Dimplex DF2608 fireplace
Contents
1. tinuously reset the heater un plug the unit and call Technical Support at 1 888 346 7539 Please have your model and serial number ready when call ing Remote Control Figure 6 The fireplace is supplied with an integrated on off remote control NOTE Ensure that the 3 Position Switch on the fireplace is set to the remote control setting Il posi tion To operate push the ON button to turn the fireplace on push the OFF button to turn the fireplace off NOTE Before attempting any operation with the remote pull the plastic insulator strip out from between the remote cas ing and battery cover Figure 6 Figure 6 On Button Off Button a Plastic strip Battery cover www dimplex com Operation Remote Control Initialization Reprogramming Follow these steps for remote control initialization and if re quired re initialization 1 Disconnect power to fire place 2 Setthe 3 Position Switch to the Remote position Figure 5A 3 Wait a minimum of five seconds and then re acquire power to fireplace 4 Within 10 seconds of re ac quiring power press the ON button located on the remote control NOTE You will have only 10 seconds to perform this last step Failure to do so will result in these steps needing to be followed again This will synchronize the remote control and receiver Battery Replacement Figure 62. abnormal conditions Do not partially or fully cover or ob struct the front of this heater Wiring POSITION SWITCH RECEIVER cep peo REMOTE i i i m L oi L 0d i l MANUAL HEATER ON OFF CUT OUT HLT ELEMENTS L THERMOSTAT HT BLOWER MOTOR M LOG DRIVER LED LOGS LOWER LIGHTS UPPER LIGHTS DIMMER l SPEED CONTROL M FLICKER MOTOR 10 www dimplex com Operation Figure 5 A B C E D h E 6c wt B WARNING This electric firebox must be properly installed before it is used Manual Controls The manual controls for the fireplace are behind the access panel located at the bottom of the fireplace Figure 5 A 3 Position Switch The switch has two On positions marked with I and Il The I position is for manual operation In this position the built in remote control is bypassed The II position is for operating the unit with the provided remote control When in II position the unit is operated with the ON and OFF buttons of the remote control When the switch is in the center O position the unit is off B Flame Action Control Turn the Flame Action Control knob to adjust the flame speed to the desired level C Light Dimmer Control v Turn the Light Dimmer Control knob to increase or decrease the brightness o
3. an outlet near 4 the fireplace Option 2 A new outlet can be installed inside the framing con struction A 120 V outlet NOTE A 15 Amp 120 Volt circuit is required A dedicated circuit is preferred but not essential in all cases A dedi cated circuit will be required if after installation the circuit breaker trips or fuse blows on a regular basis when the heater is operating Additional appliances on the same circuit may exceed the current rating of the circuit breaker Existing Fireplace Seal all drafts and vents with a non fibrous insulation mate rial to prevent any chimney debris from falling onto the fireplace Do not install into an existing fireplace that is prone to dampness Cap the top of the chimney flue to prevent rain from entering Plan your electric power sup ply The power cord can run along the front of the hearth to an outlet near the fireplace For Bathroom Use If this unit is installed in a bath Fireplace Installation room it must be protected by a GFI receptacle or circuit If re ceptacle is used it must be readily accessible To prevent electrical shock this unit is an electrical appliance that is not watertight and must be installed as to prevent water from entering unit This must be in stalled away from showers tubs etc Never locate fireplace where it may fall into a bathtub or other water container High tempera tures may be generated under certain
4. 280007 1100RP Heat On Off Switch e see mmm 2800070700RP Flame Action Control with Potentiometer 3000240500RP Light Dimmer Control with Potentiometer 3000250100RP CORD SeT orire a ee pests puss e EMEN IRR BUE 4100040500RP Single Lamp Holder Center Lower 2500150300RP Double Lamp Holder Upper and Lower 2500400300RP Partially Reflective Glass llle 5901210200RP Front Glass score aie Sea serra pa hdc ad a e d P EO eol 5901220100RP Gontrol Knobs sse yam ES nae g katt BOR RUE BEES 8800000200RP Remote Control se exo eue En E aku Ea E a ROS ax ena 3000370500RP Remote Control Reciever lllllls illus 3000380200RP Flicker ROG 1 et xo sore Se Ea era e 5901250100RP Trim Replacement Kit DF2608 NBDF2608 9600260100RP XC Dimplex O Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 2013 Dimplex North America Limited 20 www dimplex com
5. Insert new bulbs and screw in 3 Remove three Phillips screws clockwise from right side of trim 10 Re attach light block bracket 4 Remove trim 11 Lay unit on it s back slide front glass back into position 5 Slide glass to the right side and attach trim of the fireplace to remove Figure 7 Figures Light Block screws 4 Light Block Flicker Rod Light Filter Bracket screws 2 Lower Light Bulbs 3 16 www dimplex com I Maintenance Glass Cleaning The glass is cleaned in the factory during the assembly operation During shipment installation handling etc the clear door may collect dust particles these can be removed by dusting lightly with a clean dry cloth O Warranty Two Year Limited Warranty Products to which this limited warranty applies This limited warranty applies to your newly purchased Dimplex electric fireplace This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory Nunavut or Northwest Territories or in any of the 50 States of the USA and the District of Columbia except for Hawaii and Alaska This limited war ranty applies to the original purchaser of the product only and is not transferable Products excluded from this limited war ranty Light bulbs are not covered by this limited warranty and are the sole responsibility of the owner purchaser Products purchased in Yukon Territory Nunavut N
