Powerplus POWX0460 power sander
Contents
1. Acceptance of claims under warranty can never lead to the prolongation of the warranty period nor commencement of a new warranty period in case of a device replacement Copyright 2014 VARO Page 7 www varo com POWERPLUS POWX0460 EN HIGH QUALITY TOOLS Devices or parts which are replaced under the warranty therefore remain the property of Varo NV We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained Clean ventilation slots carbon brushes serviced regularly etc Your purchase receipt must be kept as proof of date of purchase Your appliance must be returned undismantled to your dealer in an acceptably clean state in its original blow molded case if applicable to the unit accompanied by proof of purchase 14 ENVIRONMENT D Should your appliance need replacement after extended use do not discard it with the household rubbish but dispose of it in an environmentally safe way Waste produced by electrical machine items should not be handled like normal household rubbish Please recycle where recycle facilities exist Check with your Local Authority or retailer for recycling advice 15 DECLARATION OF CONFORMITY VARO N V Joseph Van Instraat 9 BE2500 Lier BELGIUM declares that Product Belt Sander trade mark POWERplus model POW X0460 is in conformity with the essential requirements and other relevant provisio2. electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock f operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 5 3 Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used whenever conditions require will reduce personal injuries Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents Remove any adjustin
3. work area Whenever possible use a vacuum extractor for dust collection Remove dust and other waste matter in an environmentally safe way Always secure the work piece by clamps or else to avoid slipping away Do not leave the tool running Operate the tool only when handheld Ventilate your work area adequately when you perform sanding operations Be sure that there are no cracks or breakage in the belt before use Cracks or breakage may cause a personal injury AN Never use the machine for sanding magnesium workpieces Copyright 2014 VARO Page 4 www varo com POWERPLUS POWX0460 EN 7 OPERATION AN Do not sand plaster surfaces WARNING In this case your guarantee becomes void this may clog the motor brushes ball bearings 7 1 Switching Onoff To switch the tool on press the on off switch To switch the tool off release the on off switch 7 2 Continuous operation ON OFF lock button to switch on Hold the on off switch pressed Press the lock button release the on off switch to switch off press the on off switch once to release the lockon button 7 3 Speed adjusting dial Your POW X0460 is equipped with a variable speed selector You can turn the speed selector switch from 1 to 6 to set the desired belt speed 7 4 Mounting a sanding belt Pull out the locking lever in the side of the belt sander to loosen the sanding belt Take a sanding belt of the required grain size and place it on the
4. E The sander is used to sand and buff wood plastic and similar materials It is very important to use the correct sandpaper It is not designed for commercial use own safety Your power tool should only be passed on with these WARNING Read this manual carefully before using the machine for your instructions DESCRIPTION Front cover 7 Connector for dust collection box Auxiliary handle 8 Adjusting screw Speed control dial 9 Dust collection box Lock on button 10 Locking lever for auxiliary handle Main handle 11 Sanding Belt ON OFF switch 12 Locking lever PACKAGE CONTENT LIST Remove all packing materials Remove remaining packaging and transit supports if existing Check the completeness of the packing content Check the appliance the power cord the power plug and all accessories for transportation damages Keep the packaging materials as far as possible till the end of the warranty period Dispose it into your local waste disposal system afterwards PR Fb OaRWONM gt WARNING Packing materials are no toys Children must not play with plastic bags Danger of suffocation 3 pcs sanding belt grain 60 80 120 1 dust box with micro filter i When parts are missing or damaged please contact your dealer 4 SYMBOLS In this manual and or on the machine the following symbols are used Denotes risk of personal injury Wear a mask In dusty or damage to the tool conditions In accordance with essential require
5. POWERPLUS HIGH QUALITY TOOLS POWX0460 EN 1 ooo RE 2 2 E 2 3 PACKAGE CONTENT LIST 2 sceccsesseeccensseecensseeeeeneeeees 2 4 E E 2 5 GENERAL POWER TOOL SAFETY WARNINGS 5 3 5 1 WOW NCE tege eenegen 3 5 2 ICCIIICAL Salet cerra EErEE araa 3 5 3 EELER 3 5 4 Power lool USC and Car ssiscciecarinicisnatectecenieiecsendecisianteitinntecteseateteernicnirenntertsectec 4 55 SEVICE orsina aA eer ere eee eee ee eae meee 4 6 ADDITIONAL SAFETYHINTS FOR BELT SANDERG 4 7 O 5 7 1 SEET 5 7 2 Continuous operation ON OFF lock DUttON ccccccccccceeenennensnneseseneeeeeeeeeeeennaneneess 5 7 3 SDECO adjusiing E 5 7 4 MOUNTING a sanding Delt ccccneeeccccccccennneneceneeennannnesseeennnanensseeennaasnseeeeenansnssseeenaans 5 7 5 CONECUING the E 5 7 6 Auxiliary handle position AAJUSKIMEN ccccceeeeccccceeeennnneeseeeeenanneneseeeennnnessseeenaneneees 5 8 CLEANING AND MAINTENANCE ccssseeesssseeeeeeneeeeeees 6 8 1 CLC e e ON 6 H Coo o 6 10 E ecsaaesus aiwnntat Just sseeavauttesseceorsienceutaesscteranaeaeteasaeaversnns 7 11 SERVICE DEPARTMENT eerie T 12 o xd row cate anyeneleaenctsccessuncricamcuncdisyewsteeactugustiwesuacecsniviawecoans 7 13 I H T 14 1 EE 8 15 DECLARATION OF CONFORMITY cccccssseeecesseeeseenseeees 8 Copyright 2014 VARO Page 1 www varo com POWERPLUS POWX0460 EN HIGH QUALITY TOOLS BELT SANDER POWX0460 1 APPLIANC
6. g key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewelry Keep your hair clothing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Copyright 2014 VARO Page 3 www varo com POWERPLUS POWX0460 EN HIGH QUALITY TOOLS f devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards 5 4 Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to ope
