JBL EON EON615/230 loudspeaker
Contents
1. Floor Monitor Floor Standing Tripod Stand Stacking Pole Mount The following guidelines will help you achieve optimum sound wherever you use your EON loudspeakers Only experienced professionals should attempt to suspend the speakers For permanent installation applications utilizing the M10 suspension points JBL Professional recommends the use of three 3 M10 x 1 5 thread pitch forged shoulder steel eyebolts with an 18 20mm threaded shaft along with fender washers rated for overhead suspension Users unfamiliar with safe rigging practices should not attempt to suspend loudspeakers Please see httos www jbloro com pub technote tn_v1n14 pdf for more information Raise the speakers as high as possible For best results try to get the high frequency horn at least 2 to 4 feet above the heads of the audience If the speakers are too low the people in the back of the audience will not receive the best quality sound Place the speakers between the microphones and the audience Feedback occurs when the microphones pick up sound from the speakers and feed the sound back through the sound system If space is limited point the speakers away from the microphones to reduce feedback Locate the speakers away from turntables Low frequency feedback occurs when the output of the speaker is picked up by the tone arm of the turntable and is re amplified A heavy solid turntable base and sho2. S gt 2 7 a MASTER VOLUME 430W Max JBL PROFESSIONAL 100 120VAC 50 60Hz NORTHRIDGE CA USA 230 240VAC 50 60Hz mum HARMAN FUSE TYPE T3 18L250V FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH SAME TYPE OF RATING AHARMAN INTERNATIONAL COMPANY DESIGNED AND ENGINEERED IN THE USA MODEL 0 615 SERIAL NO WARNING SHOCK HAZARD DO NOT OPEN THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES 4 OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS AVIS RISQUE DE ELECTRIQUE NE PAS OUVRIR 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION C e mmm Made in Mexico 430W Max JBL PROFESSIONAL 100 120VAC 50 60Hz NORTHRIDGE CA USA 230 240VAC 50 60Hz pem HARMAN FUSE TYPE T3 15L250V FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH SAME TYPE OF RATING A HARMAN INTERNATIONAL COMPANY DESIGNED AND ENGINEERED IN THE USA SMALL PA USING BOTH INPUTS AND THRU FUNCTION CH1 input set to Mic CH2 input set to Line EQ Preset Main 19 APPLICATION EXAMPLES 20 D c3 c3 c3 c3 o ia BLUETOOTH O JBL O PROFESSIONAL FRONTLED MAIN EG PRESETS MONITOR sus SPEECH EON SIS e e SIGNAL LIMIT SIGNAL wt
3. Front View Left View Rear View 11 610 SPECIFICATIONS System Specification oystem Type Maximum SPL Output Frequency Range 10 dB Frequency Response 3 dB EQ Amplification Amplifier Design oystem Power Rating Input Impedance Line Input Gain Mic Input Gain Connectors LED Indicators Cooling AC Power Input AC Power Consumption 120VAC Speaker Specification LF Driver HF Driver Coverage Pattern Crossover Frequency Enclosure Material suspension Mounting Handles Finish Grille Dimensions H x W x D Gross Weight 12 67 in Bottom View 12 Self powered 10 two way bass reflex 124 dB 52 Hz 20 kHz 60 Hz 20 kHz 3 Parametric EQ s High and Low Shelf Available via Bluetooth app only High Efficiency Class D 1000W Peak 700 LF 300HF 500W Continuous 350W LF 150W HF 20K ohms Balanced Infinity to 26 8dB 14dBu max input level Infinity to 29dB in addition to line input gain 2 x Balanced XLR 1 4 combination inputs 1 x male XLR loop thru out Power Bluetooth EQ Preset EQ Signal CH1 Signal CH2 Limit Passively Cooled No Fan 100 120VAC 50 60Hz 230 240VAC 50 60Hz 1 8th Power 1 14A 1 4th Power 1 714 Max 1 3rd Power 2 03A Max 1 x JBL 610H 322mm 10 in woofer 1 x JBL 2414H 1 25 4mm 1 in polymer diaphragm neodymium compression driver 1109 H x 60 V nominal 1 8 kHz Polypropylene
4. Power LED This LED White lights to indicate that the speaker is plugged in and switched ON Front LED On Off Toggles the LED Blue on front of speaker On or Off EQ Button Once enabled via the app the EQ toggles the applied EQ settings on off CH1 amp CH2 Signal Indicators The SIGNAL LEDs Green illuminates to indicate a usable signal is present at connected INPUTS Limit Indicator The LIMIT LED Red illuminates to indicate that the system is approaching limit If this LED is on for more than the duration of brief dynamic peaks the system is being over driven Continuously over driving the system will result in unpleasant and fatiguing distortion and may lead to premature failure of your speaker system Master Volume Controls the master volume of the unit By turning the knob counter clockwise you will be lowering the overall volume of the speaker By turning the control clockwise you will be increasing the overall volume of the speaker CH1 amp CH2 Gain Controls the gain of CH1 amp CH2 respectively By turning the signal counter clockwise you will be lowering the gain of your source material By turning the control clockwise you will be increasing the gain 17 LOUDSPEAKER PLACEMENT AND SUSPENSION 18 Suspended
