Bosch SMI50C02GB dishwasher
Contents
1. to the Remaining running time display When the programme is selected the remaining running time of the programme is indicated on the digital display The running time is determined during the programme by the water temperature the number of utensils as well as the degree of soiling and may vary depending on the selected programme Timer programming depending on model You can delay the start of the programme in 1 hour steps up to 24 hours Close the door Switch on ON OFF switch L 1 Press button L6 until the digital display L5_ jumps to 4 I Press button L6 until the displayed time corresponds with your requirements Press START button 4 timer programming is activated To delete the preselected starting time press the button L6 until A is indicated on the digital display You can change your programme selection at any time until the programme starts End of programme The programme has ended when the value Zi is indicated on the numerical display 5 Switching off automatically after the end of the programme depending on model To save energy the dishwasher is switched off 1 minute after the programme ends factory setting Automatic disconnection can be adjusted from PIO to Pie F 00 Appliance does not switch off automatically PD Off after 1 m2. 23 Safety instructions 23 Dever sedata e A TNE 24 Technical specifications 24 Installation LL a a 24 Waste water connection 24 Fresh water connection 24 Warm water connection 25 Electrical connection 25 Removing the appliance 25 Transportation 26 Protection against frost Emptying the appliance 26 Waste disposal 26 Packaging ma oe asas aces ede ead 26 Old appliances 26 en Safety instructions Before you switch ON the appliance Please read the operating and installation instructions carefully They contain important information on how to install use and maintain the appliance Retain all documents for subsequent use or for the next owner DE NE Check the packaging and dishwasher immediately for damage caused in transit Do not switch on a damaged appliance but contact your supplier Please dispose of the packaging material in an environmentally friendly manner Do not let children play with packaging and its parts There is a risk of suffocation from collapsible boxes and film Installation Read the Installation chapter to learn how to install and connect the appliance correctly In daily use This appliance is intended for use in the home and the home environment Use the dishwasher only in the household and only for its designed purpo
3. hwasher IS D Operating instructions en TI TI UL png i aa ea aa eee a ALL I oj ooN m SF PLO o IN O G LG my NN ON ON N QU ENE ENP LANE LAY co en Table of contents Safety instructions 4 Before you switch ON the appliance 4 Bie no ai ae Lia dai eee 4 Installation wi sagra a RA au 4 In dail S cieli pei di 4 Children in the household 4 BDOOPFIOGK miti af id kia a ia 5 DAMAGE pss Ki a ka S 5 Disposal ues eee detains erai aa 5 Getting to know your appliance 5 Control panel 5 Appliance interior 5 Water softening system 6 SEtlingis pi iii aha be A 6 Water hardness table 6 Special saltS 7 Using special salt 7 Detergents with salt component 7 Switching off water softening system 7 Rinse aid 0 0 0 cece eee ees 8 Setting amount of rinse aid 8 Switching off rinse aid refill indicator 8 Utensils sua ia nia e be a 9 Not suitable as 9 Glass and utensil damage 9 Loading the dishwasher 9 Unloading the dishwasher 9 Cups and glasses 9 PANGS 2 sek one antes ls aa ie 10 Cutlery basket 10 ETAQG CLE e ace ala pi 10 Folding spikes 10 Small accessories holder 11 Knife shelf icona 11 Adjusting the h
4. No too little rinse aid No too little special salt Water softening system set to the wrong value Salt dispenser lock not fastened Contact the detergent manufacturer in particular if the utensils are very wet at the end of the programme limescale forms Dull discoloured glasses film cannot be washed off Unsuitable detergent Glasses not dishwasher proof Streaks on glasses and cutlery glasses have metallic appearance Too much rinse aid Plastic parts discoloured Too little unsuitable detergent Too weak programme selected Rust spots on the cutlery Cutlery not rust resistant Salt content in the rinsing water too high as salt dispenser lock not fastened firmly or salt was spilled while being refilled Utensils not dry Appliance door opened too early and utensils taken out too early Programme selected without drying Too little unsuitable rinse aid Activate intensive drying The combined detergent used has a poor drying performance Use rinse aid see Rinse aid chapter for setting Customer service If the advice given does not resolve your problem please contact your customer service Contact details can be found on the back cover of this instruction manual or in the enclosed customer service list When calling please quote the appliance number 1 and the production date FD 2 which can be found on the rating plate L32 on the appliance d