6. RECT SPECIAL PUNITIVE EXEMPLARY CONSEQUEN TIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAIN TENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL DIMPLEX OR ITS OFFICERS DIREC TORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PUR CHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IN CIDENTAL OR CONSEQUENTIAL DAM AGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER How State and Provincial law apply This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to juris diction The provisions of the United Na tions Convention on Contracts for the Sale of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty 19 Pd Replacement Parts LED Log Set DF2608 NBDF2608 0439560100RP Log Set DF2622 iste Rr ideti TERRE 0439560200RP Flicker MtO uii ear Een aera py Fac are cecus 3000240200KIT Heater Assembly with Cutout 0000 2000330100RP Thermostat aces keeeaup eed mates munt dens E REOR Shee 2300150100RP S POSIION SWICK a Bawa ees DR e RR ER eeu
7. To replace the battery Slide battery cover open on the remote control Correctly install one 12 Volt A23 battery in the battery holder Close the battery cover Battery must be recycled Epo disposed of properly Check with your Local Authority or Retailer for recycling advice in your area I Maintenance WARNING Disconnect power before attempting any main tenance or cleaning to reduce the risk of fire electric shock or damage to persons NOTE The fireplace should not be operated with an accumu lation of dust or dirt on or in the unit as this can cause a build up of heat and eventual damage For this reason the heater must be inspected regularly depending upon conditions and at least at yearly intervals Light Bulb Replacement The light bulbs need to be re placed when you notice a dark section of the flame or when the clarity and detail of the log em ber bed exterior reduces There are three bulbs under the Log Set Assembly which generate the flames and embers and two bulbs above that illuminate the log exterior Lower Light Bulb Requirements Quantity of three clear chande lier or candelabra bulbs with an E 12 small socket base 60 Watt rating Example GE 60BC or Philips GOCTC Do not exceed 60 Watts per bulb Helpful Hints It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life Group replacement will reduce the number of
8. X Dimplex Better solutions through innovation Owner s Manual Model DF2608 NBDF2608 DF2622 IMPORTANT SAFETY INFORMATION Always read this manual first before attempting to install or use this fireplace For your safety always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage To view the full line of Dimplex products please visit www dimplex com 7208680100R07 Table of Contents Welcome amp Congratulations 3 A IMPORTANT INSTRUCTIONS 4 S Fireplace Installation 222 2 RRX PURO 7 qu Operation uua uu ate eoe ace Rip ES o aes 11 P Maintenance 1222 das px REA REOR E dope 3 14 D Wamanty nea du eaan aiaa AREE ERD 17 Replacement 3 c 20 Always use a qualified technician NOTE Procedures and or service agency to repair techniques that are considered this fireplace important enough to emphasize amp CAUTION Procedures and techniques which if not carefully followed will result in damage to the equipment WARNING Procedures and techniques which if not carefully followed will expose the user to the risk of fire serious injury or death 2 www dimplex com D Welcome amp Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex the world leader in electric fireplaces Please carefully read and save these instructions a
9. arranty services Accord ingly Dimplex will be responsible for all labour and transportation costs associ ated with the repair or replacement of the product or part except as follows i charges may be levied for travel costs incurred to travel to the purchaser s site where the product is located if the purchaser s site is beyond 30 miles 48 km from the closest service depot of Dimplex s dealer or service agent and ii the purchaser is solely responsible for providing clear access to all service able parts of the product For products other than surrounds mantels and trims for the period commencing at 12 01 a m on the day after the first anniversary of the first purchase and ending at mid night on the second anniversary of the date of first purchase this limited warranty entitles the purchaser to re placement parts only without charge If Dimplex is unable to replace such part or if replacement is not commercially practicable or cannot be timely made 18 www dimplex com O Warranty Dimplex may in lieu of replacement choose to refund the purchase price for such part The purchaser shall not be entitled to on site or in home war ranty services The purchaser shall be responsible for all expenses incurred for the removal of the part and installa tion of the replacement part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s
