Elo Touch Solution 1940L
Contents
1. Projected Capacitive Touch Technology When connected to Windows 7 computers the touchmonitor can report 2 simultaneous touches When connected to Windows XP computers the touchmonitor reports single touches No additional drivers are required for this touch technology to work it uses Windows HID drivers No calibration is required for this touch technology Gesture Support The IntelliTouch Plus and projected capacitive touchscreen technologies enable several gestures that support single and multiple contacts Refer to the Microsoft Website http msdn microsoft com en us library dd940543 on the various gestures that are supported in Windows 7 alt User Manual 1940L TOUCHSYSTEMS SW601787 RevA Page 15 of 26 connectivity Video A display s native resolution is its width and height measured in number of pixels Generally for best performance an image displayed on this monitor will look best when your computer s output resolution matches this monitor s native resolution of 1366x768 For computer output resolutions at non native resolutions the monitor will scale the video to its panel s native resolution This involves stretching or compressing the input image as needed in the X and Y dimensions to fit the display s native resolution An unavoidable byproduct of the scaling algorithms is a loss of fidelity when the computer s output video image is scaled by the monitor to fit the display This loss of fidelity is most appar2. User Manual Elo TouchSystems 1940L Touchmonitor TOUCH SOLUTIONS l User Manual 1940L gt TOUCHSYSTEMS SW601787 Rev A Page 1 of 26 comrectivity Copyright 2012 Tyco Electronics Corporation TE Connectivity Ltd Company All Rights Reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means including but not limited to electronic magnetic optical chemical manual or otherwise without prior written permission of Tyco Electronics Disclaimer The information in this document is subject to change without notice Tyco Electronics Corporation and its Affiliates in the TE Touch Solutions business unit in the TE Connectivity Ltd family of companies collectively TE makes no representations or warranties with respect to the contents herein and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose TE reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of TE to notify any person of such revisions or changes Trademark Acknowledgments Accu Touch Elo logo Elo TouchSystems IntelliTouch TE Connectivity and TE logo are trademarks of the TE Connectivity Ltd family of companies Windows is a trademark of the Microsoft group of companies Other product names mentio
3. Page 21 of 26 connectivity Chapter 7 Regulatory Information Electrical Safety Information Compliance is required with respect to the voltage frequency and current requirements indicated on the manufacturer s label Connection to a different power source than those specified herein will likely result in improper operation damage to the equipment or pose a fire hazard if the limitations are not followed There are no operator serviceable parts inside this equipment There are hazardous voltages generated by this equipment which constitute a safety hazard Service should be provided only by a qualified service technician Contact a qualified electrician or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power Il Emissions and Immunity Information Notice to Users in the United States This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications Notice to Users in Canada This equipment complies with the Class B limits for radio noise emissions from digital apparatus as established by the Radio Inter
4. 61 Tel 786 923 0251 Tel 800 557 1458 Fax 32 0 16 35 2101 Fax 81 45 478 2180 Fax 305 931 0124 Tel 650 361 4800 elosales elotouch com www tps co jp carlos valladares te com Fax 650 361 4722 customerservice elotouch com 2012 Tyco Electronics Corporation a TE Connectivity Ltd Company All rights reserved STE 22 User Manual 1940L p SOL LITIO AS TOUCHSYSTEMS SW601787 Rev A Page 26 of 26 connectivity
