Home
        Breville VKJ367 electrical kettle
         Contents
1.   Press to start the boil sequence     Dispensing control  This control allows you to select the amount of water dispensed by your Hot Cup   Move it towards    for less water or e for more water     Lid flap release button   Press to open the lid flap only and fill the water tank    BRITA  Memo   Shows you when you need to change the BRITA  MAXTRA  water filter cartridge   Removable lid   The complete lid can be lifted off your Hot Cup to access the filter and filter funnel     Filter funnel and filter cartridge  inside water chamber       Water chamber  12   13     Power base    BRITA  MAXTRA  water filter cartridge       Preparing the BRITA   MAXTRA   Cartridge          Remove the cartridge from its wrapping  it is normal for  the cartridge to appear moist during storage      2  Immerse the cartridge in cold tap water and shake gently  to remove any air bubbles  There is no need to pre soak  this cartridge before use     3  Lift the complete lid off your Hot Cup and remove the  filter funnel  Insert the cartridge into the filter funnel  and push it firmly into place  When correctly fitted  the  cartridge should remain in place when the funnel is turned    upside down   El      4  Fill the filter funnel with cold tap water up to the MAX    mark and allow it to filter through discarding the water  y  Repeat this process  again discarding the water     5  The BRITA  MAXTRA  cartridge is now ready for use   You do not need to keep the filter cartridge immersed in  water  Refit 
2.   quality which can lead to environmental damage and which can also lead to  negative impacts on human and animal health     Recycling household electrical equipment     regulations    With effect from July 2007  the UK s Waste Electrical and Electronic Equipment   WEEE  Regulation require that all producers of electrical equipment are now  obliged to pay for recycling of household electrical goods  where previously this  bill was met by councils or items were not recycled at all  These regulations  also require that all retailers both actively assist in delivering a UK wide WEEE  collection infrastructure and encourage the participation of consumers in  recycling electronic equipment     So that you can get your waste electrical goods recycled  we have contributed  towards a national fund to assist local councils to further develop their existing  waste electronics collection facilities  which will in turn allow producers of this  equipment to meet their obligations     18       The Crossed out Wheeled Bin Symbol   All new electrical and electronic equipment should be marked with the crossed  out wheeled bin  which aims to encourage you to separate out WEEE from  other household waste and to dispose of it at a recycling facility     recycle more co uk   For advice on all aspects of recycling  to find out how to minimise your effect on  the environment and locate your nearest recycling facilities for electronic waste  please visit www recycle more co uk and use the recycle mo
3.  being vented in a This is normal operation  the start button and behind controlled manner through  the dispensing nozzle designed vents    The water reservoir is getting   Hot water is being returned This is normal operation   hot  to the water reservoir    Your Hot Cup immediately Your Hot Cup is already Press the stop button   turns iteslf on when it is switched on   placed on the power base        14    Connection to the mains supply       This appliance is fitted with either a moulded or rewirable BS1363  13 amp plug  The   fuse should be rated at 13 amps and be ASTA approved to BS1  362    If the fuse in a moulded plug needs to be changed  the fuse cover must be refitted  The   appliance must not be used without the fuse cover fitted    If the plug is unsuitable  it should be dismantled and removed from the supply cord   and an appropriate plug fitted as detailed below  If you remove the plug it must not be   connected to a 13 amp socket and the plug must be disposed of immediately    The wires of the mains lead are coloured in accordance with the following code   GREEN YELLOW   EARTH BLUE   NEUTRAL BROWN   LIVE    The wire which is coloured GREEN YELLOW must be connected to the terminal in  your plug which is marked with an E or by the earth symbol     or coloured GREEN or  GREEN  YELLOW     The wire which is coloured BLUE must be connected to the terminal in your plug which  is marked with the letter N or coloured BLACK    The wire which is coloured BROWN must be conn
4.  on position  itself after the boiling cycle  after the last boil cycle  Wait  a few seconds for it to cool  slightly before trying again     The water tank does not Your Hot Cup is not   Check your Hot Cup is  illuminate and your Hot Cup plugged in  plugged in and switched on  does not dispense boiling Your Hot Cup is not at the supply socket     water  positioned correctly on its Check that the dispensing  power base  nozzle is positioned    The fuse has blown  centrally over the drip tray     Your Hot Cup has boiled Check the fuse in the plug    dry  Allow your Hot Cup to  cool down completely then  refill it with water     Your Hot Cup does not Your Hot Cup has Descale your Hot Cup  dispense a full cup of water excessive scale  Adjust the dispensing    The dispensing control may control  be set too low     Your Hot Cup produces There is not enough water Fill with water up to the  excess steam but does not in your Hot Cup  MAX marking then restart  dispense boiling water  Your Hot Cup has the boil cycle     excessive scale  Descale your Hot Cup     Your Hot Cup makes a This is the sound of the This is normal operation   noise and there is a    clunk    internal valve operating after   sound after water has been the boil cycle finishes    dispensed     Water drips from the There is a residual amount This is normal operation  dispensing nozzle after the of water left inside your Hot  boil cycle has finished  Cup after the boil cycle     Steam comes out from behind   Steam is
