Home
Rode PinMic
Contents
1. lt gt ABOVE CLOTHING BACKPLATE a UNDERNEATH CLOTHING Bring the backplate up underneath the user s clothing then press the pins through to the other side of the fabric The standard 5 backplate pins are able to comfortably pin through clothing up to approximately 1 5mm thick 0 006 0 14 The heavy duty model is recommended for fabric from around 1 5mm up to 3 5mm 0 006 0 14 thick Sd FITTING YOUR PINMIC Once the pins are exposed simply match the receptacles on the PinMic to the pins on the backplate and press on After the click the PinMic will be securely fastened There is no need to push the microphone down further PinMicTM ABOVE CLOTHING BACKPLATE 7 UNDERNEATH CLOTHING Match the backplate pins to the PinMicTM receptacles 11 FITTING YOUR PINMIC To prevent tangling you may utilise the provided cable management clip Clip the cable into the groove on the lapel clip then loop through as many times as necessary and attach to clothing gt E MN Clip the cable into the groove on your lapel clip 2122 FITTING YOUR PINMIC To connect your PinMicTM to your wireless system securely fasten the corresponding adaptor to the end of your MiCon cable MiCon CONNECTION DIE 1 1 1 1 1 MiCon CABLE 1 MiCon ADAPTOR R DE MiCon cable an
2. FICATIONS FREQUENCY RANGE dB re 1 V Pa ESI 20Hz 100 1000 10000 20000 POLAR RESPONSE Laso 90 Frequency 500 Hz mm 1000 Hz mm 4000 Hz mm Calculated from maximum SPL peak before clipping All measurements are calculated when powered at 5 V or P48 RODE XLR adaptor 7 PINMIC STRUCTURE PINMICTM ASSEMBLY RECEPTACLES den Kevlar amp REINFORCED CABLE MiCon CONNECTION PINMIC CAPSULE MESH HEAD EL MESH HEAD GROOVE CAPSULE CAP PinMic CAPSULE MIC PLACEMENT For the best performance the PinMic should be positioned as close as possible to the sound source without being subject to clothing rustle gusts of air or dust F we a Position the microphone close to the sound source At times it may be best to test different placements to provide the optimal combination of sound quality and discretion FITTING YOUR PINMIC To fit your PinMic and connect to your wireless system first pin the backplate of the microphone to your clothing close o the sound source You may do this by weaving the backplate and cable up from underneath the user s clothing or placing it just behind the apel on a jacket Ensure the backplate is hidden underneath he fabric then press through until the pins are exposed on he other side PinMic
3. PINMIC INSTRUCTION MANUAL MICROPHONES www rodemic com INTRODUCTION Thank you for investing in the RODE PinMic Whether you re presenting for television or live on stage in a 20 000 seat auditorium or in a house of worship RODE has your needs covered with the intuitive and subtle PinMic Featuring innovative industry leading design the RODE PinMic is the first of its kind The pin on placement of the microphone provides an ultra discreet appearance while also simplifying cable management The included mini furry for high wind protection ensures quality recordings in adverse environments while the anti trauma water resistant case provides rugged and secure protection for the microphone cable and accessories Knowing that versatility is paramount in any product we at RODE have developed the MiCon connector system which provides seamless integration between the and a wide range of wireless systems Please take the time to visit www rodemic com and register your microphone for warranty ES Peter Freedman RODE Microphones Sydney Australia FEATURES INTUITIVE AND SUBTLE Ultra discreet appearance Lightweight and easy to position Pins through clothing up to approximately 1 5mm 0 006 thick standard model or approximately 1 5 3 5mm 0 006 0 14 thick heavy duty model Removable mesh head HIGH QUALITY PERFORMANCE Low noise miniature microphone
4. capsule Low handling noise UNIVERSAL COMPATIBILITY R DE MiCon connector system provides seamless integration with a wide range of wireless systems while maintaining discreet and unobtrusive appearance PI NMIC amp ACCESSORIES RODE PinMic ementary mesh head silver suitable for spray paint customisation to fully match clothing Anti trauma water resistant storage case urry for high wind protection Shielded Kevlar reinforced cable with moulded backplate 1 2 Supp 3 4 Mini 5 6 Lape style cable management clip 7 Adjustment tools 8 Sanitary cleansing wipes Compac interchangeable MiCon adaptors available to suit industry standard wireless systems MiCon a see rodemi daptors sold separately c com pinmic for a full list of compatibility SPECIFICATIONS Acoustic Principle Directional Pattern Frequency Range Output Impedence Signal To Noise Ratio Equivalent Noise Clipping SPL Maximum Output Sensitivity Dynamic Range Power Requirements Output Connection Permanently polarised condenser Omni directional see graph 60 Hz 18 kHz see graph 3k Q Typical 69 dBA 25 dBA SPL per IEC651 110 dB 189 mV 33 5 dB re 1 V Pa 21 mV 94 dB SPL 3 dB 1 kHz 85 dB Typical Min 2 V Max 5 V through RODE wireless adaptors P48 through R DE XLR adaptor R DE MiCon connector SPECI
