Home

Bosch WAE28377GB washing machine

image

Contents

1. Register your new Bosch now www bosch home com welcome Washing machine WAE28377GEB en Instruction Manual and Installation Instructions Your new washing machine You have chosen a Bosch washing machine Please take a few minutes to read and become familiar with the advantages of your washing machine To meet the high quality demands required by Bosch every washing machine that leaves our factory is carefully checked to ensure that it functions correctly and Is in perfect condition For more information on our products accessories replacement parts and services see our website www bosch home com or contact our after sales service centres lf the operating and installation instructions describe different models any differences will be pointed out at the relevant points in the text an Read these operating and installation instructions before switching on the washing machine Display rules A Warning This combination of symbol and signal word indicates a possibly dangerous situation Not heeding the warning can Cause death or injuries Caution This signal word indicates a possibly dangerous situation Not heeding the caution can cause property and or environmental damage Note tip Information about the optimum use of the appliance any other useful information 1 2 3 a b The steps are represented by numbers or letters a Lists are represented
2. select the function sev ume eral times rw AL w IO Caution Cleaning and Damage to the appliance maintenance Cleaning agents that contain solvents e g cleaning solvent can damage A w Surfaces and components in the sa Warning machine Risk of death Do not use cleaning agents that contain There is a risk of electric shock if you solvents touch live components Switch off the appliance and unplug the mains plug Machine housing control panel Z Warning Risk of poisoning a Wipe the housing and the control Toxic vapours can be produced by panel with a soft damp cloth cleaning agents that contain solvents a Do not use any abrasive cloths e g cleaning solvent scourers or cleaning agents Do not use cleaning agents that contain stainless steel cleaners solvents m Remove the detergent residue immediately 20 m Cleaning with a jet of water is prohibited Drum Wipe the inside of the rubber seal dry with a cloth Leave the washing machine door open in order that the drum can dry Use chlorine free cleaning agents and not steel wool Descaling Note Make sure that there is no laundry in the machine Descaling should not be necessary if the detergent is measured out correctly However if it is required follow the manufacturer s instructions for the descaling agent Suitable descalers can be obtained via our website or from our after sales service Detergent drawer and housing If the
3. residual moisture in the laundry slightly increased Rinse plus Extra rinse For areas with very soft water or to further improve the rinsing result amp Water plus Increased water level and additional rinse cycle extended washing time For areas with very soft water or to further improve the rinsing result depending on model Operating the appliance Preparing the washing machine Note The washing machine must be correctly installed and connected from Page 29 Connect the mains plug Turn on the water tap Open the washing machine door Check that the drum is completely drained Drain if necessary na a aa Operating the appliance en Select programme switch on the appliance Note If you have activated the childproof lock you must first deactivate it before you can set a programme Page 17 Use the programme selector to select the required programme Can be turned in both directions The machine is switched on The programme duration appears on the display panel Change the programme default settings You can use the default settings or change them To do this repeatedly press the corresponding button until the required setting is displayed Note All buttons are sensitive and only need to be touched lightly If the buttons are held for longer the appliance automatically runs through the setting options The settings are activated without needing to be co
4. Compartment Softener starch Do not exceed the maximum Compartmentl Detergent for prewash 1 Pull out the detergent drawer as far as possible 2 Add detergent and or care products 3 Close the detergent drawer Measuring aid for liquid detergent Depending on the model Position the measuring aid for measuring the correct amount of liquid detergent 1 Pull out the detergent drawer Press down the insert and fully remove the drawer 2 Slide the measuring aid forwards fold it down and click it into place 3 Reinsert the drawer Operating the appliance en Note Do not use the measuring aid for gel detergents and washing powder or for programmes with prewash or when the Finished in time is selected For models without a measuring aid pour the liquid detergent into the appropriate dispenser and place it in the drum Start the programme Select the Start Reload button The indicator lamp lights up and the programme starts During the programme the display panel shows the Finished in time or after starting the wash programme the programme duration and the symbols for the programme progress Page 9 Note If you want to lock the programme to prevent it from being inadvertently adjusted you can select the childproof lock as follows Childproof lock You can lock the washing machine to prevent the functions you have set from being changed inadvertently To do this activa
5. an electric valve Observe the following when connecting the machine Notes Only operate the washing machine using cold mains water m Do not connect the machine to the mixer tap of an unpressurised hot water boiler Do not use a used supply hose Only use the supply hose supplied or one that was purchased from an authorised specialist retailer m Do not bend squash modify or cut through the water supply hose otherwise its strength is no longer guaranteed m Only tighten the screw connections by hand If the screw connections are tightened too much with a tool pliers the thread may be damaged Optimum water pressure in the supply network At least 100 kPa 1 bar Maximum 1000 kPa 10 bar When the tap is open the water flow is at least 8 l min lf the water pressure is higher than this a pressure reducing valve must be installed Connection Connect the water supply hose to the water tap 26 4 mm and to the appliance not necessary for Aqua Stop models as this is permanently installed 32 Model Standard Note Open the water tap carefully checking the leak tightness of the connection points The screw connection is under mains water oressure Water outlet Caution Water damage lf the drain hose slips out of the wash basin or the connection point during draining due to high water pressure any escaping water may cause water damage Secure the
