Catler CG 8010 coffee grinder
Contents
1. the bean hopper during operation Do not move the appliance if turned on Do not manipulate with the appliance if placed on the power base and turned on Do not put metal or similar items into the jug as this may damage or affect the operation of the unit Always ensure the START CANCEL button has been pressed to cancel before attempting to move the appliance when the appliance is not in use and before cleaning and storing The appliance is turned off if button illumination goes off Now you can unplug the appliance from the power outlet If you do not use the appliance for a long time or you attempt to leave unattended unplug the appliance from the power outlet Do not disconnect the appliance from the power point by pulling the electric cable it may damage the electric cable power point Use only supplied accessories or recom mended accessories by a manufacturer Otherwise it may result in fire electric shock or injury to persons Keep the appliance clean Refer to Care and Cleaning page 16 Disconnect the cable from the power point by gently pulling the plug of the electric cable WARNING DO NOT WASH THE POWER BASE UNDER RUNNING WATER e Do not operate the device for longer than 2 minutes as this could cause overheating Allow the Catler Coffee Grinder to cool down for 20 minutes after long operation WARNING TO PROTECT AGAINST ELECTRIC SHOCK DO NOT IMMERSE THE POWER BASE POWER CORD OR POWE2. grind pre ground coffee in bean hopper Under no circumstances should this product be used that is sticky or extremely hard or make pastes of any fruits seeds or herbs i e curry pastes nut batters Do not insert any metal objects or similar product into the bean hopper which could damage or negatively influence the device operation Do not place the appliance near the edge of a bench or table during operation Ensure that the surface is level clean and free of water Do not place the appliance on or near a hot gas burner electric element or where it could touch a heated oven Do not operate the appliance on a sink drain board Before you connect the appliance into the power outlet make sure the voltage on the rating label corresponds to the voltage in your power outlet Always ensure the appliance is properly assembled before connecting to a power outlet and operating Follow the instructions provided in this book Ensure the surface is level clean and free of water This appliance is not intended to be operated by means of an external timer or separate remote control system Before operation ensure the bean hopper lid is securely attached to the hoper The device should not be switched on until the bean hopper and hopper lid are locked into position in the grinding chamber Do not operate the device without locking the bean hopper lid in position Keep fingers hands hair clothing and utensils away from
3. lt 5 Clean lower burr Clean grind outlet Push upper burr Lock upper burr Align hopper into Lock hopper with cleaning brush with brush firmly into position position Problem Possible Cause What to Do Grinder does not start after Grinder not plugged in e Plug power cord into power outlet pressing START CANCEL Grinder is overheated e Remove power plug from power outlet Leave for 20 minutes to button cool down before using again Bean hopper not attached correctly e Lock bean hopper into position LOCK BEAN HOPPER will be displayed on LCD screen Motor starts but no ground Incorrect button press e Press START CANCEL or PORTAFILTER SWITCH to activate coffee coming from grind No coffee beans in bean hopper e Fill bean hopper with fresh coffee beans outlet Grinder bean hopper is blocked e Remove bean hopper Inspect bean hopper amp grind heads for blockage Replace parts and try again Motor starts but operates with Grinder is blocked with foreign item or Remove bean hopper inspect burrs amp remove any foreign body a loud racket noise chute is blocked e Clean burr heads and chute refer to Care amp Cleaning instructions Moisture clogging grinder e Leave burrs to dry thoroughly before re assembling It is possible to use a hair dryer to blow air into grinder inlet lower burr to dry Unable to lock bean hopper Coffee beans obstructing bean hopper Remove bean hopper Clear coffee beans from
