Kramer Electronics VP-5R
Contents
1. Features front panel EQ control Has switches on the underside for ID Bit control Has a video bandwidth exceeding 440MHz ensuring transparency even when operating at the highest resolutions Has a transmission range of more than 300ft more than 100m over STP cabling Is mains fed and housed in a half width 19 enclosure Has Hs and Vs polarity switches on its underside Supports HD signals high definition resolutions 720p 10801 and 1080p and SD signals Figure 3 and Table 3 define the VP S5THD POWER 1 44 VGA UXGA Distributor CATS Transmitter CAT5 OUT OUTPUT 1 OUTPUT 2 Figure 3 VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter KRAMER SIMPLE CREATIVE TECHNOLOGY Defining the VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter Table 3 VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter Features Feature Function 1 POWER Switch Illuminated switch for turning the unit ON or OFF 2 EQ Trimmer Turn to adjust the video EQ equalization compensation 3 INPUT 15 pin HD Connector Connect to the VGA UXGA source 4 CAT 5 OUT RJ 45 Connector Connect to the LINE IN RJ 45 connector on the VP 5R 5 OUTPUT 15 pin HD Connector Connect to the VGA UXGA acceptor s from 1 to 4 6 Power Connector with Fuse Connect to the AC mains using the supplied power cable Figure 4 and Table 4 define the underside of the VP STHD 7 4 VGA UXGA Distributor CAT 5 Transmitter Figure 4 VP 5THD 12. Feature Function 1 V SYNC Switch Slide the switch to the right to change the V SYNC polarity slide the switch to the left to retain the polarity 2 HSYNC Switch Slide the switch to the right to change the H SYNC polarity slide the switch to the left to retain the polarity 7 Connecting the VP 200XLTHD You can use the VP 200XLTHD and for example the TP 120 to configure an XGA line to Twisted Pair transmitter and receiver system To connect the VP 200XLTHD to the TP 120 as the example in Figure 7 illustrates 1 On the VP 200XLTHD connect the Computer graphics XGA source for example a computer to the INPUT 15 pin HD connector XGA OUT 15 pin HD connector to the acceptor for example to a projector 2 On the TP 120 connect the XGA OUT 15 pin HD connector to the XGA acceptor for example a display 1 By default both switches are set to the left Connecting the VP 200XLTHD 3 Connect the LINE OUT RJ 45 connector on the VP 200XLTHD to the LINE IN RJ 45 connector on the TP 120 via STP cabling see Section 8 1 4 Connect the 12V DC power adapter to the power socket on the VP 200XLTHD and plug the adapter into the mains electricity socket 5 Connect the other 12V DC power adapter to the power socket on the TP 120 and plug the adapter into the mains electricity socket 6 On the VP 200XLTHD if required use a screwdriver to adjust the Video output signal level Cable compensation equalizatio
3. our UTP skew free cable Kramer BC XTP may be used Bear in mind though that we advise using STP cables where possible since the compliance to electromagnetic interference was tested using those cables Although Unshielded Twisted Pair UTP cable might be preferred for long range applications the UTP cable should be installed far away from electric cables motors and so on which are prone to create electrical interference However since the use of UTP cable might cause inconformity to electromagnetic standards Kramer does not commit to meeting the standard with UTP cable 3 3 Recommendations for Achieving the Best Performance To achieve the best performance e Use only good quality connection cables to avoid interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables e Avoid interference from neighboring electrical appliances that may adversely influence signal quality and position your Kramer product away from moisture excessive sunlight and dust No operator serviceable parts inside unit Use only the Kramer Electronics input power wall adapter that is provided with the unit Disconnect power and unplug unit from wall before installing or removing the device or servicing unit 1 Available from Kramer Electronics on our Web site at http www kramerelectronics com Defining the VP 200XLTHD XGA Line Amp CAT 5 Transmitter Defining the VP
