Elite Screens Saker Tab-Tension 135"
Contents
1. LITE SCREENS Electric Motorized Wall Ceiling Projection Screen Saker Tension Series User s Guide Make sure to read this user s guide and follow the procedures below Caution The screen s Black Top Drop is already set to its maximum drop distance There is NO extra Black Top Drop in the roller Please be aware of this as it will void your warranty with Elite Screens Unapproved changes or modifications except for cutting the power cord for hardwire installations to this unit are prohibited and will void your warranty For more information please contact our Technical Support Department at 877 511 1211 Ext 604 e Please retain this user s guide for future reference e To avoid damaging the unit do not use with any unauthorized accessories not recommended by the manufacturer e Handle the unit carefully during transportation to avoid any damages e To ensure safe and reliable operation direct connection to a properly grounded power source is advised e The power outlet supplying power to the unit should be close to the unit and easily acc e Do not install the unit on uneven or inclined surfaces e Do not put heavy objects on the power cord and position it properly to avoid creating a trip obstacle e Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short circuit e There are not user serviceable parts in thi No one except authorized technicians can open and make repa2. 6 Wireless 5 12 volt trigger Item F Fig 5 The RF remote control serves as a dual purpose independently as a handheld remote control or in conjunction with the Wireless 5 12 volt trigger cable The radio frequency technology can be programmed to send a wireless signal to synchronize its drop amp rise with the projector s power cycle Here s how to set up your Wireless 5 12 volt trigger Synchronization Instructions Step 1 Connect the wireless 5 12 volt trigger cable to the RF remote 3 5mm 4 Step 2 Connect the 12 v adaptor end of the wireless 5 12 volt trigger cable to your projector u Step 3 Make sure to unplug your screen from the power outlet Step 4 Hold the UP button on your RF remote Step 5 While holding the UP button plug the screen back to the power outlet Step 6 Wait 5 seconds and then release the UP button Step 7 Your 5 12V wireless trigger should now be activated with your screen and ready to be used and able to control your screen with your projector s power cycle Repeat the steps again if not successful Please be aware the projector on off cycle may take longer to fully activate It usually takes around 20 30 seconds for full off and on cycle each time The back of the projector F Figs DC 5 12V out va Wireless 5 12V trigger cable up Stop Down For more information technical support or your local Elite Screens c
3. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that the interference will not occur on a particular installation If this equipment causes harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Y Reorient or relocate the recei interference v Increase the separation between the screen and the device s receiver Y Connect the equipment into a different power outlet other than the device ing antenna of the device which may be causing the Installation 1 Carefully unpack the screen Always handle the screen in a leveled position on a clean surface In order to protect the screen from exposure to stains keep the screen out of contact with foreign particles such as dust sawdust and or liquids Regardless of the mounting method the screen should be securely supported so that the vibration or pulling on the viewing surface will not cause the
4. casing to become loose or fall The installer must insure that the fasteners used are of adequate strength and suitable for the installation location Please make sure all parts listed below are included before proceeding with the installation A Wall Ceiling mount B M4x50 Screw x4 C M10 Dry wall D Bracket E M5x15 Bolt bracket x2 anchor x4 connector x2 Screw x4 2S e eyy F M5x25MM round G M5x30MM eyebolt H Hidden wall 1 R18xR6x1 washer head cross screws x2 screw amp M5 nut x2 bracket x2 x4 051215 JA 2 www elitescreens com Installation In For installation assistanc A Wall Mount ite pleas consult a professional Installer Elite Screens is not liable for faulty installations I Flush mount with wall ceiling brackets fixed position M5x15 Bolt Screw Ww ee SoH Bracket connector 0 Wall Ceiling Mount by sliding the bracket connector D all the way to each end of the housing Bracket A en attach it to the wall ceiling mount bracket A with the M5x15 bolt screw E 3 Measure and mark the WxH distance between the two holes on each bracket 4 Drill a hole for each screw hole on the marked areas 5 Insert a dry wall anchor C into the wall 6 Insert a M4x50 Screw B in each dry wall anchor C and screw it in leaving about 1 8 of an inch 7 Hang the screen by aligning the end cap holes to the M4x50 screws B Maxso 7 s