4. top of burrs Re into position locking device lock bean hopper into position and try again Not enough too much coffee e Grind amount requires adjustment e Press AMOUNT button to change grind amount grind e Use ADJUST AMOUNT dial to fine tune the amount More or Less Portafilter overfills e Itis normal for the correct amount of coffee to appear overfilled in your portafilter Untamped coffee is three times the volume of tamped coffee Emergency stop e Press START CANCEL button to stop operation e Unplug power cord from power outlet INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Dispose of packaging material at a public waste disposal site DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES a The meaning of the symbol on the product its accessory or packaging indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may return your products to your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of waste Please ask your local authoritie
5. EE Catier COFFEE GRINDER Bj N SERIES PREMIUM GRADE 7 FOOLS Instructions for use CG 8010 COFFEE GRINDER CONTENTS Congratulations Catler recommends safety first Know your Coffee Grinder CG 8010 Assembling your Coffee Grinder CG 8010 Operating your Coffee Grinder CG 8010 Hints amp tips Care and Cleaning Troubleshooting CONTENTS E Er Ess o more o CUPS ADJUST AMOUNT AMOUNT START CANCEL on the purchase of your new Catler Coffee Grinder CG 8010 i CONGRATULATIONS We at Catler are very safety conscious We design and manufacture consumer products with the safety of you our valued customer foremost in mind In addition we ask that you exercise a degree of care when using any electrical appliance and adhere to the following precautions IMPORTANT SAFEGUARDS FOR YOUR COFFEE GRINDER CG 8010 Carefully read all instructions before operation and save for future reference Remove and safely discard any packaging material and promotional labels before using the appliance for the first time To eliminate a choking hazard for young children remove and safely discard the protective cover fitted to the power plug of this appliance This appliance has been designed specifically for the purpose of grinding roasted coffee beans only Under no circumstances should this product be used for other purposes than it is intended This appliance is not designed to
6. R PLUG IN WATER OR ALLOW MOISTURE TO COME IN CONTACT WITH THESE PARTS e Donot remove the jug from the power base during operation e The appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure they can use the appliance safely 6 CATLER RECOMMENDS SAFETY FIRST This appliance is for household use only Unwind the power cord fully before use Do not let the cord hang over the edge of a table or counter touch hot surfaces or become knotted This appliance is not intended for use by persons including children with reduces physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with this appliance It is recommended to inspect the appliance regularly Do not use the appliance if power supply cord plug or appliance becomes damaged in any way Return the entire appliance to the nearest authorised Catler Service Centre for examination and or repair Any maintenance other than cleaning should be performed at an authorised Catler Service Centre Do not use this appliance for other than its intended use Do not use in moving vehicles or boats Do not use outdoors IMPORTANT SAFEFUARDS FOR ALL ELECTRICAL APPLIANCES The
7. al 90 to lock into position Fill with coffee beans and place lid on top of bean hopper The bean hopper can be removed by turning knob anti clockwise and lifting upwards to pull bean hopper out The locking system allows you to remove and transfer hopper without having to remove the beans NOTE If Bean Hopper has not been locked into position LOCK BEAN HOPPER message will be displayed on the LCD screen disabling the operation of the grinder for safety OPERATING YOUR COFFEE GRINDER CG 8010 STEP 1 Selecting your Grind Size For each coffee style Espresso Percolator Filter and Plunger the grind size will differ Within each coffee style there is a range of settings Experiment with different grind settings to achieve the brew that best suits your taste EIIN AMOUNT START CANCEL Grinding for Espresso Coffee Machines If you are using Dual Wall Filters we suggest the coarser 11 20 setting For Single Wall Filters use the finer 17 25 setting in the ESPRESSO range PLUNGER FILTER PERCOLATOR ESPRESSO It tPirrrrrirdrdidridid COARSE LESS o MORE i NOTE If the grind dial is tight run grinder empty briefly by pressing the START CANCEL button whilst turning the dial STEP 2 Selecting your Grind Amount Select the desired amount of grinds required by pressing the AMOUNT button To increase keep pressing the AMOUNT button to the maximum number of shots or cups as shown in t