5. Connections 1 2 3 4 l gt User Manual 1940L gt Connect the DVI or VGA video cables between the monitor s DVI VGA input connectors and your DVI VGA video source respectively Tighten the video cable s screws with the best performance Connect the USB touch cable between the monitor s USB connector amp your PC s USB port Connect a 12VDC power supply to the monitor s input power jack The touchmonitor ships in an ON state video should be displayed on your monitor already TOUCH SOLUTIONS TOUCHSYSTEMS SW601787 RevA Page 5 of 26 connectivity Installing the Touch Technology Software Drivers Some software installation is required for your touchmonitor to work with your computer The drivers for the Windows 7 XP Vista WePOS and 32 bit Server 2003 and 2008 operating systems are provided with your touchmonitor on a CD Visit the Elo TouchSystems website www elotouch com for e The most up to date touch driver versions e Additional touch driver information e Detailed touch driver installation guides e Touch drivers for other operating systems Insert the Elo TouchTools CD into your computer s CD ROM drive The CD should automatically run the Elo TouchTools application Select Install Driver for This computer Elo TouchSystems TouchTools Rev AG Eg ae Install Driver For This Computer Creake Driver Install Package pe b ml Touchmonitor Peripherals Tyco Electronics l Install Acrob
6. YSTEMS SW601787 Rev A Page 19 of 26 connectivity Chapter 5 Technical Support If you are experiencing trouble with your touchmonitor refer to the following suggestions If the problem persists please contact your local dealer or contact Elo TouchSystems Customer Service Solutions to Common Problems turning on the system Verify the power supplies are functioning Use the OSD to increase the contrast If the Power Status LED is blinking the monitor or Monitor display is blank Computer Module may be in SLEEP mode Press any key move the mouse touch the Touchscreen to see if the image reappears Adjust your computer s resolution timing mode to be within the allowable timing ranges specified for your touchmonitor see website for specifications Verify your PC has the latest Elo drivers installed Touch functionality doesn t work Perform the calibration routine provided with the latest Elo drivers Monitor displays an Out Of Range message Technical Assistance Visit www elotouch com products for technical specifications for this device Visit www elotouch com go websupport for online self help Visit www elotouch com go contactsupport for technical support See this user manual s last page for worldwide technical support phone numbers I 2 TE TOUCH User Manual 1940L E SOLUTIONS TOUCHSYSTEMS SW601787 Rev A Page 20 of 26 comnectivity Chapter 6 Safety amp Maintenance Safety To avoi
7. at Reader view Touchmonitor User Guides View Catalog Browse CD http ans elokouch com TOUCH SOLUTIONS gt TE User Manual 1940L TOUCHSYSTEMS SW601787 RevA Page 6 of 26 connectivity For Windows XP Vista Server 2003 Server 2008 and WEPOS installations install the USB Touchscreen Drivers when prompted Elo Touchscreen Setup 5 7 0 43 Welcome to Elo Touchscreen Setup TOUGHSYSTEMS Install Serial Touchscreen Drivers Install APR Touchscreen Driver lt Back Mext gt Cancel For Windows 7 installations check the Install driver box under Elo USB Interfaces Other Touchscreens TETouchPlus Version 1 3 0 0 Lucas Install drivers for all detected Elo Touchscreens Tyco Electronics Cur commitment Your advantage Elo USB Interfaces APR Touchscreens 0 detected Other Touchscreens 1 detected C Install driver Install driver Seral RS 232 Interfaces 0 detected USB Serial Port COM3 USB Seral Port COM4 Install driver on selected port s Align touchscreens at end of installation Re detect Touchscreens Install After accepting the end user license agreement the drivers will finish installing Reboot your computer after the install is complete p i User Manual 1940L TOUCHSYSTEMS SW601787 Rev A Page 7 of 26 connectivity TOUCH SOLUTIONS Installing the Touch Driver Intellifouch Plus Touchscreen Techno
8. d risk of electric shock follow all safety notices and do not disassemble the touchmonitor They are not user serviceable The slots located on the sides and top of the touchmonitor case are for ventilation Do not block or insert anything inside the ventilation slots Ensure that your installation is equipped to maintain the specified environmental conditions listed in the Technical Specifications chapter Care and Handling The following tips will help keep your touchmonitor functioning at an optimal level e Disconnect the AC power cable before cleaning e To clean the display unit cabinet use a clean cloth lightly dampened with a mild detergent elt is important that your unit remains dry Do not get liquids on or inside the unit If liquid does get inside have a qualified service technician check it before you power it on again eDo not wipe the screen with a cloth or sponge that could scratch the surface e To clean the Touchscreen use window or glass cleaner applied to a clean cloth or sponge Never apply the cleaner directly to the touchscreen Do not use alcohol methyl ethyl or isopropyl thinner benzene or other abrasive cleaners Electrical amp Electronic Equipment Directive WEEE This product should not be disposed of with household waste It should be deposited at a facility that enables recovery and recycling TOUCH SOLUTIONS l gt User Manual 1940L gt TOUCHSYSTEMS SW601787 Rev A