5. selection You can select a suitable programme according to the type of utensils and degree of soiling Information for test institutes Test institutes can reguest the conditions for running comparison tests by sending an e mail to dishwasher test appliances com Quote the appliance number E Nr and the production date FD which you can find on the rating 32 plate on the appliance door 15 en Additional options depending on model Additional options can be set with the buttons L7 L G Express Wash Speed Perfect VarioSpeed This function can reduce the running time by approx 20 to 50 depending on the selected rinse programme The change in the running time is indicated on the digital display L5 To obtain optimum cleaning results at a reduced running time water and energy consumption are increased Half load If you have only a few items to wash e g glasses cups plates you can switch to half load This will save water energy and time It is recommended to put a little less detergent in the detergent dispenser than for a full load Hygiene The temperature is increased during the cleaning process This increases the hygiene status This additional option is ideal for cleaning e g chopping boards and baby bottles Intensive zone Perfect for a mixed load You can wash very soiled pots and pans in the lower basket together with normally s
6. the lock 31 to open the detergent dispenser Pour detergent into the dry detergent dispenser 30 only insert tablet flat not on its edge Dosage see manufacturer s instructions on the packaging The graduated detergent dispenser 30 helps you add the correct amount of powder or liquid detergent Usually 20 ml 25 ml are adequate for normal soiling If using tablets one tablet is adequate Close the cover on the detergent dispenser by sliding it up until the lock engages without difficulty The detergent dispenser opens automatically at the optimum time depending on the programme The powder or liquid detergent is distributed in the appliance and is dissolved the tablet falls into the tablet collecting tray where it dissolves in doses en Tip If the utensils are only lightly soiled slightly less than the indicated amount of detergent is usually adequate Suitable detergents and care products can be purchased online via our website or via customer service see back page Combination detergent Apart from conventional detergents Solo a number of products are offered with additional functions These products contain not only the detergent but also rinse aid and salt replacement substances 3in1 and depending on the combination 4in1 5in1 etc additional components such as glass protection or stainless steel cleaner Combination detergents func
7. a correctly installed socket with protective earth conductor See rating plate for required fusing 32 The socket must be near the appliance and freely accessible following installation If the plug is not freely accessible an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions The connection may be modified by technicians only A power cord extension may be purchased from customer service only Use only a residual current operated circuit breaker which features the symbol EX Only this extension guarantees compliance with the currently valid regulations The appliance features a water damage protection system Please note the system will not function unless the power supply is connected Removing the appliance Also observe the sequence of worksteps here Disconnect the appliance from the power supply Turn off the water supply Disconnect the waste water and fresh water connections Loosen fastening screws for the furniture parts If fitted remove the base panel Pull out the appliance carefully pulling the hose behind 25 en Transportation Empty the dishwasher and secure loose parts Drain the appliance according to the following steps Turn on the tap Close the door Switch on ON OFF switch L 1 Select programme with the highest temperature The ex
8. cannot be closed Door lock has been activated To reset close the door with greater force Cover on the detergent dispenser cannot be closed Detergent dispenser overfilled or mechanism blocked by sticky detergent residue Detergent residue in the detergent dispenser Dispenser was damp when filled Check water supply display 10 lights up Tap turned off Water supply interrupted Supply hose kinked Error code 2 Filters Refill indicator for salt 9 aid Refill indicator for special salt 9 en Filter in the water supply blocked Switch off the appliance and pull out the mains plug Turn off the tap Clean filter in the supply hose Reconnect power supply Turn on the tap Switch on the appliance Water is left in the appliance at the end of the programme 2 4 Waste water hose is blocked or kinked Filters blocked 25 Waste water pump blocked cover on the waste water pump is not locked in position see Waste water pump Filters blocked The programme has not yet ended Wait until programme ends digital display indicates 2 07 or implement the Reset function 26 are soiled or blocked and or rinse 8 is not lit Refill indicator s switched off Adequate salt rinse aid available No is lit salt Refill with special salt Sensor does not
9. del Light weight plastic accessories e g cups lids etc can be held securely in the small accessories holder en Adjusting the height of the basket depending on model If required the height of the upper utensils basket 20 can be adjusted to provide more space for tall utensils either in the upper or lower basket Appliance height 81 5 cm Knife shelf depending on model Long knives and other utensils can be arranged horizontally Top basket Bottom basket Setting 1 max g 22 cm 30 cm Setting 2 max g 24 5 cm 27 5 cm Setting 3 max g 27 cm 25 cm Appliance height 86 5 cm Top basket Bottom basket Setting 1 max g 24 cm 33 cm Setting 2 max g 26 5 cm 30 5 cm Setting 3 max g 29 cm 28 cm Select one of the two following procedures according to the design of the top basket for your appliance model 11 en Top basket with side levers Pull out the top basket 20 out To lower the basket press in the left and then the right lever on the outside of the basket In doing so hold the sides of the basket along the upper edge to prevent it from suddenly dropping Toraise the basket hold the basket on the sides of the upper edge and lift it up Before re inserting the basket again ensure that it is at the same height on both sides Otherwise the appliance doo
