Rode HS1-B microphone
Contents
1. 100 Frequency 500 Hz mm 1000 Hz zx 4000 Hz mm 1000 10000 20000 Calculated from maximum SPL peak before clipping All measurements are calculated when powered at 5V or P48 RODE XLR adaptor A HS1 STRUCTURE CABLE CONTROL TAB MiCon i CONNECTION l T HEADBAND 1 RETAINER i MOISTURE CONTROL BELT MICROPHONE WITH POP FILTER AA N EAR HOOK RETAINER CAP Zt HEADBAND SIZE ADJUSTMENT TAB MIC PLACEMENT For the best performance the HS1 microphone should be positioned just at the corner of the mouth as close as possible without being in front of the user s mouth This ensures that the mic is in close proximity to the sound source without being exposed to possible plosives gusts of wind noise caused by hard sounds such as p or 47 29 FITTING YOUR HS1 The RODE HS1 has been designed with complete adjustability in mind ensuring maximum comfort and security of fit for each user Three axes of movement configure the microphone placement for optimal audio quality To custom fit the HS1 you may wish to try on the microphone first Hook the headband over your ears and the size of the headband can be controlled by pushing or pulling the left and right tabs along the rear of the headset HEADBAND SIZE ADJUSTMENT TAB Ww v E ee ae Om M 235 gt E a N OS Once2. furry 19 STORAGE AND CARE When not in use always keep your HS1 in the storage case provided Close and snap the storage case for complete protection If you find you cannot open the case even after snapping open the clips for example following a flight turn the dial at the front of the case slowly in the direction marked open This will equalise the air pressure in the case and allow it to open i20 STORAGE AND CARE Inside the case you will find a sachet of moisture absorbent crystals Please retain these crystals and store with the HS1 to keep the microphone in ideal condition Eventually this pack of crystals will need to be dried This is indicated by the crystals turning pink in colour They can easily be re used by placing them in an oven at 100 150 degrees Celsius for approximately ten minutes The crystals will operate effectively again once they have turned blue In some cases such as when there are multiple users of the HS1 you may wish to sanitise the microphone To do this use the provided Sanitary Cleansing Wipes to wipe down the HS1 surface You may wish to detach the microphone from the headband wire for easier access Please be mindful when cleaning the HS1 not to let any dust or moisture into the microphone capsule 21 SUPPORT If you experience any problem or have questions regarding your microphone first contact the dealer who sold it to you We have a
3. HS1 INSTRUCTION MANUAL MICROPHONES www rodemic com INTRODUCTION Thank you for investing in the RODE HS1 Headset microphone Whether you re presenting for television or live on stage in a 20 000 seat auditorium or in a house of worship RODE has your needs covered with the reliable and intuitive HS1 Featuring the pure clear audio and low handling noise that RODE is celebrated for the HS1 Headset is built to deliver and to last Subtle ergonomic design including three axes of mechanical adjustment malleable tube arm and ultra lightweight headband ensure the perfect fit for each individual Knowing that versatility is paramount in any product we at RODE have developed the MiCon connector system which provides seamless integration between the HS1 Headset and a wide range of wireless systems Please take the time to visit www rodemic com and register your microphone for warranty Cline Peter Freedman R DE Microphones Sydney Australia FEATURES ERGONOMIC DESIGN e Ultra discreet appearance e Three axes of mechanical adjustment for perfect fit e Malleable tube arm and headband for fine adjustment e Ultra lightweight construction for complete comfort Rightor left side configuration Incorporated cable management system HIGH QUALITY PERFORMANCE 234 mm 0 144 miniature microphone Corrosion resistant stainless steel tube arm Incorporated moisture control belt to minimise swe
4. at contacting the capsule Low handling noise UNIVERSAL COMPATIBILITY R DE MiCon connector system provides seamless integration with a wide range of wireless systems while maintaining discreet and unobtrusive appearance e Gold plated connections HS1 amp ACCESSORIES RODE HS1 Headset Anti trauma water resistant storage case Water resistant pop filter Mini furry for high wind protection Shielded detachable Kevlar reinforced cable Lapel style cable management clip Adjustment tools Sanitary cleansing wipes COE 0 a Compact interchangeable MiCon adaptors available to suit industry standard wireless systems 7 MiCon adaptors sold separately see rodemic com hs1 for a full list of compatibility EA SPECIFICATIONS Acoustic Principle Directional Pattern Frequency Range Output Impedence Signal To Noise Ratio Equivalent Noise Clipping SPL Maximum Output Sensitivity Dynamic Range Power Requirements Output Connection Permanently polarised condenser Omni directional see graph 60 Hz 18 KHz see graph 3k Typical 58 dBA 36 dBA SPL per IEC651 122 dB 189 mV 47 2 dB re 1 V Pa 21mV Q 94 dB SPL 3 dB 1 kHz 86 dB Typical Min 2V Max 5V through RODE wireless adaptors P48 through RODE XLR adaptor R DE MiCon connector SPECIFICATIONS FREQUENCY RANGE dB re 1 V Pa POLAR RESPONSE 30 20Hz
