Kramer Electronics RK-1UTB rack accessory
Contents
1. 5 4 3 Connect other devices to the power sockets on the front panel 4 Connect the rear side power socket to the mains power The RK 1UTB is ready for use Mounting Units that do not have Underside Screw Holes Some Kramer machines do not have screw holes on the underside which fit the holes on the RK 1UTB These machines for example the VP 5x1 are connected via the screw holes on the sides of the RK 1UTB To mount the VP 5xl on the RK 1UTB as illustrated in Figure 5 do the following 1 Unscrew the two M3x6 screws from the side panel of the unit which will be attached to the side panel of the RK 1UTB 2 Place the VP 5xl on the rack adjacent to the inner side panel of the RK 1UTB 3 Insert the two M3x6 screws through the holes on the side panel of the RK 1UTB that fit the holes on the side panel of the unit 4 Tighten the screws 1 P N 2535 000635 2 A hal f 19 unit Install the Kramer RK 1UTB Under the Table Enclosure Screws Figure 5 Mounting a half 19 unit via Screws on the RK 1UTB Side Panel 5 5 Connecting a Blank Panel to the RK 1UTB You can connect a blank panel to the RK 1UTB to cover any empty spaces as the example in Figure 6 illustrates BLANK PANEL P N 60 900013 Figure 6 RK 1UTB Rack Adapter Connecting a Blank Panel 1 Specified in section 6 8 KRAMER SIMPLE CREATIVE TECHNOLOGY Technical Specifications 6 Technical Specifications T2. consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for i Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and lightindustry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential commercial and lightindustry environment CFR 47 FCC Rules
3. and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION amp Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment Use the supplied DC power supply to feed power to the machine Please use recommended interconnection cables to connect the machine to other components FCC and CE approved using STP cable for twisted pair products 10 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000693 REV 1
4. ECHNOLOGY Install the Kramer RK 1UTB Under the Table Enclosure 5 Install the Kramer RK 1UTB Under the Table Enclosure To install the RK 1UTB you have to Mount the Kramer devices on the RK 1UTB see section 5 1 Attach the RK 1UTB under the table see section 5 2 Install the cables see section 5 3 This section also describes how to Mount units that do not have underside screw holes see section 5 4 Connect a blank panel optional see section 5 5 5 1 Mount the Kramer devices on the RK 1UTB The example illustrated in Figure 1 shows the Kramer VP 100A a half 19 unit with these two wall plate inserts the WRR and W H 5 1 1 Installing the Required Kramer Inserts To mount a Kramer insert or connector module do the following 1 5 1 2 Unscrew the two screws that fasten the blank plate to the connecting surface and remove the blank plate Place the required Kramer insert over the opening insert the two screws to fix the Kramer insert in place and tighten them Mounting the Kramer TOOL The RK 1UTB underside TOOL mounting area includes a set of screw holes that are suitable for any combination of units to be mounted To mount a unit on the RK 1UTB as illustrated in Figure 2 do the following l 2 Place the first unit on the rack for example the Kramer VP 100A Hold both the VP 100A and the RK 1UTB with your hands and turn them upside down Insert the appropriate amount of screws through
5. Kramer Electronics Ltd USER MANUAL Model RK 1UTB Under the Table Enclosure Contents Contents 1 Introduction 2 Getting Started 3 Overview 3 1 Recommendations for Best Performance 4 Your Kramer RK 1UTB Under the Table Enclosure 5 Install the Kramer RK 1UTB Under the Table Enclosure 5 1 Mount the Kramer devices on the RK 1UTB 5 1 1 Installing the Required Kramer Inserts 5 1 2 Mounting the Kramer TOOL 52 Securing the RK 1UTB Enclosure to the Table 53 Installing the Cables 5 4 Mounting Units that do not have Underside Screw Holes 5 3 Connecting a Blank Panel to the RK 1UTB 6 Technical Specifications Figures Figure 1 RK 1UTB Under a Table Figure 2 RK 1UTB Under the Table Enclosure Figure 3 RK 1UTB Under the Table Enclosure Underside Figure 4 Securing the RK 1UTB to the Underneath of the Table Figure 5 Mounting a half 19 unit via Screws on the RK 1UTB Side Panel Figure 6 RK 1UTB Rack Adapter Connecting a Blank Panel Tables Table 1 Using the RK 1UTB Table 2 RK 1UTB Blank Panels Part Numbers Table 3 RK 1UTB Under the Table Enclosure Features Table 4 Technical Specifications of the RK 1UTB ONN DAANAN A UN m CDaanntbv Oo BWW Introduction 1 Introduction Welcome to Kramer Electronics Since 1981 Kramer Electronics has been providing a world of unique creative and affordable solutions to the vast range of problems that confront the video audio presentat
6. able 4 includes the technical specifications Table 4 Technical Specifications of the RK 1UTB DIMENSIONS 19 inch W 7 inch D 1U H WEIGHT 1 2kg 2 65lbs approx ACCESSORIES 10 M3x5 screws six 4X3 8 screws OPTIONS Blank panels 1 Specifications are subject to change without notice 2 One half 19 blank panel P N 60 900013 1 4U 19 blank panel P N 60 900014 1 8U 19 blank panel P N 60 900015 LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHAT IS COVERED AND WHAT IS NOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com Any product on which the serial number has been defaced modified or removed or on which the WARRANTY VOID IF TAMPERED sticker has been torn reattached removed or otherwise interfered with Damage deteri