10. detect salt tablets Use different special salt 21 en during the wash cycle Unusual foam formation Handwash liquid in the rinse aid dispenser Spilled rinse aid causes excessive frothing therefore please remove with a cloth Appliance stops during the wash cycle Power supply interrupted Water supply interrupted Filling valves making striking noises Caused by the installation of the water line and has no effect on the function of the machine Remedial action is not possible Knocking rattling noise during rinsing Spray arm is striking utensils Utensils not arranged correctly on the utensils Food residue on the utensils Utensils placed too closely together utensils basket overfilled Too little detergent Rinse programme too weak Spray arm rotation obstructed Spray arm nozzles blocked Filters blocked Filters incorrectly inserted Waste water pump blocked Top basket on right and left not set to same height Tea or lipstick residue is not completely removed The detergent has an inadequate bleaching effect Too low rinsing temperature Too little unsuitable detergent 22 White stains on the utensils glasses remain milky If phosphate free detergents are used with hard tap water white deposits may be deposited more easily on utensils and the container walls Too little unsuitable detergent Too weak programme selected
11. efill indicator Salt refill indicator Display Check water supply IO JOO N o JO DI JOO P par O depending on model Number depending on model Appliance interior 20 Top basket 21 Knife shelf 22 Tablet collecting tray 23 Top spray arm 24 Bottom spray arm 25 Dispenser for special salt 26 Filters 27 Cutlery basket 28 Bottom basket 29 Dispenser for rinse aid 30 Detergent dispenser 31 Lock for detergent dispenser 32 Rating plate depending on model en Water softening system To ensure good washing results the dishwasher reguires soft water i e containing low amounts of lime otherwise white limescale will be deposited on the utensils and inner container Tap water above 9 Clarke must be softened The water is softened with salt regeneration salt in the water softening system of the dishwasher The setting and therefore the required amount of salt depends on the degree of hardness of your tap water see table Setting The amount of salt dispensed can be set from 4 00 to HiG T MM Salt is not required at the set value 4 0 Find out about the hardness value of your tap water Your water utility company will help you with this Set value can be found in the water hardness table Close the door S
12. egratable appliances only under continuous worktops which have been screwed to adjacent cupboards to ensure stability Do not install the appliance near heat sources radiators heat storage tanks cookers or other appliances which generate heat and do not install under a hob 23 en After installing the appliance ensure that the plug is easily accessible see Electrical connection Some models The plastic housing on the water connection contains an electric valve the connecting cables are in the supply hose Do not cut through this hose do not immerse the plastic housing in water A Warning If the appliance is not in a cavity and a side panel is accessible the door hinge area must be covered at the side for reasons of safety risk of injury The covers are available as optional accessories from customer service or specialist outlets Delivery Your dishwasher has been checked thoroughly in the factory to ensure that it is in working order This may cause small water stains These will disappear after the first wash cycle Technical specifications Weight max 60 kg Voltage 220 240 V 50 Hz or 60 Hz Connected load 2 0 2 4 KW Fuse 10 16 A UK 13A Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inlet rate minimum 10 litres minute Water temperature cold water hot water max t
13. eight of the basket 11 Detergent 12 Adding detergent 13 Combination detergent 13 Overview of programmes 15 Programme selection 15 Information for test institutes 15 Additional options 16 Express Wash Speed Perfect VarioSpeed 16 Half loadiri scritte ina 16 HYgISN Li k dai an a 16 Intensive ZONE 16 Extra dying ik ee vec ba dn tea eis 16 Washing the dishes 16 Programme data 16 Agua Sensor LL 0 eee eee 16 Switching on the appliance 16 Remaining running time display 16 Timer programming 17 End of programme 05 17 Switching off automatically after the end of the programme 17 Switching off the appliance 17 Interrupting the programme 17 Terminating the programme 18 Changing the programme 18 Intensive drying LL as 18 Maintenance and care 18 Overall condition of the machine 18 Special salt and rinse aid 18 Filters ae Palaia 19 Spray AarMS i reader 19 Troubleshooting 20 Waste water pump 20 when the appliance is switched on 21 on the appliance 21 during the wash cycle 22 on the utensils 22 Customer service 23 Installation
