Hobby Zone Super Cub S
Contents
1. CAUTION When connecting the battery to the battery charger make sure the connectors are aligned as shown Failure to connect the battery properly could cause the terminals to short and result in fire personal injury and or property damage Charger Specifications e Input power 10 14V e Max output voltage 11 1V e Fixed charge current 1 3A e Balances and charges 3S Li Po cells with a minimum capacity of 1250mAh This charger may be connected to the AC adapter included with your model READY TO FLY DX4e Transmitter Remove the battery cover install the four included batteries noting proper polarity and reinstall the battery cover SAFE Mode Switch Throttle Trim Throttle Low Battery Alarm When the battery voltage drops below 4 7 volts an alarm sounds and the voltage LEDs flash The batteries must be replaced immediately If this happens while flying land your aircraft as soon and as safely as possible A WARNING Do not pick up the transmitter by the antenna Do not alter or put weight on the antenna Damage to antenna parts can decrease transmitter signal strength which can result in loss of model control injury or property damage Nobbyz Es ne 4 Button Super Cub S Flashing Charging Solid Charged Elevator Trim Elevator Steering Steering Trim Power Switch Mode 2 show2. ACRO 3 Set REVERSE Gear Channel 4 Go to ADJUST LIST MENU 5 Set TRAVEL ADJ Gear Fmode 0 100 Gear Fmode 1 40 6 Set FLAPS Norm 100 LAND 100 7 Set MIX 1 ACT Gear Gear ACT RATE D 0 U 100 SW MIX TRIM INH Resulting in The Gear and Mix switches operate the 3 SAFE modes Gear 0 Mix 0 Beginner Mode Gear 1 Mix 0 Intermediate Mode Gear 1 Mix 1 Advanced Mode The Flap switch operates Panic Recovery Position 0 Off Position 1 On not a momentary switch 1 Go to the SYSTEM SETUP 2 Set MODEL TYPE AIRPLANE 3 Set SWITCH SELECT Change all to INH then GEAR AUX1 FLAP GEAR 4 Go to the FUNCTION LIST 5 Set SERVO SETUP Reverse AUX1 Resulting in Flap Gyro Switch operates the 3 SAFE modes 0 beginner 1 intermediate 2 advanced The Trainer Bind button operates Panic Recovery 1 Go to the SYSTEM SETUP 2 Set MODEL TYPE AIRPLANE 3 Set CHANNEL ASSIGN click NEXT to go to Channel Input Config GEAR D AUX1 i 4 Go to the FUNCTION LIST 5 Set SERVO SETUP Reverse AUX1 Resulting in Switch D operates the 3 SAFE modes 0 beginner 1 intermediate 2 advanced The Bind I button operates Panic Recovery 11 BNF e RTF EN Low Voltage Cutoff LVC NOTICE Repeated flying to when the motor pulses will damage the battery For your first flights set a timer for 7 minutes to avoid flying until the motor pulses Adjust your timer for longer or sho
3. Nobbyz ne 10 Super Cub S EN Setup for Optional BNE Transmitters BNF z z To operate the SAFE system in this aircraft set up Non Computerized Transmitter Setup your optional DSM2 DSMX transmitter using the DX4e and DX5e chart below SAFF SAFE Flight l Transmitter mode Panic Recovery Switch Modes S rted SAFE Flight mode is selected using switch dee da Channel 5 signal high middle low Throttle Aileron Elevator and Rudder in Normal Position DNA ACT AUX Panic Recovery mode is selected with i i Channel 6 signal high low 2pos switch switch Trainer Button 2 Pos Flight Mode DX4e CH 5 IMPORTANT A transmitter with a 2 position Channel i Trainer Button 3 Pos Flight Mode 5 switch will only allow the use of position 0 or posi 3pos switch switch tion 2 flight modes If possible refer to your transmit DX5e CH5 i ter manual assign Channel 5 in your transmitter to a 2pos switch switch Trainer Switch 2 Pos Flight Mode 3 position switch to operate all 3 flight modes DX5e CH5 Refer to your transmitter s manual for more 3pos switch switch Trainer Switch APOS FIGO MOGE information about transmitter setup Computerized Transmitter Setup DX6i DX7S DX8 DX9 DX18 and DX1800 Start all transmitter programming with a blank model do a model reset then name the model HIGH 100 LOW 70 Set Dual Rates to 1 Go to the SETUP LIST MENU 2 Set MODELTYPE
