Tannoy Revolution XT 6F
Contents
1. D incl plinth Net weight Finish 08 REVOLUTION XT MANUAL REVOLUTION XT 6 25 120 60 240 89 dB 8 46 Hz 32 kHz 25 mm 1 Linear PEI dome with Torus Ogive WaveGuide and Omnimagnet technology 150 mm 6 multi fibre paper 44 mm 1 75 voice coil 1 8 kHz Passive low loss 2 order low pass 18 order high pass Downward ported reflex 10 8 0 38 cu ft 400 5 x 221 x 302 mm 15 8 x 8 7 x 11 9 7 5 kg 16 4 Ibs Dark Walnut Medium Oak REVOLUTION XT 6F 25 150 75 300 90 dB 8 38 Hz 32 kHz 25 mm 1 Linear PEI dome with Torus Ogive WaveGuide and Omnimagnet technology 150 mm 6 multi fibre paper 44 mm 1 75 voice coil 150 mm 6 multi fibre paper pulp cone with rubber surround 44 mm 1 75 edge wound voice coil 250 Hz amp 1 8 kHz Passive low loss 2 order low pass 1 order high pass Downward ported twin cavity coupled reflex 30 7 1 08 cu ft 1005 x 269 x 317 mm 39 6 x 10 6 x 12 5 16 3 kg 35 9 Ibs Dark Walnut Medium Oak REVOLUTION XT 8F 25 200 100 400 91 8 34 2 32 2 25 mm 1 Linear PEI dome with Torus Ogive WaveGuide and Omnimagnet technology 200 mm 8 multi fibre paper 44 mm 1 75 voice coil 200 mm 8 multi fibre paper pulp cone with rubber surround 44 mm 1 75 edge wound voice coil 250 Hz amp 1 8 kHz Passive low loss 2 order low pass t order high p2. be realised CABLE CHOICE Always use the best quality of cable available within your budget High quality audio signals passing from the amplifier to the loudspeaker are unusual in their demands on the cable Wide dynamic range and frequency bandwidth information has to coexist with the ability to transmit peak currents of at least 10 amps without incurring any loss or signal impairment This explains why the sound quality of the information reproduced by the loudspeakers is so dependent on the physical properties of the cables connecting them to the amplifier We would recommend that you always keep the cable runs as short as possible and the same length for each speaker Remember that cable construction can affect the sound quality so be prepared to experiment to find a cable that suits your ear and audio system UNPACKING To unpack the loudspeakers from their boxes remove tape from the top then fold the flaps right back before inverting the carton and contents Lift the carton clear of the contents then remove all inner packaging It is strongly recommended that you store all the packaging to allow protected transportation in future See Fig 1 FLOOR STANDING MODELS Revolution XT floor standing models perform best with carpet piercing spikes fitted These are supplied along with lock nuts and should be inserted into the threaded holes in the base of the cabinet Level the speaker and then tighten the lock nuts firmly but without using undue
3. force Spike locating cups are provided in the accessory pack and these may be used to protect sensitive floor surfaces Warning Ensure that the spikes are levelled and that the lock nuts are tightened firmly The spikes should be pushed through the carpet to locate into the flooring surface by applying pressure to the top of the cabinet If using on a sensitive floor surface place the protective cups under the levelled spikes Failure to do so could render the speaker unsteady and result in damage or injury should it be knocked over STAND MOUNTING MODELS Stand mounting or bookshelf speakers should be located securely on stands or a shelf in an appropriate position to place the Dual Concentric driver high frequency unit roughly at ear height when seated in the chosen listening position Positioning recommendations for stand mounted speakers can be found under the section entitled Positioning and fine tuning The Revolution XT Mini may also be wall mounted with a suitable bracket using two inserts on the rear of the loudspeaker with standard 60mm spacing The thread in the inserts is M5 It is the responsibility of the customer to ensure the chosen bracket is used within its load rating and the bracket is securely mounted to the wall with suitable hardware 04_ REVOLUTION XT MANUAL INSTALLATION To avoid potential damage to your loudspeaker ensure that the amplifier is switched OFF prior to connecting or disconnecting any cables Before