5. from the retainer clasp The push pull motion is controlled by friction so apply a little force if required If necessary twist the microphone body back and forth while pushing pulling to encourage the mic body through the retainer and create the desired length When adjustment has been completed tighten the retainer cap securely into place Push or pull the body of the HS1 through the retainer clasp using a twisting motion 213 FITTING YOUR HS1 LEFT RIGHT CONFIGURATION OF HS1 Depending on personal preference the HS1 can sit at either the left or right hand side of the mouth To change left right configuration unscrew the retainer cap completely using the screwdriver provided This is best done over a table or work surface to ensure no parts are misplaced Ease the microphone to the left and right until it releases from the headband wire completely HEADBAND WIRE RETAINER CAP Completely unscrew the retainer cap On the opposite side of the headband snap the microphone into place matching the curves of the inside of the retainer to the shape of the headband wire Return the retainer cap and screw back into place 14 FITTING YOUR HS1 m RETAINER CAP Re position the HS1 then screw the retainer cap back into place ERGONOMIC ADJUSTMENT For further ergonomic adjustment you may bend the microphone
6. n extensive dealer network to assist you If you have difficulty getting the advice or assistance you require from the dealer do not hesitate to contact us directly via the details below RODE MICROPHONES INTERNATIONAL 107 Carnarvon Street Silverwater NSW 2128 Australia Ph 61 2 9648 5855 Fax 61 2 9648 2455 USA P O Box 4189 Santa Barbara CA 93140 4189 Ph 805 566 7777 Fax 805 566 0071 TECHNICAL SUPPORT For information and technical support please visit www rodemic com support 229 ce E e
7. or further management excess cable can be threaded through the groove in the cable management clip provided Loop through the peg as many times as necessary and peg to the user s clothing MiCon CONNECTION E MiCon CABLE i ADAPTOR R DE MiCon cable and adaptor 17 INCLUDED ACCESSORIES WATER RESISTANT POP FILTER The pop filter is an optional attachment to your HS 1 which reduces plosives gusts of wind noise caused by hard sounds such as p or t It is also strongly recommended you use your pop filter to protect the HS1 in any extreme environments which are overly dusty or moist to prevent damage to the mic To correctly fit your pop filter slide the filter over the microphone head until it reaches the first groove Pushing the fi ter any further down will result in decreased protection of the capsule rt Mic with no wind protection Mic with pop filter 18 INCLUDED ACCESSORIES MINI FURRY For increased wind protection a mini furry windshield is provided with the HS1 The windshield is ideal for situations such as outdoor performances where wind noise may distort the audio quality of the mic To fit simply slide the mini furry over the microphone head until it reaches the first groove Ensure the fur is fluffed up in all directions for maximum effectiveness Mic with mini
8. the current fit is assessed make any of the following alterations to the microphone as necessary 10 FITTING YOUR HS1 ADJUST THE HEIGHT OF THE HS1 To place the retainer at the ideal position just below and behind the ear lobe change the position of the retainer on the headband wire To re position loosen the retainer cap using the screwdriver provided in your HS1 case You will not need to unscrew the retainer cap completely to allow movement Once satisfied with the height of the retainer on the headband tighten the retainer cap back in place NA E RETAINER CAP X N Loosening the retainer cap with provided R DE screwdriver FITTING YOUR HS1 PIVOT THE HS1 You may adjust the proximity of the microphone to your mouth by pivoting the mic Push the microphone up or down at the retainer to create a rotating movement until you find the angle that positions the HS1 microphone closest to your mouth 300 degrees of rotation allows for the best possible positioning Pivot the HS1 in a rotating movement Diz FITTING YOUR HS1 ADJUST THE LENGTH OF THE HS1 If the HS1 is extending beyond your mouth or is not in close enough proximity to it you may alter the length by pushing or pulling the body through the retainer Firstly ensure the retainer cap has been loosened but not removed completely Hold the mic body at the connector end and twist 90 1 4 turn to unlock it
9. tube along the body and adapt its shape This allows the microphone to suit the contours of an individual face for complete compatibility with the wearer Note The HS1 tube arm is designed to be resilient and malleable for optimal adjustment However it is not recommended that the microphone tube be bent using sharp objects or at extreme angles A smooth repetitive bend using the tips of your fingers to coax the frame will be sufficient in contouring the microphone to your face 15 CONNECTOR AND CABLE The HS1 s connections have been designed using the RODE MiCon connector system which provides seamless integration with a wide range of wireless systems for your convenience while maintaining the headset s discreet appearance MiCon adaptors sold separately see rodemic com hs1 for a full list of compatibility To connect the HS1 to your MiCon cable screw either end of the cable to the MiCon connection at the end of the microphone tube To prevent tangling clip the cable into the groove in the cable control tab at the back of the headband CABLE CONTROL TAB 4 V V 2 Prevent tangling by clipping the cable into your cable control tab CONNECTOR AND CABLE Then attach the corresponding adaptor for your wireless system to the remaining connection on your MiCon cable and plug in to your wireless system MiCon adaptors sold separately F
Download Pdf Manuals
Related Search