5. SMALL PA USING TWO SYSTEMS AS MONITORS CH1 input set to Mic CH2 input set to Line EQ Preset Monitor 3 Mm e CAUTI RSK OF ELECTRIC SHOCK DONDE OPEN WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ER e Made in Mexico JBL PROFESSIONAL NORTHRIDGE CA USA A HARMAN INTERNATIONAL COMPANY DESIGNED AND ENGINEERED IN THE USA APPLICATION EXAMPLES BLUETOOTH JBL O PROFESSIONAL MAIN EQ PRESETS MONITOR SUB SPEECH ON SI e e SIGNAL LIMIT wally SANG lt MASTER VOLUME MODEL 0 615 SERIAL NO THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 430W Max 100 120VAC 50 60Hz 230 240VAC 50 60Hz FUSE TYPE T3 15L250V FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH SAME TYPE OF RATING ON FRONT LED EG O WARNING SHOCK HAZAR NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ce Made in Mexico JBL PROFESSIONAL NORTHRIDGE CA USA HARMAN AHARMAN INTERNATIONAL COMPANY DESIGNED AND ENGINEERED IN THE USA 2 BLUETOOTH O O EG PRESETS MONITO MAIN SUB S
6. OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE 18 Do not expose this equipment to dripping or splashing and ensure that no objects filled with liquids such as vases are placed on the equipment 19 The mains plug of the power supply cord shall remain readily operable DECLARATION OF CONFORMITY Safety And EMC Compliance Specifications EN 55103 1 1997 Electromagnetic Compatibility Product Family Standard for Audio Video Audio Visual and Entertainment Lighting Control Apparatus for Professional Use Part 1 Emissions EN 55103 1 1997 Magnetic Field Emissions Annex A 10 cm and 20 cm EN 55022 2003 Limits and Methods of Measurement of Radio Disturbance Characteristics of ITE Radiated Class B Limits Conducted Class A EN 55103 2 1997 Electromagnetic Compatibility Product Family Standard for Audio Video Audio Visual and Entertainment Lighting Control Apparatus for Professional Use Part 2 Immunity EN 61000 4 2 A2 2001 Electrostatic Discharge Immunity Environment E2 criteria B 4 kV Contact 8 kV Air discharge EN 61000 4 3 2003 Radiated Radio frequency Electromagnetic Immunity Environment E2 criteria A EN61000 4 4 2005 Electrical Fast Transient Burst Immunity criteria B EN 61000 4 5 2001 Surge Immunity criteria B EN 61000 4 6 1996 Immunity to Conducted Disturbances Induced by Radio Frequency Fields criteria A EN 61000 4 11 2004 Voltage Dips Short Interruptions and Voltage Var
7. 00 Family Coverage Patterns Compared to a Typical Speaker B TYPICAL B TYPICAL B TYPICAL E EONG15 EONG 12 E EONG 10 The EON600 s extraordinary performance results from a breakthrough approach to waveguide design JBL engineers examined the radiation characteristics of the EON s high and low frequency drivers at 36 different points employing JBL s exclusive state of the art measurement techniques then designed individual waveguides for both components that control the sound radiation at the high frequencies the crossover point and at the low frequencies Special fluting is designed into the structure that guides the frequencies through the full range of the system The result is consistent response throughout its 90 degree coverage pattern The quality and consistency between on axis and off axis response delivers uniform coverage and high intelligibility throughout the coverage area which means the EON600 s smooth transparent sound is the same for the entire audience Coverage through Revolutionary Waveguides Image Control Waveguide Low Frequency Waveguide Increased High Frequency detail The Image Control JBL s ground breaking new low frequency waveguide Waveguide s patent pending design precisely controls the features special fluting that is designed into the structure that sound emanating from the EON600 in the vertical and guides the frequencies through the full range of the system horizontal planes ensuring the representation o