4. response well beyond that of conventional loudspeakers In addition the extension of the frequency response by fully two octaves corrects time and phase response within the bandwidth of normal human hearing Taking these acoustical phase anomalies beyond the audible range adds realism to the soundstage through improvements in imaging and the placement of sounds REVOLUTION XT MANUAL_03 TANNOY AMPLIFIER CHOICE Consult the product specification as this clearly shows the acceptable power range for amplifier matching to your speakers The high peak power handling of Tannoy loudspeakers permits responsible use with more powerful amplifiers please read the Warranty As with all loudspeaker systems the power handling is a function of voice coil thermal capacity Care should be taken to avoid overdriving any amplifier as this will cause output overload resulting in clipping or distortion within the output signal This if done for any extended period will cause damage to the speakers Generally an amplifier of higher power that is running hard but free of distortion will do less damage to the loudspeaker than a lower power amplifier continually clipping Remember also that a high powered amplifier running at less than 90 of output power generally sounds a great deal better than a lower powered example struggling to achieve 100 An amplifier with insufficient drive capability will not allow the full performance of the loudspeakers to
5. L LX REVOLUTION XT MANUAL_015 Tannoy Limited product designed in the United Kingdom Tannoy adopts a policy of continuous improvement and product specification is subject to change All other trademarks remain the property of their respective owners tannoy com 6481 0673 280115
6. TANNOY Revolution XT OWNER S MANUAL Revolution XT CONTENTS INTRODUCTION 03 POSITIONING AND FINE TUNING 06 DRIVER TECHNOLOGY 03 GRILLES 06 AMPLIFIER CHOICE 04 CARE OF CABINET 06 CABLE CHOICE 04 REVOLUTION XT HOME THEATRE 5 1 07 UNPACKING 04 THE SYSTEM 07 FLOOR STANDING MODELS 04 FRONT SPEAKERS 07 STAND MOUNTING MODELS 04 CENTRE CHANNEL SPEAKER 07 INSTALLATION 05 REAR EFFECTS SPEAKERS 07 CONNECTION IN SINGLE WIRE MODE 05 SUBWOOFER 07 CONNECTION IN BI WIRE MODE 05 TECHNICAL SPECIFICATIONS 08 09 BI AMPING 06 SET UP DIAGRAMS 010 012 WARRANTY No maintenance of the Revolution XT loudspeaker is necessary Please register your Tannoy product online at www tannoy com All of our products have been produced and tested with care and precision to give first class service All passive components are guaranteed for a period of 5 years from the date of purchase from an authorised Tannoy dealer subject to the absence or evidence of misuse overload or accidental damage All active and electronic components are guaranteed for a period of 2 years from the date of purchase from an authorised Tannoy dealer subject to the absence of or evidence of misuse overload or accidental damage If at any time during this warranty period the equipment proves to be defective for any reason other than accident misuse neglect unauthorised modification or fair wear and tear we will repair any such manufacturing defect or at our optio
7. ass Downward ported twin cavity coupled reflex 48 8 1 72 cu ft 1080 x 317 x 345 mm 42 5 x 12 5 x 18 6 19 9 kg 43 9 Ibs Dark Walnut Medium Oak TECHNICAL SPECIFICATIONS PERFORMANCE Recommended amplifier power watt RMS Continuous power handling watt RMS Peak power handling watt Sensitivity 2 83 volt O 1 m Nominal Impedance ohm Frequency response 6 dB DRIVE UNITS Dual Concentric high frequency Dual Concentric low frequency Bass driver CROSSOVER Crossover frequency Crossover type CONSTRUCTION Enclosure type Volume Dimensions H x W x D incl plinth Net weight Finish REVOLUTION XT Mini 25 100 50 200 88 dB 8 68 Hz 52 kHz 20 mm 0 79 Linear PEI dome with Torus Ogive WaveGuide and Omnimagnet technology 100 mm 4 multi fibre paper 35 mm 1 38 voice coil 2 8 kHz Passive low loss 2 order low pass t order high pass Rear ported reflex 8 4 1 0 12 cu ft 272 2 x 152 x 199 3 mm 10 7 x 6 0 x 7 8 3 7 kg 8 1 Ibs Dark Walnut Medium Oak REVOLUTION XT C 25 120 60 240 89 dB 8 62 Hz 52 kHz 20 mm 0 79 Linear PEI dome with Torus Ogive WaveGuide and Omnimagnet technology 100 mm 4 multi fibre paper 35 mm 1 38 voice coil 2x 100 mm 4 multi fibre paper pulp cone with rubber surround 35 mm 1 38 edge wound voice coil 2 8 kHz Passive low loss 2 order low pass 1 order high pas