6. genuine spare parts 26 Consumption rates en Consumption rates Energy and water consumption programme duration and residual moisture for the main washing programmes Programme Energy consumption Water Programme duration Cottons 20 C kg 0 31 kWh Z 2 Ja h Cottons 40 C 1KO 0 85 kWh 12 2 Ja h Cottons 60 C 7kg 1 21 kWh 72 2 ah Cottons 90 C KO 2 01 kWh l 3h Easy Care 40 C 3 kg 0 04 kWh 56 1 4h Mixed Load 40 C 3 kg 0 46 kWh 36 Tan Delicate Silk 30 C 2 kg 0 24 kWh at 34 h 2 Wool 30 C 2 kg 0 22 kWh 47 34 h Programme Approximate information on the residual moisture WAE28 WAE24 WAE20 WAE16 max 1400 rpm max 1200rpm max 1000rpm max 800 rpm Cottons a 08 68 80 Easy Care 40 40 40 40 Delicate Silk 30 30 30 30 Wool 45 45 45 45 The values may deviate from the stated values depending on the following factors water pressure and hardness water inlet temperature ambient temperature type amount and soiling of laundry type of detergent used fluctuations in the power supply and additional functions selected Information on residual moisture based on programme dependent spin speed limits and maximum loads 2T en Technical data Efficiency test programmes for cotton fabrics The following programmes standard programmes indicated by lt _ are suitable for cleaning normally soiled cotton fabrics and are the most efficient with respect to combine
7. not cover defective feed lines or fittings leading to the Aqua Stop connection at the tap 4 Appliances with Aqua Stop do not need to be supervised during operation nor secured afterwards by turning off the tap The tap only needs to be turned off if you are away from home for a long period e g for several weeks holiday TE Advice and repair order in the event of faults GB 0344 892 8979 Calls charged at local or mobile rate IE 01450 2655 0 03 per minute at peak Off peak 0 0088 per minute You can find the contact information for all countries in the attached after sales service directory Robert Bosch Hausgerate GmbH Carl Wery StraBe 34 81739 Munchen DEUTSCHLAND 9001021005 9409
8. programme selector Programme type of laundry information Settings Name of the programme Max load Brief explanation of the programme and for which fabrics it is suita Reduced load for the Speed ble setting Temperature that can be selected spin speed that can be selected Max spin speed depending on the model Possible programme settings 48 Cottons Max 7 kg 4 kg Hard wearing fabrics heat resistant fabrics made of cotton or linen 20 30 40 60 90 C 4 Cottons 40 C Prewash Programme with prewash prewash w _ 1400 rom at 30 C divide detergent between compartments and Il j 0 Aw Note The Speed setting is suitable as a short programme for a lightly soiled laundry 4 Easy Care Max 3 kg Textiles made of synthetic materials or blended fabrics 210 AOE es WAU Fon A w I t Mixed Load Max 3 kg A mixed load of fabrics made of cotton and synthetic fabrics Oe Notes wae 00 ipm m Different types of laundry can be washed together m Mixed Load 40 C with maximum spin speed is ideal as a short programme 0 A w s Delicate Silk Max 2 kg For delicate washable fabrics e g made of silk satin synthetic eae fibres or blended fabrics e g silk blouses silk scarves Notes w 800 rom m Use a detergent which is suitable for machine washing delicates 0 A w b or silk m No spin cycle between the rinse cycles 12 Overview of programmes en Programme type of la
9. the laundry 2 Turn the programme selector to Off Appliance is switched off 3 Turn off the water tap Note Not required for Aqua Stop models Notes Do not leave any items of laundry in the drum They may shrink in the next wash or discolour another item m Remove any foreign objects from the drum and the rubber seal risk of rusting m Leave the washing machine door and detergent drawer open so that any residual water can dry away Sensors en Sensors Automatic load sensing The automatic load sensing function adapts the water consumption ideally to each programme depending on the type of fabric and the load Unbalanced load detection system The automatic unbalanced load detection system detects imbalances and ensures even distribution of the laundry by repeatedly starting and stopping drum spinning If the laundry is extremely unevenly distributed the speed is reduced or the spin cycle is not performed for safety reasons Note Place large and small items of laundry in the drum from gt Page 24 19 en Setting the signal Ed Setting the signal 1 Activate the setting mode for the signal volume CUP a BAE AGA CIPS Set to One step the display Select and hold One step release panel lights up 2 Set the volume for the button signals and information signals depending on the model E eal you may need to Set the vol skip One step Set the volume Set to
10. 28 Positioning and connecting 29 Included with the appliance 29 Safety instructionSs 29 Installation Surface 0 30 Installation on a base or a wooden JOIST TOG bos cane tine eee ek de ark 30 Installing the appliance in a kitchenette 000 30 Removing the transport locks 30 Hose and cable lengths 31 Water inlet 000 32 Water outlet 0 0008 32 Levelling 00 cee eee eee 33 Electrical connection 34 Before washing for the first time 34 Transportation 00004 35 Intended use For private domestic use only m he washing machine is suitable for washing machine washable fabrics and hand washable wool in detergent solution m o be operated with cold mains water and standard detergents and care products which are suitable for use in washing machines m When measuring the amount of all detergents additives care products and cleaning agents always check the manufacturer s instructions m he washing machine may be used by children over the age of 8 years old and by persons with reduced physical sensory or mental capacity or by persons with a lack of experience or knowledge if they are supervised or have been instructed by a responsible person Children must not carry out any cleaning or maintenance work without supervision m Keep pets away from the washing machine Read the Instruction Manual and Ins
11. Allow the programme to run for approximately 40 seconds 4 Turn the programme selector to Off Pull out the mains plug 5 Clean the filter on the water tap Remove the hose from the water tap Clean the filter with a small brush ih LL i o Pr 6 For standard and Aqua Secure models clean the filter on the rear of the appliance Remove the hose from the rear of the appliance Remove the filter using pliers and clean the filter i AENEAN 7 Connect the hose and check for leaks Faults and what to do about them Emergency release E g in the event of a power cut The programme will continue running when the power supply has been restored However if the laundry has to be removed the washing machine door can be opened as follows Z Warning Risk of scalding When you are washing at high temperatures there is a risk of scalding if you come into contact with hot detergent solution and laundry Faults and what to do about them en If possible leave it to cool down Z Warning Risk of injury You may injure your hands if you reach into the drum while it is rotating Do not reach into the drum while it is rotating Wait until the drum has stopped rotating Caution Water damage Any escaping water may cause water damage Do not open the washing machine door if water can be seen through the glass 1 Switch off the appliance Pull out the main