4. outputs VP 5R Connect up to 5 video outputs Connect the VP 5THD to the VP 5R via the CAT 5 cable Computer Graphics Source Located up to 300ft gt 100 meters away from the Computer Graphics Source Step 2 Connect the power If required FOR THE VP STHD FOR THE VP 5R O Adjust the EQ and LEVEL O Adjust the input EQ and LEVEL O Set the ID Bit Control switches Adjust the output EQ O Set the Polarity switches O Set the Polarity switches Overview 3 1 3 2 Overview This user manual describes the following products e Kramer TOOLS VP 200XLTHD XGA Line Amp CAT 5 Transmitter which accepts one computer graphics input and distributes the signal to its 15 pin HD connector output as well as transmitting it over STP cabling CAT 5 or similar to its appropriate receiver see Section 4 e Kramer VP 5THD 4 VGA UXGA Distributor CAT 5 Transmitter which is a distributor for computer graphics signals accepting one input and distributing the signal to its identical 4 outputs as well as transmitting it over CAT 5 STP cable to its appropriate receiver see Section 5 e Kramer VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor which is a distributor for computer graphics signals receiving the computer graphics signal via CAT 5 STP cable and distributing the signal to 5 identical 15 pin HD outputs see Section 6 This section describes e The Power Connect feature see Section 3 1 e Using Shielded Twisted Pair Uns
5. 1 4 VGA UXGA Distributor CAT 5 Transmitter Features 9 Table 4 VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter Underside Features 9 Table 5 VP SR CAT 5 Receiver 1 5 VGA UXGA Distributor Features 10 Table 6 VP SR CAT 5 Receiver 1 5 VGA UXGA Distributor Underside Features 11 Table 7 TP Connector Pinout 15 Table 8 Technical Specifications of the VP 200XLTHD with 30m CAT 5 cable 15 Table 9 Technical Specifications of the VP STHD with 60m CAT 5 cable 16 Table 10 Technical Specifications of the VP 5R with 30m CAT 5 cable 16 Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentation and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Thank you for purchasing the Kramer VP 200XLTHD XGA Line Amp CAT 5 Transmitter VP S5THD 4 VGA UXGA Distributor CAT 5 Transmitter and or VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor which are ideal for e Presentation and multimedia applications e Long range graphics distribution for schools hospitals security and stores The package includes e One or more VP 200XLTHD and or VP 5THD and or VP 5R e Power cord e This use
6. 200XLTHD XGA Line Amp CAT 5 Transmitter The VP 200XLTHD is a high performance XGA line amp CAT 5 transmitter that accepts one computer graphics XGA input provides necessary buffering and isolation and distributes the signal to the 15 pin HD connector output as well as transmitting it over STP cable to its appropriate receiver In particular the VP 200XLTHD e Can also accept HD signals high definition resolutions 480p 576p 720p 1080i and 1080p e Has a transmission range of more than 300ft 100m over STP cabling e Has a video bandwidth exceeding 400MHZz ensuring transparency even when operating at the highest resolutions e Includes output level control and cable equalization control via two trimmers on the front panel of the unit Figure and Table define the VP 200XLTHD Oi LINEOUT 12VDC KRAMER TOOLS XGA Line Amp CATS Transmitter WVP 200x 7D Figure 1 VP 200XLTHD XGA Line Amp CAT 5 Transmitter KRAMER SIMPLE CREATIVE TECHNOLOGY Defining the VP 200XLTHD XGA Line Amp CAT 5 Transmitter Table 1 VP 200XLTHD XGA Line Amp CAT 5 Transmitter Features Feature Function 1 12VDC Connect to the 12V DC power adapter 2 LINE OUT RJ 45 Connector Connect to the LINE IN RJ 45 connector on the TP 120 or the VP 5R 3 XGA OUT 15 pin HD Connector Connect to the XGA acceptor 4 INPUT 15 pin HD Connector Connect to the XGA source 5 LEVEL trimmer Turn to adjust the o
7. 4 Enlarged View ID BIT CONTROL PIN 4 x VGA UXGA Distributor CAT 5 Transmitter Underside Table 4 VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter Underside Features Feature Function 1 ID BIT CONTROL PIN 11 Slide to the left to set to ON to the right to set to OFF 2 Switches PIN 4 Slide to the left to set to ON to the right to set to OFF 3 VS Switch Slide the switch to the right to change the VS polarity to negative polarity POLARITY slide the switch to the left to retain the polarity default 4 Switches HS Switch Slide the switch to the right to change the HS polarity to negative polarity slide the switch to the left to retain the polarity default 1 Insert a screwdriver into the hole and carefully rotate