10. ces for the 1 year period commencing on the first anniversary of first purchase and ending on the second anniversary of the date of first purchase Dimplex fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to ship ment and subject to the provisions of this warranty Dimplex warrants such products 17 OG Warranty to be free from defects in material and workmanship for a period of 1 year from the date of first purchase of such products Warranty services do not include in home services The limited 2 year warranty period for products other than fireplace surrounds mantels and trims and the limited 1 year warranty period for fireplace surrounds mantels and trims also applies to any implied warranties that may exist under applicable law Some jurisdictions do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to the purchaser What this limited warranty does not cover This limited warranty does not apply to products that have been repaired except by Dimplex or its authorized service rep resentatives or otherwise altered This limited warranty does further not apply to defects resulting from misuse abuse accident neglect incorrect installation im proper maintenance or handling or opera tion with an incorrect power source What you must do to get service under this limited warranty Defects must be br
11. e 11 Insert new bulbs and screw in clockwise 12 Replace light filter bracket Figure 8 Log Ember Bed Back Ledge Rear Tab Side Section Front Edge and flicker rod 13 Install the log set assembly by placing the front bottom edge of the ember bed in the track behind the control panel Once in place push down on the back edge of the ember bed until the rear tab snaps into place under the partially reflective glass Figure 8 NOTE Ensure the log set Assembly is installed tightly under the bottom edge of the partially reflective glass to prevent light leakage 14 Lay unit on it s back and slide Front Glass back into position and attach trim Upper Light Bulb Requirements Quantity of two clear chandelier or candelabra bulbs with an E 12 small socket base 15 Watt rat 15 I Maintenance ing Do not exceed 25 Watts per 6 Upper bulbs are located in bulb the upper left and upper right To access the upper light bulb corners of fireplace behind area the light block bracket Figure 9 amp CAUTION Allow at least five minutes for the light bulbs to cool 7 Remove the four Phillips before touching them to avoid ac screws that attach the light cidental burning of the skin block to the firebox Figure 9 1 Slide fireplace out of mantel 8 Unscrew bulbs counter clock 2 Layunit on it s back for safe Wee removal of front glass 9
12. en or invalids and whenever the unit is left operating and unattended Always unplug the electric fireplace when not in use Do not operate any heater after it malfunctions Disconnect power at the service panel and have the heater inspected by a reputable electrician before reus ing 6 Do not operate any unit with a damaged cord or plug or if the heater has malfunctioned or if the electric fireplace has been dropped or damaged in any man ner contact Dimplex Technical Service at 1 888 346 7539 Do not use outdoors Never locate heater where it may fall into a bathtub or other water container Do not run the cord under carpeting Do not cover cord with throw rugs runners or the like Arrange cord away from traf fic area and where it will not be tripped over To disconnect the unit turn the controls off then remove the plug from the outlet Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage to the heater 2 To prevent a possible fire do not block air intake or exhaust in any manner 3 All electrical heaters have hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored Do not modify the electric fireplace Use it only as described in this manual Any other use not www dimplex com amp IMPORTANT INSTRUCTIONS recomm
13. ended by the manufactur er may cause fire electric shock or injury to persons 5 Always plug heaters directly into a wall outlet receptacle Never use with an extension cord or relocatable power tap outlet power strip Do not burn wood or other materials in the electric fireplace Do not strike the fireplace glass Always use a certified electri cian should new circuits or outlets be required Always use properly ground ed fused and polarized outlets Disconnect all power supply before performing any cleaning maintenance or relocation of the unit When transporting or storing the unit and cord keep in a dry place free from excessive vibra tion and store so as to avoid dam age amp WARNING Remote control contains small batteries Keep away from children If swallowed seek medical attention immedi ately amp WARNING Do not install bat tery backwards charge put in fire or mix with used or other battery types may explode or leak caus ing injury NOTE Changes or modifica tions not expressly approved by the party responsible for compli ance could void user s authority to operate the equipment CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NO USER SERVICABLE PARTS INSIDE SAVE THESE INSTRUCTIONS amp IMPORTANT INSTRUCTIONS NOTE This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These