14. emperature 60 C 24 Installation The required installation dimensions can be found in the installation instructions Level the appliance with the aid of the height adjustable feet Ensure that the appliance is situated securely on the floor A built under or integrated appliance which is installed subsequently as a free standing appliance must be secured to prevent it from overturning e g by screwing it to the wall or by installing it under a continuous worktop which is screwed to adjacent cupboards The appliance can easily be installed in a fitted kitchen between wooden and plastic walls Waste water connection The reguired work sequence can be found in the installation instructions If required fit a siphon with an drainage connection Connect the waste water hose to the drainage connection of the siphon with the enclosed parts Ensure that the drainage hose is not kinked crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out Fresh water connection Connect the fresh water connection to the tap according to the installation instructions with the enclosed parts Ensure that the fresh water connection is not kinked crushed or twisted When replacing the appliance always use a new water supply hose Water pressure at least 0 05 MPa 0 5 bar maximum 1 MPa 10 bar At a higher water pressure connect pressure reducing valve ahead Inl
15. ergent residue Ensure that children do not place fingers in the tablet collecting tray 22 Small fingers could become caught in the slots lf the appliance is installed at eye level ensure when opening and closing the door that children are not caught or crushed between the appliance door and the cupboard door situated below Childproof lock door lock The description of the childproof lock is at the back in the envelope depending on model Damage The appliance may be repaired and opened up by a technician only To do this disconnect the appliance from the power supply Pull out the mains plug or switch off the fuse Turn off the tap Disposal Make redundant appliances unusable to prevent subsequent accidents Dispose of the appliance in an environmentally friendly manner A Warning Children could become locked in the appliance risk of suffocation or find themselves in other dangerous situations Therefore Pull out the mains plug sever and dispose of the power cord Destroy the door lock so that the door can no longer be closed en Getting to know your appliance Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front Individual positions are referred to in the text Control panel ON OFF switch Door opener Programme selector START button Digital display Timer programming Additional options Rinse aid r
16. et rate minimum 10 litres minute Water temperature cold water preferred hot water max temperature 60 C Warm water connection depending on model The dishwasher can be connected to cold or hot water up to max 60 C Connection to hot water is recommended if the hot water can be supplied by energetically favourable means and from a suitable installation e g solar heating system with circulation line This will save energy and time The hot water setting 4 0 allows you to adjust your appliance optimally to operation with hot water It is recommended to have a water temperature temperature of the incoming water of at least 40 C and no more than 60 C It is not recommended to connect the appliance to hot water if the water is supplied from an electric boiler Setting hot water Close the door Switch on ON OFF switch 1 Press and hold down the START button L 4 Rotate programme selector L 3 until A fis indicated on the digital display L5 Release button The factory set value 4 27 is lit on the digital display LS To change the setting By rotating the programme selector you can switch the hot water tara off ADD or on And i Press START button 4 The set value is saved en Electrical connection Connect the appliance to an alternating current only ranging from 220 V to 240 V and 50 Hz or 60 Hz via
17. etergent dispenser with detergent Start the appliance without utensils in the programme with the highest rinsing temperature Clean the appliance with detergents appliance cleaners which are particularly suitable for use with dishwashers Regularly clean door seal with a damp cloth Never use a steam cleaner to clean your dishwasher The manufacturer is not liable for any consequential damage Regularly wipe the front of the appliance and fascia with a damp cloth water and a little washing up liquid are adequate Do not use sponges with a rough surface or abrasive detergents as these could scratch the surfaces Stainless steel appliances To prevent corrosion avoid using sponge cloths or wash them out thoroughly several times before using for the first time A Warning Never use other chlorinated household detergents Health hazard Special salt and rinse aid Check the refill indicators 9 and 8 If required refill salt and or rinse aid Filters The filters L26 keep large foreign objects in the rinsing water away from the pump These foreign objects may occasionally block the filters The filter system consists of a coarse filter a flat fine filter and a microfilter After each washing cycle check the filters for residue Unscrew filter cylinder as illustrated and take out filter system Remove an
18. hnicians only If a component has to be replaced ensure that only original spare parts are used Improper repairs or use of non original spare parts may cause considerable damage and put the user at considerable risk 20 Waste water pump Large food remnants or foreign objects which were not captured by the filters may block the waste water pump The rinsing water will then be above the filter In this case First always disconnect the appliance from the power supply Take out top basket 20 and bottom basket 28 Remove the filters L26 Scoop out water use a sponge if required Prise out the white pump cover as illustrated using a spoon Grip the cover on the crosspiece and lift diagonally inwards Remove cover completely Check impeller wheel and remove any foreign objects Place cover in the original position and press down until it engages click Install filters Re insert baskets when the appliance is switched on The appliance does not start The mains fuse has tripped The appliance plug has not been inserted The appliance door has not been shut properly On the appliance Lower spray arm rotates sluggishly Spray arm blocked The door is difficult to open Child proof lock is activated The deactivation instructions are at the back in the envelope depending on model Door