5. d adaptor The PinMic s connections have been designed using the R DE MiCon connector system which provides seamless integration with a wide range of wireless systems while maintaining the mic s discreet appearance MiCon adaptors sold separately see rodemic com pinmic for a full list of compatibility Plug the adaptor into your wireless system and you re ready to go S3 INCLUDED ACCESSORIES SUPPLEMENTARY MESH HEAD For instances in which the PinMicTM user is wearing a light coloured garment RODE have provided a supplementary silver mesh head This will maintain the PinMic V s subtle appearance on the clothing To switch from your pre fitted black mesh head to the silver first disassemble your PinMic with your RODE adjustment tool This is best done over a desk or work surface to ensure no parts are misplaced Pull apart the two sections of the adjustment tool to reveal the driver and socket sections Place your PinMic in the socket hole mesh down so that the bottom of the microphone is visible Match the flat edges of the mesh head to the flat edges of the socket hole to insert correctly Then use the groove across the bottom of the mic to unscrew the mic capsule from the mesh head 2 PinMic gt PL S A gt NUI 6 7 227 WE p SS KL ex A b ADJUSTMENT TOOL V Pk Ny SOCKET N ADJUSTMENT TOOL DRIVER Place microphone in the adjustment tool sock
6. et mesh down 14 INCLUDED ACCESSORIES Use the groove across the bottom of the mic to unscrew Once the microphone capsule is loose remove it from the mesh Remove the black mesh head from the socket using the groove on the mesh ring as grip Next insert the silver mesh head into the socket Place the microphone capsule into the silver mesh and tighten on securely with the driver SUPPLEMENTARY 2 7 SILVER MESH SOCKET HOLE PinMicTM CAPSULE Place the silver mesh in the socket then the mic capsule then tighten Note Please do not attempt to screw the mesh head onto the PinMicTM by tightening while the microphone is attached to the backplate This may cause damage to the backplate pins Always remove your microphone from clothing and backplate before changing mesh heads 15 INCLUDED ACCESSORIES CUSTOMISING THE SILVER MESH HEAD The supplementary silver mesh head can be custom painted to match the colour of the user s clothing providing an even higher level of microphone camouflage To colour your mesh first use a pair of tweezers to remove the inner foam pop filter from just under the mesh head This foam reduces wind noise and moisture reaching the microphone capsule and must not be exposed to paint Once the foam is removed use a spray paint in the colour of your choice to paint the mesh Spray from a distance applying a thin even coat over the surface A
7. k in colour They can easily be re used by placing them in an oven at 100 150 degrees Celsius for approximately ten minutes The crystals will operate effectively again once they have turned blue In some cases such as when there are multiple users of the PinMic you may wish to sanitise the backplate and cable To do this use the provided Sanitary Cleansing Wipes to wipe down the PinMic surface You may wish to detach the microphone from the backplate and cable for easier access Please be mindful when cleaning the PinMic not to let any dust or moisture into the microphone capsule 18 SUPPORT If you experience any problem or have questions regarding your microphone first contact the dealer who sold it to you We have an extensive dealer network to assist you If you have difficulty getting the advice or assistance you require from the dealer do not hesitate to contact us directly via the details below RODE MICROPHONES INTERNATIONAL 107 Carnarvon Street Silverwater NSW 2128 Australia Ph 61 29648 5855 Fax 61 29648 2455 USA P O Box 4189 Santa Barbara CA 93140 4189 Ph 805 566 7777 Fax 805 566 0071 TECHNICAL SUPPORT For information and technical support please visit www rodemic com support 19 c Ee
8. llow the mesh to dry completely before its next usage Once dry return the inner foam to its place inside the mesh Follow the instructions on pages 14 15 to switch the mesh heads on the PinMic Always keep your unused mesh head in the provided storage case for complete protection Note When colouring please be cautious not to block any of the holes in the mesh head This may reduce the acoustic transparency of the PinMic resulting in compromised audio quality To check that the mesh head is clear hold it up against a light and ensure the light filters through the holes 16 INCLUDED ACCESSORIES MINI FURRY For increased wind protection a mini furry windshield is provided with the PinMic The windshield is ideal for situations such as outdoor performances where wind noise may distort the audio quality of the mic To fit simply press on the mini furry straight over the PinMic until it is secured by the groove on the mesh head PinMic with mini furry 17 STORAGE amp CARE When not in use always keep your PinMicTM in the storage case provided Close and snap the storage case for complete protection Inside the case you will find a sachet of moisture absorbent crystals Please retain these crystals and store with the PinMic to keep the microphone in ideal condition Eventually this pack of crystals will need to be dried This is indicated by the crystals turning pin
Download Pdf Manuals
Related Search
Related Contents
PN 97385 2D Position-Sensitive Neutron Detector - DENEX-GmbH Bedienungsanleitung Monster Cable THX SL200-CTR User's Manual intext:installationshandbuch filetype:pdf Speed-Distance 200 Copyright © All rights reserved.
Failed to retrieve file