspection Council for Electrical Installation Contracting NICEIC 12 The manufacturer refuses to be held responsible if these safety measures are not abided by Supply connections This hob has to be connected to 230 240 V 50 Hz electricity supply The hob has a terminal block which is marked as follows L Live terminal N Neutral terminal ii or E Earth terminal Before carrying out the connection make sure 1 The limiter valve and the electrical system can take the appliance load see the rating plate 2 The supply system is equipped with an efficient earth connection in compliance with the current standards and regulations 3 The outlet or omnipolar switch used for connection is easily accessible with the appliance installed The appliance is supplied with a 3 core flexible power cable with a 3 amp plug If it is necessary to change the fuse use a 3 amp ASTA approved BS 1362 fuse d N A Green and Yellow B 3 amp fuse C Brown D Cord clamp E Blue The wires in the cord are coloured as follows www zanussi com Green and yellow Earth Blue Neutral Brown Live WARNING A cut off plug inserted into a 13 amp socket is a serious shock hazard Ensure that the cut off plug is disposed of safel
12. f less than 3 years should be kept away unless continuously supervised General Safety The appliance and its accessible parts become hot during use Do not touch the heating elements Do not operate the appliance by means of an external timer or separate remote control system 2 www zanussi com Unattended cooking on a hob with fat or oil can be dangerous and may result in fire Never try to extinguish a fire with water but switch off the appliance and then cover flame e g with a lid or a fire blanket Do not store items on the cooking surfaces Metallic objects such as knives forks spoons and lids should not be placed on the hob surface since they can get hot Do not use a steam cleaner to clean the appliance If the glass ceramic surface glass surface is cracked switch off the appliance to avoid the possibility of electric shock In case of hotplate glass breakage shut immediately off all burners and any electrical heating element and isolate the appliance from the power supply do not touch the appliance surface do not use the appliance If the supply cord is damaged it must be replaced by the manufacturer an authorized Service or similarly qualified persons in order to avoid a hazard Where the appliance is directly connected to the power supply an all pole isolating switch with a contact gap is required Complete disconnection in compliance with the conditions specified in overvolt
13. he mains plug Use only correct isolation devices line protecting cut outs fuses screw type fuses removed from the holder earth leakage trips and contactors The electrical installation must have an isolation device which lets you disconnect the appliance from the mains at all poles The isolation device must have a contact opening width of minimum 3 mm Gas connection All gas connections should be made by a qualified person Before installation make sure that the local distribution conditions nature of the gas and gas pressure and the adjustment of the appliance are compatible Make sure that there is air circulation around the appliance The information about the gas supply is on the rating plate This appliance is not connected to a device which evacuates the products of combustion Make sure to connect the appliance according to current installation regulations Pay attention to requirements regarding adequate ventilation Use WARNING Risk of injury burns and electrical shock Remove all the packaging labelling and protective film if applicable before first use Use this appliance in a household environment Do not change the specification of this appliance Make sure that the ventilation openings are not blocked Do not let the appliance stay unattended during operation Set the cooking zone to off after each use Do not put cutlery or saucepan lids on the cooking zones They can become hot
14. iameter of cookware cookware When the liquid starts to boil turn down the mm flame to barely simmer the liquid Semi rapid rear left 120 240 Diameters of cookware RT i Semi rapid rear right 120 240 Use cookware with diameters wee applicable to the size of burners Semi rapid front left 0229 Auxiliary 80 180 Diameter of cookware mm Triple Crown 180 260 Care and cleaning WARNING 2 The enamel coating occasionally can have Refer to Safety chapters rough edges so be careful when you wash the pan supports by hand and dry them If necessary remove stubborn stains with a General information paste cleaner Clean the hob after each use 3 After you clean the pan supports make sure Always use cookware with clean bottom that they are in correct positions Scratches or dark stains on the surface have 4 For the burners to operate correctly make no effect on how the hob operates sure that the arms of the pan supports are Use a special cleaner applicable for the aligned with the centre of the burner surface of the hob WARNING Cleaning the hob Do not use knives scrapers or Remove immediately melted plastic similar instruments to clean the plastic foil and food with sugar If not the surface of the glass or between the dirt can cause damage to the hob rims of the burners and the frame if Remove when the hob is sufficiently applicable cool limescale rings water rings fat stains shiny metallic dis
15. ifferent from the necessary pressure you must fit an applicable pressure adjuster on the gas supply pipe 11 Adjustment of minimum level To adjust the minimum level of the burners Light the burner Turn the knob on the minimum position Remove the knob With a thin screwdriver adjust the bypass screw position A A POs A i N If you change from natural gas G20 20 mbar to liquid gas fully tighten the bypass screw in from liquid gas to natural gas G20 20 mbar undo the bypass screw approximately 1 4 of a turn 1 2 of a turn for Triple Crown burner AN WARNING Make sure the flame does not go out when you quickly turn the knob from the maximum position to the minimum position Electrical connection Do not pull the mains cable to disconnect the appliance Always pull the mains plug if applicable The appliance must not be connected with an extension cable an adapter or a multiple socket There is a risk of fire Do not let the power cable to heat up to a temperature of more than 90 C The cable should be guided by means of clamps fixed to the side of the cabinet in order to avoid any contact with the equipment beneath the cooktop Make sure that there is access to the mains plug after the installation Electrical Requirements Permanent electrical installation must agree with the latest I E E Regulations and local Electricity Board regulations For your own saf