8. 1 x male XLR loop thru out Power Bluetooth EQ Preset EQ Signal CH1 Signal CH2 Limit Passively Cooled No Fan 100 120VAC 50 60Hz 230 240VAC 50 60Hz AC Power Consumption 120VAC 1 8th Power 1 14A 1 4th Power 1 71A Max 1 3rd Power 2 03A Speaker Specification LF Driver HF Driver Coverage Pattern Crossover Frequency Enclosure Material suspension Mounting Handles Finish Grille Dimensions H x W x D Gross Weight Bottom View 10 1 x JBL 615H 380mm 15 woofer with 2 voice coil 1 x JBL 2414H 1 25 4mm 17 annular polymer diaphragm neodymium compression driver 90 H x 60 V 1 8kHz Polypropylene multi purpose main amp monitor 36mm pole socket with stabilizing screw 3 x M10 suspension points One left one right one top one bottom 4 total Black Granite Powder coated perforated steel with acoustically transparent screen backing 707mm x 439mm x 365mm 27 8 x 17 3 x 14 4 17 69 kg 39 Ibs I cope CUM Front View Left View Rear View EON612 SPECIFICATIONS System Specification system Type Maximum SPL Output Frequency Range 10 dB Frequency Response 3 dB EQ Amplification Amplifier Design System Power Rating Input Impedance Line Input Gain Mic Input Gain Connectors LED Indicators Cooling AC Power Input AC Power Consumption 120VAC Speake
9. AME TYPE OF RATING m ON OFF a FRONT LED 4 SIGNAL Wily M 7 7 x NS GAIN WN MIC ee ine v A ud RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING SHOCK HAZARD DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR ce Z O Made in Mexico JBL PROFESSIONAL NORTHRIDGE CA USA HARMAN AHARMAN INTERNATIONAL COMPANY DESIGNED AND ENGINEERED IN THE USA Power LED Front LED On Off EQ Button Ch1 amp Ch2 Signal Indicators Limit Indicator Master Volume Chi amp Ch2 Gain BACK PANEL Bluetooth Sync Depress this button in order to initiate pairing with your Bluetooth enable device Bluetooth Indicator This LED will illuminate blue to indicate that your Bluetooth connection is established Bluetooth Boot Depress this button to reset the pairing with your Bluetooth enabled device without having to turn the speaker off EQ Presets Use this button to toggle through the four different settings MAIN This is the default setting for the EON600 loudspeakers Use this setting when your 600 loudspeaker is being used either on a tripod or pole and facing towards your audience MONITOR Use this setting when your 600 loudspeaker is being used as a stage monitor facing towards you SUB Use this setting when your 600 loudspeaker is being used in conjunction with a separate subwoofer This preset enables a High Pass Filter HPF set a
10. EON eo LJser s Guide pao eie EON eio by HARMAN CONTENTS Safety Instructions Declaration Of Conformity Quick Setup Guide Overview EON Family EON Family Block Diagram EON615 Specifications EON612 Specifications EON610 Specifications Purposeful Product Design Coverage Bluetooth Integration Back Panel Loudspeaker Placement and Suspension Application Examples Trouble Shooting Warranty Information Contact Information oco oo a A 10 11 12 13 14 15 16 18 19 22 23 24 SAFETY INSTRUCTIONS Before You Begin Important Information Before using your EON speaker system please review the following for important information on safety and protection of your investment in quality loudspeakers 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with dry cloth 7 Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong is
11. IGNAL YSN 4 v GAIN TEOG Vene LINE ME VOLUME MODEL EONG15 SERIAL THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 42 THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 430W Max 100 120VAC 50 60Hz 230 240VAC 50 60Hz FUSE TYPE 3 151250 FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH SAME TYPE OF RATING SMALL PA USING EXTERNAL MIXE CH1 amp CH2 Mic Line inputs set to Line EQ Preset Main FRONT LED e EG WARNING SHOCK HAZARD OT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR Made JBL PROFESSIONAL NORTHRIDGE CA USA HARMAN A HARMAN INTERNATIONAL COMPANY DESIGNED AND ENGINEERED IN THE USA 21 TROUBLE SHOOTING Symptom Likely Cause What to do Speaker not connected T to active AC power Verify that speaker is connected and that the circuit is on Power not switched on Switch on power and verify that power LED is on No sound speaker is connected 22 to working AC power but won t come on No sound Speaker comes on No sound with microphone connected directly to the MIC LINE input Signal sounds distorted and very loud PEAK light is lit most of the time Signal sounds distorted even at moderate vol