9. ent when viewing feature rich images at close distances for example images containing small font text Your touchmonitor will likely not require video adjustments However for analog VGA video variations in video graphic card outputs may require user adjustments through the OSD to optimize the quality of the touchmonitor s displayed image These adjustments are remembered by the touchmonitor Also to reduce the need for adjustments for different video mode timings the monitor correctly scales and displays some of the video industry s most common video timing modes Refer to the technical specifications for this monitor at http www elotouch com for a list of these Preset Video Modes I DB TE FT LI T POUCA User Manual 1940L i E SOLUTIONS TOUCHSYSTEMS SW601787 Rev A Page 16 of 26 connectivity On Screen Display OSD Five OSD buttons are located on REMOTE OSD controller These can be used to adjust various display parameters I MENU lt gt smeT GO N Raabe gt The buttons and their functionality are Button Function when OSD is not displayed Function when OSD is displayed Menu Display OSD main menu Return to previous OSD menu Display OSD Brightness submenu Increase value of selected parameter select previous menu item Decrease value of selected parameter Display OSD Contrast submenu NG Select parameter for adjustment Select Display Video Source submenu EN Power on off Power on of
10. f Using the OSD buttons controls an on screen graphical user interface which displays on top of your input video allowing intuitive adjustment of the following display parameters Available Adjustment Default maximum Default best gray shade performance Only applicable for VGA input video Only applicable for VGA input video Default centered Only applicable for VGA input video postion Moves the image vertically on the display in single pixel increments V position Default centered Only applicable for VGA input video Automatically adjusts the system clock to the input analog VGA video signal affecting the Auto Adust Moston V position Clock and Phase menu items Only applicable for VGA input video Heston Dea the image horizontally on the display in single pixel increments TOUCH User Manual 1940L Er ae TOUCHSYSTEMS SW601787 RevA Page 17 of 26 connectivity the display s Y resolution and scales the X dimension to maintain the input video s aspect ratio and fills the rest of the display with equal black bars on the left and right Adjusts sharpness of the displayed images Default no sharpness adjustment Only applicable at non native input video resolutions Switches the scaling method between Full Scaling and Maintain Aspect Ratio Default Full Scaling Full Scaling scales the X and Y dimensions of the input video up or down as needed to the Aspect Ratio jdisplay s native resolutio
11. ference Regulations of Industrial Canada Notice to Users in the European Union Use only the provided power cords and interconnecting cabling provided with the equipment Substitution of provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards This Information Technology Equipment ITE is required to have a CE Mark on the Manufacturer s label which means that the equipment has been tested to the following Directives and Standards This equipment has been tested to the requirements for the CE Mark as required by EMC Directive 2004 108 EC as indicated in European Standard EN 55022 Class B and the Low Voltage Directive 2006 95 EC as indicated in European Standard EN 60950 General Information to all Users This equipment generates uses and can radiate radio frequency energy If not installed and used according to this manual the equipment may cause interference with radio and television communications There is however no guarantee that interference will not occur in any particular installation due to site specific factors 1 In order to meet emission and immunity requirements the user must observe the following a Use only the provided I O cables to connect this digital device with any computer b To ensure compliance use only the provided manufacturer s approved line cord c The user is cautioned that changes or modifications to the equipment not ex