4. descend Experienced SAFE Flight Mode Restrain the aircraft so it does not escape your control while you are testing your transmitter controls Move the sticks on the transmitter to ensure the aircraft responds as shown Turn Right S Turn Left If your model does not respond as shown DO NOT FLY Refer to the Troubleshooting Guide in this manual for more information If you need more assistance contact the appropriate Horizon Hobby Product Support department H the aircraft responds as shown move the SAFE flight mode switch to Beginner mode position 0 to prepare to fly Beginner SAFE Flight Mode Trimming If your aircraft does not fly straight and level at half 1 westanm Required throttle with the steering stick at center switch to um Intermediate or Experienced mode then fly into the wind and move the trim sliders If you move a trim slider more than 8 clicks in one direction land and adjust the clevis Observe the rudder or elevator surface while the trim slider is off center Center the slider Disconnect the clevis then adjust and connect it again so the surface is in the position you observed Perform test flights as needed hobbyzane 8 Super Cub S EN Takeoff Hand Launch Hand launch in
5. to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call the toll free telephone number referenced in the 15 Warranty and Service Contact Information section to speak with a Product Support representative Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional pr
6. transmitter until another binding Assembly Landing Gear Installation 5 BNF e RTF EN Super Cub S Assembly continued Tail Installation Gently flex wee SIN Kai Clevis adjustment Control Horn Wing Installation S IMPORTANT The rubber bands prevent wing damage from impact Always replace worn or broken rubber bands SON Nobbyz ne 6 Super Cub S EN Installing the Flight Battery 1 Lower the throttle and throttle trim then power on the transmitter for at least 5 seconds CAUTION Always disconnect the Li Po flight battery from the aircraft receiver when not flying to avoid over discharging the battery Batteries discharged to a voltage lower than the lowest approved voltage may become damaged resulting in loss of performance and potential fire when batteries are charged A m E E E SS will move then return to center when the aircraft is ready to fly Keep immobile and out of the wind for 5 seconds The aircraft can be held immobile for 5 seconds at any angle convenient for you to connect the battery 7 BNF e RTF EN Super Cub S Control Direction Test Perform the Control Direction Test with the Up Elevator climb transmitter SAFE flight mode switch set to p Experienced mode position 2 Down Elevator
7. Beginner mode for first flights Get help to hand launch your aircraft so you can concentrate on flying If you must hand launch the aircraft alone hold the model in your dominant hand and the transmitter in your other hand An optional neck strap SPMP610 sold separately can help you hold the transmitter NO GE Wind 0 7 mph 0 11km h Beginner Mode SAFE Switch Position 0 Easy Launching Launching is easier in Beginner mode if you hold the Panic Recovery button Press and hold the button then increase the throttle to 100 Launch the aircraft When the aircraft is up where you want to fly release the button and decrease the throttle to 50 60 Ground Launch Use the Beginner mode for takeoff in first flights If the ground is not hard and level get help to hand Wind 0 7 mph launch your aircraft 0 11km h Gently pull back on the elevator stick to lift off of the ground Ka ft 10 ma 9 BNF RTF EN Super Cub S Flying In Beginner mode when properly trimmed your aircraft will climb at full throttle without use of the elevator stick e The aircraft flies 7 minutes or more on a battery charge using proper throttle management If the motor pulses land the aircraft immediately and recharge the flight battery Make small and steady control stick movements for smooth control of your aircraft Let the aircraft climb at full t
8. Super Gub 5 Instruction Manual e Bedienungsanleitung e Manuel d utilisation e Manuale di Istruzioni SN RTF BNF hobbyzane Bind N Fly Ready to fly redefined EN Super Cub S NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby LLC For up to date product literature visit www horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some ba