19. in P 02 Off after 120 min Close the door Switch on ON OFF switch L 1 Press and hold down the START button L 4 Rotate programme selector L 3 until 7 27 s indicated on the digital display 5 Release button The factory set value 7 2 is lit on the digital display L en To change the setting Rotate programme selector L 3 until the required value is indicated on the digital display L5 Press START button 4 The set value is saved Switching off the appliance Short time after the end of the programme Switch off ON OFF switch L 1 Turn off the tap not applicable if Aqua Stop fitted Remove the utensils when they have cooled down A Warning At the end of the programme please open the door fully and not partially when emptying the dishwasher Any escaping water vapour could damage sensitive worktops Interrupting the programme Switch off ON OFF switch L 1 The LEDs go out The programme is saved If the door was opened on an appliance which has a warm water connection or is heated first leave the door ajar for several minutes and then close Otherwise expansion pressure may cause the appliance door to spring open or water to run out of the appliance To continue the programme switch on the ON OFF switch again 17 en Terminating the program
20. me Resen Press START button 4 for approx 3 sec The numerical display L5 indicates G I The programme sequence lasts approx 1 min On the digital display L5 is indicated 2 37 Switch off ON OFF switch 1 Changing the programme When the START button L4 has been pressed the programme cannot be changed The only way a programme can be changed is by Cancel programme Reset Intensive drying The final rinse uses a higher temperature which improves the drying result The running time may increase slightly Caution if utensils are delicate Close the door Switch on ON OFF switch L 1 Press and hold down the START button 4 Rotate programme selector L 3 until d is indicated on the digital display L5 Release button The factory set value d 02 is lit on the digital display L5 intensive drying off Change the setting as follows By rotating the programme selector you can switch intensive drying ot i or off d 00 Press START button 4 The set value is saved 18 Maintenance and care A regular inspection and maintenance of your machine will help to prevent faults This saves time and prevents problems Overall condition of the machine Check spray arm for grease and limescale deposits If you find such deposits Fill d
21. nto an absolutely dry detergent dispenser only otherwise the detergent may stick If you switch from combined detergents to solo detergents ensure that the water softening system and amount of rinse aid have been set to the correct value 14 Overview of programmes en The max possible number of programmes is illustrated in this overview The corresponding programmes for your appliance can be found on the fascia Type of utensils Type of soiling Programme Possibleadditional Programme seguence options Prerinse very adhesive TI Clean 70 pots and pans burned in or dried on a Intermediate rinse non sensitive food remnants Intensive 70 Final rinse 65 utensils containing starch Dr and cutlery or protein a quo Is optimised according to all the soiling with the aid Auto 45 65 of sensors Prerinse mixed utensils part dried common Uo Clean 50 and cutlery household food ete Intermediate rinse remnants Eco 50 Final rinse 65 Dry Intensive zone Prerinse Express Wash Clean 40 sensitive utensils Yo Y i Intermediate rinse A slightly adhesive Gentle 40 Half load Final rinse 55 sensitive plastic reS ene Extra drying Dry and glasses Uo T Clean 45 _ gt D 3 i P 1 Extra drying Intermediate rinse Quick 45 Final rinse 55 cold rinsing TN 7 AM all types of utensils intermediate y none Prerinse cleaning Prerinse Programme
22. oiled utensils in the upper basket The spray pressure in the lower basket is intensified the rinsing temperature is increased slightly Extra drying An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better There is a slight increase in the energy consumption 16 Washing the dishes Programme data The programme data consumption values can be found in the summary of instructions They refer to normal conditions and the water hardness set value 4 14 Different influencing factors such as e g water temperature or line pressure may result in deviations Aqua sensor depending on model The Aqua sensor is an optical measuring device light barrier which measures the turbidity of the rinsing water The Aqua sensor is used according to the programme If the Aqua sensor is active clean rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 3 6 litres If the turbidity is greater the water is drained and is replaced with fresh water In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling Switening on the appliance Turn on the tap fully Switch on ON OFF switch 1 Rotate programme selector L 3 reguired programme The expected programme duration flashes on the digital display 5 Press START button L 4 The programme starts running