12. LASTS AND OR DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO YOU THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE JBL Professional 8500 Balboa Blvd Northridge CA 91329 USA 23 CONTACT INFORMATION 24 JBL by HARMAN Mailing Address JBL Professional 8500 Balboa Blvd Northridge CA 91329 Shipping Address JBL Professional 8500 Balboa Blvd Dock 15 Northridge CA 91329 Do not return product to this address without first obtaining prior authorization from JBL Customer Service Monday through Friday 8 00am 5 00pm Pacific Coast Time in the U S A 800 8JBLPRO 800 852 5776 www jblproservice com On The World Wide Web www jblpro com Professional Contacts Outside the USA Contact the JBL Professional Distributor in your area A complete list of JBL Professional international distributors is provided at our U S A website www jblpro com 25 EON eo PROFESSIONAL Part Number 5032132 7 13 8500 Balboa Boulevard Northridge CA 91329 USA www jblpro com by HARMAN
13. ON speakers Review the Owner s Manual for your mixer and adjust controls as needed Input sensitivity gain Channel faders Master faders Once this is done review the instructions in the Quick Start section of this guide Make sure that the MIC LINE switch is in the LINE disengaged position Reduce the level settings at speaker Review the Owner s Manual for your mixer and adjust controls as needed Input sensitivity gain Channel faders Master faders Disconnect the devices that are connected to your speaker one at a time If the noise goes away the problem is with the source or the connecting cable Disconnect or mute channels one at a time to isolate the problem Refer to the owner s manual of the faulty equipment for troubleshooting help Substitute a known good cable for the suspected faulty cable e Lift the audio ground by using an XLR F to XLR M adapter on one end Re route audio cables away from AC power and lighting cables Use the balanced outputs if available of your mixer or source equipment to drive your EON speakers Use a DI direct injection box to convert your unbalanced equipment output to a balanced output Reduce the INPUT level controls and increase the output level of your source devices WARRANTY INFORMATION The JBL Limited Warranty on professional loudspeaker products except for enclosures remains in effect for five years from the date of th
14. ck mounting can also reduce this type of feedback in DJ applications Use more speakers in large or highly reverberant spaces opreading speakers throughout these spaces will produce much better sound than trying to compensate with loudness level or equalization For very long distances the use of another set of speakers with time delay is recommended otand speakers upright for PA Tilt the speakers back on the side for stage monitoring Upright stance provides even coverage over a wide area EON speakers are also designed with two slanted positions for stage monitoring applications APPLICATION EXAMPLES BLUETOOTH JBL O PROFESSIONAL a FRONT LED MAIN e O MONITOR SUB SPEECH EON e BLUETOOTH O JBL Q FRONT LED MASTER VOLUME MAIN EQ e PRESETS e MONITOR sus SPEECH Eu EON 6I5 e e SIGNAL LIMIT wally 7 MODEL 615 SERIAL NO CAUTION A RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING SHOCK HAZARD DO NOT OPEN THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION C e L
15. e first consumer purchase JBL amplifiers are warranted for three years from thedate of original purchase Enclosures and all other JBL products are warranted for two years from the date of original purchase Who Is Protected By This Warranty Your JBL Warranty protects the original owner and all subsequent owners so long as A Your JBL product has been purchased in the Continental United States Hawaii or Alaska This Warranty does not apply to JBL products purchased elsewhere except for purchases by military outlets Other purchasers should contact the local JBL distributor for warranty information and B The original dated bill of sale is presented whenever warranty service is required What Does The JBL Warranty Cover Except as specified below your JBL Warranty covers all defects in material and workmanship The following are not covered Damage caused by accident misuse abuse product modification or neglect damage occurring during shipment damage resulting from failure to follow instructions contained in your Instruction Manual damage resulting from the performance of repairs by someone not authorized by JBL claims based upon any misrepresentations by the seller any JBL product on which the serial number has been defaced modified or removed Who Pays For What JBL will pay all labor and material expenses for all repairs covered by this warranty Please be sure to save the original shipping cartons because a charge will be made if