5.  pulse uk co uk    16    Guarantee       Please keep your receipt as this will be required for any claims under this guarantee     This appliance is guaranteed for   year after your purchase as described in this  document     During this guaranteed period  if in the unlikely event the appliance no longer functions   due to a design or manufacturing fault  please take it back to the place of purchase  with   your till receipt and a copy of this guarantee    The rights and benefits under this guarantee are additional to your statutory rights    which are not affected by this guarantee  Only Jarden Consumer Solutions  Europe    Limited     JCS  Europe      has the right to change these terms    JCS  Europe  undertakes within the guarantee period to repair or replace the appliance    or any part of appliance found to be not working properly free of charge provided that    e you promptly notify the place of purchase or JCS  Europe  of the problem  and     the appliance has not been altered in any way or subjected to damage  misuse   abuse  repair or alteration by a person other than a person authorised by JCS   Europe     Faults that occur through  improper use  damage  abuse  use with incorrect voltage  acts   of nature  events beyond the control of JCS  Europe   repair or alteration by a person   other than a person authorised by JCS  Europe  or failure to follow instructions for use   are not covered by this guarantee  Additionally  normal wear and tear  including  but not   li
6. Breville      Instructions for use       Important Safety Instructions       READ CAREFULLY AND KEEP FOR FUTURE REFERENCE    This product can be used by children aged 8 years and above  and   persons who require supervision  provided      they are familiar with the hazards associated with the product   and      theyreceive instruction by a competent person on how to  safely use the product    Children must not play with the product  Cleaning and user   maintenance must not be done by children unless they are aged 8   or older and are supervised    Never use a power base other than the one supplied with the   appliance    Never fill the kettle above the MAX marking  If the kettle is   overfilled  boiling water may be ejected    If the supply cord is damaged  it must be replaced by the   manufacturer  its service agent or similarly qualified persons in   order to avoid a hazard        ANThis appliance generates heat during use  Adequate precaution must be taken to  prevent the risk of burns  scalds  fires or other damage to persons or property caused  by touching the exterior whilst in use or during cooling     A Never use this appliance for anything other than its intended use  This appliance is for  household use only  Do not use this appliance outdoors     AN Always ensure that hands are dry before handling the plug or switching on the  appliance     AN Always use the appliance on a stable  secure  dry and level surface   A Never use a power base other than the one supplied 
7. anging the MAXTRA   cartridge more frequently  you will need to descale less  often  BRITA  recommends to exchange the MAXTRA  cartridge every 4 weeks     l  Completely remove the lid and remove the filter funnel and filter  Fill your Hot Cup  to the MAX marking on the water chamber and place an empty cup on the drip  tray  Replace the lid  Select a suitable setting for the dispensing control and press the  start button  Wait for the water to be dispensed into the cup     2  Add a citric acid based proprietary descaling product to the hot water in the cup  and stir     Tip the contents of the cup into your Hot Cup and close the lid   Place the empty cup on the drip tray and press the start button   Wait for the water to be dispensed into the cup     Discard the water from the cup     N Qv   m de 9    Repeat steps 4  5 and 6 until your Hot Cup is empty  Fill your Hot Cup with fresh  water to the MAX fill level and place an empty cup on the drip tray     8  Press the start button and wait for the water to be dispensed into the cup   9  Discard the water in the cup     10  Repeat steps 8 and 9 until your Hot Cup is empty  This will rinse any remaining  descaling solution from your Hot Cup    11  When your Hot Cup is completely cleaned  reinsert the filter funnel and filter  Your  Hot Cup is ready for use again     12       13    Troubleshooting    Problem Possible Cause Solution    The start switch will not stay   Your Hot Cup has not reset Your Hot Cup is still too hot   in the