5. ded 1 Screw the eyebolt G on the bracket connector D 2 Attach the snap link J thru the eyebolt G and connect it to an eyebolt screw not included rated for the screen s weight Remove the weight bar end cap Wrench counter clockwise and the screen will lose tension Please note this adjustment ion of the screen has been set to its factory setting for best performance Please contact Elite Screens ance to avoid damaging the screen and voiding your warranty at techsupport elitescreens com expose the adjustment tension knob Insert your 4mm Allen Wrench to push in the adjustment tension knob turn clockwise and your screen will gain more tension Turn the Allen 051215 JA Tension knob s not necessary as www elitescreens com E IR extended eye receiver F Wireless 5 12v trigger cable G AAA batteries H Bubble leveler B ffig Oe Hg I j 8 3 S s Screen operation Electric Current The screen operates on AC110V 60hz 1 Plug the screen s power cord into a power outlet 2 Once the screens has power you ll be able to control it using any of the 6 methods described below SCRE Seng Lite G 6 ways to control your Saker Tension 1 IR remote control Item A Fig 1 The Infrared functions by direct line of sight contact with a beam range of 30 feet Aim the IR remote at the circ
6. i s e Make sure the power source this unit is connected to has a continuous power flow e If there is need to use an extension cord make sure the cord has an equal rating as the appliance to avoid overheat e Do not handle the power plug when your hands are wet or your feet are in contact with water ible s unit Do not attempt to disassemble this unit by yourself Do not use this unit under the following circumstances Disconnect the power cord under the conditions of heavy rain wind thunder or lightning Avoid direct Sunshine rain shower and moisture Keep away from fire sources and high temperature to prevent this device from overheating Cut off the power supply first before transportation or maintenance Fully disconnect from the power supply when the unit is not in use for a long period of time as should be done with any other electric household appliance To avoid possible injury and or an electric shock do not attempt to use the screen if there is obvious damage or if there are any evident broken parts 051215 JA 1 www elitescreens com The Screen s Top Black Drop is already set to its maximum drop distance There is NO extra top black drop in the roller Please be aware of this as it will void the limitation of your warranty Individual modifications to this product are prohibited and will void the warranty with the manufacturer Please contact Elite Screens Customer Service for any questions
7. ontact please visit www elitescreens com 051215 JA 6 www elitescreens com
8. ores b fm II Flush hidden mount movable position This mount method allows the screen to slide horizontally Front view of bracket h Side view of bracket h 1 Determine where the screen will be installed Then measure and mark the distance between the top and bottom screw holes from each hidden wall mount bracket H 2 Drill a hole on all marked areas and install the brackets with the dry wall anchor C M4x50 screw B and a washer I Make sure both brackets are properly leveled 3 Hang the screen by placing the downward catch located on the back over the brackets upper catch 4 After making sure the screen is secured you can slide it left right to properly center it in position 5 Lastly screw the M5 screw F into the upper hole of the bracket to add additional support for the screen 051215 JA 3 www elitescreens com B Ceiling Mount I Flush Ceiling Mount Dry wall anchors C Ceiling AY _ Max50 screw B k p S a Washer 1 i 1 Determine where the screen will be installed Then measure and mark the distance between the WxH locations Drill a hole on all marked areas and insert a dry wall anchor C 3 Secure the screen by inserting the M4x50 screw B and a washer 1 thru the wall ceiling mount brackets A Two or more people are required while one holds the screen in place TI Suspen
9. ular window located on the left side of the screen O4 up O4 STOP 2 IR Eye Receiver Item E Fig 2 The IR Eye Receiver plugs O lt DOWN directly into the screen s RJ 45 input to present a low profile line of sight control option for your IR remote control even in a recessed ceiling Fig l installation one IR RF remote 3 RE Remote Control Item B The radio waves eliminate the need for a direct line of sight with a range of 100 feet 4 3 Way Wall Switch Item C Fig 3 The 3 way wall switch is a wall mount control box with an up stop down button and plugs directly into the screen s RJ 45 input Fig 2 0 L 5 T 9 Beye receiver A 3 Way wall Switch does not have IR sensor 051215 JA 5 www elitescreens com 5 5 12 volt trigger Item D Fig 4 The built in 5 12V trigger input allows your screen to synchronize its drop amp rise with the projector s power cycle The screen deploys when the projector powers up and will retract when the projector powers down The 5 12 volt RJ45 cable connects to your projector s trigger output via a separate cable that may or may not be provided by the manufacturer of the projector The trigger feature will not work without an output cable from the projector but it can be tested by connecting the Red and Green cable to a 9 volt battery 5 12 volt trigger cable
Download Pdf Manuals
Related Search