16. f the following measures e Reorient or relocate the receiving antenna e ncrease the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body IC Warning 1 This device complies with Industry Canada licence exempt RSS Standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device 2 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnement QUICK SETUP GUIDE Congratulations on you
17. f your mix is neutral and accurate at the listening position BLUETOOTH INTEGRATION Speaker Discovery EON EON 615 PEQ Controls EON 615 Preset Management Visit jblpro com EON600 to register ea e Supports iOS amp Android e Bluetooth audio NOT supported Features e Bluetooth speaker discovery up to 4 at one time e Bass and Treble control Low and High Shelf EQ e PEQ 3 parametric EQ filters with control over Frequency Gain and Q e Master Volume control e Recall back panel Factory Presets Main Monitor Sub and Speech e Save and Recall User EQ Presets BACK PANEL Bluetooth Sync Bluetooth Indicator Bluetooth Boot EQ Presets Mic Line Toggle XLR 1 4 Combo Inputs XLR Male Loop Thru Power Switch 16 BLUETOOTH MAIN PRESETS MONITOR SUB SPEECH e SIGNAL LIMIT Wily Wily 7 7 7 7 D T M 7 v S 2 ipw WU GAIN A MASTER VOLUME 7 MIC ine Oen ww MODEL EON615 SERIAL NO THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 430W Max 100 120VAC 50 60Hz 230 240VAC 50 60Hz FUSE TYPE 13 15L250V FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH S
18. iation UL 6500 2nd Edition 1999 Audio Video and Musical Instruments Apparatus for Household Commercial and Similar General Use IEC 60065 2001 EN 60065 2002 1 2006 A11 2008 UL Compliance Specifications UL 60065 7th Ed CAN CSA 22 2 60065 2003 FCC Statement 1 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation 2 Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more o
19. ies in cabinet materials acoustic science transducer design and user friendliness that delivers the extraordinary quality of a high end studio monitor in a fully professional highly flexible easy to use portable system for today s working musicians and sound providers With proper care your EON Series speakers should provide you with many years of flawless performance and are flexible enough to be a part of your sound reinforcement system even as it grows in scope EON FAMILY BLOCK DIAGRAM 4 HO33dS ans JJO SOLINOIN D NO NIVIN JINNIOA pe ttes YALSVIN I 4 e wn wa EK 13 31 KS lt TVN5IS C 11 LHO 4 TVN5IS C EON615 SPECIFICATIONS System Specification system Type Maximum SPL Output Frequency Range 10 dB Frequency Response 3 dB EQ Amplification Amplifier Design System Power Rating Input Impedance Line Input Gain Mic Input Gain Connectors LED Indicators Cooling AC Power Input oelf powered 15 two way bass reflex 127 dB 39 Hz 20 kHz 50 Hz 20 kHz 3 Parametric EQ s High and Low Shelf Available via Bluetooth app only High Efficiency Class D 1000W Peak 700 LF 300HF 500W Continuous 350W LF 150W HF 20K ohms Balanced Infinity to 26 8dB 14dBu max input level Infinity to 29dB in addition to line input gain 2 x Balanced XLR 1 4 combination inputs
20. multi purpose main amp monitor 36mm pole socket with stabilizing screw 3 x M10 suspension points One left one right one top one bottom 4 total Black Granite Powder coated perforated steel with acoustically transparent screen backing 558 mm x 322 mm x 295 mm 21 968 12 677 x 11 614 11 79 kg 26 Ibs 295mm 11 60in 7 558mm 21 97 in Front View Left View Rear View PURPOSEFUL PRODUCT DESIGN Portability made easy Enclosure designs have been optimized for ideal acoustic resonance taking advantage of injection molding techniques and mechanical shaping of the enclosures This results in tremendous increases in cabinet volumes which enable better acoustic performance while maintaining the same footprint Four intelligently positioned handles make the 600 easy to carry and move around Integrated hardware mounts designed into the enclosures allow each model to be flown when required And indexed feet molded into the enclosures allow for convenient storage and transport secure stacking for stage monitor and traditional stand up configurations and unique acoustic configurations Pole Mount amp Locking Feet Suspension Points Top Handle amp Indexed Molding Side Handle Secure Stacking Monitor Position COVERAGE 14 EON6