9. UI too high setting responds to other Throttle channel is reversed Reverse throttle channel on transmitter controls Motor disconnected from Receiver ESC Make sure motor is connected to the Receiver ESC a propeller and spinner shaft Replace damaged parts Extra propeller noise or Propeller is out of balance Balance or replace propeller extra vibration Prop nut is too loose Tighten the prop nut pinner is damaged or loose Repair or replace damaged spinner light battery charge is low Completely recharge flight battery ropeller installed backwards Install propeller with numbers facing forward light battery damaged Replace flight battery and follow flight battery instructions light conditions may be too cold Make sure battery is warm before use Move powered transmitter a few feet from aircraft disconnect and i reconnect flight battery to aircraft Aircraft will not Bind j itter 1 SCH during binding to metal object wireless source or another Move aircraft and transmitter to another location and attempt binding transmitter transmitter agan Refer to the transmit Reduced flight time or aircraft underpowered SH 59 2 3 os o St of oS n O2 CD D D be lt p D ha red CH ess Q gt CH pl DI h O kee D CO 3 D 77 O O Q O CO CD O D Q cD CO O ter manual for binding Flight battery transmitter battery charge Replace rech
10. V1 9 2 2012 EN 301 489 17 V2 1 1 2009 EN60950 1 2006 A11 2009 A1 2010 A12 2011 EN55022 2010 AC 2011 EN55024 2010 EN61000 3 2 2006 A1 2009 A2 2009 EN61000 3 3 2008 Robert Peak Signed for and on behalf of Chief Financial Officer Horizon Hobby Inc Champaign IL USA Horizon Hobby Inc March 26 2014 Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2014032602 Product s HBZ Super Cub SAFE BNF Item Number s HBZ8180EU HBZ8180UK Equipment class 1 The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE Directive 1999 5 EC EMC Directive 2004 108 EC and LVD Directive 2006 95 EC EN 301 489 1 V1 9 2 2012 EN 301 489 17 V2 1 1 2009 EN60950 1 2006 A11 2009 A1 2010 A12 2011 EN55022 2010 AC 2011 EN55024 2010 EN61000 3 2 2006 A1 2009 A2 2009 EN61000 3 3 2008 Robert Peak Signed for and on behalf of Chief Financial Officer Horizon Hobby Inc Champaign IL USA Horizon Hobby Inc March 26 2014 Instructions for disposal of WEEE by users in the European Union equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment XK This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste The separate collection and recycling of your waste equipme
11. arge batteries instructions too Bind switch or button not held long Power off transmitter and repeat bind process Hold transmitter bind enough during bind process button or switch until receiver is bound OQ 0 35 O a LO 193 sig st ES oO 03 SE D o s Zi 9 O fav Oo O Q CO cD gt Q O DD i CD Q i Move powered transmitter a few feet from aircraft disconnect and connecting process reconnect flight battery to aircraft Aircraft will not l j ei art l j ect wireless source or another si adn transmitter to another location and attempt to transmitter transmitter efer to the transmit Flight GEN ransmitter battery charge Replace recharge batteries ter manual for binding de Transmitter may have been bound to a a different aircraft using different DSM Bind aircraft to transmitter protocol Control surface control horn linkage or servo damage Replace or repair damaged parts and adjust controls Do a check of wires and connections connect or replace as needed light battery charge is low Fully recharge flight battery eceiver is damaged Replace Receiver not move Perform the Control Direction Test and adjust the controls on transmit ter appropriately Controls reversed ormal Low Voltage Cutoff LVC Recharge flight battery or replace battery that is no longer performing Motor power pulses Weather conditions might be too cold Postpone flight until weather is warmer then motor l
12. aube White Rubber Bands 6 weiBe Gummibander 6 cao and Clevis Schubstangen mit Clips 2 6 4 Gearbox with Firewall Getriebe mit Motorspant E Screws 2 M Motorschrauben M2 5x6 2 2 no Motor with Pinion Motor mit Ritzel Metal Pinion Metalritzel 2 Bare Fuselage receiver Schaumteilesatz o Elektronik Decal Sheet Super Cub Dekorbogen Mini Servo 3W with Parkzone Mini Servo 3 adrig Arms Short Lead kurzes Kabel Servo Gear Set Servo Hebel Set Servo Arm Assortment 3W amp 5W Servo Getriebe 3W amp 5W Dx4e 4 Channel Full Spektrum DX4e 4 Kanal Modo AT y Sender ohne Empf nger MD 2 Ran se Transmitter On dE Mode 1 Y Sender ohne Empfanger MD 1 65 Description H lice 9x6 Chargeur quilibreur Li Po DC Alimentation secteur 1 5A Module RX SAFE Vario Batterie Li Po 3S 11 1V 1300mA avec prise EC3 Axe d h lice Train d atterrissage avec roues Cone Couvercle de compartiment a batterie Cloison pare feu avec vis Roulette de queue Aile standard avec haubans Guignols 4 Hauban avec vis 2 tiges de fixation d aile Empennages avec acces soires Capot Elastiques blancs Set de tringleries avec chapes R ducteur Moteur avec pignon Vis de fixation moteur M2 5x6 2 Pignon m tal 2 Fuselage nu Planche de d coration Mini servo 3 fils avec bras fils courts Set de pignons pour servo Assortiment de bras de servo Emetteur seul DX4e 4 voies Mod