12. h touchmonitor is factory calibrated and should not need manual calibration unless the input video is not fully scaled to the native resolution or the touch experience needs to be calibrated to a specific user IntelliTouch Plus Touchscreen Technology When connected to Windows 7 computers the touchmonitor can report 2 simultaneous touches When connected to Windows XP computers the touchmonitor reports single touches The IntelliTouch Plus touchscreen can be re calibrated to your displayed video image if needed through the Calibration function in the Elo driver control panel The IntelliTouch Plus driver will only support multiple monitor if they are all using the IntelliTouch Plus touch technology To use multiple IntelliTouch Plus monitors double click on the EloConfig desktop shortcut to open up the Elo Touchscreen Configuration screen T POUCA User Manual 1940L SOLUTIONS TOUCHSYSTEMS SW601787 RevA Page 14 of 26 commectivity to calibrate multiple monitors Copyrights Component versions Build info Restart Elo touch device service Restart Tablet Input Service Match touch input to a display for English OS with multiple monitors r Align all touchmonitors Device info Edge acceleration Disable touch Restore default calibration Apply to all monitors Hide cursor during calibration increase size of Windows title bars Elo suppor info Download driver packages for different platforms
13. logy Multi touch Support USB Single monitor Windows 7 ONLY Follow the directions on the screen to complete the driver setup for your Windows 7 system Insert the Elo CD ROM in your computer s CD ROM drive EloSetup launches 1 2 3 Click Install Driver for This Computer 4 Click Install drivers for all other Elo USB interfaces 5 E ten Electronics Cur Commitment Your advantage Elo USB Interfaces APR Touchscreens 1 detected fr Other Touchscreens 1 detected Install driver VI Install driver USB Serial Pot COM3 USB Serial Pot COM Install driver on selected portis Align touchscreens at end of installation Re detect Touchscreens TOUCH SOLUTIONS User Manual 1940L gt TOUCHSYSTEMS SW601787 Rev A Page 8 of 26 connectivity TOUCHSYSTEMS Elolnst Tyco Elect 6 Review and accept the license agreement error Please read the following license agreement carefully Press the PAGE DOWN key to see the rest of the agreement You must agree with the license for the setup to proceed BY DOWNLOADING AND OR INSTALLING AND OR USING THE SOFTWARE YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT INCLUDING THIS SOFTWARE PRODUCT LICENSE AND LIMITED WARRANTY IMPORTANT READ CAREFULLY This Elo TouchSystems End User License Agreement EULA is a legal agreement between you either an individual or a single entity and Elo TouchSystems a business
14. mal operating conditions listed below so that the use of this electronic information product will not result in any severe environmental pollution any bodily injury or damage to any assets Operating Temperature 0 40 Humidity 20 80 non condensing Storage Temperature 20 60 Humidity 10 90 non condensing mD 2 It is encouraged and recommended that this product be recycled and reused according to local laws The product should not be thrown away casually EDEN V Power Adapter Specifications Electrical Ratings Input 100 240VAG 50 60Hz Output 12VDC minimum 4 16A LPS VI Monitor Specifications Electrical Ratings Input 12VDC 2 1 A Operating Conditions Temperature 0 C 40 C Humidity 20 to 80 non condensing Altitude 0 to 3 048m Storage Conditions Temperature 20 C 60 C Humidity 10 to 90 non condensing Altitude 0 to 12 192m I DB TE FT LI T POUCA User Manual 1940L i E SOLUTIONS TOUCHSYSTEMS SW601787 Rev A Page 24 of 26 connectivity Chapter 8 Warranty Information Except as otherwise stated herein or in an order acknowledgment delivered to Buyer Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship The warranty for the TouchMonitors and their components is 3 three years Seller makes no warranty regarding the model life of components Seller s suppliers may at any time and from time to time make changes in the compone
15. n Fill To Aspect Ratio Assuming a landscape orientation and an input video with aspect ratio smaller than 1920x1080 scales the Y dimension of the input video up or down as needed to Selects the display s color temperature The available color temperatures are 9300K 7500K 6500K 5500K and User Defined If the User Defined option is selected the user can change the color temperature by changing individual R G and B gains on a scale from 0 to 100 Default User Defined with R G and B all set to 100 Adjusts how long a period of OSD button inactivity the touchmonitor will wait before closing the SD Timeout OSD The adjustable range is between 5 and 60 seconds Default 15 seconds O OSD Rotation Adjusts the OSD menu to Portrait or Landscape mode by 90 degrees clockwise O Japanese Default English H Position Default centered V Position Default centered Selects which orientation the OSD text is displayed in The available options are 0 degrees OSD Rotation landscape and 90 degrees portrait Default 0 degrees landscape Selects which language the OSD information is displayed in The available languages are S English French Italian German Spanish Simplified Chinese Traditional Chinese and Language Displays the following information 1940L TouchMonitor Monitor part number Monitor serial number Current video input source Current video resolution V sync frequency ww