12. Caution Damage to the appliance he machine is secured for transportation using transport locks If the transport locks are not removed the drum for example may become damaged when the machine is operated Before using the appliance for the first time make sure that you completely remove all four transport locks Keep the locks in a safe place m o prevent transport damage from occurring if the appliance is moved at a later date you must refit the transport locks before transporting the appliance Note Store the screw and sleeve screwed together Positioning and connecting en Hose and cable lengths m Left hand connection 2 Unscrew and remove all four transport brace screws e Remove the sleeves To do this me l O remove the mains cable from the 145 cm3 T holders 90cm pa J N T5 mS S 140 cm Z gt Ele 3 Fit the covers Lock the covers firmly in place by applying pressure to the Tip snap in hooks The following are available from specialist dealers the after sales service m Extension for Aqua Stop and cold water supply hose approx 2 50 m Order no WMZ2380 WZ10130 Z10 70X0 A longer supply hose approx 2 20 m for standard model 31 en Positioning and connecting Water inlet Warning Risk of death There is a risk of electric shock if you touch live components Do not immerse the Aqua Stop safety valve in water it contains
13. amme selection in h min hours minutes 1 24h Finished in Programmes ends after h h hours Status indicators for the programme progress programme sequence gt amp w Childproof lock washing rinsing spinning Finished in Programme ends after 1 24 h en Laundry Laundry Sorting laundry Sort your laundry according to the care instructions and manufacturer s information on the care labels depending on Type of fabric fibre m Colour Note Laundry can discolour or not be cleaned correctly Wash white and coloured laundry separately Wash new bright fabrics separately the first time you wash them m Soiling Wash laundry with the same level of soiling together You can find examples of levels of soiling on Page 11 Light Do not pre wash select the Speed setting if necessary Normal Heavy Load less laundry select a programme with pre wash Stains Remove pretreat stains while they are fresh First dab the stain with soapy water do not rub Then wash the items of laundry with the appropriate programme Stubborn dried in stains can sometimes only be removed with several washes m Symbols on the care labels The numbers in the symbols indicate the maximum washing temperature which may be used YX Suitable for a normal washing process e g Cottons programme Y i A gentle washing process is required e g Easy Care programme Y An especially gent
14. ap not turned on Washing machine door cannot be opened Programme does not Start Detergent solution is not drained Water not visible in the drum 24 Filter blocked Clean the screen gt Page 22 supply hose kinked or trapped safety function active Programme stopped gt Page 18 without final spin selected Can be opened by emergency release only gt Page 23 Start Reload or Finished in time selected Washing machine door closed c Childproof lock activated Deactivate gt Page 17 w without final spin selected Clean detergent solution pump gt Page 21 Clean the waste pipe and or drainage hose Not a fault water below the visible area Faults Faults and what to do about them en Cause remedial action Spin result not satisfac tory Laundry wet too damp opin cycle started and Stopped several times The programme duration is longer than usual The programme duration changes during the wash cycle Residual water in the compartment for care products Odours in the washing machine The symbol flashes in the display panel Foam may escape from the detergent drawer Intense noise vibrations and wandering during spinning Noises during spin and drain cycles Display panel indicator lamps do not function dur m ing operation Detergent residues onthe m laundry NO appears on the dis play in reload mode m Nota fault the un
15. balanced load detection system has interrupted the spin because the laundry is unevenly distributed Distribute small and large items of washing in the drum Reduced Ironing selected m Selected speed too low Not a fault the unbalanced load detection system is adjusting the imbalance m Nota fault the unbalanced load detection system is adjusting the imbal ance by repeatedly distributing the laundry m Nota fault the foam detection system active adds an additional rinse cycle Not a fault the programme sequence is optimised for the particular washing process This may lead to changes in the programme duration in the display panel m Nota fault the effect of the care product is not affected m Clean the insert if necessary gt Page 21 Run Cottons 90 C programme without washing Use standard detergent Too much detergent used Mix one tablespoon of fabric softener with 1 2 litre water and pour into com partment II not for outdoor fabrics or those made with down Reduce the detergent dosage for the next wash cycle m Are the appliance feet fixed Secure the appliance feet gt Page 33 m Transport locks removed Remove the transport locks gt Page 30 Clean the detergent solution pump gt Page 21 m Power cut Circuit breakers tripped Switch the circuit breakers back on or replace them m Ifthe fault occurs repeatedly call the after sales service Occasionally phosphate free detergents co
16. button until the required setting is displayed Note The programme duration is included in the selected Finished in time 14 After the start the preselected time e g 8 h is displayed and the time counts down to the start of the washing programme The programme duration is then displayed e g 2 30 hours minutes Changing the preselected time You can change the preselected time after the start of the programme as follows 1 Press the Finished in button repeatedly until the required number of hours is displayed 2 Press the Start Reload button Adding laundry while the preselected time continues running 1 Press Start Reload 2 YES lights up in the display panel The washing machine door can be opened and you can add laundry 3 Close the washing machine door 4 Press the Start Reload button The oreselected time continues to run Additional programme settings U Speed For washing in a shorter time with a washing result comparable to that of the standard programme Note Do not exceed the maximum load Overview of programmes gt Page 12 Eco For saving energy with a washing result comparable to that of the standard programme Note The washing temperature is lower than the selected temperature For special hygiene requirements we recommend selecting a higher temperature or the Speed option Easy lron Special spin sequence with subsequent fluffing Gentle final spin