14. f the interior of the fireplace D Heater On Off Switch The Heater On Off Switch sup plies power to the heating unit when the 3 Position Switch A is on I or Il positions NOTE The heater on your fireplace may emit a slight harmless odor when first used This odor is a normal condition caused by the initial heating of internal heater parts and will not occur again E Heater Thermostat Control i To adjust the temperature to your individual requirements turn the thermostat control clockwise all the way to turn on the heater When the room reaches the de 11 Operation sired temperature turn the ther mostat knob counter clockwise until you hear a click Leave in this position to maintain the room temperature at its setting For additional heat turn clockwise until you hear the click again and the heater will turn on To turn the heater off rotate the knob fully counter clockwise Resetting the Temperature Cutoff Switch This unit is equipped with a ther mostat which controls the tem perature of the room by turning the heater on and off The heater is protected with a safety device to prevent overheating Should the heater overheat an automatic cut out will turn the heater off and it will not come back on without being reset It can be reset by switching the 3 Position Switch to Off and waiting five minutes before switching the unit back on amp CAUTION If you need to con
15. lectric shock and injury to persons WARNING Do not attempt to wire your own new outlets or liquids in the vicinity of the heater amp CAUTION Clearance for air circulation beneath the fire place insert is provided by two rubber feet Do not install the fireplace insert directly on carpet or similar surfaces which may restrict air circulation amp CAUTION If installing the fireplace in a carpeted area place a one piece solid flat surface under the fireplace Ensure that both of the feet rest securely on this surface NOTE The dimensions of the circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician WARNING To reduce the risk of fire do not store or use gaso line or other flammable vapors or fireplace with the trim are 27 in 695 mm wide x 23 2 in 596 mm high x 8 3 4 in 222 mm deep Dimensions without trim are 26 74 in 663 mm wide x 22 7s in 580 mm Figure 1 27 98 m 695 mm 4 22 74 23 aa 596 mm mm 26 663 mm l N gy L 222 mm Fireplace Installation Figure 2 Figure 3 Log Set Assembly Trim Track high x 8 in 222 mm deep The fireplace does not require any additional venting Figure 1 Fireplace Assembly The only assembly required is to slide the Fro
16. limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna ncrease the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device www dimplex com Fireplace Installation WARNING Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons WARNING Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire e
17. mp CAUTION Read all instructions and warnings carefully before starting installation Failure to follow these instructions may result in a possible electric shock fire hazard and will void the warranty Please record your model and serial numbers below for future refer ence model and serial numbers can be found on the Model and Serial Number Label of your fireplace MODEL MOD LE MODELO MOD SERIAL No NUMERO DE SERIE NUMERO DE SERIE gt STOP NO NEED TO RETURN TO THE STORE Questions with operation or assembly Require Parts Information Product Under Manufacturer s Warranty Contact us at www dimplex com customer support For Troubleshooting and Technical Support Lam OR 4 Toll Free 1 888 DIMPLEX 1 888 346 7539 Monday to Friday 8 00 a m to 4 30 p m EST Please have your model number and product serial number ready See above amp IMPORTANT INSTRUCTIONS When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and injury to persons including the following D Read all instructions before using the electric fireplace 2 The heater is hot when in use To avoid burns do not let bare skin touch hot surfaces The trim around the heater outlet becomes hot during heater operation 3 Extreme caution is neces sary when any heater is used by or near childr
18. nt Glass onto the fireplace and install hardware to keep it in place 1 Remove fireplace and glass carefully from the carton dis card the plastic bag and foam packaging Remove the foam block from within the fireplace Figure 2 Using side cutters or scis Sors cut and remove the two cable ties as shown in Figure 2 and remove the cardboard that protects the Log Set As sembly 4 Remove the right hand side Trim by removing three Phil lips screws at the side of the fireplace Figure 3 5 Place the Front Glass onto the track of the fireplace Fig ure 3 and slide it along the front until it reaches the far left of the unit 6 Re attach the right hand trim piece using the three Philips screws from step 4 Mantel Installation Install the fireplace into the mantel refer to mantel assembly instructions IMPORTANT If not using a www dimplex com Fireplace Installation Figure 4 3 Plug the unit directly into a 15 23 587 mm NI 9 229 mm a Dimplex mantel the fireplace must be installed in an enclosure with the following minimum inter nal opening dimensions Figure 4 New Wall Construction 1 Mark the desired location on the floor 2 Use studs to frame an open ing of 26 in 679 mm wide 2 x 23 in 587 mm high x 9 in 229 mm deep Option 1 The power cord can be run from behind the Trim and along the wall to