8. eat to protect the oils in the coffee bean Removable Upper Burr Lower Burr START CANCEL Button Starts amp stops operation Grind Size Dial 25 custom grind settings from espresso to plunger Brushed Stainless Steel Body Portafilter Activation Switch Accessories M Catches grind overspill cm Removable for easy cleaning if Conical Burr p Cleaning Brush Portafilter Cradle Container Cap NotShown 50 54mm Grinding Chamber Power Saving Sleep Mode Container Lid Slip Reducing Feet Minimises static of beans before Unit powers down to standby Portafilter Cradle dispensing after 5 minutes of non use 58mm Grinds Container For storing ground coffee Automatic Thermal Safety Cord Storage Shut Off Protects motor from overheating 8 KNOW YOUR COFFEE GRINDER CG 8010 Operating ASSEMBLING YOUR COFFEE GRINDER CG 8010 Before first use Before first use remove and safely discard all pro motional labels and packing materials attached to the device Wash hopper cradles grind container container lid and cleaning brush in warm soapy water and dry thoroughly Wipe exterior of grinder with a soft damp cloth and dry thoroughly Place grinder on flat level surface and plug power cord into 230 240V outlet and switch Power ON Eo ASSEMBLING YOUR COFFEE GRINDER CG 8010 Assembling the grinder Bean Hopper Align tabs and place bean hopper into position Turn the bean hopper di
9. he Coffee Chart below COFFEE TYPE PLUNGER MEDIUM INI DES 745 COARSE COARSE GRIND SETTING fez 3 5 1 UPTO 12 SHOTS 1 UPTO 12 SHOTS AMOUNT DRIP FILTER POE e E SHOTS m C hwo nf ly START CANCEL C ZA Vd The amount dispensed will vary depending on the grind setting The Catler Coffee Grinder will automatically adjust the dose for the grind se lected NOTE You can increase the amount already se lected during operation by pressing the AMOUNT button ESPRESSO DUAL WALL ESPRESSO PERCOLATOR SINGLE WALL MEDIUM FINE EXTRA FINE 6 10 11 20 17 25 1 UPTO 8 SHOTS 1 UPTO 8 SHOTS 1 UPTO 12 SHOTS OPERATING YOUR COFFEE GRINDER CG 8010 STEP 3 Using Auto or Manual Grinding Mode You can START and STOP the grinding operation in 2 ways 1 Automatic Grinding AUTO STOP e Press amp Release START CANCEL button or PORTAFILTER SWITCH once to activate Grinding will automatically stop when the selected grind amount is dispensed START CANCEL PORTAFILTER SWITCH PRESS amp RELEASE 2 Manual Grinding MANUAL START STOP e Press amp Hold either START CANCEL button or PORTAFILTER SWITCH for as long as you require Release START CANCEL button or PORTAFILTER SWITCH and the grinding will stop START CANCEL PORTAFILTER SWITCH PRESS HOLD amp RELEASE STEP 4 Grinding into your Portafilter Grind Container or Drip Fi
10. installation of a residual current device safety switch is recommended to provide additional safety protection when using electrical appliances It is advisable that a safety switch with a rated residual operating current not exceeding 30mA be installed in the electrical circuit supplying the appliance See your electrician for professional advice For the security reasons we recommend to plug the Catler Coffee Grinder directly to its own circuit separate from other appliances It is not recommended using hub or extension cord WARNING DO NOT OPERATE THE APPLIANCE ON AN INCLINED SURFACE DO NOT MOVE THE APPLIANCE WHILE IT IS SWITCHED ON WARNING ALWAYS ENSURE THE BEAN HOPPER IS INSERTED FIRMLY AND LOCKED PRO PERLY WARNING THE POWER PLUG WHEN PLUGGED MUST REMAIN ACCESSIBLE FOR EASY REMOVING SAVE THESE INSTRUCTIONS HOUSEHOLD USE ONLY CATLER RECOMMENDS SAFETY FIRST KNOW YOUR COFFEE GRINDER GG 8010 Bean Hopper Lid Air tight seal to maximise bean freshness Bean Hopper 450g bean hopper with locking system for easy removal and bean transfer Backlit LCD Screen Displays grind setting number of shots cups and customised amount ADJUST AMOUNT Dial Adjusts preset amount Less or More to suit personal taste AMOUNT Button Selects number of shots or cups Grind Outlet Grind Catch Tray Hardened Stainless Steel Conical Burrs Reduce grinding h
