KitchenAid KCDC 1160 cooker hood
Contents
1. IMPORTANT Avoid temperatures above 65 C during washing IMPORTANT The manufacturer declines any liability for colour alterations due to the use of aggressive detergents LIGHTING SYSTEM Ay WARNING e Use protective gloves e Disconnect the appliance from the power supply IMPORTANT Make sure the lamps are cold before touching them To replace the lamps proceed as follows Pull the hood extraction panel downwards a little with both hands The extraction panel is released and by means of the cylindrical actuator gradually turned downwards allowing access to the lamps 2 Remove the glass protection cover with the aid of a screwdriver 3 Remove the burnt out lamp and replace it with one having the same characteristics Halogen type G4 21520 12 V 35 Watt 4 After replacing the lamp refit the glass cover snap on 4 Material supplied Remove all the parts from the packets and make sure all the components listed below are included e 4 4 Plugs O10 e 4 washers e 4 Threaded sleeves e 444 Screws M8 e 444 Nuts e Threaded rod length 100 cm e Flange 120 cm e Remote control The material for the external motor included in the previous list is supplied separately in the motor packing 4x 4x Installation Preliminary assembly instructions A WARNING e Installation and maintenance must be carried out by a specialised technician The hood is designed for installation and2. LED 5 Motor MAXIMUM power The motor automatically returns to power level 3 after 5 minutes LED 6 Grease filter saturation indicator Printed in Italy 06 11 5019 718 02046
3. not be dispersed in the environment but disposed of in compliance with the local regulations Product disposal This appliance is marked in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE Troubleshooting guide The hood does not work Make sure e There is not a power outage e A certain speed is actually selected The hood does not extract sufficiently Make sure By ensuring the correct scrapping of this product the user can help prevent potentially negative consequences for the environment and the health of people X The symbol mw on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection centre for the recycling of electrical and electronic equipment e The selected speed is sufficient for the amount of fumes and steam present e The kitchen is adequately ventilated to allow an air inlet e The air exhaust tube is free of obstructions The hood stops during operation Make sure e There is not a power outage e The differential thermal magnetic switch Safety Cutout has not tripped The light does not work e Check if the lamp needs replacing e Make sure the lamp is correctly fitted The remote control does not work e Check if the batteries need replacing e Make sure the lithium batteries are correctly fitted After Sales Service Before contacting the
4. use in Extractor Version The hood must be installed away from very dirty areas windows doors and heat sources IMPORTANT The hood comes with all the material necessary for installation on the majority of ceilings To guarantee correct installation contact a qualified technician or an architect to make sure the materials used for the ceiling are suitable The steam is removed to the outside through an exhaust pipe fixed to the connection flange The diameter of the hood body and motor connection flange is 200 mm The diameter of the exhaust pipe must be at least 200 mm Provide for a fixing system suitable for the connection flange IMPORTANT If the exhaust pipe is not supplied it must be purchased separately Installation dimensions IMPORTANT For the operation of this hood it is necessary to install the external motor included in a separate pack IMPORTANT For gas hobs the maximum total power is 16 2 kW Installation assembly instructions WARNING e Installation and maintenance must be carried out by a specialised technician Very heavy product hood handling and installation must be carried out by at least two people The instructions below in numerical order refer to the drawings giving the same numbering in the Installation instructions manual Position the external motor and fix it using the material supplied IMPORTANT The external motor must be protected against atmospheric agents a