8. ected to the terminal in your plug  which is marked with the letter L or coloured RED     If any other plug is used  a 13 amp fuse must be fitted either in the plug or adaptor or at  the distributor board     Plug should be BS1363 approved  Fita 13 Amp Fuse    GREEN YELLOW   Earth        13 Amp  Fuse    BLUE   Neutral     Ensure that the outer sheath of the cable  is firmly held by the clamp          19    After sales service       These appliances are built to the very highest of standards  There are no user  serviceable parts  Follow these steps if the unit fails to operate     Check the instructions have been followed correctly   Check that the fuse has not blown   Check that the mains supply is functional     If the appliance will still not operate  return the appliance to the place it was purchased  for a replacement  To return the appliance to the Customer Service Department  follow  the steps below     Pack it carefully  preferably in the original carton   Ensure the unit is clean   Enclose your name and address and quote the model number on all correspondence   Give the reason why you are returning it     If within the guarantee period  state when and where it was purchased and include proof  of purchase  e g  till receipt      Send it to our Customer Service Department at the address below     Customer Service Department  Jarden Consumer Solutions  Europe  Limited  Middleton Road  Royton  Oldham  OL2 5LN  UK   Telephone  0161 621 6900 Fax  0161 626 0391  e mail  info
9. funnel  Allow  the water to filter through into the water chamber  Repeat until the water level in the  chamber is no higher than the MAX marking on the water chamber     3  Close the lid and press the stop button  This will make sure that your hot cup will not  immediately start a boil cycle when you place it onto the power base   Connect your Hot Cupto a mains supply socket    5  Place a suitable cup or container with a tea bag  coffee  sugar  etc  below the  dispensing nozzle  Never operate your Hot Cup without a cup or suitable container  placed below the dispensing nozzle  Adjust the dispensing control to the required  setting  The control adjusts the quantity of boiling water dispensed by your Hot Cup   For smaller cups like teacups  set the control towards the w setting  for larger cups  like coffee mugs  set the control towards the IP setting  If you are not sure which  setting to use  it s best to use a lower setting until you gain experience using your Hot  Cup    Press the start button  The body will light up blue and your Hot Cup will start to boil   The selected quantity of boiling water will be dispensed into the cup  Your Hot Cup  is now ready to use again  If  after just having boiled  the start button doesn t operate   simply wait a few seconds before trying it again     Stopping your Hot Cup   If you have started the boil procedure and then decide you want to stop your Hot Cup for  any reason  simply press the stop button  You can also stop water that is bei
10. mited to  minor discoloration and scratches are not covered by this guarantee     The rights under this guarantee shall only apply to the original purchaser and shall not  extend to commercial or communal use     If your appliance includes a country specific guarantee or warranty insert please refer  to the terms and conditions of such guarantee or warranty in place of this guarantee or  contact your local authorized dealer for more information     Waste electrical products should not be disposed of with household waste  Please  recycle where facilities exist  E mail us at info pulse uk co uk for further recycling and  WEEE information     Jarden Consumer Solutions  Europe  Limited  Middleton Road   Royton   Oldham   OL2 5LN    UK ERA    Recycling       The MAXTRA  cartridge is 100  recyclable  Look out for BRITA  recycling  points in major retailers or visit www brita co uk for more information     Waste Electrical and Electronic Equipment  WEEE     WEEE is the fastest growing waste stream in the UK  growing by at least 596  each year  The UK public alone dispose of over 1 2 million tonnes of electrical  and electronic waste every year  this would fill the new Wembley Stadium six  times over     Much of the UK s electronic waste ends up in landfill sites  It has been  estimated that landfill space in the UK will run out within the next 10 years if  we do not increase the amount of waste we recycle     WEEE that is not recycled can have negative impacts on soil  air and water
11. ng dispensed  by pressing the stop button  The boiled water will be safely transferred back into the  water reservoir     8       Cleaning       A Always switch off and unplug your Hot Cup and allow it to completely cool  before cleaning  Never immerse the base unit  power cord or plug in water or  any other liquid  Do not use harsh abrasives  chemicals or oven cleaners     Emptying your Hot Cup       Fill your Hot Cup with a quantity of water that just covers the perforated stainless  steel element cover     2  Place a suitable cup or container below the dispensing nozzle  Set the dispense  control to the BP setting     3  Press the start button     4  After the water has been dispensed  empty the cup and replace it under the  dispensing nozzle     5  Press the start button again   6  Discard the water   Your Hot Cup is now empty     If your Hot Cup will not be used for an extended period  e g  if you are on holiday   we  recommend that you first empty it     Before using your Hot Cup again  carry out several boil cycles discarding the water each  time     Cleaning    Clean the exterior surface of your Hot Cup with a damp cloth and then polish it with a  soft  dry cloth  Do not use steel wool pads or harsh abrasive cleaners     10       11    Descaling       Descaling your Hot Cup    To maintain it s performance  your Hot Cup will require descaling once every three  months or so  You may need to descale your Hot Cup more frequently if you live in a  hard water area     By ch