13. cifically designed and protected for this purpose Moisture causes damage to electronics e Never place any portion of the model in your mouth as it could cause serious injury or even death e Never operate your model with low transmitter batteries e Always keep aircraft in sight and under control e Always use fully charged batteries e Always keep transmitter powered on while aircraft is powered e Always remove batteries before disassembly e Always keep moving parts clean e Always keep parts dry e Always let parts cool after use before touching e Always remove batteries after use e Always ensure failsafe is properly set before flying e Never operate aircraft with damaged wiring e Never touch moving parts Always inspect the battery before charging and never charge dead or damaged batteries Always disconnect the battery after charging and let the charger cool between charges Always constantly monitor the temperature of the battery pack while charging ONLY USE A CHARGER SPECIFICALLY DESIGNED TO CHARGE LI PO BATTERIES Failure to charge the battery with a compatible charger may cause fire resulting in personal injury and or property damage Never discharge Li Po cells to below 3V under load Never cover warning labels with hook and loop strips Never leave charging batteries unattended Never charge batteries outside recommended levels Never attempt to dismantle or alter the charger Never allow minors unde
14. e Repairs and Repair Requests questForm www quickbase com db Horizon Product Support bghj7ey8c a GenNewRecord 4105 Fieldstone Rd Air 888 959 2305 Sales sales horizonhobby com Air 888 959 2305 United States of America Product Technical Assistance Champaign Illinois 61822 USA United Kinadom Service Parts Sales sales horizonhobby co uk Units 1 4 Ployters Rd Staple Tye 9 Horizon Hobby Limited 44 0 1279 641 097 Harlow Essex CM18 7NS United Kingdom Horizon Technischer Service service horizonhobby de Christian Junge StraBe 1 Sales Horizon Hobby GmbH 49 0 4121 2655 100 25337 Elmshorn Germany ee Service Parts Sales infofrance horizonhobby com 11 Rue Georges Charpak Horizon Hobby SAS 33 0 1 60 18 34 90 71127 Lieusaint France China Service Parts Sales info horizonhobby com cn Room 506 No 97 Changshou Rd Horizon Hobby China 86 021 5180 9868 Shanghai China 200060 FCC Information Operation is subject to the following two conditions 1 This device Antenna Separation Distance may not cause harmful interference and 2 this device must When operating your transmitter accept any interference received including interference that may please be sure to maintain a Cause undesired operation separation distance of at least 5 cm between your body excluding fingers CAUTION Changes or modifications not expressly hands wrists ankles and feet and approved by the party responsible for compliance could
15. e 2 Emetteur seul DX4e 4 voies Mode 1 Descrizione 9 x 6 Elica DC LiPo Caricatore con bilanciamento 1 5A AC Alimentatore Unita ricevitore ESC DSMX N D TI rm 1300mAh 11 1V Li Po Bat tery with EC3 Connector Albero elica Carrello con ruote Ogiva Portello batteria con chiusura Ordinata motore con viti Ruotino coda Ala standard con montanti Squadrette 4 Montanti ala con viti 2 aste fissaggio ala Coda con accessori Capottina Elastici bianchi 6 Set barrette e forcelle 2 Riduttore con ordinata Motore con pignone Viti motore 2 M 2 5 x 6 Pignone in metallo 2 Solo fusoliera senza ricevitore Foglio adesivi Servo mini 3W con squad rette filo corto Set ingranaggi servo Assortimento squadrette Servo Solo Tx 4 canali DX4e DSMX MD2 Solo Tx 4 canali DX4e DSMX MD1 BNF e RTF IT Super Cub S Optional Parts e Optionale Bauteile e Pieces optionnelles e Pezzi opzionali Part Nummer Numero Codice Hobbyzone Schwimmersatz HBZ7390 Super Cub LP Floats fiir Super Cub LP Super Cub LP Floats 10 x 8 High Power High Power Luftschraube i Elica 10x8 per alta potenza PKZ1005 Propeller for use with 10 x8 bei Verwendung mit Ee da usare con i galleggianti optional floats Schwimmern opzionali EC3 Charge Lead w 12 Prise de charge EC3 long Cavo di carica EC3 da EFLAEC312 Wire amp Jacks 16AWG EES Ee 30cm con jacks 16AWG Pinze tipo coccodrillo Alligator C
