Xtreme 18520 flat panel wall mount
Contents
1. can damage the items greatly reducing their holding power This products intended for indoor use only Using this product outdoors could lead to product failure and personal injury Kars MOUNTS AND BRACKETS Customer Service 877 536 8766 www XtremeCables net Component Checklist IMPORTANT Ensure you have received all parts against the component checklist prior to installing If any parts are missing or faulty telephone the special franchiser for a replacement Package M M4x10 x4 M5x10 x4 M6x10 x4 MBx15 x4 M A M B M C M D e 2 D4 04 5x010 D5 05 5x012 D6 06 3x016 D8 08 3x016 washer x4 washer x4 washer x4 washer x4 M E M F M G M H 013 5x05 5x3 2 x4 wire saddle x1 4mm allen key x2 Mi M J K Package W 5 mmm Cp ST5 5x50 lag bolt x3 concrete anchor x3 D6 06 6x012 WA WP washer x3 Tools required Phillips Head Screw driver 200mm length exclude the handle Electric drill and 8mm masonry bit for concrete wall installation Marking Pen Hammer m2 Insert the wire saddle M J to the holes firstly as shown below wire saddle WOOD STUD WALL MOUNTING WARNING Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Tighten wood screws firmly but do not over tighten Over tightening can d2. to use You should check whether screws are fixed well each two months If you have any doubts regarding the installation please consult our retailer or service department for detail mp
3. Tm MOUNTS AND BRACKETS Customer Service 877 536 8766 www XtremeCables net MOUNTS AND BRACKETS INSTALLATION INSTRUCTIONS Pitching angle 20 20 Swivel 180 Full Motion 17 37 HDTV Wall Mount Customer Service 877 536 8766 Model 18020 www XtremeCables net Max Load Capacity 30kg 66Ibs NOTE Read entire instruction sheet befc e you start installati N WARNING Do not begin the installation of the product before you have read and understood the instructions and warnings contained in this installation sheet If you have any question regarding any of the instruction or warning Please contact your local distributor Please refer to installation guide recommendation for required distance from wall to avoid risk of property damage This product should only be installed by someone of good mechanical aptitude with experience and basic building and fully understands Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Never exceed the maximum load capacity If mounting to wood wall studs make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Always use an assistant or mechanical lifting equipment to safely lift and position equipment Tighten screws firmly but do not over tighten Over tightening
4. amage the screws greatly reducing their holding power Make sure that mounting screws are anchored into the center of the studs Use of an edge to edge stud finder is highly recommended Hardware provided is for attachment of mount through standard thickness drywall or plaster into studs Installers are responsible to provide hardware for other types of mounting situations Customer Service 877 536 8766 www XtremeCables net Use a stud finder to locate the edges of the studs Use of an edge to edge stud finder is highly recommended Based on their edges draw a vertical line down each stud s center Place wall plate on wall as a template And mark the center of the three mounting holes Make sure that the mounting holes are on the stud centerline Drill three 1 8 3mm dia Holes 1 2 30mm deep Make sure that the wall plate is level secure it using three wood screws W A and three washers W C as shown in fig 1 1 SOLID BRICK AND CONCRETE BLOCK MOUNTING A WARNING When installing wall mounts on cinder block verify that you have a minimum of 1 3 8 of actual concrete thickness in the hole to be used for the concrete anchors Do not drill into mortar joints Be sure to mount in a solid part of the block generally 1 minimum from the side of the block It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of t
5. he hole when entering a void or cavity Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components Use the Wall Plate as a template to mark 3 holes locations on the wall as shown in fig 1 2 Pre drill these holes with a 8mm masonry bit to at least 60mm in depth Insert a Concrete Anchor W B into each of these holes Attach the Wall Plate to the wall using 3 wood screws W A and 3 Washers W C as in fig 1 3 ng Installing Adapter Plate Find the appropriate VESA attach the adapter plate to the back of the screen using the appropriate combination of screws washers as shown in fig 2 1 and fig 2 2 Begin with the proper screw hand thread through washer and adapter plate into screen as shown below Screw must make at least three full turns into mounting hole and fit snug into place Do not over tighten Repeat for remaining mounting holes level plate and tighten screws Pitching angle adjustment Use the tilt adjusting knob to adjust you TV to the desired angle the pitching angle can be adjusted between 20 20 as shown in fig 3 1 if you have any questions about this product contact the manufacturer for support do not return to retailer Tilt adjusting knob Maintenance Once you have mounted the bracket and the flat screen check that they are sufficiently secure and safe
Download Pdf Manuals
Related Search