11. lter Basket 1 Grinding into Portafilter e Choose the cradle size that fits your portafilter either small 50 54mm or large 58mm e Slide cradle into position under grind outlet CRADLES e Insert portafilter into cradle e Use Automatic or Manual grinding function to start operation using the START CANCEL or PORTAFILTER SWITCH e Simply slide cradle out to remove 2 Grinding into Grind Container e Slide in grind container with cap open di rectly under grind outlet e Use Automatic or Manual grinding function to start operation using the START CANCEL button on the control panel You can grind into grind container without the lid However we recommend keeping the lid on to prevent coffee grinds from escaping OPEN CONTAINER CAP A INSERT UNDER GRIND OUTLET 3 Grinding into Drip Filter Basket e Place your drip filter basket under grind outlet e Use Automatic or Manual grinding function to start operation using the START CANCEL button on the control panel Customising your grind amount The ADJUST AMOUNT function gives you the ability to modify the preset amount to deliver more or less grinds into your portafilter or grind container Increasing the Grind Amount To increase the grind amount selected turn the ADJUST AMOUNT dial to the right Each bar adjustment will increase the grind amount by 5 up to a maximum of 25 more Decreasi
12. nd Cleaning CARE AND CLEANING 1 Make sure the device has been switched off by pressing START CANCEL button The device is switched off if push dial backlight has gone off Unplug the power cord from the power outlet before cleaning Wash the grind container and lid bean hopper and lid in warm soapy water rinse and dry thoroughly Wipe and polish exterior of appliance with a soft damp cloth NOTE Do do not use alkaline or abrasive cleaning agents steel wool or scouring pads as these can damage the surface NOTE We recommend you do not clean any grinder parts or accessories in the dishwasher CARE AND CLEANING WARNING NEVER IMMERSE THE POWER BASE POWER CORD AND PLUG IN WATER OR ANY OTHER LIGUID DO NOT EXPOSE THE DEVICE OR ANY ITS PART TO MOISTURE NOTE USE A SOFT CLOTH AND MILD DETERGENT TO CLEAN THE APPLIANCE Storage 1 Ensure the appliance is switched off cleaned and dried before storing Ensure all accessories are clean and dry Wrap the power cord around the power cord storage under the power base Store the appliance upright position Do not place anything on top Cleaning conical burrs Regular cleaning helps the burrs achieve consistent grinding results which is especially important when grinding for espresso coffee Unlock hopper Remove beans Lock hopper Run grinder until Remove hopper Remove upper burr Clean upper burr empty with cleaning brush
13. ng the Grind Amount To decrease grind amount selected turn the ADJUST AMOUNT dial to the left Each bar adjustment will decrease the grind amount by 5 up to a minimum of 25 less ESPRESSO NE s FI AMOUNT START CANCEL Energy Saving Feature The grinder will automatically switch off if not used after 5 minutes To reactivate the machine whilst in POWER SAVING SLEEP MODE press any button on the grinder control panel These hints and tips will help you to improve the results of grinding coffee and preparation of your favorite beverages Fresh grinds are the key to making coffee with more flavour and body Coffee flavour and strength is a personal preference Vary the type of coffee beans amount of coffee and fineness of grind to achieve the flavour you prefer Use freshly roasted coffee beans preferably with a roasted on date Store coffee beans in a dark cool and dry place Vacuum seal if possible Buy in small batches to reduce the storage time and store no more than one week s supply at any time Once coffee is ground it quickly loses its flavour and aroma For the best results grind beans immediately before brewing Do not store beans in the bean hopper for a prolonged period When storing appliance run grinder empty to clear of ground beans left in chamber Run grinder for 2 seconds before each use for maximum freshness Clean the bean hopper and conical burrs regularly Care a
14. s or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union If you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union If you wish to dispose of this product request the necessary information about the correct disposal method from local government departments or from your seller This product meets all the basic EU regulation requirements that relate to it Changes to the text design and technical specifications may occur without prior notice and we reserve the right to make these changes bs cauer COFFEE GRINDER c SERIES PREMIUM GRADE TOOLS Due to continued product improvement the products illustrated photographed in this brochure may vary slight ly from the actual product WWW CATLER EVU CUSTOMER SERVICE INFO CATLER EU
Download Pdf Manuals
Related Search