16. f Horizon Hobby LLC The Spektrum trademark is used with permission of Bachmann Industries Inc Patents pending www hobbyzonerc com Created 06 14 42980 1 HBZ8100 HBZ8180
17. hold a charge Wind 0 7 mph 0 11km h Post Flight NOTICE When you are finished flying never leave the aircraft in direct sunlight or in a hot enclosed area such as a car Doing so can damage the foam Post Flight Checklist 1 Disconnect flight battery from the aircraft Required for Safety 2 Remove flight battery from the aircraft a Power off transmitter Recharge flight battery Repair or replace all damaged parts i Store flight battery apart from the aircraft and monitor the battery charge planning for future flights 12 Super Cub S EN Troubleshooting Guide Problem Possible Cause Solution Damaged propeller or spinner Replace propeller or spinner Loose or damaged spinner propeller Replace parts or correctly align all parts and tighten fasteners motor or gear box parts as needed Aircraft oscillates Loose receiver Align and secure receiver in fuselage Tighten or otherwise secure parts Servo arm linkage horn and Loose aircraft controls control surface Replace worn parts especially propeller spinner or servo Trim is at extreme and e i im i If you need to adjust trim more than 8 clicks return the trim to neutral net eae fly Trim is not at neutral and manually adjust the clevis to mechanically remove trim Throttle not at lowest position or throttle Reset controls with throttle stick and throttle trim at lowest Aircraft will not re spond to throttle but
18. hrottle into the wind until the aircraft gets about 150 feet 46 meters above the ground then decrease the throttle to Full throttle 50 throttle Reduced throttle half 50 Flying with the nose pointed toward you is one of the hardest things to do when learning to fly To practice piloting the aircraft try flying in large circles high off the ground lt SAFE Technology Flight Modes Beginner Mode Pitch nose up and down and Roll wing tips up and down angles are limited to help you keep the aircraft airborne Pitch Roll Beginner Mode Self leveling Switch Position 0 Intermediate Mode The pilot is only prevented from entering extreme flight conditions Experienced Mode Unlimited Flight Envelope Panic Recovery Mode Intermediate Mode If you feel you have Switch Position 1 lost control in any mode hold the Panic Recovery button The SAFE technology will return the aircraft to a stable attitude wings level with a slight climb Always fly at a safe altitude as Panic Recovery may cause the aircraft to lose some Pitch Roll altitude when leveling the wings Release the l Panic Recovery button to turn off Panic mode Experienced Mode NOTICE If the aircraft is and return to the current SAFE flight mode Switch Position 2 upside down when the Panic Recovery button is pressed sufficient altitude is required for the aircraft to return to straight and level flight
19. lip 12V Krokodilklemme 12 V Adaptateur 12V allume cigare HBZ6513 adattatore 12V per presa Lighter Adapter Zigarettenanzunder pinces croco accendisigari HBZ1004 1 5A AC Power Supply 1 5A AC Power Supply US Alimentation secteur 1 5A 1 5A AC Alimentatore solo US Only Only USA uniquement USA HBZ1004EU 1 5A AC Power Supply 1 5A AC Power Supply EU Alimentation secteur 1 5A EU 1 5A AC Alimentatore solo EU Only Only uniquement EU UK nly 2 Description Beschreibung Description Descrizione HBZ1004UK 1 5A AC Power Supply 1 5A AC Power Supply Alimentation secteur 1 5A UK 1 5A AC Alimentatore solo UK Only 0 uniquement UK Li Po Cell Voltage NI Testeur de tension pour bat EFLA111 Checker E flite Li Po Cell Volt Checker tenia li Po EFLA250 Park Flyer Tool Assort E flite Park Flyer Werkzeug Assortiment d outils pour ment 5 pc sortiment 5 teilig parkflyer 5 pieces Park Flyer r Voltmetro per celle LiPo Assortimento attrezzi per EC2 dispositivo amp connet tore batteria EC2 Device amp Battery Prise EC2 cot contr leur et EFLAEC203 E flite EC2 Stecker Buchse cote batterie Celectra 80W AC DC Celectra 80 W AC DC EFLC3025 Multi Chemistry Battery Multi Chemistry Batteriela Ge ee DC Charger deger t Seati pes RTM40R5510 Phoenix R C Pro Simula Phoenix R C Pro Simulator Simulateur Phoenix V4 avec tor V4 0 w DX5e Mode 2 V4 0 m DX5e DX5e mode 2 RTM4000 EE R C Pro Simula an R C Pr