21. or CH2 inputs 1 oelect Mic or Line via the Mic Line Button H SET OUTPUT LEVEL Using the EQ Preset E button select the appropriate preset to match your application oet the gain level for the input using the Channel Gain controls A good starting point is to set the pot at 12 o clock slowly turn Master Volume G to the right until the desired volume is reached OVERVIEW EON FAMILY EON 10 Two way multipurpose self powered sound EON eie 12 Two way multipurpose self powered sound EON 15 Two way multipurpose self powered sound reinforcement reinforcement reinforcement e 1000 Watt e 1000 Watt e 1000 Watt e 26 lbs 11 79 kg e 33 lbs 14 96 kg e 39 lbs 17 69 kg e 110 H 60 V Coverage e 100 H 60 V Coverage e 90 H 60 V Coverage Thank you for purchasing the new JBL EON More than just another great JBL sound system the new EON600 is a true step forward in technology developed specifically to deliver the best sound possible regardless of its application Completely rethinking how truly good an affordable self contained portable PA system can be JBL engineers purposely designed and built the 600 from the ground up featuring JBUs advanced waveguide technology JBL designed and manufactured transducers and convenient wireless remote control of its onboard DSP EQ parameters via Bluetooth This total redesign of the EON platform leverages the latest technolog
22. provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Service Instruction in Owner s Manual CAUTION THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO 16 To completely disconnect this apparatus from the AC mains disconnect the power supply cord plug from the AC receptacle 17 WARNING TO REDUCE THE RISK
23. r Specification LF Driver HF Driver Coverage Pattern Crossover Frequency Enclosure Material suspension Mounting Handles Finish Grille Dimensions H x W x D Gross Weight lt 14 96 Bottom View oelf powered 12 two way bass reflex 126 dB 48 Hz 20 kHz 57 Hz 20 kHz 3 Parametric EQ s High and Low Shelf Available via Bluetooth app only High Efficiency Class D 1000W Peak 700 LF 300HF 500W Continuous 350W LF 150W HF 20K ohms Balanced Infinity to 26 8dB 14dBu max input level Infinity to 29dB in addition to line input gain 2 x Balanced XLR 1 4 combination inputs 1 x male XLR loop thru out Power Bluetooth EQ Preset EQ Signal CH1 Signal CH2 Limit Passively Cooled No Fan 100 120VAC 50 60Hz 230 240VAC 50 60Hz 1 8th Power 1 14A 1 4th Power 1 714 Max 1 3rd Power 2 03A 1 x JBL 612H 380mm 12 in woofer 1 x JBL 2414H 1 25 4mm 1 in polymer diaphragm neodymium compression driver 100 H x 60 V nominal 1 8 kHz Polypropylene multi purpose main amp monitor 36mm pole socket with stabilizing screw 3 x M10 suspension points One left one right one top one bottom 4 total Black Granite Powder coated perforated steel with acoustically transparent screen backing 664 mm x 380 mm x 316 mm 26 14 x 14 96 x 12 44 14 96 kg 33 105 316mm 1244in 664 mm 26 14 in
24. r purchase of JBL Professional EON600 Series loudspeakers We know you are anxious to get up and running as fast as possible which is why you are reading this section The following will help you get set up as soon as possible Packaging Contents Your EON600 system should include the following 1 x EON600 speaker 1 x 10 3m IEC Power Cable 1 x Quick Start Guide Unbox it Open the top of the box Lay box on its side Turn box upside down then lift box up to reveal speaker Configuration Options Floor Standing Monitor Position Pole Mounted ouspended QUICK SETUP GUIDE Bluetooth Sync Bluetooth Boot EQ Presets ws amp SPEECH Mic Line Button XLR 1 4 Combo Inputs XLR Male Loop Thru Power Switch POWER IT ON Confirm the Power Switch L is in the OFF position Connect the supplied power cord to the power receptacle on the rear of the speaker Connect the power cord to an available power outlet Flip on the Power Switch L and the Power LED and the Power LED on the front of the speaker will illuminate Power LED Front LED On Off EQ On Off CH1 amp CH2 Gain Limit LED Master Volume PLUG IN THE INPUTS Turn Channel Gain Controls F and Master Volume Control all the way to the left before connecting any inputs Connect XLR or TRS cable from audio source to CH1