17. by a small box or a dash Contents Intended use 4 Safety instructions 5 Electrical safety nannaa aana aa 5 Risk of INnjUTY n on annaa aaa 5 Safety for children 0 5 Environmental protection 6 Packaging used appliance 6 Tips on economical use 6 Main points in brief 7 Getting to know the appliance 8 Washing machine 05 8 Control panel 008 9 Display panel oc casa suew de dene wats 9 Ma Laundry asanannnnunnnne 10 Sorting laundry esaa annaua ba oa 10 Prepare the laundry 10 Detergent 00000e eens 11 Correct selection of detergent 11 Saving energy and detergent 11 Overview of programmes 12 Programmes on the programme selector dc aks acl Ge ge 6 8 Gas 12 ler GING aac ae race we Gre are dre cis eee 13 Dyeing bleaching 00 13 SOAKING cee 13 Programme default settings 14 Spin speed 2000 ee 14 Finished in 0000 14 Additional programme SENOS scccecdcacea sede ame 14 U GOCCO 4 44 oedaehen uence Sean 14 BOO etna deen oe ee Sees 14 amp Easy lron 02 eee 15 Rinse OIUS remen arere aw aes 15 en Water plus 000 eee 15 lt 4 Operating the appliance 15 Preparing the washing machine 15 Select programme switch on the appliance noana aaa 15 Change the programme default SCUINGS aoaaa is select a
18. cessary Change the height by turning the appliance feet All four appliance feet must stand firmly on the ground 3 Tighten the lock nut against the housing In doing so hold the foot tight and do not adjust its height The lock nuts on all four appliance feet must be screwed tightly against the housing 33 en Positioning and connecting Electrical connection Warning Risk of death There is a risk of electric shock if you touch live components m Never touch or hold the mains plug with wet hands m Only pull out the mains cable by the olug and never by the cable as this could damage it m Never unplug the mains plug during operation Observe the following information and ensure that Notes m he mains voltage and voltage indicated on the washing machine rating plate are the same The connected load and fuse required are specified on the rating olate he washing machine is only connected to an alternating current via a properly installed earthed socket m Ihe mains plug fits the socket m Ihe cable cross section is adequate m The earthing system is properly installed Ihe mains cable is only replaced by a qualified electrician if this is necessary Replacement mains cables are available from the after sales service No multiple plugs couplings or extension cables are used m lf an earth leakage circuit breaker is used only a type which displays this symbol is used Onl
19. d energy and water consumption Standard programmes for Cottons in accordance with reg Load Approximate pro ulation gramme duration EU no 1015 2010 Cottons programme button lt __ Eco kg an Cottons programme DURON aan ECO SOKO 3 Yah Cottons programme sms 010 0 0 NECO 3 0 kg 3 14h Programme setting for testing and energy labelling in accordance with Directive 2010 30 EU with cold water 15 C The specification of the programme temperature is based on the temperature stated on the care label in the textiles The actual washing temperature may deviate from the stated programme temperature for energy saving reasons Technical data Dimensions 850 x 600 x 590 mm height x width x depth Weight 68 75 kg depending on the model Mains connection Mains voltage 220 240 V 50 Hz Nominal current 10 A Nominal power 2000 2300 W Water pressure 100 1000 kPa 1 10 bar Power consumption when switched off 0 20 W Power consumption when ready for use left on mode 1 90 W 28 Positioning and connecting Included with the appliance Elbow for securing the water drain hose Mains cable Water supply hose on Aqua stop Aqua Secure models Bag m Installation and operating instructions After sales service location directory Warranty Cover caps for openings left after removing the transport locks m Spanner Water drain hose L 6 Water supply hose on standard models dep
20. d water damage you must follow the instructions in this section Notes m In addition to the safety information listed here the local water and electricity supplier may have special requirements m lf in doubt have the appliance connected by a specialist Installation surface Note The washing machine must be Stable so that it does not move around m Ihe surface on which it is installed must be firm and level m soft floors floor coverings are not Suitable Installation on a base ora wooden joist floor Caution Damage to the appliance The washing machine may wander and tip topple from the base when spinning Use holding brackets to secure the feet of the appliance Order no WMZ2200 WX975600 Z 080X0 Note On wooden joist floors install the washing machine m In a corner if possible m On a water resistant wooden board min 30 mm thick which is screwed tightly to the floor 30 Installing the appliance ina kitchenette Z Warning Install the appliance underneath the worktop or fitted in a cabinet before connecting it to the power supply Notes m Recess width of 60 cm required m Only install the washing machine underneath a continuous worktop that is securely connected to adjacent cabinets Z Warning Risk of electric shock Instead of the appliance covering plate you must have a metal cover fitted by an expert Order no WMZ2420 WZ10190 Removing the transport locks
21. dditional programme SettINGS ee es 16 Placing laundry into the drum 16 Measure and add detergent and care products 000 e eee 16 Start the programme 17 Childproof lOCK a2 444 0 222 4a0ed 17 Adding laundry 00005 18 Changing the programme 18 Cancel the programme 18 Programme end during rinse hold 18 Programme end 00008 18 Removing laundry switching off the appliance 24 oe ena sdded ae ee ea be 1 D Sensors c0ecceecaees 19 Automatic load sensing 19 Unbalanced load detection system 19 E Setting the signal 20 Cleaning and maintenance 20 Machine housing control panel 20 Pod eve a ae ee pee eh ee era 21 Descaling 4 cy aan ne Daas ae 21 Detergent drawer and housing 21 Detergent solution pump blocked 21 The drain hose at the siphon is DOCK na rrr cece bas oe 22 Filter in the water supply blocked 22 Faults and what to do about MOM eecea ahe es ee ae ee ee 23 Emergency release 0 23 Information on the display panel 24 Faults and what to do about them 24 en Intended use After sales service 26 a Consumption rates 27 Energy and water consumption programme duration and residual moisture for the main washing programmeS 0002eeeee 21 Efficiency test programmes for cotton TADOS 2 sc bus oo emor a BS ee a 28 Technical data