16. ned herein may be trademarks or registered trademarks of their respective companies Tyco Electronics claims no interest in trademarks other than its own I DB TE FT LI T POUCA User Manual 1940L i E SOLUTIONS TOUCHSYSTEMS SW601787 Rev A Page 2 of 26 connectivity Table of Contents Chapter 1 Introduction rrorrrnrrrnrernrernrernrrrnrerrern vers rvernvernvennvernrennnen 4 Chapter 2 Installation srrorrrorrrnrornrernrernrernrornvorrvrernrernrernvernrernnen 5 Chapter 3 Mounting rnrrvrrrrrnrernrernrernrernrernvernvernvvrrnvernvernvernvernvernnen 11 Chapter 4 OPPGA posene dess 14 Chapter 5 Technical Support rorrrsrrrsrrrsvorsnrrrvrrrvrrrnrrrnrernvernrennnen 20 Chapter 6 Safety amp Maintenance ramrnrrrnrrsnrrnrornrervrrsvernrernnenner 21 Chapter 7 Regulatory Information 0 0 cece renee 22 Chapter 8 Warranty Information 0 0 cece eneete cence 25 gt ret POUCA User Manual 1940L SOLUTIONS TOUCHSYSTEMS SW601787 RevA Page 3 of 26 connectivity Chapter I Introduction Product Description Your new touchmonitor combines Elo TouchSystems reliable product performance with the latest developments in touch technology and display design This combination of features creates a natural flow of information between a user and the touchmonitor This widescreen touchmonitor incorporates a 24 bit color ac
17. nts delivered as Products or components Buyer shall notify Seller in writing promptly and in no case later than thirty days after discovery of the failure of any Product to conform to the warranty set forth above shall describe in commercially reasonable detail in such notice the symptoms associated with such failure and shall provide to Seller the opportunity to inspect such Products as installed if possible The notice must be received by Seller during the Warranty Period for such product unless otherwise directed in writing by the Seller Within thirty days after submitting such notice Buyer shall package the allegedly defective Product in its original shipping carton s or a functional equivalent and shall ship to Seller at Buyer s expense and risk Within a reasonable time after receipt of the allegedly defective Product and verification by Seller that the Product fails to meet the warranty set forth above Seller shall correct such failure by at Seller s options either i modifying or repairing the Product or ii replacing the Product Such modification repair or replacement and the return shipment of the Product with minimum insurance to Buyer shall be at Seller s expense Buyer shall bear the risk of loss or damage in transit and may insure the Product Buyer shall reimburse Seller for transportation cost incurred for Product returned but not found by Seller to be defective Modification or repair of Products may at Seller s
18. odes and standards Buyer retains and accepts full responsibility for all warranty and other claims relating to or arising from Buyer s products which include or incorporate Products or components manufactured or supplied by Seller Buyer is solely responsible for any and all representations and warranties regarding the Products made or authorized by Buyer Buyer will indemnify Seller and hold Seller harmless from any liability claims loss cost or expenses including reasonable attorney s fees attributable to Buyer s products or representations or warranties concerning same T POUCA User Manual 1940L SOLUTIONS TOUCHSYSTEMS SW601787 Rev A Page 25 of 26 commectivity Check out the Elo TouchSystems Website www elotouch com Get the latest e Product Information e Specifications e News on upcoming events e Press releases e Software drivers e TouchMonitor Newsletter Getting in Touch with us To find out more about the extensive range of Elo touch solutions visit our Website at www elotouch com or simply call the office nearest you North America Belgium Asian Pacific Latin America TE Touch Solutions Tyco Electronics Raychem bvba Sun Homada Bldg 2F TE Touch Solutions 301 Constitution Drive Diestsesteenweg 692 1 19 20 Shin Yokohama 20801 Biscayne Blvd Ste 403 Menlo Park CA 94025 B 3010 Kessel Lo Kanagawa 222 0033 Miami FL 33180 USA Belgium Japan USA Tel 800 ELO TOUCH Tel 32 0 16 35 2100 Tel 81 45 478 21
