Franke Swivel Spout
Contents
1. FRANKE ROTAFLOW TAP INSTALLATION INSTRUCTIONS KITCHEN SYSTEMS Guarantee Your Franke mixer has been manufactured to the high standard you would expect of any Franke product but in the unlikely event that you should experience any defect in the materials or workmanship within one year of purchase we will replace the faulty part free of charge This is provided the mixer has only been used for normal domestic purposes in the UK and that the care installation and maintenance instructions have been observed You should also retain your dated invoice as proof of purchase to validate any claims under our guarantee This one year guarantee is extended to five years in the case of the valve mechanism Normal wear and tear is excluded from the guarantee Decorative surface finishes are guaranteed for one year from the date of purchase provided our advice concerning care has been observed and no scouring agents have been used Scuffs and scratches caused by improper installation or accidental damage are not covered by this guarantee Neither are slight shade variations or any damage or defect caused by incorrect installation or abuse of the fitting Design This mixer is available in Chrome and SilkSteel to complement all Franke sinks Service For spare parts servicing or any other queries visit www franke co uk Preparation First shut off your water heating system then with your mains sto2. UT SILKSTEEL SWIVEL amp AERATOR CHROME COMPLETE SWIVEL 8 AERATOR SILKSTEEL COMPLETE FIXING NUT CHROME FIXING NUT SILKSTEEL O RING KIT VALVE COVER CHROME VALVE COVER SILKSTEEL HOT HANDLE CHROME COLD HANDLE CHROME HOT HANDLE SILKSTEEL COLD HANDLE SILKSTEEL COMPRESSION VALVE SET OF COPPER TAILS FIXING KIT 1499R 1234R 1492R 1499R CH 1499R SS 1498R CH 1498R SS 1243R CH 1243R SS 1239R 3412R CH 3412R SS 1955R H CH 1955R C CH 1955R H SS 1955R C SS 3768R 1234R 1492R Ni eee Franke UK Limited West Park MIOC Styal Road Manchester M22 5WB Tel 44 0 161 436 6280 Fax 44 0 161 436 2180 Email info ukQfranke com For spare parts servicing or any other queries visit www franke co uk KITCHEN SYSTEMS
3. hat there are no leaks switch on the water heating Warning These hints have been prepared for your guidance you must exercise due care at all times We do not accept responsibility for any problems that may occur through incorrect installation How to care for your kitchen sink mixer To maintain the appearance of this fitting ensure it is cleaned only using a clean soft damp cloth A solution of warm water and mild liquid detergent may be used where necessary and then the fitting rinsed thoroughly Abrasive cleaners or acidic cleaners MUST NOT BE USED under any circumstances Avoid contact with all solvents Technical Data Minimum water pressure 7 25 PSI 0 5 bar Maximum water pressure 75 PSI 5 bar Maximum hot water temperature 70 C Recommended hot water temperature 65 C Note If these temperatures or water pressures are exceeded damage to the tap can result A pressure reducing valve may be required to be fitted in high water pressure situations NB If for any reason the spout is removed from the tap care must be taken when reinserting the spout into the body to ensure that the Grub Screw is located in the split of the white PTFE ring PARTS LIST AS FOLLOWS 133 0069 255 133 0069 265 133 0069 256 133 0069 266 133 0085 007 133 0150 095 133 0069 151 133 0069 381 133 0069 385 133 0255 893 133 0255 894 133 0255 895 133 0255 896 133 0255 897 133 0069 184 133 0068 819 SPOUT CHROME SPO
4. pcock closed open the lowest hot and cold taps in the house and allow to run until the cold storage tank and pipes are empty the hot water storage cylinder always remains full Installation First screw the threaded stud into the mixer body Screw the copper tails into the mixer body and fully hand tighten After making any necessary alterations to existing pipework fit in position The O ring should be placed in the recess of the body to make a seal with the sink When the tap is in position with the cold side on the right when viewed from the front slide the nylon bracing plate up to the underside of the sink together with the retaining plate and secure by screwing the fixing nut finger tight Check that the mixer body is correctly positioned and fully tighten fixing nut It is recommended that 15mm x 15mm compression fittings be used to connect mixer to supply pipes Cold is connected to the right and hot on the left when viewed from the front Attention Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any remaining swarf solder or other impurities Failure to carry out this simple procedure could cause problems or damage to the workings of the mixer Having first checked all new connections turn on the mains stopcock close all taps except the new mixer and as the system starts to refill check for leaks Once you have satisfied yourself t
Download Pdf Manuals
Related Search