25. replacement cartons are requested Payment of shipping charges is discussed in the next section of this warranty How To Obtain Warranty Performance If your JBL product ever needs service write or telephone us at JBL Incorporated Attn Customer Service Department 8500 Balboa Boulevard PO Box 2200 Northridge California 91329 818 893 8411 We may direct you to an authorized JBL service Agency or ask you to send your unit to the factory for repair Either way you ll need to present the original bill of sale to establish the date of purchase Please do not ship your JBL product to the factory without prior authorization If transportation of your JBL product presents any unusual difficulties please advise us and we may make special arrangements with you Otherwise you are responsible for transporting your product for repair or arranging for its transportation and for payment of any initial shipping charges However we will pay the return shipping charges if repairs are covered by the warranty Limitation of Implied Warranties ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE ARE LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY EXCLUSION OF CERTAIN DAMAGES JBL S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT AT OUR OPTION OF ANY DEFECTIVE PRODUCT AND SHALL NOT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
26. t 100Hz SPEECH Use this setting when your 600 loudspeaker is being used for opeech only or Spoken Word only applications and is facing towards the audience Mic Line Toggle The MIC LINE buttons selects between two sensitivity ranges The buttons are used to match the input sensitivity with the output level of the devices connected to CH1 or CH2 Depressing the MIC LINE switch selects MIC High Sensitivity CAUTION Before adjusting this switch be certain to rotate the control fully counter clockwise After the MIC LINE switch has been depressed slowly rotate the control clock wise until the desired volume has been reached e Use the MIC position depressed when a microphone is connected e Use the LINE position disengaged when a line level source such as an audio mixing console audio playback device or electronic musical instrument is connected XLR 1 4 Combo Inputs These balanced inputs accepts a standard XLR female connector and also a 1 4 TRS phone plug broad range of signals from microphones audio mixing consoles and electronic musical instruments may be connected here The sensitivity of these inputs are controlled by the MIC LINE SWITCHES XLR Male Loop Thru This XLR male output connector provides a method of sending audio out to an external source If signal is present on both inputs the inputs will be summed and sent out as a 50 50 mix Power Switch Enables the AC power to the unit on and off
27. umes LIMIT light is not lit Lots of hiss in the sound the mixer controls are at very low settings Noise or hiss heard at output Hum or Buzz that increases or decreases when the mixer level controls are moved Hum or Buzz Speaker power cable is faulty or improperly connected Signal source mixer instrument etc is not sending Faulty cables and connections Microphone requires phantom power Excessive input signal trying to exceed the capabilities of the speakers Mixer or other source is overdriven Improper gain structure Noisy source device Improper A C ground or faulty equipment connected to mixer input Faulty cable between source equipment and mixer Improper A C grounding ground loops Excessively long unbalanced cable run Improper system gain structure Re seat the power cable at both ends Substitute a known good power cable Check VU meters on the source mixer Verify that the tape or CD is playing Use headphones to verify that the instrument is actually sending an audio signal Disconnect and re seat signal cables Replace suspected cable with a known good cable The EON does not supply phantom power Switch to a dynamic microphone use a battery powered microphone if possible use an external phantom power supply for condenser type microphones Reduce the output level of the source Turn down the level controls on the speaker Use additional E
28. us 2 2 2 z 2 2 4 b GAIN a LINE VOLUME w MODEL 0 615 SERIAL NO S WARNING SHOCK HAZARD DO NOT OPEN THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION C e Made in Mexico 430W Max JBL PROFESSIONAL 100 120VAC 50 60Hz NORTHRIDGE CA USA 230 240VAC 50 60Hz ped HARMAN FUSE TYPE T3 15L250V FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH SAME TYPE OF RATING TERDATIORNAL OM ESSE DESIGNED AND ENGINEERED IN THE USA BLUETOOTH O JBL O PROFESSIONAL MAIN EG PRESETS MONITOR e SPEECH EON SIS ON FRONTLED e LIMIT SIGNAL Mns 5 3 MASTER VOLUME MODEL 0 615 SERIAL NO THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE 2 THIS DEVICE MUST ACCEPT ANY INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION 430W 100 120VAC 50 60Hz 230 240VAC 50 60Hz FUSE TYPE T3 15L250V FOR CONTINUED PROTECTION AGAINST RISK OF FIRE REPLACE FUSE ONLY WITH SAME TYPE OF RATING
Download Pdf Manuals
Related Search