Franke Swivel Spout
Contents
1. FRANKE SION TAP INSTALLATION INSTRUCTIONS KITCHEN SYSTEMS Guarantee Your Franke mixer has been manufactured to the high standard you would expect of any Franke product but in the unlikely event that you should experience any defect in the materials or workmanship within one year of purchase we will replace the faulty part free of charge This is provided the mixer has only been used for normal domestic purposes in the UK and that the care installation and maintenance instructions have been observed You should also retain your dated invoice as proof of purchase to validate any claims under our guarantee This one year guarantee is extended to five years in the case of the valve mechanism Normal wear and tear is excluded from the guarantee Decorative surface finishes are guaranteed for one year from the date of purchase provided our advice concerning care has been observed and no scouring agents have been used Scuffs and scratches caused by improper installation or accidental damage are not covered by this guarantee Neither are slight shade variations or any damage or defect caused by incorrect installation or abuse of the fitting Design This mixer is available in Chrome and SilkSteel to complement all Franke sinks Service For spare parts servicing or any other queries visit www franke co uk Preparation First shut off your water heating system the2. close all taps except the new mixer and as the system starts to refill check for leaks Once you have satisfied yourself that there are no leaks switch on the water heating Warning These hints have been prepared for your guidance you must PARTS LIST AS FOLLOWS exercise due care at all times We do not accept responsibility 133 0251 377 ANTISPLASH CHROME 1268R CH for any problems that may occur through incorrect installation 133 0251 378 ANTISPLASH SILKSTEEL 0 1268R SS 93 0291 972 aap POUT CHROME one STOIR CM aas How to care for your kitchen sink mixer L IL MIMMI a To maintain the appearance of this fitting ensure it is cleaned 33 0069 151 O RING KIT 1239R oniv using a clean soft damp cloth A solution of warm water 133 0251 381 HOT HANDLE CHROME 3732R H CH and mild liquid detergent may be used where necessary and 1133 0251 382 COLD HANDLE CHROME 3732R C CH then the fitting rinsed thoroughly Abrasive cleaners or acidic 133 0251 383 HOTHANDLE SILKSTEEL 3732R H SS cleaners MUST NOT BE USED under any circumstances 133 0251 384 COLD HANDLE SILKSTEEL 3732R C SS Avoid contact with all solvents 133 0150 220 HOT VALVE 3308R H 133 0150 219 COLD VALVE 3308R C Technical Data 133 0251 385 BASE PLINTH CHROME 3738R CHO Minimum water pressure 7 25 PSI 0 5 bar 132 0251386 BASE PLINTH SILISTEEL 37838158 Maximum water pressure 75 PSI 5 bar 133 0150 221 FIXING KIT 3311R Maximum hot wate
3. n with your mains stop cock closed open the lowest hot and cold taps in the house and allow to run until the cold storage tank and pipes are empty the hot water storage cylinder always remains full Installation First screw the threaded stud into the mixer body Screw the flexi tails into the mixer body and fully hand tighten After making any necessary alterations to existing pipework pass the plinth over the flexi tails and fit in position The shaped upstand on the plinth will locate in the tap body and the O ring should be placed in the recess to make a seal with the sink When the tap is in position with the cold side on the right when viewed from the front slide the nylon bracing plate up to the underside of the sink together with the retaining plate and secure by screwing the fixing nut finger tight Check that the mixer body and plinth are correctly positioned and fully tighten fixing nut It is recommended that 15mm x 15mm compression fittings be used to connect mixer to supply pipes Cold is connected to the right and hot on the left when viewed from the front Attention Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any remaining swarf solder or other impurities Failure to carry out this simple procedure could cause problems or damage to the workings of the mixer Having first checked all new connections turn on the mains stop cock
4. r temperature 70 C 133 0251 361 FLEXI TAILS 3728R Recommended hot water temperature 65 C Note If these temperatures or water pressures are exceeded damage to the tap can result A pressure reducing valve may be required to be fitted in 1268R 18 high water pressure situations 3731R NB If for anv reason the spout is removed from the tap 1239R b care must be taken when reinserting the spout into the bodv to ensure that the Grub Screw is located in the split of the white PTFE ring ii 3732R H a 9 0 l cs Cu a ai 3732R C 3308R H sj 3308R C 3728R Franke UK Limited West Park MIOC Styal Road Manchester M22 5WB Tel 44 0 161 436 6280 Fax 44 0 161 436 2180 Email info uk franke com For spare parts servicing or any other queries visit www franke co uk KITCHEN SYSTEMS
Download Pdf Manuals
Related Search