Da-Lite Cinema Contour 123"
Contents
1. Power e 2 Pieces Da Tex Dual Vision Pearlescent Cinema Vision High Power Da Mat High Contrast Da Mat Audio Vision High Contrast Audio Vision High Contrast Cinema Vision and High Contrast Cinema Perf surfaces can be cleaned as follows Using a white clean cloth 10096 cotton preferred that is dampened with clear water gently wipe the area in one direction Do not use a circular motion Using a dry 100 cotton cloth wipe dry after each cleaning session To clean a stubborn stain or a sticky surface use denatured alcohol methanol or methyl alcohol following the same procedure as for water LIMITED ONE YEAR VVARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should b2. INSTRUCTION BOOK FOR Cinema Contour Screen DA LITE Included Hardware Large Wall Bracket 47 Long Installation screws not included Quantities vary by screen size Screens 80 and smaller viewing width 1 Screens over 80 to 96 viewing width 2 Screens over 96 viewing width 3 Quantity Included High Power Frame Bracket Screens with High Power quantity 2 Screens with 2 piece side frame rails quantity 2 Quantity Included Frame Assembly HAY Small Wall Bracket 8 Long Installation screws not included Quantity 1 Only for screens 80 and smaller viewing width Quantity Included e Snap Stud Quantity Included F 10 Screw Quantity Included Use Installation Method Number 1 Unwrap the frame pieces Assemble frame pieces on padding material or other soft clean surface This will help keep the frame clean and protect it from scratches 2 Slide the frame pieces together at corners Note Frame assembly holes may not appear to fit properly at the corners until all fasteners have been attached Once fasteners are attached the frame corners will be drawn in for a proper fit Secure frame pieces with 10 screws provided Do not tighten screws until all are started then tighten See Figure 1 NOTE The frame pieces are labeled top and bottom Be sure the frame pieces are assembled according to the labels This will ensure the sn
3. your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite com VVVVVV da lite com DL 0283 12 13 2013 Milestone AV Technologies LLC Printed in U S A 87070
4. A Large VVall Bracket Overall A o Height Overall Height Less 1 y 1 Small Wall Bracket el Figure 3 3 2 Lift T x Figure 4 1 To install the lovver vvall bracket you must measure the overall height of the screen frame and subtract 1 3 8 Using that dimension measure dovvn from the top edge of the vvall bracket and mark the wall for two screw holes The holes should be centered within the frame and 6 apart Refer to Figure 3 Attach the small wall bracket to the wall Refer to Figure 4 for proper orientation Do not tighten the screws completely The bracket should slide up and dovvn easily Unroll the screen on a clean surface Do not use nevvspaper The vievving side is rolled to the inside of the roll Place the rame over the screen surface and vvhile lifting the frame with one hand snap the screen surface onto the frame with the other hand while maintaining a steady pull on the surface Hang the screen on the brackets by hooking the bottom of the frame onto the lovver vvall bracket and lift up until you can hook the top of the frame on the top bracket Push dovvn on the frame to seat it on the brackets Refer to Figure 4 Method 2 Screens Over 80 Up To 96 In Viewing Width Method 3 Screens Over 96 In Viewing Width 1 Secure the wall bracket to wall studs at the desired height Make sure the bra
5. ap pattern on the frame and screen surface will match 3 Attach the eight snap studs to the back of the frame in the predrilled holes Z Screws Snaps 4 R Figure 1 Rear View Installation here are four methods of installation based on the size of the screen and type of viewing surface Measure the width of the ewing area of your screen and refer to the appropriate method f installation below The wall bracket diagram shows the type and quantity of bracket s supplied based on the size of the T vi o screen ethod 1 Screens 80 and smaller in viewing width ethod 2 Screens over 80 up to 96 in viewing width ethod 3 Screens over 96 in viewing width ethod 4 Any size screen with High Power viewing surface Method 1 Screens 80 And Smaller In Viewing Width Method 1 Screens 80 And Smaller In Viewing Width 1 Secure the wall bracket to wall studs at the desired height Make sure the bracket is level The top of the frame will be 1 8 above the top of the wall bracket when mounted You will need at least 5 8 clearance above the bracket to hang the screen Figures 2 3 and 4 show the proper orientation for the supplied wall brackets Large Wall Bracket o 1 Piece Small Wall Bracket Figure 2 l Piece o o o o o o o o o o o o il
6. cket is level The top of the frame will be 1 8 above the top of the wall bracket when mounted You will need at least 5 8 clearance above the bracket to hang the screen Figure 5 and 6 show the proper orientation for the supplied wall brackets Figure5 Large Wall Bracket 2 Pieces Overall Height Overall Height Less Y Wall Figure 6 To install the bottom large wall bracket vou must measure the overall height of the screen frame and subtract 1 4 This is the dimension from the top of the upper wall bracket to the bottom of the bottom wall bracket See Figure 6 Unroll the screen on a clean surface Do not use newspaper The viewing side is rolled to the inside of the roll Place the rame over the screen surface and while lifting the frame with one hand snap the screen surface onto the frame with the other hand while maintaining a steadv pull on the surface Position the screen with the attached surface onto the top wall bracket as shown in Figure 6 Push down at the center of the bottom frame rail to hook onto the lower wall bracket 1 Secure the wall brackets to wall studs at the desired height Make sure the brackets are level The top of the frame will be 1 8 above the top of the wall bracket when mounted You will need at least 5 8 clearance above the bracket to hang the screen Figure 6 and 7 show the proper orientation for the suppli
7. e made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and
8. ed wall brackets ZI a S o E Large Wall Brackets High Power 3 Pieces Bracket for lih lt Large Split Frames Only 2 Pieces Figure 7 To install the bottom large wall bracket you must measure the overall height of the screen frame and subtract 1 4 This is the dimension from the top of the upper wall bracket to the bottom of the lower wall bracket See Figure 6 Some large screen sizes 240 are made with 2 piece side frame rails For this type of frame you will need to attach one High Power bracket to each side at the joint Use the black 10 screws supplied See Figure 7 Unroll the screen on a clean surface Do not use newspaper The viewing side is rolled to the inside of the roll Place the frame over the screen surface and while lifting the frame with one hand snap the screen surface onto the frame with the other hand while maintaining a steady pull on the surface Position the screen with the attached surface onto the top wall bracket as shown in Figure 6 Push down at the center of the bottom frame rail to hook onto the lower wall bracket If you attached brackets to the side frame rails in step 3 anchor these to the wall with an appropriate fastener for your type of wall Method 4 High Power Cleaning Bracket 1 Piece 10 Screws 4 Pieces Figure 8 Large Wall High Brac
Download Pdf Manuals
Related Search