5. After Sales Service See if you can eliminate the problem on your own by consulting the Troubleshooting guide 2 Switch the hood off and then on again to check if the problem has been eliminated If the following faults occur contact the After Sales Service immediately e The hood makes strange noises and you are unable to detect any fault in it The motor runs unevenly or strange noises can be heard or it is faulty e Switching does not work regularly If the problem persists after carrying out the above checks contact the nearest After Sales Service Always specify A brief description of the fault e The type of appliance and exact model Cleaning Ay WARNING Do not use steam cleaners e Disconnect the appliance from the power supply IMPORTANT Do not use corrosive or abrasive detergents If any of these products comes into contact with the appliance clean it immediately with a damp cloth e Clean the surfaces with a damp cloth If very dirty add a few drops of washing up detergent to the water Dry with a dry cloth IMPORTANT Do not use abrasive sponges or metallic scrapers or scouring pads Their use could eventually spoil the enamelled surfaces e The Service number the number after the word SERVICE on the dataplate inside the appliance The Service number is also given in the warranty booklet Your full address e Your telephone number AAA 0000 000 00000 If any repairs ar
6. Instructions for use AN KitchenAid le FOR THE WAY IT S MADE Important safety instructions Installation Advice on safeguarding the environment Troubleshooting guide After Sales Service Cleaning Maintenance Material supplied Installation Preliminary assembly instructions Installation dimensions Installation assembly instructions Description and use of hood 10 12 13 Important safety instructions YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provides important safety messages to be read and observed at all times A This is the attention symbol relevant to safety warning of potential risks to the user and to others All safety warnings are preceded by the attention symbol and the following words Ay DANGER Indicates a hazardous situation which if not avoided will cause serious injury A WARNING Indicates a hazardous situation which if not avoided could cause serious injury All the safety messages specify the potential danger warning to which they refer and indicate how to reduce the risk of injury damage and electric shock resulting from incorrect use of the appliance Carefully observe the following instructions e Installation must be carried out at least by a specialised technician in compliance with the manufacturer s instructions and the current local safety regulations Do not repair or replace any part of the appli
7. ance must be taken into account CONNECTION TO THE POWER SUPPLY Make sure the voltage specified on the product s dataplate is the same as the mains voltage The dataplate is located inside the hood and can be e For further information on the treatment recovery and recycling of this appliance contact the competent local authority the household waste collection service or the shop where you purchased the appliance KEEP THESE INSTRUCTIONS seen on removing the grease filter The power cable HO5 VV F type must only be replaced by qualified personnel Contact an authorised Service Centre If provided with a plug connect the appliance to a socket complying with the current regulations and located in an accessible area If it does not have a plug direct connection to the power supply or if the socket is not in an accessible place fit an approved double pole switch that ensures complete disconnection from the power supply in category Ill overvoltage conditions complying with the installation rules GENERAL RECOMMENDATIONS Before use Remove cardboard protection pieces protective film and stickers from accessories Make sure the hood has not been damaged during transport During use Do not expose the appliance to atmospheric agents Advice on safeguarding the environment Packing disposal The packing materials are 100 recyclable and are marked with the recycling symbol The various parts of the packing must
8. ance unless specifically indicated in the user manual e The specialised technician can determine the appropriate extractor hood exhaust air ducting and fixing Fixing must be suitable for the weight of the hood and the load e The appliances are designed for installation flush with the ceiling e The appliance must be disconnected from the power supply before carrying out any installation work e Earthing of the appliance is compulsory Not necessary for class II hoods identified by the symbol ol on the dataplate The power cable must be long enough for connecting the appliance to the power socket Do not pull the power cable to unplug the appliance e The electrical components must not be accessible to the user after installation e Do not touch the appliance with wet parts of the body and do not use it when barefoot The appliance is not intended for use by people including children with limited physical sensory or mental abilities or without experience or knowledge of it unless they are supervised or instructed in its use by someone responsible for their safety Do not repair or replace any part of the appliance unless specifically indicated in the manual Faulty parts must be replaced with original ones All other maintenance services must be carried out by a specialised technician Children must be watched over to ensure they do not play with the appliance When drilling the wall or ceiling be ca