19. orthwest Territories Hawaii or Alaska are not cov ered by this limited warranty Products purchased in these States provinces or territories are sold AS IS without warranty or condition of any kind including without limitation any implied warranties or condi tions of merchantability or fitness for a particular purpose and the entire risk of as to the quality and performance of the products is with the purchaser and in the To remove fingerprints or other marks the clear door can be cleaned with a damp cloth Fireplace Surface Cleaning Use a cloth dampened with warm water only to clean painted sur faces of the electric fireplace Do not use abrasive cleaners event of a defect the purchaser assumes the entire cost of all necessary servicing or repair What this limited warranty covers and for how long Products other than fireplace surrounds mantels and trims covered by this limited warranty have been tested and inspected prior to shipment Subject to the provisions of this warranty Dimplex warrants such products to be free from defects in material and workmanship for a period of 2 years from the date of the first purchase of such products as follows a a repair or replacement warranty on defec tive products or parts including in home services for the first year following the date of first purchase and b thereafter a replacement of parts warranty on defective products and parts with no in home ser vi
20. ought to the attention of Dimplex Technical Service by contacting Dimplex at 1 888 DIMPLEX 1 888 346 7539 or 1367 Industrial Road Cam bridge Ontario Canada N1R 7G8 Please have proof of purchase catalogue model and serial numbers available when calling Limited warranty service requires a proof of purchase of the product What Dimplex will do in the event of a defect In the event a product or part covered by this limited warranty is proven to be defec tive in material or workmanship during i the 2 year limited warranty period for prod ucts other than fireplace surrounds man tels and trims and ii the 1 year limited warranty period for surrounds mantels and trims you have the following rights Limited warranty service will be per formed solely by dealers or service agents of Dimplex authorized to pro vide limited warranty services For products other than surrounds mantels and trims for the period ending at midnight on the first anni versary of the date of first purchase Dimplex will in its sole discretion either repair or replace such defective prod uct or part without charge If Dimplex is unable to repair or replace such product or part or if repair or replace ment is not commercially practicable or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part This limited warranty entitles the purchaser to on site or in home w
21. place of business and all labour costs Such costs shall not be the responsibil ity of Dimplex Forsurrounds mantels and trims for the period ending at midnight on the first anniversary of the date of first purchase Dimplex will in its sole discretion either repair or replace such defective surrounds mantels and trims or part thereof without charge If Dimplex is unable to repair or replace such product or part or if repair or re placement is not commercially practica ble or cannot be timely made Dimplex may in lieu of repair or replacement choose to refund the purchase price for such product or part The purchaser shall not be entitled to on site or in house services The purchaser is re sponsible for all expenses incurred for repair or replacement of such product or part including without limitation all shipping costs and transportation costs to and from the authorized dealer s or service agent s business and all labour costs Such costs shall not be the responsibility of Dimplex On site or in home services not provided under this warranty may be performed at the purchaser s specific request and expense at Dimplex s then current rates for such services What Dimplex and its dealers and service agents are also not responsible for IN NO EVENT WILL DIMPLEX OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CON TRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDI
22. times you need to open the unit to replace light bulbs Care must be taken when removing the Log set as sembly as it contains LED s and wires DF2608 only CAUTION Allow at least five minutes for the light bulbs to cool before touching them to avoid ac cidental burning of the skin 1 Slide fireplace out of mantel 2 Layunit on it s back for safe removal of front glass 3 Remove three Phillips screws from the right side of trim 4 Remove trim 5 Slide glass to right side of fireplace to remove Figure 7 6 Pull the front edge of the plastic ember bed or plastic grate up and forward until the rear tab releases from the ledge located at the bottom of the partially reflective glass Figure 8 IMPORTANT Only handle the log set assembly by the em 14 www dimplex com oe Maintenance Trim Front Log Set Glass Assembly M ber bed or plastic grate NOTE Log set assembly fits tightly into firebox some force may be necessary to remove 7 Setlog set assembly in front of fireplace 8 Remove flicker rod by pulling rod to the right towards the flicker motor Bend the flicker rod enough to clear the brack et on the left lift out and pull flicker rod off of flicker motor shaft Figure 9 9 Remove four Phillips screws two per side which attach light filter bracket for easier access to light bulbs Figure 9 10 Unscrew bulbs counter clock wise to remov
Download Pdf Manuals
Related Search