22. drain hose so that it cannot Slip out Notes m Do not kink the water drain hose or put strain on it lengthways Height difference between the installation surface and the drain Min 60 cm max 100 cm You can lay the water drain hose as follows Drainage into a washbasin Warning Risk of scalding When you are washing at high temperatures there is a risk of scalding if you come into contact with hot detergent solution e g when draining hot detergent solution into a washbasin Do not reach into the hot detergent solution Caution Damage to the appliance fabrics If the end of the drain hose is immersed in the drained water water may be sucked back into the appliance and may damage the appliance fabrics Make sure that The plug does not block drainage from the washbasin The end of the drain hose is not immersed in the drained water The water drains away quickly enough Drainage into a siphon The connection point must be secured using a hose clamp with a diameter of 24 40 mm available from specialist dealers Positioning and connecting en IH J Levelling Level the appliance using a spirit level Incorrect levelling may result in intense noise vibrations and wandering 1 Loosen the lock nuts using a spanner by turning it in a clockwise direction 2 Check the levelling of the washing machine with a spirit level and adjust it if ne
23. ending on the model Positioning and connecting en Notes m Check the machine for transport damage Never use a damaged machine If you have a complaint please contact the retailer from whom you purchased the appliance or our after sales service Moisture in the drum is due to the final inspection In addition a hose clamp 24 40 mm diameter available from specialist dealers is required to connect the water drain hose to a siphon Useful tools m Spirit level for levelling m Spanner with WAF 13 for loosening the transport locks and WAF 17 for aligning the appliance feet Safety instructions Warning Risk of injury m he washing machine is very heavy Be careful when lifting transporting the washing machine lf the washing machine is lifted by protruding components e g the washing machine door the components may break off and Cause injuries Do not lift the washing machine by protruding parts m lf the hose and mains cables are not routed properly there is a risk of tripping and injury Lay hoses and cables in such a way that there is no risk of tripping Caution Damage to the appliance Frozen hoses may crack burst Do not install the washing machine in areas exposed to frost and or outdoors 29 en Positioning and connecting Caution Water damage The connection points for the water Supply hose and water drain hose are under high water pressure To prevent leaks an
24. il the detergent solution begins to flow out When the service flap is half full close the pump cover and drain the service flap Repeat the above steps until all the detergent solution has completely drained out 6 Carefully unscrew the pump cover residual water may leak out Clean the interior pump cover thread and pump housing The impeller in the detergent solution pump must be able to rotate Refit the pump cover and screw it on tightly The handle must be ina vertical position 7 Place the service flap back on lock it into place and close it Note To prevent unused detergent from flowing straight into the drain during the next wash Pour 1 litre of water into compartment Il and start the Drain programme 22 The drain hose at the siphon is blocked 1 Switch off the appliance Pull out the mains plug 2 Loosen the hose clamp Carefully remove the drain hose residual water may leak out 3 Clean the drain hose and siphon connecting piece 4 Reattach the drain hose and secure the connection point using the hose Clamp Filter in the water supply blocked Z Warning Risk of electric shock Do not immerse the Aqua Stop safety valve in water it contains an electric valve For this first reduce the water pressure in the supply hose 1 Turn off the water tap 2 Select any programme except Rinse Spin Drain 3 Press the Start Reload button
25. le washing process is required e g Delicate Silk programme wW Suitable for washing by hand e g amp Wool programme 10 Do not wash the laundry in the machine Prepare the laundry Caution Damage to the appliance fabrics Foreign objects e g Coins paperclips needles nails may damage the laundry or components in the washing machine You should therefore note the following tipos when preparing your laundry m Empty any pockets m Look out for metal items paperclips etc and remove them m Wash delicates in a laundry bag tights underwired bras etc m Close any zips button up any cover buttons m Brush sand out of pockets and collars m Remove curtain fittings or place Curtains in a laundry bag Detergent Correct selection of detergent The care label is crucial for selecting the correct detergent temperature and treatment of the laundry gt See also www sartex ch Visit www cleanright eu to find further information on detergents care products and cleaning agents for domestic use Standard detergent with optical brighteners Suitable for heat resistant white laundry made from linen or cotton Programme Cottons 20 C max 90 C Detergent for colours without bleach or optical brighteners Suitable for coloured laundry made from linen or cotton Programme Cottons 20 C max 60 C Detergent for colours delicates without optical brighteners Sui
26. n Safety for children Z Warning Risk of death If children play with the washing machine they may get into life threatening situations or injure themselves Do not leave children unattended near the washing machine Do not let children play with the washing machine Z Warning Risk of death Children may lock themselves in appliances putting their lives at risk When appliances have reached the end of their service life Pull out the mains plug en Environmental protection a Cut through the mains cable and remove it along with the plug Destroy the lock on the washing machine door Z Warning Risk of suffocation Children may become wrapped in packaging film or packing parts if allowed to play with them or they may pull them over their heads and suffocate Keep packaging film and packaging parts out of the reach of children Z Warning Risk of poisoning Detergents and care products may be poisonous if consumed Keep detergents and care oroducts out of the reach of children Z Warning Eye skin irritation Detergents and care products may cause Irritation if they come into contact with the eyes or skin Keep detergents and care oroducts out of the reach of children Z Warning Risk of injury When you wash at high temperatures the glass in the washing machine door becomes hot Do not let children touch the hot washing machine door Environmental