8. at the rear usually wall mounted and a centre channel The subwoofer provides the 1 part of the system In home Theatre applications the matched dispersion of all Revolution XT models provides a very focussed soundstage retaining natural voicing and ensuring that aural effects and speech localisation pan from left to right and front to rear seamlessly WARNING STRONG MAGNETIC FIELDS The powerful magnet system in Revolution XT models will cause picture distortion with conventional CRT televisions and monitors and should not be used in close proximity There are no issues with plasma LCD or LED televisions or monitors FRONT SPEAKERS The ultra wide dynamic range and power handling capability of Revolution XT loudspeakers will provide a stunning home cinema experience The speakers should be positioned on either side of the TV or projection screen and then placed in line with the screen surface CENTRE CHANNEL SPEAKER In all cases the centre channel speaker should be positioned as near to the TV screen as possible The viewing position when seated determines the ideal mounting height but in all cases this should be as close as possible to ear height As with the main speakers the front baffle panel should be as near as possible in line with the screen surface The Revolution XT C can be wired in single wire bi wire or bi amp modes Please refer to figs 2 3 amp 4 for connection guidance bearing in mind that connection should be mad
9. e to the dedicated centre channel output on your A V processor amplifier s REAR EFFECTS SPEAKERS The integrity of the special effects soundstage created by the source material will be compromised if the speakers are installed on the sidewalls for that reason they should always be placed behind the main viewing position Placement should mirror as near as possible the location of the front pair and 0 5 metres 20 from the rear wall SUBWOOFER As the subwoofer only produces low frequency therefore monaural information it is difficult to detect its location by ear It could as a result be situated anywhere in the room but optimum performance will be gained by locating the subwoofer between the main stereo pair of speakers Bass output will increase when placed next to a wall or in a corner so use the subwoofer volume control to balance the output with the rest of the system Please refer to the manual supplied with the subwoofer for advice on installation and set up REVOLUTION XT MANUAL 07 TANNOY TECHNICAL SPECIFICATIONS PERFORMANCE Recommended amplifier power watt RMS Continuous power handling watt RMS Peak power handling watt Sensitivity 2 83 volt 1 m Nominal impedance ohm Frequency response 6 dB DRIVE UNITS Dual Concentric high frequency Dual Concentric low frequency Bass driver CROSSOVER Crossover frequency Crossover type CONSTRUCTION Enclosure type Volume Dimensions H x W x
10. ity the enthusiast will appreciate the slight improvement in clarity and detail that is achieved by removing the grilles during listening It is held in place by concealed magnets to promote a neat visual appearance when removed CARE OF CABINET The cabinets should only be cleaned with a dry cloth or with a light application of quality non silicone furniture polish 06_ REVOLUTION XT MANUAL REVOLUTION XT HOME THEATRE 5 1 GENERAL INFORMATION Unlike other forms of encoded surround audio 5 1 offers full bandwidth capability for the surround and centre channels with the ability to treat the subwoofer as a single discreet channel for special effects playback or for music applications as a dedicated low frequency instrument channel This places new demands on the surround and centre channel loudspeakers in both the mixing environment and the playback environment The 5 1 format allows the mix engineer in the recording studio to assign audio information to one or more discreet channels of playback providing very vivid and exacting localisation for the apparent sound sources in the listening environment To reliably recreate that accurate localisation during playback the selection and location of loudspeakers becomes the single most critical issue next to the talent of the mix engineer in the studio See Fig 6 LX THE SYSTEM A fully operational 5 1 system consists of two main front loudspeakers two rear effects speakers