7. he installation Connect only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables Avoid interference from neighboring electrical appliances and position your rack adapter on the rack away from moisture excessive sunlight and dust 1 Each product is measured in inches Your Kramer RK 1 UTB Under the Table Enclosure 4 Your Kramer RK 1UTB Under the Table Enclosure Figure 2 and Table 3 define the RK 1UTB Rear View Front View Figure 2 RK 1UTB Under the Table Enclosure Table 3 RK 1UTB Under the Table Enclosure Features Feature Function 1 Rim Screw Holes For fixing the RK 1UTB under the table 3 on each side 2 TOOL Mounting Area Space for mounting a Kramer TOOL Underside includes a set of screw holes that are suitable for the units to be mounted 3 Kramer Insert see section 5 1 1 A blank cover that can be replaced with a Kramer insert as 4 required 5 Power Socket Connect to power a peripheral device 6 Power Socket Connect to power a peripheral device 7 Power Socket 6 3A Connect to the mains power 8 Power Socket Connect to power the Kramer machine 1 One half 19 1U unit or a combination of 1 4 19 1U units and 1 8 19 1U units 2 Suitable for the USA version power requirements 110V 4 KRAMER SIMPLE CREATIVE T
8. ion and broadcasting professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 1 000 plus different models now appear in 11 groups that are clearly defined by function Congratulations on purchasing your Kramer RK 1UTB Under the Table Enclosure a furniture mounted adapter which is ideal for boardrooms conference and training rooms The package includes the following items e RK 1UTB Under the Table Enclosure e Additional mechanical parts screws nuts and so on pP e This user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual 1 GROUP 1 Distribution Amplifiers GROUP 2 Switchers and Matrix Switchers GROUP 3 Control Systems GROUP 4 Format Standards Converters GROUP 5 Range Extenders and Repeaters GROUP 6 Specialty AV Products GROUP 7 Scan Converters and Scalers GROUP 8 Cables and Connectors GROUP 9 Room Connectivity GROUP 10 Accessories and Rack Adapters GROUP 11 Sierra Products 2 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com 1 Overview 3 Overview The RK 1UTB is an under the table enclosure that is easily installed underneath a wooden table or podium top The unit is sturdy cost effective and easy to in
9. oration or malfunction resulting from i Accident misuse abuse neglect fire water lightning or other acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repair or attempted repair by anyone not authorized by Kramer iv Any shipment of the product claims must be presented to the carrier v Removalor installation of the product vi Any other cause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following L 2 3 Removal or installations charges Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased Shipping charges HOW YOU CAN GET WARRANTY SERVICE 1 2 3 To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem s For the name of the nearest Kramer authorized service center
10. stall The RK 1UTB e Lets you install one half 19 1U unit or a combination of 1 4 19 1U units and 1 8 19 1U units The examples in Table illustrate how different products can be combined e Includes three USA power sockets e Lets you install up to two wall plate inserts according to your requirements Figure 1 RK 1UTB Under a Table 1 For details of Kramer s wall plate devices and module connectors see our Web site at http www kramerelectronics com 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview Table 1 Using the RK 1UTB Mounting Kramer products on the RK 1UTB For example e One VP 100A unit 1 2 e Two 104B units 1 4 1 4 e One 104B unit 1 4 vel We e One PS 1DVI unit e One PT 1PS unit e Four PS 1DVI units 1 8 1 8 1 8 1 8 The RK 1UTB does not have to be entirely full with mounted units You can use the optional blank panels defined in Table 2 to fill the empty spaces Table 2 RK 1UTB Blank Panels Part Numbers Blank Panel Description Part Number PNL BLANK 1 2U 19 60 900013 PNL BLANK 1 4U 19 60 900014 PNL BLANK 1 8U 19 60 900015 3 1 Recommendations for Best Performance We recommend that you Have a Philips screwdriver available Disconnect the mains voltage and all cables connected to each machine that is being mounted in the rack adapter before proceeding with t
11. the holes on the RK 1UTB that fit the holes on the underside of the VP 100A using the M3x5 screws supplied with the unit as illustrated in Figure 3 Tighten the screws Rotate the RK 1UTB horizontally with the unit connected 1 When connecting several units as defined in Table 1 place the next unit and then repeat steps 2 to 5 Install the Kramer RK 1UTB Under the Table Enclosure Figure 3 RK 1UTB Under the Table Enclosure Underside 5 2 Securing the RK 1UTB Enclosure to the Table To install the RK 1UTB underneath the table as illustrated in Figure 4 do the following 1 Place the unit to the underside of the table and mark the correct location 2 Insert the six M4 2X16 wood screws into the six rim screw holes three on each side and fix the RK 1UTB to the table Figure 4 Securing the RK 1UTB to the Underneath of the Table 6 KRAMER SIMPLE CREATIVE TECHNOLOGY Install the Kramer RK 1UTB Under the Table Enclosure 5 3 Installing the Cables To install the cables do the following 1 Connect the cables on the rear side of the unit 2 Connect the Kramer machine for example the VP 100A to the power socket The RK 1UTB can accommodate 12V 500mA 5 2V and 2A DC power adapters If the machine installed requires a larger size power adapter we recommend using the Kramer 12V desktop power supply with a DC plug which fits easily into the rear side of the RK 1UTB enclosure
Download Pdf Manuals
Related Search