23. oor 17 n FD a L Rely on the expertise of the manufacturer Call us to ensure that the repair will be carried out by fully trained service engineers who are equipped with original spare parts for your appliance en Installation The dishwasher must be connected correctly otherwise it will not function properly The specifications for the inlet and outlet as well as the electrical connected loads must correspond with the required criteria as specified in the following paragraphs or in the installation instructions Install the appliance in the correct sequence Checking appliance on delivery Installing the appliance Waste water connection Fresh water connection Electrical connection poten instructions Install and connect the appliance according to the installation and assembly instructions Prior to installation disconnect the dishwasher from the power supply Ensure that the protective conductor system of the domestic supply has been correctly installed The electrical connection conditions must correspond with the specifications on the dishwasher rating plate 32 Ifthe power cord of this appliance is damaged it must be replaced with a particular power cord To prevent injury the power cord may be replaced by customer service only If the dishwasher is installed in a high sided unit the unit must be secured properly Install built under or int
24. ot resistant to heat Copper and tin utensils Utensils which are soiled with ash wax lubricating grease or ink Aluminium and silver parts have a tendency to discolour and fade during the wash cycle Even some types of glass e g crystal glass objects may turn cloudy after many wash cycles Glass and utensil damage Causes Glass type and glass production process Chemical composition of the detergent Water temperature of the wash programme Recommendation Use only glasses and porcelain which the manufacturer designates as dishwasher proof Use a detergent which protects utensils Take glass and cutlery out of the dishwasher as soon as possible after the programme ends en Loading the dishwasher Remove large food remnants It is not necessary to prerinse utensils under running water Place the utensils so that they are secure and cannot tip over all utensils with their openings face down parts with curves or indentations are at an angle thereby allowing water to drain does not obstruct rotation of the two spray arms 23 and 24 Very small utensils should not be washed in the machine as they may fall out of the baskets Unloading the dishwasher To prevent water from dripping off the upper basket onto the utensils in the lower basket it is recommended to empty the appliance from the bottom up Hot utensils are sensitive to shock Therefore when
25. pected programme duration is indicated on the numerical display 5 Press START button 4 Programme seguence starts After approx 4 minutes press the START button 4 until 2 fis indicated on the digital display After approx 1 min is indicated on the digital display 2 37 Switch the appliance off _1 the tap off Transport appliance upright only This prevents residual water from running into the machine control and damaging the programme sequence and turn Protection against frost If the appliance is in a room where there is a risk of frost e g holiday home empty the appliance completely see Transportation Turn off the tap disconnect supply hose and drain water 26 Waste disposal Both the packaging of new appliances and the old appliances themselves contain valuable raw materials and recyclable materials Please dispose of the individual parts separated according to type Please ask your dealer or inquire at your local authority about current means of disposal Packaging All plastic parts of the appliance are identified with internationally standardised abbreviations e g gt PS lt polystyrene Therefore plastic waste can be sorted out when the appliance is being disposed of Please follow the safety instructions under Delivery Old appliances Please follow the safety instructions under Disposal of
26. r cannot be closed and the upper spray arm will not be connected to the water circuit Top basket with upper and lower roller pairs Pull out the top basket 20 out Remove the upper basket and re attach it to the upper stage 3 or lower stage 1 rollers 12 Detergent You can use tablets as well as powder or liquid detergents for dishwashers but never use washing up liquid The dosage can be individually adjusted with powder or a liquid detergent according to the degree of soiling Tablets contain an adequately large amount of active ingredients for all cleaning tasks Modern powerful detergents predominantly use a low alkaline formulation with phosphate and enzymes Phosphates bond the lime in the water Enzymes break down starch and remove protein Phosphate free detergents are less frequent These have a slightly weaker lime bonding capacity and require a higher dosage To remove coloured stains e g tea tomato sauce oxygen based bleaching agents are usually used Note To ensure a good washing result always follow the instructions on the detergent packaging If you have further questions we recommend that you contact the detergent manufacturers helpline A Warning Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents Adding detergent If the detergent dispenser 30 is still closed press