11. n replace it without charge for labour parts or return carriage If you suspect a problem with a Tannoy product in the first instance discuss it with your Tannoy dealer If you require further assistance then we ask that you deal directly with your local Tannoy distributor If you cannot locate your distributor please contact Tannoy Customer Services at the address given below Customer Services Tannoy Ltd Rosehall Industrial Estate Coatbridge Strathclyde ML5 4TF Scotland Telephone 44 1236 420199 Fax 44 1236 428230 E mail enquiries tannoy com DO NOT SHIP ANY PRODUCT TO TANNOY WITHOUT PREVIOUS AUTHORISATION Our policy commits us to incorporating improvements to our products through continuous research and development Please confirm current specifications for critical applications with your supplier 02_ REVOLUTION XT MANUAL INTRODUCTION Thank you for selecting Tannoy loudspeakers developed in the UK by our dedicated team of design engineers They are the choice of discriminating music lovers the world over Musical excellence is designed into our loudspeakers from the start Careful selection of the very best components combined with strict quality control procedures in the production process ensures this level of excellence is maintained To gain maximum performance from your loudspeakers please take time to read this owner s manual in full before installation Once you have set up your new loudspeakers please register
12. n ensure that playback performance in the home for two channel stereo or multi channel home cinema is strictly controlled to accurately reflect the sound engineer s artistry In nature all sounds emanate from a single point in space The high frequency unit of the Dual Concentric centrally mounted in the throat of the main mid bass driver is so positioned as to acoustically replicate this single point source delivering an exceptionally natural sound with an incredibly wide imaging sweet spot which is further enhanced by the newly developed Torus Ogive Waveguide creating an expansive soundstage with remarkably focused placement of images Wideband Technology Tannoy has incorporated its own WideBand technology into the design of these drivers Not only does this exceptional in house technology resolve fine detail of high frequency information but it also effectively enhances the listening experience throughout the whole frequency range The WideBand high frequency system creates an increased immediacy airiness and impact making music and movie sound more natural and true to life Sounds contain transient information and rich harmonics beyond the range of human hearing for pure tones Even low frequencies have leading edge transients reaching 30 kHz Tannoy WideBand high frequency units will accurately reproduce the leading edge of individual sounds allowing the listener to experience the entire bandwidth by extending the frequency
13. r In this connection option separate power amplifiers are used for bass and treble signals in each loudspeaker Four mono or two stereo amplifiers of the same type are required for a stereo pair of loudspeakers Ensure that the link plates between the loudspeaker terminals are removed and that correct polarity is maintained throughout If two stereo amplifiers are used it is recommended that one amplifier supply bass information to left and right loudspeakers and the other the treble information See Fig 4 POSITIONING AND FINE TUNING To get best results from your new Tannoy Revolution XT loudspeakers it is worthwhile spending a little time finding the optimum setup configuration Begin by angling the speakers towards your chosen listening position usually this is on the centre line of the room so that when seated you can just see the inner side panel of each speaker The front of the loudspeaker should not be obstructed in any way The loudspeakers should be located between 1 5 to 4 5 metres 5 ft to 15 ft apart with the listening position set slightly further away than the speakers are apart Avoid positioning the loudspeakers in corners of the room as this will have a negative effect on performance Ideally maintain a distance of at least 0 5 metres 20 from the rear wall and 1 metre 39 from the side See Fig 5 GRILLES The Revolution XT grille has been designed to provide acoustic transparency However for ultimate fidel
14. s Rear ported reflex 7 61 0 27 cu ft 176 9 x 450 x 205 6 mm 7 0 x 17 7 x 8 2 7 9 kg 17 5 lbs Dark Walnut Medium Oak LX REVOLUTION XT MANUAL_09 SET UP DIAGRAMS Fig 1 Unpacking TANNOY 1 i PLANT T a LT Fig 2 Single Wire Mode TO RIGHT SPEAKER d m rm E L R POWER AMPLIFIER DUAL CONCENTRIC OMNIMAGNET SYSTEM O LINKS IN PLACE 010_ REVOLUTION XT MANUAL SET UP DIAGRAMS Fig 3 Bi Wire Mode Revolution XT AD GEN DUAL CONCENTRIC OMNIMAGNET SYSTEM O LINKS REMOVED Fig 4 Bi Amp Mode LINKS REMOVED TO RIGHT SPEAKER TO RIGHT SPEAKER R HIGH FREQUENCY POWER AMPLIFIER LOW FREQUENCY POWER AMPLIFIER L R E 1 TO RIGHT SPEAKER LX REVOLUTION XT MANUAL_011 TANNOY SET UP DIAGRAMS Fig 5 Recommended Positioning Stereo Pair 0 5 METRES OR MORE q EB ocd METRES eee ONE METRE OR MORE 11 E 9 Fig 6 Recommended Positioning Home Cinema 1 METRE OR MORE amp m REAR CENTRE 1 5 To 4 5 METRES e u REAR 0 5 METRES OR MORE 012 REVOLUTION XT MANUAL NOTES LX REVOLUTION XT MANUAL_013 TANNOY 014 REVOLUTION XT MANUA