27. necessary Ea Programme end Open the washing Turnthe programme Turn off the water machine door and selector to tap for models remove the laundry without Aqua Stop en Getting to Know the appliance Getting to know the appliance Washing machine Detergent drawer gt Page 16 Washing machine door with door handle Controls display elements Open the washing machine door Close the washing machine door Service flap Getting to Know the appliance en Control panel Speed _ i Start Easy Care 4 ae Cottons ee o Spin Reload o 1200 DI Eco 1000 fie te Remect lt i A o 800 40 Prewash Reduced 600 ae lroning i O Rinse Hold R ady in Z Drain A Rinse Spin O car ere 40 Mixed Load Load So peor 6 1 0 Speed cok Z Reduced Display panel for settings and information Ironing w Rinse Plus amp Water Plus Aqua Plus additional programme settings depending on the model Overview of all additional programme settings l Start Reload for starting interrupting adding laundry and cancelling a programme L2 3 Spin speed Ready in Finished in L 6_ Programme selector for selecting a for changing the programme default settings programme and for switching the machine on w Rinse stop and off Overview of all programme default settings Display panel Settings for the selected programme 1 30 Programme duration Depends on the progr
28. nfirmed They are not saved when the appliance is switched off Programme default settings Page 14 Overview of programmes from Page 12 15 en Operating the appliance Select additional programme settings By selecting additional settings you can better adapt the washing process to your items of laundry The settings can be selected or deselected depending on the programme progress The indicator lamp for the button lights up if a setting is active The settings are not saved when the appliance is switched off Additional settings gt Page 14 Overview of programmes from Page 12 Placing laundry into the drum Z Warning Risk of death Items of laundry pretreated with cleaning agents that contain solvents e g stain remover cleaning solvent may cause an explosion after being loaded into the washing machine Hand rinse these items of laundry thoroughly beforehand Notes Mix items of laundry of varying sizes Laundry items of different sizes distribute themselves better during the spin cycle Individual items of laundry may lead to imbalances Observe the maximum specified load Overfilling has a negative impact on the washing result and promotes creasing 1 Place presorted items of laundry unfolded in the washing drum 2 Make sure that no items of laundry are trapped between the washing machine door and the rubber seal and close the door 16 The Start Reload b
29. ntain water insoluble residues m Select Rinse Spin or brush the laundry after washing m Water level too high Not possible to add laundry Close the washing machine door immediately if necessary m Select Start Reload to continue the programme 25 en After sales service Faults Cause remedial action YES appears on the dis The washing machine door is unlocked It is possible to add laundry play in reload mode If you cannot correct a fault yourself after switching off on or a repair is required m Turn the programme selector to Off Appliance is switched off m Unplug the mains plug from the socket m urn off the water tap and call the after sales service After sales service If you cannot rectify a fault yourself Faults and what to do about them Page 24 please contact our after sales service gt Cover page We will always find an appropriate solution in order to avoid unnecessary visits by engineers Please give the after sales service the product number E Nr and the production number FD of the appliance E Nr FD Product number Production number You can find this information depending on the model On the inside of the washing machine door in the opened service flap and on the rear of the appliance Trust the expertise of the manufacturer Contact us for assistance By doing so you will ensure that the repairs are carried out by trained service personnel using
30. o continue or change the programme Dye should only be used in normal household quantities Salt may damage Notes Stainless steel Always follow the dye m Load laundry of the same colour manufacturer s Instructions m No additional detergent is required Do not use the washing machine to the soaking solution is used for bleach clothes washing 13 en Programme default settings Programme default settings The spin speed and programme duration Ready in time for all programmes are preset at the factory These are displayed in the display panel after selecting the programme You can change the default settings as follows Spin speed Before and while the selected programme is running the spin speed or w without final spin laundry soaks in the last rinsing water display panel can be set The effects depend on the programme progress The maximum selectable spin speed depends on the model and the set programme Page 12 Finished in When you select the programme the relevant programme duration is displayed The programme duration is automatically adjusted when the programme is running Changes to the programme default settings or programme settings also change the programme duration Before starting the programme the programme end Finished in time can be preselected in increments of one hour h hours up to a maximum of 24 hours To do this repeatedly press the corresponding
31. protection Packaging used appliance x Dispose of packaging in an environmentally responsible manner This appliance is labelled in accordance with European Directive 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Tips on economical use m Always fill the appliance with the maximum amount of laundry for each programme Overview of programmes Page 12 m Wash normally soiled laundry without a prewash m lf the laundry is subsequently dried in a tumble dryer select the spin speed according to the tumble dryer manufacturer s instructions m The selectable temperatures apply to the care labels on the textiles The temperatures in the machine may deviate from this so that you get the optimum mix of energy saving and washing results Main points in brief en Main points in brief D D t a EL Connect the mains Turn on the water Sort the laundry Open the washing plug tap for models machine door without Aqua Stop Select a Load the laundry Do not trap any Close the washing programme e g items of laundry machine door Cottons D p R D gt lt lt O R DM a w A O 4 Add detergent Change the select additional Start the programme default settings if programme settings if
