Sencor SRC 100 HELLO KITTY
Contents
1. SENCOR SRC 100 Hello Kitty USER S MANUAL PROJECTION ALARM CLOCK RADIO EN WARNINGS CAUTIONS AND OTHERS WARNING 1 No naked flame sources such as lighted candles should be placed on the apparatus 2 Do not place the product in closed bookcases or racks without proper ventilation 3 Where the mains plug is used as the disconnect device the disconnect device shall remain readily operable 4 The ventilation should not be imported by covering the ventilation openings with items such as newspapers table cloths curtains etc 5 It shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed on the apparatus 6 Do not connect FM antenna to outside antenna 7 The unit should not exposed to direct sunlight very high or low temperature moisture vibrations or placed in dusty environment 8 Do not use abrasive benzene thinner or other solvents to clean the surface of the unit To clean wipe it with mild non abrasive detergent solution and clean soft cloth 9 Never attempt to insert wires pins or other such objects into the vents or opening of the unit 10 Disconnect device warning Mains plug is used as the connection so it should always remain ready operate 11 Batteries shall not be exposed to excessive heat such as sunshine fire or the like 12 Class 1 LED product CAUTION Danger of explosion if battery is incorrectly replaced Replace on2. ack to AC again EN 3 GETTING STARTED TIME AND CALENDAR MANUAL SETTING A Setting Time and Calendar Press set button 7 in normal mode and keep depress over 2 seconds to enter time set mode after enter the setting mode press set button 7 to change the mode cycle as follows Normal gt Year gt Month gt Day gt 12 24H gt Real time Hour gt Real time Min gt Normal Action during data adjustment Press lt lt Tune button 8 to adjust data backward Press gt gt Tune button 12 to adjust data forward Keep depress lt lt or gt gt button for 2 seconds to enable auto forward B Setting Alarm 1 and Alarm 2 Press alarm set button 9 13 during normal mode and keep depress over 2 seconds to enter alarm set mode after enter the setting mode press alarm set button 9 13 to change the mode cycle as follows Normal gt AL 1 Hour gt AL 1 min gt AL 1 weekday Alarm gt AL 1 wake beep gt AL1 wake radio gt AL 1 radio volume gt Light gt Light intensity gt Normal Normal gt AL 2 Hour gt AL 2 Min gt AL 2 weekday Alarm gt AL 2 wake beep gt AL2 wake radio gt AL 2 radio volume gt Light gt Light intensity gt Normal Select alarm weekday mode as follows 1 5 Monday to Friday 1 7 Whole week 6 7 Saturday amp Sunday 1 1 One day of week EN 4 Action during data adjustment e Press lt lt Tune button 8 to adjust data backward Press gt gt Tune bu
3. aste Please ask your local authorities or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union If you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union If you wish to dispose of this product request the necessary information about the correct disposal method from local government departments or from your seller This product meets all the basic EU regulation requirements that relate to it Changes to the text design and technical specifications may occur without prior notice and we reserve the right to make these changes Copyright 2013 Fast CR a s Revision 08 2013 EN 9
4. ly with the same or equivalent type EN 1 FUNCTION AND CONTROLS O E O 2 3 4 18 19 14 12 16 000010 13 17 0000110 TO SET THE LIGHT INTENSITY HIGH TO SET THE LIGHT INTENSITY LOW LIGHT ON OFF MEMORY MEMORY NAP AUTO OFF DISPLAY LAMP SHADE SNOOZE SLEEP DIMMER SET TEMPERATURE EN 2 8 lt lt TUNE YEAR MONTH DAY 9 ALARM 1 ON OFF SET 10 DISPLAY 11 ON OFF 12 gt gt TUNE DST C F 13 ALARM 2 ON OFF SET 14 VOLUME UP DISPLAY AUTO CHANGE ON OFF 15 VOLUME DOWN 16 PROJECTION TIME 180 FLIP TIME TEMPERATURE 17 PROJECTION ON OFF 18 FOCUS ADJUSTMENT FOR PROJECTION UNIT 19 SPEAKER 20 FM ANTENNA 21 TEMPERATURE SENSOR IN DOOR 22 BATTERY COMPARTMENT 23 AC POWER CORD 24 RATING LABEL BACK OF UNIT LED DISPLEJ STANDBY Indicator TIME Indicator PM Indicator MHz Indicator ALARM 1 Indicator ALARM 2 Indicator POWER CONNECTION Plug the AC power cord to a household outlet AC source This unit is equipped with a battery back up system it requires a 3V CR2032 flat lithium battery not included Insert the battery in the battery compartment making certain that the positive and negative and battery terminals are attached to the corresponding terminals on the plate in the battery compartment If an AC power failure occurs the clock automatically switches to the battery power supply the clock and timer memory continue running When the AC power resumes the clock switches b