it to trim the level 2 Using an STP CAT 5 cable with RJ 45 connectors at both ends the pinout is defined in Table 7 and Figure 9 3 The default Enabling the notebook or laptop to output a VGA signal to an external VGA monitor 4 Downgoing syncs Defining the VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor Defining the VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor The VP SR is a high performance distributor for computer graphics signals receiving the computer graphics signal via STP CAT 5 cable and distributing the signal to five identical 15 pin HD outputs In particular the VP 5R e Features front panel line input level and EQ control as well as
8. 68B Orange White Blue White 7 Pair 1 wW Z cq 12 45 78 36 Figure 9 TP Connector Technical Specifications Table 8 lists the technical specifications of the VP 200XLTHD Table 8 Technical Specifications of the VP 200XLTHD with 30m CAT 5 cable INPUT 1 XGA on a 15 pin HD connector OUTPUTS 1 XGA on a 15 pin HD connector 1 RJ 45 connector MAX OUTPUT LEVEL 2 4Vpp XGA 1 5Vpp CAT 5 BANDWIDTH 3aB 405MHz XGA RESOLUTION Up to UXGA up to 1080p DIFF GAIN 0 03 XGA 3 3 CAT 5 DIFF PHASE 0 03Deg XGA 0 3Deg CAT 5 K FACTOR lt 0 02 XGA and CAT 5 S N RATIO 780B XGA 71dB CAT 5 CONTROLS XGA LEVEL 1 6dB to 1 9dB EQ 0 to 4dB 50MHz COUPLING DC XGA AC CAT 5 POWER SOURCE 12V DC 105mA DIMENSIONS 12cm x 7 5cm x 2 5cm 4 7 x 2 95 x 0 98 W D H WEIGHT 0 3kg 0 67Ib approx ACCESSORIES Power supply 1 Specifications are subject to change without notice 2 For the VP 200XLTHD to TP 120 SETUP 15 Technical Specifications Table 9 lists the technical specifications of the VP STHD Table 9 Technical Specifications of the VP STHD with 60m CAT 5 cable INPUT 1 XGA on a 15 pin HD connector OUTPUTS 4 XGA on 15 pin HD connectors 1 RJ 45 connector MAX OUTPUT LEVEL 1 7Vpp XGA 1 7Vpp CAT 5 BANDWIDTH 3aB 445MHz XGA 154MHz CA
9. Kramer Electronics Ltd USER MANUAL Models VP 200XLTHD XGA Line Amp CAT 5 Transmitter VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor Contents Contents 1 Introduction 1 2 Getting Started 1 2 1 Quick Start 2 3 Overview 4 3 1 About the Power Connect Feature 4 3 2 Shielded Twisted Pair Unshielded Twisted Pair 4 3 3 Recommendations for Achieving the Best Performance 5 4 Defining the VP 200XLTHD XGA Line Amp CAT 5 Transmitter 6 5 Defining the VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter 8 6 Defining the VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor 10 7 Connecting the VP 200XLTHD 11 8 Connecting the VP 5THD and the VP 5R 13 8 1 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors 15 9 Technical Specifications 15 Figures Figure 1 VP 200XLTHD XGA Line Amp CAT 5 Transmitter 6 Figure 2 VP 200XLTHD XGA Line Amp CAT 5 Transmitter Underside 7 Figure 3 VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter 8 Figure 4 VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter Underside 9 Figure 5 VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor 10 Figure 6 VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor Underside 11 Figure 7 Connecting the VP 200XLTHD 12 Figure 8 Connecting the VP S5THD and the VP 5R 14 Figure 9 TP Connector 15 Tables Table 1 VP 200XLTHD XGA Line Amp CAT 5 Transmitter Features 7 Table 2 VP 200XLTHD XGA Line Amp CAT 5 Transmitter Underside Features T Table 3 VP STHD
10. LPAY FORAND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removalor installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damage
11. T 5 RESOLUTION Up to UXGA up to 1080p DIFF GAIN 0 8 XGA 3 2 CAT 5 DIFF PHASE 0 08Deg XGA 0 06Deg CAT 5 K FACTOR 0 1 XGA lt 0 05 CAT 5 S N RATIO 76dB XGA 73dB CAT 5 CONTROLS LEVEL 7 4cB to 3 5dB CAT 5 EQ 0 to 37 8dB 50MHz CAT 5 COUPLING DC XGA AC CAT 5 POWER SOURCE 230 VAC 50 60 Hz 115VAC U S A 13VA DIMENSIONS 22cm x 18cm x 4 5cm 8 7 x 7 x 1 7 W D H half 19 1U WEIGHT 1 2kg 2 6 lbs approx ACCESSORIES Power cord Table 10 lists the technical specifications of the VP 5R Table 10 Technical Specifications of the VP 5R with 30m CAT 5 cable INPUT 1 RJ 45 connector OUTPUTS 5 XGA on 15 pin HD connectors MAX OUTPUT LEVEL 1 4Vpp BANDWIDTH 3cB 150MHz DIFF GAIN 3 4 DIFF PHASE 0 05Deg K FACTOR lt 0 05 S N RATIO 74dB CONTROLS LEVEL 8 2cB to 4 3dB LINE EQ 0 to 30dB OUT EQ 0 to 8 6dB COUPLING AC POWER SOURCE 230V AC 50 60 Hz 115V AC U S A 9 2VA DIMENSIONS 22cm x 18cm x 4 5cm 8 7 x 7 x 1 7 W D H half 19 1U WEIGHT 1 2kg 2 6 lbs approx ACCESSORIES Power cord 1 For the VP STHD to TP 120 SETUP 2 The HD resolutions apply to the HD version of the unit 3 For the VP 5R to WP 110 SETUP 16 KRAMER SIMPLE CREATIVE TECHNOLOGY LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in materi