32. s plug 2 Drain off the detergent solution Page 21 3 Use a tool to pull the emergency release downwards and release it The washing machine door can then be opened 23 en Faults and what to do about them Information on the display panel Display NES NO NO flashes EIO RIZ Flg a F23 C gt amp flashes Cause remedial action The washing machine door is unlocked It is possible to add laundry m lemperature too high Wait until the temperature drops m Water level too high Not possible to add laundry Close the washing machine door immediately if necessary Select Start Reload to continue the pro gramme m Wait until YES lights up Close the door properly laundry may become trapped Turn the water tap on fully supply hose kinked or trapped water pressure too low Clean the screen Detergent solution pump blocked Clean detergent solution pump The drain hose waste pipe is blocked Clean the drain hose on the siphon Motor fault Call the after sales service Water in the base tub appliance leaking Call the after sales service Childproof lock activated deactivate it Too much foam detected a rinse cycle has been switched on Faults and what to do about them Faults Cause remedial action Water is leaking out Attach replace the drainage hose correctly Tighten the screw connection of the supply hose No water supply Start Reload not selected Detergent not dispensed T
33. supply hose Maintenance filter in the water supply gt Page 22 Drain the remaining detergent solution Maintenance detergent solution pump blocked gt Page 21 Disconnect the washing machine from the mains Remove the hoses Installing the transport locks 1 Remove the covers and keep them in a safe place Use a screwdriver if necessary Insert all 4 sleeves Clip the mains cable securely in the holders Insert and tighten the Screws Before commissioning Notes The transport locks must be removed To prevent unused detergent from flowing straight into the drain during the next wash Pour approx 1 litre of water into compartment Il and start the Drain programme Positioning and connecting en 35 Aqua Stop warranty Only for appliances with Aqua Stop In addition to warranty claims against the vendor based on the purchase agreement and to our appliance warranty we will provide compensation under the following conditions 1 If water damage is caused due to a fault in our Agua Stop system we will compensate domestic customers for the damage caused 2 The liability guarantee is valid for the service life of the appliance 3 It is a prerequisite of all warranty claims that the appliance with Aqua Stop must have been installed and connected correctly in accordance with our instructions this also includes a correctly fitted Aqua Stop extension genuine accessories Our warranty does
34. table for coloured laundry made from easy care fibres synthetic fibres Programme Easy Care 20 C max 60 C Delicates Suitable for delicate fine fabrics silk or viscose Programme Delicates Silk 20 C max 40 C Detergent for woollens Suitable for woollen fabrics Programme Woollens 20 C max 40 C Detergent en Saving energy and detergent For light and normal soiling you can save energy lower washing temperature and detergent Saving Soiling note Reduced temper Light ature and deter No visible dirt or stains Cloth gent quantityas ing has taken on some body per the recom Odour e g mended dosage Light summer sports clothing worn for a few hours m shirts shirts blouses worn for up to one day m Guest bed linen and hand towels used for one day Normal Visible dirt or a few light stains g m shirts shirts blouses Sweat soaked worn a few times m Towels bedding used for up to one week Temperature as Heavy per the care label Dirt and or stains clearly visi and detergent ble e g tea towels baby quantity as per items work clothing the recom mended dosage for heavy soiling Note When measuring the amount of all detergents additives care products and cleaning agents please always check the manufacturer s instructions and information gt Page 16 11 en Overview of programmes Overview of programmes Programmes on the
35. tallation Instructions and all other information supplied with the washing machine and use the machine accordingly Retain the documents for subsequent use Safety instructions Electrical safety Z Warning Risk of death There is a risk of electric shock if you touch live components Never touch or hold the mains plug with wet hands a Only pull out the mains cable by the plug and never by the cable as this could damage it Risk of injury A Warning Risk of injury a f the washing machine is lifted by protruding components e g the washing machine door the components may break off and cause injuries Do not lift the washing machine by protruding parts a If you climb onto the washing machine the worktop may break and cause injuries Do not climb onto the washing machine a f you lean sit on the opened washing machine door the washing machine may tip over and cause injuries Do not lean on the washing machine door when it is open Safety instructions en m Reaching into the drum while it is still rotating may cause hand injuries Do not reach into the drum while it is rotating Wait until the drum has stopped rotating Z Warning Risk of scalding When you are washing at high temperatures there is a risk of scalding if you come into contact with hot detergent solution e g when draining hot detergent solution into a washbasin Do not reach into the hot detergent solutio
36. te the childproof lock after starting the programme To activate deactivate the childproof lock press and hold Start Reload for approx five seconds The symbol appears on the display panel m lights up The childproof lock is active 17 en Operating the appliance m flashes The childproof lock is active and the programme selector has been adjusted To prevent the programme from stopping turn the programme selector back to the original programme The symbol lights up again Note The childproof lock can remain activated until you wish to start the next programme even after switching off the machine You must then deactivate the childproot lock before starting the programme and activate it again as necessary once the programme has started Adding laundry After starting the programme you can add or remove laundry as required To do this press the Start Reload button The Start Reload indicator lamp flashes and the machine checks whether it is possible to add laundry Note Do not leave the washing machine door open for too long when adding laundry as water from the laundry may leak out lf on the display panel YES lights up it is possible to add laundry NO flashes wait until YES lights up A flashing NO symbol it is not possible to add laundry For safety reasons the washing machine door remains locked when the water level or temperature is high or while the drum is rota