5. me will keep by 5 seconds within 5 seconds and press MEMORY SET MEMORY NAP button 4 can change the duration from 90 mins 10 mins The alarm buzzer will sound for 30 mins and then shut off automatically To stop the alarm buzzer press the ON OFF button 11 Press the MEMORY SET MEMORY NAP button 4 has no effect during alarm operation Press ON OFF button 11 to cancel NAP function Remark When using the NAP alarm did not the wake up light function PROJECTION UNIT Focus setting Adjust the projection clock brightness focus by tuning the brightness focus adjustment wheel unit the projected time is clearly shown on the ceiling or wall Adjust projected direction To flip projected image by 180 press 180 flip button 16 Converted the projection time or temperature press keep depress over 2 seconds to enter PROJECTION TIME 180 FLIP TIME TEMPERATURE button 16 Note Projects time image on the ceiling or wall of a darkened room Maximum projection distance is 3 9 feet Select DST daylight saving time mode For countries with daylight saving time DST the clock radio offers you DST option to adjust summer time In standby mode press and hold gt gt TUNE DST button 12 for 2 seconds The clock advances by one hour To exit DST mode repeat the above operation Resetting If the system does not respond or exhibits erratic or intermittent operation you may have experienced a
6. n electrostatic discharge ESD or a power surge that triggered the EN 7 internal microcontroller to shut down automatically If this occurs simply disconnect the AC power cord and remove the system backup battery wait for at least 3 minutes and then setup the unit again as if it is a brand new unit SPECIFICATIONS Frequency range 87 5 108MNz Preselection 10 channels Battery backup 3V CR2032 Flat Lithium battery x 1 not included Power supply AC230V 50 Hz Temperature range for indoor 0 to 50 C or 32 to 122 F Dimensions 140 mm x 96 mm Weight 350 g EN 8 INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Dispose of packaging material at a public waste disposal site DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES The meaning of the symbol on the product its accessory or packaging indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of w
7. play month Day Temperature the display returns to time display after 5 seconds YEAR Indicator EN 5 MONTH Indicator DAY Indicator Listening to radio Press the ON OFF button 11 to return the unit on Use the Tune or Tune button to select the desired radio station If you press and hold the Tune or Tune button for one second then release the unit will automatically scan to the next broadcasting station Press the ON OFF button 11 to turn the radio OFF To set recall the radio presets Press the ON OFF button 11 to turn the unit ON Use the Tune or Tune button to select the desired radio station Press the Memory Memory button P02 will blink in the display Press the Memory Memory button again to set the preset Repeat steps 2 through 4 to set more presets The unit can present 10 stations totally for FM When P01 P10 is blinking press the Tune or Tune button to select the present number Poznamka Ensure that the FM antenna is completely unrolled and extended for best FM reception Sleep operation When listening to radio press Snooze Sleep Dimmer button 6 to enter sleep mode You can adjust the sleep timer from 90 mins to 15 mins by pressing the Snooze Sleep Dimmer button 6 The unit will automatically turn off after the selected time EN 6 NAP time function count down timer During radio off mode press MEMORY SET MEMORY NAP button 4 to turn on NAP mode The NAP ti
8. tton 12 to adjust data forward e Keep depress lt lt or gt gt button for 2 seconds to enable auto forward Alarm wake up light The light will come on 5 minutes before the set alarm time The light will start out at a low level and increase gradually to the set max level ALARM DURATION amp SNOOZE FUNCTION Alarm duration Beep alarm or radio alarm will continue output for 30 minutes if no key press then it will stop automatically and wait for same alarm time on next day Action for Snooze During alarming press Snooze button 6 will enable snooze function Beep alarm or Radio alarm will stop Snooze interval is 9 minute not include second offset Snooze will continue unless press ON OFF button 11 to alarm off of buzzer alarm or Radio Alarm stop automatically after 30 minutes Display light ON OFF function Press Memory Set memory Display light auto ON OFF NAP button 4 for 3 seconds the LED display Indicator will light on the LED display will turn off after 15 seconds automatically Press any button to maintain the LED display for 15 seconds Press Memory Set Memory Display light auto ON OFF NAP button 4 for 3 seconds the LED display indicator will light off to cancel this function AUTO CHANGE DISPLAY CONTENT In radio off mode press VOLUME UP DISPLAY AUTO CHANGE ON OFF button 14 and keep depress over 2 seconds to enter time display auto change mode To display the Year and press again to dis
Download Pdf Manuals
Related Search