9. e hood without lamps correctly installed risk of electric shock e Wear work gloves for all installation and maintenance operations e The product is not suitable for outdoor use e When the hob is in use the accessible parts of the hood can become hot Disposal of electrical appliances e This appliance is manufactured with recyclable or reusable materials Scrap it in accordance with the local waste disposal regulations Before scrapping make it unusable by cutting off the power cable Installation After unpacking the appliance check for any damage caused during transport In case of problems contact the dealer or the After Sales Service To avoid possible damage it is advisable to remove the appliance from the polystyrene base only before installation PREPARATION FOR INSTALLATION Ay WARNING Very heavy product hood handling and installation must be carried out by at least three people The distance between the support surface of the cooking device and the lowest part of the hood must not be less than 100 cm irrespective of the type of hob electric vitroceramic induction or gas The following nominal power stresses kW must not be exceeded above the gas cooking points Max power of a single cooking point 4 2 kW Max power of hob 16 2 kW Before installation also check the distances specified in the hob manual If the cooking device installation instructions specify a greater distance this dist
10. e needed contact an authorised Service Centre to ensure that only original spare parts are used and that repairs are carried out correctly e Use specific detergents to clean the appliance and follow the manufacturer s instructions e The remote control must only be cleaned with a damp cloth IMPORTANT Failure to observe the instructions for cleaning the hood and replacing the filters involves the risk of fire Therefore make sure to follow the instructions The manufacturer declines any liability for damage to the motor fires caused by inadequate maintenance or failure to comply with the above instructions Maintenance Ay WARNING e Use protective gloves e Disconnect the appliance from the power supply GREASE FILTER Its purpose is to retain the particles of grease produced by cooking It must be cleaned every 14 days or after 15 hours of operation when the LED on the appliance signals this need Use gentle and non aggressive detergents clean it by hand or in a dishwasher at low temperature and with a short cycle To be able to clean the filters pull the hood extraction panel downwards a little with both hands The extraction panel is released and by means of the cylindrical actuator gradually turned downwards allowing removing of the grease filters fixed to the main body of the hood After washing refit the grease filters and lower the extraction panel in its original position of normal operation
11. emove the old batteries and replace them with new ones of the same type then refit the cover IMPORTANT The maximum operating range of the remote control is 5 m Operation by means of switch located on the hood under the extraction panel e Switch to LEFT switches the light on or off e Switch to RIGHT Increases or decreases the external motor extraction power according to the sequence OFF gt 1 2 3 2 1 2 Keep it pressed for 3 seconds to switch the hood off Grease Filter saturation signalling Every 15 hours of use or after 14 days the hood signals the need to service the grease filters The signalling is displayed by lighting up of the corresponding red LED on the main body of the hood Grease filter signalling reset after servicing the grease filters as described in the Maintenance section keep the switch under the hood extraction panel pressed to the RIGHT for 5 seconds until the red LED goes off LED display on the main body of the hood Hood operation status is signalled by LEDs on the appliance ON OFF Gradual stop Green LED 2 Level I Green LED 3 Level 2 Green LED 4 Level 3 Green LED 5 Intense level Green LED 6 Filter saturation display Red LED LED I Display of hood operation status ON OFF LED blinks if the hood timed deactivation function is activated LED 2 Motor LOW power power level LED 3 Motor MEDIUM power power level 2 LED 4 Motor HIGH power power level 3
12. model has six control buttons Button I Switches the hood on or off When the hood is switched on the external motor is set to extraction power Button 2 Increases the extraction power I 2 3 The speed is displayed by lighting up of the LED of the corresponding speed Button 2 has no effect on hood deactivation activation Button 3 Decreases the extraction power 3 gt 2 gt 1 The speed is displayed by lighting up of the LED of the corresponding speed Button 3 has no effect on hood deactivation activation Button 4 Activates timed hood deactivation This function provides for a speed decrease from power level 3 to level maintained for 15 minutes before the hood switches off During timed operation the corresponding LED blinks Button 5 Increases the extraction power to maximum and then automatically returns to power level 3 after 5 minutes The speed is displayed by lighting up of the LED of the corresponding speed Button 6 Switches the light on or off The light intensity becomes adjustable by keeping Button 6 pressed longer 0O KitchenAid e Battery Compartment The battery compartment is located in the back of the remote control Only use CR2032 3V lithium batteries Replacing the batteries the battery compartment cover is located on the back of the remote control Lift it with thumb and forefinger until separating the magnetic contact keeping the cover closed R