7. ments of the European Read manual before use directive s Class Il The machine is double insulated Earthing wire G Wear eye protection is therefore not necessary Copyright 2014 VARO Page 2 www varo com POWERPLUS POWx0460 EN 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool 5 1 Work area Keep work area clean and well lit Cluttered and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 5 2 Electrical safety Always check that the power supply corresponds to the voltage on the rating plate Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of
8. ns of the applicable European Directives based on the application of European harmonized standards Any unauthorized modification of the apparatus voids this declaration European Directives including if applicable their amendments up to the date of signature 2011 65 EU 2006 42 EC 2004 108 EC European harmonized standards including if applicable their amendments up to the date of signature EN60745 1 2009 EN60745 2 4 2009 EN55014 1 2006 EN55014 2 1997 EN61000 3 2 2006 EN61000 3 3 2008 Keeper of the Technical Documentation Philippe Vankerkhove VARO Vic Van Rompuy N V The undersigned acts on behalf of the company CEO VA Philippe Vankerkhove Regulatory Affairs Compliance Manager 24 06 13 Copyright 2014 VARO Page 8 www varo com
9. ol ammonia water etc These solvents may damage the plastic parts 9 TECHNICAL DATA Mains voltage frequency 230 240V 50Hz Power rating 950W Variable speed 0 380 m min belt size 533 x 76mm Sanding surface 170 x 75 mm Weight 6 kg Copyright 2014 VARO Page 6 www varo com POWERPLUS HIGH QUALITY TOOLS POWX0460 EN 10 NOISE Noise emission values measured according to relevant standard K 3 Acoustic pressure level LpA 90 dB A Acoustic power level LwA 101 dB A ATTENTION Wear hearing protection when sound pressure is over 85 d dB A aw Vibration Max 5 1 m s K 1 5 ms wear suitable eye respiration hand amp hearing protection when working L 1 SERVICE DEPARTMENT Damaged switches must be replaced by our after sales service department If the connecting cable or mains plug is damaged it must be replaced by a particular connecting cable which is available from our service department Replacement of the connecting cable must only be carried out by our service department see last page or by a qualified person qualified electrician SS STORAGE Thoroughly clean the whole machine and its accessories Store it out of the reach of children in a stable and secure position in a cool and dry place avoid too high and too low temperatures Protect it from exposure to direct sunlight Keep it in the dark if possible Don t keep it in plastic bags to avoid humidity build up WARRANTY This produc
10. rate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or sticking of moving parts breakage of parts and any other condition that may affect the power tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to stick and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could lead to a hazardous situation 5 5 Service Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained 6 ADDITIONAL SAFETYHINTS FOR BELT SANDERS AN Always wear safetygoggles and a dustmask during your work with the sander Observe the applicable regulations when sanding painted surfaces Take special care when sanding lead based paint Al persons entering the work area must wear a mask specially designed for protection against lead paint dust and fumes Children and pregnant women must not enter the work area Do not eat drink or smoke in the
11. rollers Make sure that the arrow on the inside of the sanding belt points in the same direction as the arrow on the machine Make sure that the sanding belt is straight and centered on the rollers Push the clamping lever back Switch the machine on to let the sanding belt run With the machine switched on turn the adjusting screw until the sanding belt keeps running straight A The sanding belt must be fitted firmly on the sanding pad and should not come loose 7 5 Collecting the dust dust box Push and slide the dust collection box into the connector for dust collection Make sure the grooves on the right and left of the connector are into place and it is secured before starting the operation 7 6 Auxiliary handle position adjustment Pull out the lock on the right of the handle and rotate in desired position Put the lock back in place by pushing towards handle Copyright 2014 VARO Page 5 www varo com POWERPLUS POWX0460 EN HIGH QUALITY TOOLS 0 8 CLEANING AND MAINTENANCE AN Attention Before performing any work on the equipment pull the power plug 8 1 Cleaning Keep the ventilation slots of the machine clean to prevent overheating of the engine Regularly clean the machine housing with a soft cloth preferably after each use Keep the ventilation slots free from dust and dirt Ifthe dirt does not come off use a soft cloth moistened with soapy water Never use solvents such as petrol alcoh
12. t is warranted for a 36 month period effective from the date of purchase by the first user This warranty covers all material or production flaws excluding batteries chargers defective parts subject to normal wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc damage or defects resulting from maltreatment accidents or alterations nor the cost of transportation Damage and or defects resulting from inappropriate use also do not fall under the warranty provisions We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Repairs may only be carried out by an authorised customer service centre for Powerplus tools You can always obtain more information at the number 00 32 3 292 92 90 Any transportation costs shall always be borne by the customer unless agreed otherwise In writing At the same time no claim can be made on the warranty if the damage of the device is the result of negligent maintenance or overload Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inappropriate usage use for purposes for which the device is not suitable incompetent usage e g not following the instructions given in the manual inexpert assembly lightning strike erroneus net voltage This list is not exhaustive
Download Pdf Manuals
Related Search