20. medy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either i service or ii replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition
21. n For more information on the transmitter go to www horizonhobby com products SPMR4400 and click on the support tab for the Spektrum DX4e to download the instruction manual Super Cub S EN v Binding Procedure Reference Table Transmitter Binding m 1 Make sure the transmitter is powered off 2 Make sure the transmitter controls are neutral the throttle and throttle trim are BIND PLUG CE READY TO FLY deeg position and the aircraft is The included RTF transmitter should be bound to the aircraft at the factory but if you need to re bind E 3 Install bind plug in the receiver bind port follow the binding procedure as shown 4 Connect the flight battery in the aircraft The receiver LED will begin to flash By Power on the transmitter while holding on Ej VE EE You need to bind your chosen Spektrum DSM2 When the receiver binds to the transmit ter the light on the receiver will turn solid The motor will arm with throttle and DSMX technology equipped aircraft transmitter to the receiver for proper operation Please refer to the Be optional parts list in this manual or visit throttle trim at the lowest position www bindnfly com for a list of compatible transmit a 7 Release the Bind button and remove the i H ters bind plug from the receiver 8 Disconnect the flight battery from the aircraft then power off the transmitter The receiver should retain the binding instructions received from the
22. nt at the time of disposal will help to conserve natural resources pu 2nd ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product BNF e RTF Part Nummer Num ro Codice HBZ1002 HBZ1003 HBZ1004 SPMA3170 PKZ1033 HBZ7104 HBZ7106 HBZ7107 HBZ7112 HBZ7114 HBZ7117 HBZ7120 HBZ7121 HBZ7122 HBZ7124 HBZ7125 HBZ7126 HBZ7127 HBZ7128 HBZ7129 HBZ7134 PKZ1536 HBZ7135 HBZ8167 HBZ8110 PKZ1060 PKZ1062 PKZ1132 SPMR4400 SPMR4401 Super Cub S Description Beschreibung 9 x 6 Propeller 9 x 6 Propeller DC LiPo Balancing Hobbyzone 3S Lipo Balance Charger Lader 1 5A AC Power Supply Hobbyzone 1 5A Netzteil DSMX SAFE Receiver DSMX SAFE Empfanger ESC unit Super Cub Regler Einheit 1300mAh 11 1V Li Po Parkzone 11 1V 1300mAh Battery with EGS Con ipo Bat m EC3 Stecker Luftschraubenwelle mit operat Zubeh r anding Gear with Tires Fahrwerk m Bereifung Spinner rewall with Screws Brandschott Tail Wheel L Battery Door with Latch Super Cub Batteriefachdeckel Fi t Wing Struts with Screws Tragfl chenstreben 2 Wing Hold Down Rods Tragfl chend bel Standard Wing with P Control Horns Ruderhorner 4 Tail with Accessories komplettes Leitwerk Motorh
23. o Simulator Simulateur Phoenixia DX4e DSMX 4 Channel Spektrum DX4e DSMX 4 Kanal Sender ohne Empf nger Emetteur DX4e DSMX 4 voies DX5e DSMX 5 Channel Spektrum DX5e DSMX 5 Kanal e Sender ohne Empf nger Emetteur DX5e DSMX 5 voies DX6i DSMX 6 Channel Spektrum DX6i DSMX 6 Kanal Sender ohne Empfanger Emetteur DX6i DSMX 6 voies DX7s DSMX 7 Channel Spektrum DX7s DSMX 7 Kanal Transmitter Sender ohne Empf nger Emetteur DX7s DSMX 7 voies DX8 DSMX 8 Channel Spektrum DX8 DSMX 8 Kanal DX8 DSMX Trasmettitore 8 DX9 DSMX 9 Channel Spektrum DX9 DSMX 9 Kanal DX9 DSMX Trasmettitore 9 DX10t DSMX 10 Channel Spektrum DX10t DSMX 10 Emetteur DX10t DSMX 10 DX10t DSMX Trasmettitore Transmitter Kanal Sender ohne Empf nger voies 10 canali DX18 DSMX 18 Channel Spektrum DX18 DSMX 18 DX18 DSMX Trasmettitore Caricabatterie per batteria multichimica 80 W c a c c Phoenix R C Pro simula toreV4 0 w DX5e Mode 2 Phoenix R C Pro simulatore heck EFLAEC202 Geer Connec E flite EC2 Akkubuchse Prise EC2 cot batterie 2 EC2 Connettore batteria 2 h DX4e DSMX Trasmettitore 4 canali DX5e DSMX Trasmettitore 5 canali DX6i DSMX Trasmettitore 6 canali DX7s DSMX Trasmettitore 7 canali lt gt AR hobbyzeane 66 2014 Horizon Hobby LLC HobbyZone the HobbyZone logo SAFE SAFE logo Bind N Fly the BNF logo Z Foam DSM DSM2 DSMX EC2 EC3 Celectra and the Horizon Hobby logo are trademarks or registered trademarks o