19. of Tyco Electronics Corporation for the software portion of this Elo TouchSystems touchscreen and controller or touchmonitor which indudes the accompanying computer software printed materials and any online or electronic documentation SOFTWARE By installing copying or otherwise using the SOFTWARE you agree to be bound by the terms of this EULA User must accept the terms of this agreement when prompted in order to complete download and or installation of the software Software Product License The SOFTWARE is protected by U S and international copyright laws and treaties as well as other intellectual property laws and treaties The SOFTWARE is licensed not sold 1 GRANT OF LICENSE This EULA grants you the following rights Software You may install and or use if SOFTWARE already installed one copy of the SOFTWARE on a single computer associated with a single Ela TouchSystems touchscreen and controller or touchmonitor TE User Manual 1940L gt SW601787 Rev A Page 9 of 26 commectivity TOUCH SOLUTIONS 7 The touch driver setup is complete setup is complete TOUCH SOLUTIONS User Manual 1940L gt TOUCHSYSTEMS SW601787 Rev A Page 10 of 26 connectivity Chapter 3 Mounting General Mounting Information The OSD text can be rotated through the OSD menu to better suit your mounting orientation Rear VESA Mount A four hole 75x75mm mounting pattern for M4 screws i
20. option take place either at Seller s facilities or at Buyer s premises If Seller is unable to modify repair or replace a Product to conform to the warranty set forth above then Seller shall at Seller s option either refund to Buyer or credit to Buyer s account the purchase price of the Product less depreciation calculated on a straight line basis over Seller s stated Warranty Period These remedies shall be the buyer s exclusive remedies for breach of warranty Except for the express warranty set forth above seller grants no other warranties express or implied by statute or otherwise regarding the products their fitness for any purpose their quality their merchantability their non infringement or otherwise No employee of Seller or any other party is authorized to make any warranty for the goods other than the warranty set forth herein Seller s liability under the warranty shall be limited to a refund of the purchase price of the product In no event shall Seller be liable for the cost of procurement or installation of substitute goods by Buyer or for any special consequential indirect or incidental damages Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless from all liability relating to i assessing the suitability for Buyer s intended use of the Products and of any system design or drawing and ii determining the compliance of Buyer s use of the Products with applicable laws regulations c
21. or Australia C Tick Canada CUL IC China CCC Europe CE Japan VCCI Korea KCC e Standby Mexico NOM CoC Taiwan BSMI United States FCC UL IV China ROHS In accordance to Chinese law Administration on the Control of Pollution Caused by Electronic Information Products the section below lists out the name and amount of the toxic and or hazardous materials that this product may contain Component Toxic or Hazardous Substances and Elements Toxic or Hazardous Substances and Elements Z gt Z ooo o o Lead Pb Mercury Hg Cadmium Cd Hexavalent Polybrominated Polybrominated Chromium _ Biphenyls Diphenyl i Ethers FE Plastic Parts e gp atl User Manual 1940L SOL TOUCHSYSTEMS SW601787 Rev A Page 23 of 26 connectivity O Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this component is below the limit requirement in SJ T 11363 2006 X Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this component Is above the limit requirement in SJ T11363 2006 For items marked with X exemptions were taken according to EU RoHS Explanation of Markings 1 In accordance with the SJ T11364 2006 requirement the electronic information products are marked with the following pollution control logo The Environment Friendly Use Period for this product is 10 years The product will not leak or mutate under nor
22. pressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 If this equipment appears to cause interference with radio or television reception or any other device a Verify as an emission source by turning the equipment off and on If you determine that this equipment is causing the interference try to correct the interference by using one or more of the following measures i Move the digital device away from the affected receiver ii Reposition turn the digital device with respect to the affected receiver T POUCA User Manual 1940L SOLUTIONS TOUCHSYSTEMS SW601787 Rev A Page 22 of 26 commectivity iii Reorient the affected receiver s antenna iv Plug the digital device into a different AC outlet so the digital device and the receiver are on different branch circuits v Disconnect and remove any I O cables that the digital device does not use Unterminated I O cables are a potential source of high RF emission levels vi Plug the digital device into only a grounded outlet receptacle Do not use AC adapter plugs Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user If you need additional help consult your dealer manufacturer or an experienced radio or television technician Ill Agency Certifications The following certifications and marks have been issued or declared for this monit