13. nd can be positioned anywhere in the house and not necessarily in the kitchen The maximum recommended length of the exhaust pipe connecting the motor to the hood is 6 m In case of elbows in the path established for the evacuation pipe it is advisable to position the motor more than m from them so as not to negatively affect motor efficiency 2 Arrange the installation template supplied on the ceiling and drill the ceiling as indicated The extractor hood must be positioned centrally with respect to the hob IMPORTANT Provide a socket for the electrical connection in an accessible place for hood connection 3 Remove the glass as shown in the figure and remove the grease filters IMPORTANT Provide a suitable support surface on which to place the hood in order to carry out this operation 4 Place the template on the ceiling Mark the positions of the holes for fixing to the ceiling according to the four points provided on the template 5 Make the 10 holes with a suitable drill and insert the plugs supplied A flush with the ceiling Screw the screws supplied in the plugs so that they protrude approx 20 mm from the ceiling B 6 Before hanging the hood on the ceiling make sure the direction of the air outlet connection coincides with the guide arranged for the exhaust duct then screw the connection flange and covering sheet to the hood body IMPORTANT The exhaust air connection can be arranged on any of the side surfaces of the m
14. otor case body To modify the outlet connection direction if already fitted undo the fixing screws of the connection flange and the covering sheet and invert the position 7 Arrange the flexible tube and connect the 200 mm flange to the tube 8 Fix the hood to the ceiling using the washers and nuts supplied IMPORTANT In case of flush ceiling mounting hang the hood on the screws A IMPORTANT In case of suspended hood fixing screw the threaded sleeves supplied on the screws C Cut the threaded rod supplied to the required length and screw it on the threaded sleeves B 9 Connect the hood to the suction tube connected to the external motor Carry out the electrical connection Connect the external motor to the hood with the connection cable IMPORTANT The exhaust air path must be prepared in such a way that the extractor hood can be easily connected The flexible air exhaust tube must be positioned without bends 10 Refit the grease filters and rehook the glass as shown in the figure Description and use of hood Hood body Extraction panel Cylindrical actuator Switch IR sensor Lighting Grease filters LED indicators Anchoring to ceiling OON ADO KRWHNY The hood functions and the external motor performance can be controlled in two alternative ways by means of the remote control or the switch on the main body of the hood Operation using the remote control The 2010 remote control
15. reful not to damage electrical connections and or pipes The ventilation ducts must always discharge to the outside The exhaust air must not be discharged through a duct used to remove fumes produced by appliances running on gas or other fuels but must have an independent outlet All the national regulations on exhausting air must be observed If the hood is used together with other appliances operating on gas or other fuels the negative pressure in the room must not exceed 4 Pa 4 x 10 5 bar Therefore make sure the room is adequately ventilated The Manufacturer declines any liability for improper use or incorrect setting of the controls Regular cleaning and maintenance are essential for correct and efficient operation of the appliance Frequently clean all encrustations from dirty surfaces to prevent the accumulation of grease Regularly remove clean or change the filters Failure to observe the rules for cleaning the hood and cleaning and replacing the filters involves the risk of fire The steam extractor hood must never be opened without the grease filters installed and should be constantly watched over Gas appliances must have pots on them when used under the extractor hood If more than three gas cooking points are used the hood should work at power level 2 or higher This will ensure the elimination of excessive heat in the appliance Make sure the lamps are cold before touching them Do not use or leave th
Download Pdf Manuals
Related Search