24. oses 7 power Battery is old worn out or damaged Replace battery Battery C rating might be too small Use recommended battery CD D O o Control surface does zl D DIS ei 5 D SI QQ D SES S e D di Fr o 5 QQ a 3 gt 5 CD CD Es la D d Se 2 LO CD lt 13 BNF e RTF EN Super Cub S Service and Repair NOTICE If you replace the receiver install the new receiver in the same orientation and manner as the original receiver or damage may result Thanks to the Z Foam material in the wing and fuselage of this aircraft repairs to the foam can be made using virtually any adhesive hot glue regular CA cyanoacrylate adhesive epoxy etc However use only foam compatible CA foam com patible accelerant or epoxy on the vertical and horizontal tail material Disassembly CAUTION DO NOT handle the spinner propeller motor or Receiver ESC unit while the battery is connected to the Receiver ESC Personal injury could result 1 Remove the spinner A from the hex nut 2 Remove the hex nut B washer C and propeller D from the gear shaft E 3 Remove 3 screws F and the cowling G from the fuselage 4 Remove 4 screws H 4 washers I and the gearbox J from the firewall 5 Inthe fuselage disconnect 2 bullet connectors of the motor K from the ESC connectors motor wire colors align with ESC wire colors and remove the motor wires from
25. otection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content _service center_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When Calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be cove
26. r the age of 14 to charge battery packs Never charge batteries in extremely hot or cold places recom mended between 40 120 F or 5 49 C or place in direct sunlight Super Cub S Included in the Box READY TO FLY Includes Transmitter T lt 5 3000000000000 EN For more information and to register your product online visit www hobbyzonerc com un een na D Ze K NNS S E TTT LIT EE OG IT NITIA LA aenant 8 se D 183 m Flyin thi area a upwind of pilot i stand here Flying Tips Sensor Assisted Flight Envelope SAFE technology is designed as flight assistance not an autopilot The pilot is always in control and required to fly the aircraft at all times Start in Beginner mode SAFE switch position 0 As you learn and become more confident change modes to advance your flying skills Always keep your aircraft in plain sight and upwind from you Do not attempt your first turn at low altitude Higher altitudes allow for greater possibility of correction Always make deliberate and steady control stick movements for smooth control of your aircraft Preflight Checklist 1 Find a safe and open area 2 Charge flight battery BNF e RTF EN Charging the Flight Battery A
27. red by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditions found on our website http www horizonhobby com content _ service center_render service center ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non compliant Product will not be serviced Further the sender will be responsible for arranging return shipment of the un serviced Product through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a period of 60 days from notification after which it will be discarded BNF e RTF EN Super Cub S Warranty and Service Contact Information Country of Purchase Horizon Hobby Contact Information Address Horizon Service Center servicecenter horizonhobby com R
28. rter flights once you have flown the aircraft Landing Land the aircraft in Beginner mode CAUTION Never catch a flying aircraft in your hands Doing so could cause personal injury and damage to the aircraft A Easy Landing Landing is easier if you hold the Panic Recovery button Line up for your landing decrease the throttle to 0 and press and hold the Panic Recovery button The aircraft will glide down wings level with the nose up flared for landing d NOTICE If a crash is imminent reduce the throttle Failure to do so could result in extra damage to the airframe as well as damage to the receiver and motor decrease throttle at propeller strike NOTICE