12. r cartridge available    4  After 4 weeks  all four bars will disappear and a flashing  arrow will appear to indicate that the cartridge should be  replaced    Wash and dry the filter funnel  insert a new cartridge and   restart the Memo as described above    Please note that the Memo is only intended to be used with   BRITA   filter cartridges    More information on the use of BRITA  water filter cartridges   and the Memo can be found in the BRITA  information guide        Using Your Hot Cup       Before using your Hot Cup for the first time     Remove your Hot Cup carefully from the box  Remove any packaging and  promotional material and position your Hot Cup on a dry  level  secure work surface  away from the edge      Follow the instructions below and discard the first full tank of water  This will remove  any residues that may remain from the manufacturing process     e Fit the filter funnel and the BRITA   MAXTRA   water filter and set the BRITA  Memo     see pages 6 and 7     Using your Hot Cup   A Always position your Hot Cup in such a way that the start button cannot be   accidentally operated  especially by children  As you use your Hot Cup  a certain   portion of the water boiled will be transferred back to the water reservoir  This   will mean the water reservoir may become hot  Always use care when handling   your Hot Cup    Il  Press the lid flap release button to open the lid flap    2  Fill the filter funnel from your cold tap up to the MAX mark on the filter 
13. re bank locator   Recycle more co uk also offers top tip and advice on all aspects of recycling   making it easier and quicker to protect our environment and recycle more     cle   eN Sm   7S  DA    3 a    9    AE  o       19    Breville         2013 Jarden Consumer Solutions  Europe  Limited    All rights reserved  Imported and distributed by Jarden Consumer Solutions  Europe  Limited   Royton  Oldham OL2 5LN  United Kingdom   The product you buy may differ slightly from the one shown on this carton due to continuing product development   One  1  Year Limited Warranty   see inside for details   Jarden Consumer Solutions  Europe  Limited is a subsidiary of Jarden Corporation  NYSE  JAH    Made in PRC  www  breville co uk    VKJ367_Iss_2 09 13 93233 1          
14. the filter funnel and filter into your Hot Cup   Replace the lid     6  Always make sure that you have spare MAXTRA   cartridges to hand  When buying new cartridges look for  the BRITA  MAXTRA  logo on the cartridge packaging    7  Whenitis time to replace the BRITA  MAXTRA  filter  cartridge after 4 weeks use  simply lift the handle on top  of the cartridge and pull upwards to remove  BRITA     cartridges are 100  recyclable  Visit www brita co uk or 6  call the BRITA   Care team on 0844 742 4800 for further    information on participating retailers   8  Repeat steps l 5 with a new cartridge  L1       Using the BRITA   Memo Function       It is important to change your BRITA  filter cartridge regularly   to enjoy the benefits of BRITA  filtered water  Filtering your LU   water improves the look and taste of hot drinks by reducing  limescale  chlorine  metals and other impurities     The BRITA   Memo automatically reminds you when your  filter cartridge needs to be changed  BRITA  recommend to  exchange the MAXTRA   cartridge every 4 weeks     When you have fitted and prepared your filter cartridge  start  the Memo as follows     I  Press and hold the START button until 4 bars appear on  the display and flash twice  The Memo is now set     2  The flashing dot in the corner of the display indicates that  the Memo is working     3  Every week  one bar will disappear to indicate the  remaining cartridge life  When only one bar is showing   check that you have a replacement filte
15. with the appliance     A   This appliance must not be placed on or near any potentially hot surfaces  such as a  gas or electric hob      AN Do not use the appliance if it has been dropped  if there are any visible signs of  damage or if it is leaking     As Ensure the appliance is switched off and unplugged from the supply socket after use  and before cleaning     AN Always allow the appliance to cool before cleaning or storing    A Never immerse any part of the appliance or power cord and plug in water or any  other liquid    A Never let the power cord hang over the edge of a work top  touch hot surfaces or  become knotted  trapped or pinched    A Never leave the appliance unattended when in use    AN Beware of steam coming from the spout or lid especially during refilling  Never open  the lid during the boiling cycle    A Never fill the appliance when it is positioned on the power base    A Never use the appliance without sufficient water in it for it to operate correctly    A Never allow the appliance to boil dry     A Always operate the appliance with a cup or suitable container placed below the  dispensing nozzle     Identifying the Parts    10        Removeable drip tray   No mess  just lift it off the power base and rinse under the tap  Holds over   cup of  water before it needs emptying    Removable stainless steel drip tray cover   Dispensing nozzle   Stop button   Press to immediately stop the boil sequence or to stop water that is being  dispensed    Start button 
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
capítulo 3: correção do fator de potência  INSTALLATION MANUAL NOTICE D`INSTALLATION  Anais do V – Simpósio - Instituto de Botânica de São Paulo  算 数  別紙発電所案内図等  piano comunale di protezione civile  Projecta Multi-Mask Imager 160x229 Matte White D    Copyright © All rights reserved. 
   Failed to retrieve file