27. s water damage we will make good the damage for private users To ensure water damage protection the appliance must be connected to the power supply 2 This liability guarantee is valid for the service life of the appliance 3 A prereguisite for the warranty claim is that the appliance has been correctly installed and connected with AguaStop according to our instructions This also includes the correct installation of the AguaStop extension original accessory Our warranty does not extend to defective feed lines or fittings up to the AguaStop connection on the tap 4 If your appliance is fitted with AguaStop you can leave your appliance unattended during operation and leave the tap turned on afterwards The tap should only be turned off if you are absent from home for a prolonged period e g several weeks holiday Repair order and advice on faults GB 0844 8928979 Calls from a BT landline will be charged at up to 3 pence per minute A call set up fee of up to 6 pence may apply IE 01450 2655 US 800 944 2904 toll free Contact information for all countries can be found on the enclosed customer service list Robert Bosch Hausgerate GmbH Carl Wery StraBe 34 81739 M nchen Germany www bosch home com 9000574748 en 9111 640EG
28. se for washing domestic dishes Children or people whose physical sensory or mental abilities prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person Do not lean or sit on the open door The appliance could tip Please note that free standing appliances may tip over if the baskets are overloaded Do not add any solvents to the washing chamber Danger of explosion Open the door carefully when the programme is still running There is a risk of hot water spraying out of the appliance To prevent injuries e g caused by stumbling open the dishwasher only briefly in order to load and unload the dishwasher Read and observe the safety information and instructions for use on the packaging for cleaning and rinsing agents A Warning Knives and other utensils with sharp points must be placed in the cutlery basket with the points downwards or horizontally on the knife shelf depending on model Children in the household If fitted use the childproof lock An exact description can be found in the back of the envelope Do not allow children to play with or operate the appliance Keep children away from detergents and rinse aid These may cause chemical burns in the mouth throat and eyes or asphyxiation Keep children away from open dishwasher The water in the rinsing compartment is not drinking water and could contain det
29. the programme ends leave the utensils to cool down in the dishwasher until they can be handled Cups and glasses Top basket 20 LZ a en Pans Bottom basket 28 Tip Heavily soiled utensils pans should be placed in the bottom basket The more powerful spray jet provides a better dishwashing result Tip Other examples such as the best way of loading your dishwasher can be found on our homepage as a free download The corresponding Internet address can be found on the back page of these instructions for use Cutlery basket You should always place cutlery unsorted with the points downwards To prevent injuries place long pointed implements and knives on the knife shelf Etagere The etagere and the space underneath can be used for small cups and glasses or for larger items of cutlery such as wooden spoons or serving cutlery The etagere can be folded up if not required Depending on the model a 3 fold height adjustment is possible To do this first place the etagere vertically and pull up then place at a slight angle push down to the required height 1 2 or 3 and snap into place Folding spikes depending on model The spikes can be folded down to improve arrangement of pans bowls and glasses Small accessories holder depending on mo
30. tion only up to a specific degree of hardness usually 26 Clarke Over this limit salt and rinse aid must be added As soon as combined detergents are used the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result A Warnings Do not place small parts for washing in the tablet collecting tray L22 I this prevents the tablet from dissolving evenly lf you want to add more utensils after the programme has started do not use the tablet collecting tray L22 as a handle for the upper basket The tablet could already be there and you will touch the partially dissolved tablet 13 en Notes You will obtain optimum rinsing and drying results by using solo detergents and applying salt and rinse aid separately If programmes are short tablets may not have full cleaning effect due to different dissolving properties and there may even be undissolved detergent residue It is recommended to use washing powder for these programmes The Intensive programme on some models requires one tab only When using washing powder you can apply some of this cleaning agent to the inside of the appliance s door Even if the rinse aid and or salt refill indicator is lit the rinse programme will run correctly with combined detergents If using detergents in a water soluble protective cover Take hold of the cover with dry hands only and put the detergent i
31. ually be omitted up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l If the water hardness is over 21 dH special salt must be used Switching off salt refill indicator water softening system If the salt refill indicator L 9 is impaired e g when using combined detergents containing salt component it can be switched off Proceed as described under Adjusting the water softening system and set the value to H 00 The water softening system and salt refill indicator are now switched off A Warning Never fill the salt dispenser with detergent You will destroy the water softening system en Rinse aid gt lt As soon as the rinse aid refill indicator 8 is lit on the fascia there is still a rinse aid reserve of 1 2 rinsing processes Refill with rinse aid The rinse aid is required for stain free utensils and clear glasses Use only rinse aid for domestic dishwashers Combined detergents with rinse aid component may be used up to a water hardness of 21 dH 37 fH 26 Clarke 3 7 mmol l only If the water hardness is over 21 dH rinse aid must be used Open the dispenser 29 by pressing and lifting the plate on the cover Carefully pour rinse aid up to the max mark in the filler opening Close cover until it clicks shut To prevent excessive foam formation during the next rinse cycle remo