Crash damage is not covered under Warranty Prolong Battery Life e Before storage charge your battery to about half capacity Capacity decreases with use and age e During storage ensure the charge does not fall below 3V per cell uc hobbyz ne Super Cub S FWA e The aircraft protects the flight battery from accidental over discharge by applying LVC removing power supplied to the motor LVC causes the motor to pulse but power remains to steer the aircraft If the motor pulses land immediately and recharge the flight battery After use disconnect and remove the battery from the aircraft to prevent trickle discharge If the Li Po battery is discharged below 3V per cell it will not
29. sic mechanical ability Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby LLC This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy A WARNING AGAINST COUNTERFEIT PRODUCTS If you ever need to replace your Spektrum product found in a Horizon Hobby product always purchase from Horizon Hobby LLC or a Horizon Hobby authorized dealer to ensure authentic high quality Spektrum product Horizon Hobby LLC disclaims all support and warranty with regards but not limited to compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum Safety Precautions and Warnings As the user of this product you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others e Always keep a safe distance in all directions around your model to avoid collisions or injur
30. the antenna to meet RF exposure void the user s authority to operate the equipment safety requirements as determined by FCC regulations This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the This illustration show the applicable regulations governing a radio transmitter in the approximate 5 cm RF exposure area 2 400GHz to 2 4835GHz frequency range and typical hand placement when operating your transmitter IC Information This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device hobbyzeane 16 Super Cub S EN Compliance Information for the European Union HR HU ie iT LT Lu v mT Ne PL PT RO SE SI Sk UK_ Lis u no ckj Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2014032601 Product s HBZ Super Cub SAFE RTF Item Number s HBZ8100EU HBZ8100EU1 HBZ8100UK HBZ8100UK1 Equipment class 2 The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE Directive 1999 5 EC EMC Directive 2004 108 EC and LVD Directive 2006 95 EC EN 300 328 1 7 1 2006 EN 301 489 1
31. the fuselage 6 Remove the hex nut L spacer M and front bearing N from the gear shaft 7 Remove the gear shaft and rear bearing 0 from the gearbox 8 Remove 2 screws P 2 rubber washers Q and the motor from the gearbox hobbyzane 14 Super Cub S EN Limited Warranty What this Warranty Covers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical regulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Re
32. y This model is controlled by a radio signal subject to interference from many sources outside your control Interference can cause momentary loss of control e Always operate your model in open spaces away from full size vehicles traffic and people e Always carefully follow the directions and warnings for this and any optional support equipment chargers rechargeable battery packs etc e Always keep all chemicals small parts and anything electrical out of the reach of children Charging Warnings CAUTION All instructions and warnings must be followed exactly Mishandling of Li Po batteries can result in a fire personal injury and or property damage By handling charging or using the included Li Po battery you assume all risks associated with lithium batteries H at any time the battery begins to balloon or swell discontinue use immediately If charging or discharging discontinue and disconnect Continuing to use charge or discharge a battery that is ballooning or swelling can result in fire Always store the battery at room temperature in a dry area for best results Always transport or temporarily store the battery in a temperature range of 40 120 F 5 49 C Do not store battery or aircraft in a Car or direct sunlight If stored in a hot car the battery can be damaged or even catch fire Always charge batteries away from flammable materials hobbyz ne e Always avoid water exposure to all equipment not spe
Download Pdf Manuals
Related Search