15. switching on double check that all connections are secure and that polarity is correct CONNECTION IN SINGLE WIRE MODE For single wire mode leave the link plates between the LF and HF terminals in place See Fig 2 For optimum performance in single wire mode loudspeaker cable connections from the amplifier should be made to the high frequency HF terminals of the loudspeaker The positive plus terminal on the amplifier left channel marked or coloured red must be connected to the positive HF terminal on the left speaker The left speaker is the one on the left as you look at the stereo pair from your listening position The negative minus terminal on the amplifier left channel marked or coloured black must be connected to the negative HF terminal on the left speaker Repeat this connection process for the right speaker Remember that the positive or red on the amplifier must be connected to the positive or red on the speaker and the negative or black to negative Select a signal source such as a CD player switch on the amplifier and slowly turn up the volume control to check that both loudspeakers are reproducing bass and treble information CONNECTION IN BI WIRE MODE Please note in bi wire mode that the link plates must not be used See Fig 3 Be sure that the amplifier is switched OFF and then prepare the two sets of cabling for each side of the system separately Measure and cut four lengths of cable t
16. them on our website this does not limit your legal rights Loudspeakers are electromechanical devices that run in through use performance will therefore improve after an initial period of 24 hrs use Once they have been further run in over a longer period there will be clear enhancement of the stereo imaging mid band quality and bass performance characteristics LX We are confident that you will continue to enjoy your new Tannoy Revolution XT loudspeakers for many years to come DRIVER TECHNOLOGY The Tannoy Dual Concentric Tannoy Dual Concentric drivers have been incorporated into the Revolution XT loudspeakers Intensive research and development has produced an all new version of this proven technology that builds upon the legendary performance of this exclusive Tannoy driver design This new driver offers enhanced dispersion creating an even more uniform spread of sound around the listening environment At the same time the introduction of the Omnimagnet configuration allows the high frequency unit to be placed even closer to the acoustic centre of the low frequency unit further improving time alignment between the two drive units The time coherent point source and constant directivity nature of the dispersion characteristics inherent in the Dual Concentric makes it an accepted industry standard in studio monitoring By exceeding the rigorous demands of the recording and mastering environment Tannoy ca
17. wo per speaker Label two of the cable lengths Left LF and Left HF low frequency and high frequency then repeat this process for the right pair If your amplifier is not equipped with separate output terminals for bass and treble information then at the amplifier end of the cables twist the Left LF positive and the Left HF positive together Connect these to the amplifier Left channel positive terminal marked plus or coloured red Twist the Left LF negative and the HF negative cables together and connect them to the amplifier Left channel negative terminal marked minus or coloured black At the loudspeaker end connect the cables labelled Left LF and Left LF to the left hand loudspeaker LF terminals ensuring that you note the polarity markings on the cable sheathing Then proceed to connect the Left HF and Left HF to the HF terminals on the same loudspeaker Repeat this process to connect the right hand loudspeaker to the amplifier right channel output once again ensuring that polarity is correct throughout Switch the amplifier on with the volume control set at its lowest setting Select a favourite source and slowly turn up the volume to a low level Check that bass and treble information is being reproduced from both speakers if not switch OFF the amplifier and recheck the connections LX UONI OA REVOLUTION XT MANUAL_05 TANNOY BI AMPING Bi Amping extends the principle of bi wiring one stage furthe
Download Pdf Manuals
Related Search