32. ve any rinse aid which has run over with a cloth Setting amount of rinse aid The amount of rinse aid can be set from G0 to 7 06 Please set rinse aid on 7 05 to obtain very good drying results 05 is already set in factory Change this setting only if streaks select lower setting or water stains select higher setting are left on the utensils Close the door Switch on ON OFF switch L 1 Press and hold down the START button L 4 Rotate programme selector L 3 until 17 s indicated on the digital display L 5 Release button The factory set value 5 is lit on the digital display L 5 To change the setting Rotate programme selector L 3 until the reguired value is indicated on the digital display L 5 Press START button 4 The set value is saved Switching off rinse aid refill indicator If the rinse aid refill indicator 8 is impaired e g when using combined detergents containing rinse aid component it can be switched off Proceed as described under Setting amount of rinse aid and set the value to rad The rinse aid refill indicator 8 switched off is now Utensils Not suitable Cutlery and utensils made of wood Delicate decorative glasses craft and antique utensils These decors are not dishwasher proof Plastic parts n
33. witch on ON OFF switch 1 Press and hold down the START button 4 Rotate programme selector L 3 until H i is indicated on the digital display L5 Release button The factory set value H 74 is lit on the digital display L 5 To change the setting Rotate programme selector L 3 until the reguired value is indicated on the digital display L 5 Press START button 4 The set value is saved Water hardness table Water Hardness range ft I x i ft N I medium 157166 13 15 medium 1 9 2 1 16 20 medium 2 2 2 9 226 hard 310593 7 27 38 hard 3 8 5 4 39 62 hard 568 9 Special salt S Using special salt Always refill with special salt immediately before switching on the appliance This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank Open the screw type cap of the compartment 25 Fill the tank with water only required when switching on the appliance for the first time Then add dishwasher salt not table salt or tablets The water is displaced and runs out As soon as the salt refill indicator L9 on the fascia is lit top up the salt depending on model en Using detergents with salt component If combined detergents with a salt component are used salt can us
34. y residue and clean filters under running water Re nstall filter system in reverse sequence and ensure that the arrow marks are opposite each other after closing the filter system en Spray arms Limescale and contaminants in the rinsing water may block nozzles and bearings on the spray arms 23 and 24 Check outlet nozzles on the spray arms for blockages Unscrew the upper spray arm 23 Remove the lower spray arm 24 upwards Clean spray arms under running water Re engage or screw on spray arms 19 en Troubleshooting The majority of faults which could occur in daily operation can be rectified by the user This ensures that the appliance is guickly available for use again The following overview will help you locating the causes and gives helpful advise to eliminate them Note If the appliance stops during dishwashing or does not start for no obvious reason first run the Abort programme function Reset See chapter entitled Dishwashing A Warning If on the digital display L 5 an error code E 0 i to E 32 always disconnect the appliance from the power supply and then turn off the tap You can rectify certain faults yourself see following fault description for all other faults please contact customer service and state the indicated fault XX A Warning Don t forget Repairs may be carried out by tec
35. your appliance This appliance is identified x according to the European guideline 2002 96 EC on waste electrical and electronic eguipment WEEE The guideline specifies the framework for an EU wide valid return and re use of old appliances Subject to changes Childproof lock door lock a F 22 40 V ors 41 40 Activate the childproof lock 41 Open the door with activated childproof lock 42 Deactivate childproof lock Baking sheet spray head 42 Always close the appliance door completely when you leave the appliance This is the only way you can protect your children from potential dangers gourmet plates pasta plates dinner plates can be cleaned with the aid of the spray head To do this remove the top basket and insert the spray head as illustrated in the diagram To ensure that the spray jet can reach all parts arrange the baking sheets as illustrated max 4 baking sheets and 2 grilles Never operate the dishwasher without the top basket or baking sheet spray head some models AguaStop guarantee does not apply to appliances without AguaStop In addition to warranty claims against the seller based on the purchase contract and in addition to our appliance warranty we will pay damages under the following conditions 1 If our AguaStop system is defective and cause
Download Pdf Manuals
Related Search