16. l knob no gas supply off position Daily use WARNING Refer to Safety chapters Burner overview b Semi rapid burner Triple Crown burner Auxiliary burner Control knobs ame IC N ignition position maximum gas supply minimum gas supply A Burner cap B Burner crown C Ignition candle D Thermocouple www zanussi com Ignition of the burner Always light the burner before you put on the cookware WARNING Be very careful when you use open fire in the kitchen environment The manufacturer declines any responsibility in case of the flame misuse 1 Push the control knob down and turn it counterclockwise to the maximum gas supply position 0 2 Keep the control knob pushed for equal or less than 10 seconds This lets the thermocouple warm up If not the gas supply is interrupted 3 Adjust the flame after it is regular If after some tries the burner does not light check if the crown and its cap are in correct positions AN WARNING Do not keep the control knob pushed for more than 15 seconds If the burner does not light after 15 seconds release the control knob turn it into off position and try to light the burner again after minimum 1 minute Hints and tips WARNING Refer to Safety chapters Cookware AN CAUTION Do not use cast iron pans potstones earthenware grill or toaster plates AN WARNING Do not put the sam
17. o R 1 2 1 2 BSP male thread When the final connection has been made it is essential that a thorough leak test is carried out on the hob and installation Make sure that the main connection pipe does not exert any strain on the hob If you use flexible metal pipes make sure that they agree to ISO 10380 and ISO 10807 standards Be careful they do not come in touch with mobile parts or they are not squeezed Also be careful when the hob is put together with an oven CAUTION It is important to install the elbow correctly with the shoulder on the end of the thread fitted to the hob connecting pipe AN CAUTION Failure to ensure the correct assembly will cause leakage of gas AN CAUTION Make sure that the gas supply pressure of the appliance obeys the recommended values Rigid connection Carry out connection by using metal rigid pipes copper with mechanical end Injectors replacement 1 Remove the pan supports 2 Remove the caps and crowns of the burner 3 With a socket spanner 7 remove the injectors and replace them with the ones which are necessary for the type of gas you use see table in Technical Information chapter 4 Assemble the parts follow the same procedure backwards 5 Replace the rating plate it is near the gas supply pipe with the one for the new type of gas supply You can find this plate in the package supplied with the appliance If the supply gas pressure is changeable or d
18. onnections Kitchen unit with oven jar mm The electrical connection of the hob and the oven must be installed separately for safety A reasons and to let easy remove oven from the unit min 20 mm max 150 mm N sA Technical information Hob dimensions Width 740 mm Depth 510 mm Bypass diameters BURNER BYPASS 1 100 mm Triple Crown 56 Semi rapid 82 Auxiliary 28 Other technical data Gas original G20 2H 20 mbar 10 5 kW TOTAL POWER Gas replacement G30 3 28 30 mbar 763 g h G31 3 37 mbar 750 g h Electric supply 230 V 50 Hz 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse Appliance category IIZH3 Gas connection R24 Appliance class 3 14 _ www zanussi com Gas burners for NATURAL GAS G20 20 mbar BURNER NORMAL POWER kW MINIMUM POWER kW INJECTOR MARK 1 100 mm Triple Crown 3 8 1 4 146 Semi rapid 1 9 0 45 96 Auxiliary 1 0 0 33 70 Gas burners for LPG G30 G31 28 30 37 mbar BURNER NORMAL MINIMUM INJECTOR NOMINAL GAS FLOW g h POWER POWER MARK 1 100 kW kW mm G30 28 30 G31 37 mbar mbar Triple Crown 3 8 1 4 98 276 271 Semi rapid 1 9 0 45 71 138 136 Auxiliary 1 0 0 33 50 73 71 ENVIRONMENTAL CONCERNS Recycle the materials with the symbol Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not
19. ormation bellow from the rating plate The rating plate is on the bottom of the hob Important safety requirements This hob must be installed in accordance with the Gas Safety Installation and Use Regulations Current Edition and the IEE Wiring Regulations Current Edition For appliances installed in the Republic of Ireland please refer to NSAI Domestic Gas Installation I S 813 Current Editions and the ETCI Rules for Electrical Installations 10 C Stick it on instruction booklet Provision for ventilation Detailed recommendations are contained in the following British Standards Codes Of Practice B S 6172 B S 5440 Par 2 and B S 6891 Current Editions The hob should not be installed in a bed sitting room with a volume of less than 20 m If it is installed in a room of volume less than 5 m3 an air vent of effective area of 100 cm is required If it is installed in a room of volume between 5 m3 and 10 m8 an air vent of effective area of 50 cm is required while if the volume exceeds 1 1 m8 no air vent is required However if the room has a door which opens directly to the outside no air vent is required even if the volume is between 5 m3 and 11 m8 If there are other fuel burning appliances in the same room B S 5440 Part 2 Current Edition should be consulted to determine the requisite air vent requirements www zanussi com For appliances installed in the Republic of Ireland please refer to the NSAI
20. y Replacement of the connection cable i The replacement of electric cable must be carried out exclusively by the service force centre or by personnel with similar competencies in accordance with the current regulations i To replace the connection cable use only HO5V2V2 F T90 or equivalent type Make sure that the cable section is applicable to the voltage load and the working temperature The yellow green earth wire B must be approximately 2 cm longer than the live and neutral wire A A B 1 Connect the green and yellow earth wire to the terminal which is marked with the letter E or the earth symbol or coloured green and yellow 2 Connect the blue neutral wire to the terminal which is marked with the letter N or coloured blue 3 Connect the brown live wire to the terminal which is marked with the letter L It must always be connected to the network phase There must be no cut or stray strands of wire present The cord clamp must be correctly attached to the outer sheath www zanussi com Building In A supplied seal B supplied brackets CAUTION Install the appliance only on a worktop with flat surface Possibilities for insertion Kitchen unit with door The panel installed below the hob must be easy to remove and let an easy access in case a technical assistance intervention is necessary 13 a N A Removable panel B Space for c
Download Pdf Manuals
Related Search