23. s provided on the rear of the monitor The VESA FDMI compliant counting is coded VESA MIS D 75 C VESA MOUNTING HOLES PER MIS D 75 75 THREAD MAX DEPTH 12MM Xx4 15 TOUCH SOLUTIONS on User Manual 1940L gt come cvify SW601787 RevA Page 11 of 26 TOUCHSYSTEMS 445 6 SCALE 1 0900 TOUCH SOLUTIONS a User Manual 1940L TOUCHSYSTEMS SW601787 RevA Page 12 of 26 connectivity Side Bracket Mount Threaded holes are provided on the sides of the monitor for mounting using the provided brackets TOUCH SOLUTIONS a E i User Manual 1940L TOUCHSYSTEMS SW601787 Rev A Page 13 of 26 connectivity Chapter 4 Operation Power To turn the touchmonitor on or off press the touchmonitor power button once The Power Status LED on the REMOTE OSD controller functions according to the following table TouchMonitor Computer Module status LED status OFF SLEEP PULSING The system consumes low power when in SLEEP and OFF modes For detailed power consumption specifications refer to technical specifications on the Elo website http www elotouch com Touching the screen will bring the attached host PC out of SLEEP mode similar to moving the mouse or pressing a keyboard key To improve reliability and reduce wasteful power consumption disconnect the AC power cable from the power adapter when long periods of disuse are planned Touch Your IntelliTouc
24. tive matrix thin film transistor LCD panel to provide high quality display performance Its HD resolution of 1366x768 is suitable for displaying graphics and images Its LED backlight significantly reduces power consumption and eliminates mercury compared to CCFL backlit panels Other features that enhance this LCD monitor s performance are Plug amp Play compatibility and on screen display OSD controls Precautions Follow all warnings precautions and maintenance as recommended in this user manual to maximize the life of your unit and prevent risks to user safety See the Safety amp Maintenance chapter for more information This manual contains information that is important for the proper setup and maintenance of the unit Before setting up and powering on your new touchmonitor read through this manual especially the Installation Mounting and Operation chapters TOUCH SOLUTIONS I User Manual 1940L gt TOUCHSYSTEMS SW601787 Rev A Page 4 of 26 connectivity Chapter 2 Installation Unpacking the Touchmonitor Open the carton and verify the following items are present e Touchmonitor with protective sheet for its face eElo TouchTools CD amp User Manuals CD e Quick Install Guide e Japanese language regulatory information pamphlet e DVI cable depending on model purchased eVGA cable eUSB cable e REMOTE OSD controller Connector Panel amp Interfaces USB TOUCH VGA IN Touchmonitor
25. w elotouch com www te com Recall Selecting Recall Defaults restores all factory default settings for OSD adjustable parameters Defaults except OSD Language and for Preset Video Mode timings The monitor continually scans for active video on the VGA and DVI connectors This adjustment selects which of those input ports should be given priority to be displayed Video Source The options are VGA Priority DVI Priority Default DVI Priority Not available on models with only VGA input a OULULLA User Manual 1940L gt SOLUTIONS TOUCHSYSTEMS SW601787 Rev A Page 18 of 26 connectivity All touchmonitor adjustments made through the OSD are automatically memorized as soon as they are entered This feature saves you from having to reset your choices every time the touchmonitor is unplugged or powered off and on If there is a power failure the touchmonitor settings will not default to the factory specifications OSD and Power Lockouts Press and hold the Menu and Up buttons for two seconds to enable disable the OSD Locking feature When the OSD Locking is enabled pressing any of the Menu Up Down or Select keys will have no effect on the system Press and hold the Menu and Down buttons for two seconds to enable disable the Power Locking feature When the Power Locking is enabled pressing the power switch will have no effect on the system T POUCA User Manual 1940L SOLUTIONS TOUCHS
Download Pdf Manuals
Related Search