37. ting and it is not possible to add laundry To continue the programme press the Start Reload button The programme continues automatically 18 Changing the programme If you have started the wrong programme by mistake you can change the programme as follows 1 Select the other programme 2 Press the Start Reload button The new programme starts from the beginning Cancel the programme For programmes at high temperatures 1 To cool the laundry select Rinse Spin 2 Press the Start Reload button For programmes at low temperatures 1 Press Start Reload 2 Select Rinse Spin deactivate the Rinse plus Water plus button or select Drain 3 Press the Start Reload button Programme end during rinse hold appears on the display panel the status display lights up and the Start Reload button indicator lamp flashes To end the programme set the programme selector to Drain or select a spin speed Then press the Start Reload button Programme end 0 appears on the display panel and the Start Reload button indicator lamp flashes If the amp symbol also appears on the display panel the washing machine has detected too much foam during the wash programme and automatically switched on a rinse cycle to remove the foam Note Add less detergent for the next washing cycle with the same load Removing laundry switching off the appliance 1 Open the washing machine door and remove
38. undry information Settings Wool Max 2 kg Hand or machine washable fabrics that are made of wool or contain cold 30 C wool w 800 rpm Particularly gentle wash programme to prevent shrinkage of laundry with longer programme breaks fabrics rest in the detergent solu tion Notes m Wool is of animal origin e g Angora alpaca llama sheep m Use a detergent which is suitable for machine washing wool Rinse Spin Max 7 kg Laundry washed by hand Rinse plus Water plus button activated Note If you require spin only deactivate the button ww 1200 rom za YW Drain Max 7 kg Drain the rinsing water after a programme using the setting w without final spin for gentle treatment of delicate laundry SuperQuick 15 Max 2 kg Extra short programme of approx 15 minutes suitable for small NN items of lightly soiled laundry 1200 rpm Starching Soaking Note Laundry must not be treated with 1 Pour soaking agent detergent into fabric softener compartment Il in accordance with the manufacturer s instructions Turn the programme selector to Cottons 30 C programme Press the Start Reload button After approx 10 minutes press Starching is possible in all wash programmes if liquid starch is used Measure starch into compartment amp in accordance with the manufacturer s ee 6 instructions clean first if necessary Start Reload After the required soaking time Dyeing bleaching press Start Reload again t
39. utton indicator lamp flashes and the programme settings continue to be displayed on the display panel one after another It is possible to change the settings Measure and add detergent and care products Caution Damage to the appliance Cleaning agents and agents for pretreating laundry e g stain removers prewash sprays etc may cause damage if they come into contact with the surfaces of the washing machine Do not allow these agents to come into contact with the surfaces of the washing machine If necessary immediately wipe away spray residue and other residues droplets with a damp cloth Measuring Measure the detergent and care products according to m Water hardness ask your water Supply company m he manufacturer s instructions on the packaging Ihe amount of laundry m Soiling Page 11 Filling Z Warning Eye skin irritation Detergent and care products may spray out If the detergent drawer is opened while the machine is in operation Open the drawer carefully Rinse eyes or skin thoroughly if they come into contact with detergent care oroducts lf swallowed accidentally seek medical advice Note Dilute viscous fabric softener and fabric conditioner with water this orevents blockages Pour the detergent and care products into the appropriate compartments Measuring aid A For liquid detergent Compartment Il Detergent for the main wash water softener bleach stain remover
40. washing machine contains detergent or fabric softener residues 1 Pull out the detergent drawer Press down the insert and fully remove the drawer from the housing 2 To remove the insert push the insert up from below with your finger 3 Clean the detergent dispenser tray and insert with water and a brush and dry it Also remove any detergent or fabric softener residues in the housing 4 Fit the insert and lock it in place oush the cylinder onto the guide pin 5 Push in the detergent drawer Cleaning and maintenance en Note Leave the detergent drawer open so that any residual water can evaporate Detergent solution pump blocked Z Warning Risk of scalding When you wash at high temperatures the detergent solution gets very hot If you come into contact with the hot detergent solution you may be scalded Allow the detergent solution to cool down 1 Turn off the water tap so that no more water can flow in and has to be drained via the detergent solution pump 2 Switch off the appliance Pull out the mains plug 3 Open and remove the service flap 4 For models with a drain hose Take the drain hose out of the retainer Remove the sealing cap allow the detergent solution to flow out into a Suitable container Replace the sealing cap and place the drain hose in the retainer 21 en Cleaning and maintenance 5 For models without a drain hose Carefully unscrew the pump cover unt
41. y this symbol guarantees compliance with the currently applicable regulations m he mains plug can be accessed at all times m Ihe mains cable is not bent squashed modified cut through or in contact with heat sources 34 Before washing for the first time The washing machine was thoroughly tested before leaving the factory In order to remove any water which may be left over from the test run the first washing cycle without any laundry Notes m The washing machine must be correctly installed and connected from Page 29 m Never use a damaged machine Inform your after sales service Check the machine Remove the protective film from the control panel Connect the mains plug Turn on the water tap Close the washing machine door do not load any laundry Select the Cottons 90 C programme Open the detergent drawer Pour approx 1 litre of water into compartment Il Pour standard detergent into compartment Il Note To prevent foaming only use half of the amount of detergent recommended by the detergent manufacturer Do not use detergent for wool or delicates 10 Close the detergent drawer 11 Press the Start Reload button 12 Switch off the appliance at the end of the programme Your washing machine is now ready to use o On P PeP PA Transportation E g when moving house Preparatory work 1 Turn off the water tap 2 4 5 Reduce the water pressure in the

Download Pdf Manuals

image

Related Search

Related Contents

Harbor Freight Tools 212cc Quick Start Guide  Nouvelle procédure de connexion à Intervat    índice  Technical Data Sheet  Moxa A-ADP-RJ458P-DB9F-ABC01  LG G3 D855 16GB 4G Black  Filles-garçons, mode d`emploi  ITS-200  Design Juicer Advanced 800 Class  

Copyright © All rights reserved.
DMCA: DMCA_mwitty#outlook.com.