12. al and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with 3 Damage deterioration or malfunction resulting from 1 Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removal or installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WIL
13. atest information on our products and a list of Kramer distributors visit www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution INN Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000635 REV 2
14. hielded Twisted Pair cable see Section 3 2 e Recommendations for achieving the best performance see Section 3 3 About the Power Connect Feature The Power Connect feature applies as long as the cable can carry power This feature is available when using STP cable and the distance does not exceed 50m on standard CAT 5 cable For longer distances heavy gauge cable should be used For units which are connected via RJ 45 connectors make sure that the shield of the STP cable is connected to the metal casing of the connectors on both ends of the cable For units which are connected via terminal block connectors the shield of the STP cable must be connected to a ground terminal on the units at both ends use the ground terminal of the power supply connection if necessary For a CAT 5 cable exceeding a distance of 50m separate power supplies should be connected to the transmitter and to the receiver simultaneously Shielded Twisted Pair Unshielded Twisted Pair We recommend that you use Shielded Twisted Pair STP cable There are different levels of STP cable available and we advise you to use the best quality STP cable that you can afford Our non skew free cable Kramer BC STP is intended for analog signals where skewing is not an issue For cases where there is 1 CAT 5 cable is still suitable for the video audio transmission but not for feeding the power at these distances KRAMER SIMPLE CREATIVE TECHNOLOGY Overview skewing
15. ied power cord to the VP 5R 6 On the VP 5THD if required Set the H SYNC and V SYNC switches on the underside Adjust the front panel cable compensation equalization level 7 On the VP S5R if required Adjust the front panel LINE INPUT signal level and or cable compensation equalization level and or OUTPUT compensation equalization level On the underside set the V SYNC and H SYNC switches 1 When not all the outputs are required connect only those that are required and leave the other output s unconnected 2 We recommend that you use only the power cord that is supplied with each specific unit 3 Not illustrated in Figure 8 4 By default both switches are set down for negative V Sync and H Sync polarity 5 Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level Connecting the VP STHD and the VP 5R aul dLS dLN 5u07 Computer Graphics Source Local Local Display 1 Display 4 i 5 Display 1 Figure 8 Connecting the VP 5THD and the VP 5R 14 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 8 1 9 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors Table 7 and Figure 9 define the TP CAT 5 pinout using a straight pin to pin cable with RJ 45 connectors When using STP cable connect solder the cable shield to the RJ 45 connector shield Table 7 TP Connector Pinout PIN Wire Color Pair1 4and5 Pair2 3 and 6 EIA TIA 5
16. n level 7 On the TP 120 if required Adjust the video output signal level and or cable compensation equalization level On the underside set the H SYNC and V SYNC switches SS lt IS Long UTRISTF line E Computer EW T a Graphics OMIS Source Projector Display Figure 7 Connecting the VP 200XLTHD 1 Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level 2 By default both switches are set down for normal V SYNC and H SYNC polarity 12 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VP STHD and the VP 5R 8 Connecting the VP 5THD and the VP 5R You can use the VP STHD 4 VGA UXGA Distributor CAT 5 Transmitter and the VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor to configure an XGA line to Twisted Pair transmitter and receiver system To connect the VP 5THD to the VP 5R as the example in Figure 8 illustrates 1 On the VP 5THD connect the computer graphics source for example a computer to the INPUT 15 pin HD connector and connect up to four acceptors for example local displays to the OUTPUT 15 pin HD connectors 1 to 4 2 On the VP 5R connect up to five acceptors for example displays to the OUTPUT 15 pin HD connectors to 5 3 Connect the CAT 5 OUT RJ 45 connector on the VP STHD to the CAT 5 LINE IN RJ 45 connector on the VP 5R via STP cabling see Section 8 1 4 Connect the supplied power cord to the VP 5THD Connect the suppl
17. output EQ control e Is mains fed e Is housed in a half width 19 enclosure Figure 5 and Table 5 define the VP 5R 009000 o0o00 95000 OUTPUT 4 OUTPUT 5 Figure 5 VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor Table 5 VP SR CAT 5 Receiver 1 5 VGA UXGA Distributor Features Feature Function 1 POWER Switch Illuminated switch for turning the unit ON or OFF 2 LINE INPUT LEVEL Trimmer Turn to adjust the video input level 3 LINE INPUT EQ Trimmer Turn to adjust the video input EQ equalization compensation 4 OUTPUT EQ Trimmer Turn to adjust the video output EQ equalization compensation 5 CAT 5LINE IN RJ 45 Connector Connect to the LINE OUT RJ 45 connector on the VP 5THD 6 OUTPUT 15 pin HD Connector Connect to the VGA UXGA acceptor s from 1 to 5 7 Power Connector with Fuse Connect to the AC mains using the supplied power cable 1 Insert a screwdriver into the hole and carefully rotate it to trim the level 2 Using an STP CAT 5 cable with RJ 45 connectors at both ends the pinout is defined in Table 7 and Figure 9 10 KRAMER SIMPLE CREATIVE TECHNOLOGY Connecting the VP 200XLTHD Figure 6 and Table 6 define the underside of the VP SR CAT 5 Receiver 1 5 VGA UXGA Distributor Figure 6 VP 5R CAT 5 Receiver 1 5 VGA UXGA Distributor Underside Table 6 VP SR CAT 5 Receiver 1 5 VGA UXGA Distributor Underside Features
18. r manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 We recommend that you use only the power cord supplied with this device 3 Download up to date Kramer user manuals from http www kramerelectronics com 4 The complete list of Kramer cables is available at http www kramerelectronics com 1 Getting Started 2 1 Quick Start This quick start chart summarizes the basic setup and operation steps Step 1 Connect the Units Quick Start VP 200xITHD Connect the VP 200XLTHD to the TP 120 via the CATS cable Computer Graphics Source Projector Step 2 Connect the power If required O Adjust the EQ and LEVEL O Set the Polarity switches 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Getting Started n Quick Start VP 5THD Step 1 Connect the Units r URAR VP STHD Connect the video input VP 5THD Connect up to 4 video
19. s whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and light industry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION B Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment gt Use the supplied DC power supply to feed power to the machine gt Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products 17 For the l
20. utput signal level 6 EQ trimmer Turn to adjust the video EQ equalization compensation 7 ONLED Lights when the VP 200XLTHD receives power Figure 2 and Table 2 define the VP 200XLTHD NORMAL NEGATIVE NORMAL NEGATIVE Figure 2 VP 200XLTHD XGA Line Amp CAT 5 Transmitter Underside Table 2 VP 200XLTHD XGA Line Amp CAT 5 Transmitter Underside Features Switch Function VS Switch Slide the switch downward to change the VS polarity to negative polarity slide the switch upward to retain the polarity default HS Switch Slide the switch downward to change the HS polarity to negative polarity slide the switch upward to retain the polarity default 1 Using an STP CAT 5 cable with RJ 45 connectors at both ends the pinout is defined in Table 7 and Figure 9 2 Refer to the separate user manual PT 110 PT 120 TP 120 WP 110 available at http www kramerelectronics com 3 Insert a screwdriver into the hole and carefully rotate it to trim the level 4 Downgoing syncs Defining the VP STHD 1 4 VGA UXGA Distributor CAT 5 Transmitter Defining the VP 5THD 1 4 VGA UXGA Distributor CAT 5 Transmitter The VP STHD is a high performance distributor for computer graphics signals accepting one input providing necessary buffering and isolation and distributing the signal to its four identical outputs as well as transmitting it over STP CAT 5 cable to an appropriate receiver In particular the VP STHD
Download Pdf Manuals
Related Search