Gefen EXT-DVI-1CAT6-GI
Contents
1. INN ee Em oo Oo como BIO SV DC Power DVI Out EQ page 4 Introduction Description 1 Link Connect a CAT 5e cable or better from this port to the Link port on the Sender unit 2 5V DC Connect the included 5V DC power supply to this power receptacle ke v ke 74 o E gt Ei OH 3 Power This LED will glow bright blue once the included 5V DC power supply has been properly connected between the locking power receptacle and an available electrical outlet 4 DVI Out Connect a DVI cable between the imaging system display and the DVI Out port 5 EQ Use this EQ pot to optimize the output signal based on extension distance and cable skew See Adjusting the Signal Quality page 12 for more information 6 Grounding Terminal Connect a grounding wire from this terminal to an approved Earth ground The grounding wire should not be less than 16 AWG page 5 Installation Connection Instructions 1 Connect the included DVI cable from the imaging source e g camera to the DVI In port on the Sender unit Getting Started 2 Connect a DVI cable from the DVI Out port on the Receiver unit to a video scaler or high resolution imaging display 3 Connect a single CAT 5e or better cable from the Link jack on the Sender unit to the Link jack on the Receiver unit 4 Connect a ground wire from the grounding terminals2. on both the Sender and Receiver unit to an approved Earth ground The ground wire should not be less than 16 AWG 5 Use the included locking power supplies to connect the Sender and Receiver unit to available electrical outlets Do not overtighten the locking power connectors Sample Wiring Diagram Galvanically Isolated IGEFEN en DVI CABLE m Receiver DVI Source q 6 such as a Medical Imaging Camera Sender DVI Display EXT DVI 1CAT6 GI page 6 DVI over 1 CAT6 w Galvanic Isolator a Basic Operation DIP Switch Configuration EE 10 teller 10 EDID Management aa oa E 11 11 CO a RARE RE RR Adjustingithe Site ne Mer 12 Basic Operation DIP Switch Configuration On the bottom panel of the Sender unit is a bank of 4 DIP switches Remove the piece of colored tape to reveal the DIP switch bank These DIP switches provide control over EDID management and color depth DIP switches 3 and 4 are not used I Default Settings The following table lists the default factory settings of each DIP switch See the following page for details on each DIP switch function DIP Switch Description 1 ON Uses pass through downstream EDID mode 2 OFF Deep color is disabled page 10 E o gt L o e E N D DIP Switch Configuration E
3. DID Management The DVI over 1 CAT6 w Galvanic Isolator can be switched between two EDID modes Internal or Pass through After changing DIP switch 1 the Sender unit must be power cycled for changes to take effect DIP Switch 1 Description ON Pass through mode DDC and HPD are default passed through Both the connection status and the full video capabilities of the monitor are passed to the source device OFF Internal EDID mode In this mode a generic EDID will be sent to the source device This setting is useful when sufficient EDID data is unavailable from the display device or EDID related problems are encountered Color Management This feature is used to control the color depth for resolutions up to 1080i By default the color depth is set to 8 bit Ifthe output resolution is 1080p or if DIP switch 1 is ON then this DIP switch setting has no effect DIP Switch 2 Description OFF Disables Deep Color support on the output default display device ON Enables Deep Color 12 bit support on the output display device page 11 Adjusting the Signal QUAY The Receiver unit of the DVI over 1 CAT6 w Galvanic Isolator has a trim pot that is used to equalize the output signal compensating for extension distance and cable skew If there is no output video or if output video contains video artifacts and or video noise such as snow use the steps below to adjust the trim pot Basic Operation 1 Use a sma
4. GEFEN DVI over 1 CAT6 w Galvanic Isolator EX DVIICATO GI User Manual Release A2 Important Safety Instructions 10 11 12 13 14 15 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this product near water Clean only with a dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions Do not install or place this product near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachments accessories specified by the manufacturer To reduce the risk of electric shock and or damage to this product never handle or touch this unit or power cord if your hands are wet or damp Do not expose this product to rain or moisture Unplug this apparatus during lightning storms or whe
5. RR O o GS BELL RE 2 Receiverunit ee A Installation EE 6 Con SEN l of die EE ee 6 Introduction 2 Sender unit E 2 O 5 O PIA si a O Gefen O O O DVI G over 1 CATG O w Galvanic Isolator S T oe O O Oo cm SV DC Power DVI In page 2 Introduction Description 1 Link Connect a CAT 5e cable or better from this port to the Link port on the Receiver unit 2 5V DC Connect the included 5V DC power supply to this power receptacle ke v ke 74 o gt Ei 3 Power This LED will glow bright blue once the included 5V DC power supply has been properly connected between the locking power receptacle and an available electrical outlet 4 DVI In Connect the included DVI cable between the imaging source e g imaging camera and the DVI In port 5 Grounding Terminal Connect a grounding wire from this terminal to an approved Earth ground The grounding wire should not be less than 16 AWG page 3 ko E gs wn o E E oO Introduction Receiver unit EXT DVI 1CATS GIR Gefen Link O Gefen O DVI G over 1 CATG O w Galvanic Isolator R
6. der to claim warranty Customers outside the US are responsible for shipping charges to and from Gefen Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com Contacting Gefen Tecnicas Technical Support 818 772 9100 800 545 6900 8 00 AM to 5 00 PM Monday Friday Pacific Time Fax 818 772 9120 Email support gefen com Web http www gefen com Mailing Address Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 Product Registration Register your product here http www gefen com kvm Registry Registration jsp Operating Notes Always connect a bonding wire between an approved safety ground and the grounding screw on the chassis Electromagnetic Interference This product is s
7. ll flat headed tool to turn the EQ pot 2 The trim pot has eight different positions 0 through 7 Turn the trim pot in a clockwise direction until it clicks to the next position The arrow indicator on the trim pot will indicate the current position 3 Check the image 4 If necessary continue adjusting the rotary switch until the issue is resolved 5V DC Power Information page 12 DVI over 1 CAT6 w Galvanic Isolator EZ Appendix Surface Mounting Instructions The Sender and Receiver units can be mounted on any flat surface as shown below screws not included There should be an inch or two of clearance between the edges of the unit and any walls or vertical surfaces to allow for enough clearance for connection and disconnection of the DVI cables Appendix For installation on a drywall surface use a 6 drywall screw When installing it is recommended to use the center hole on a stud page 16 5 Kl E o a lt Specifications Connectors amp Indicators Video Input Sender Video Output Receiver Link Sender Receiver Power Sender Receiver Power Indicator Sender Receiver EDID Selector Sender Deep Color Selector Sender EQ Adjustment Receiver 1x DVI 29 pin female digital only O 1x DVI 29 pin female digital only 1 x RJ 45 gt 1 x Locking type 1 x LED blue 1 x DIP switch 1 x DIP switch 1 x 8 position rota
8. n unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Batteries that may be included with this product and or accessories should never be exposed to open flame or excessive heat Always dispose of used batteries according to the instructions Warranty Information Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in or
9. pment Supports resolutions up to 1080p Full HD and 1920 x 1200 WUXGA HDCP pass through Switchable Deep Color support HPD pass through EDID management switch for rapid integration of source and display EQ adjustment 8 position switch for cable skew compensation Secure grounding terminals on both Sender and Receiver units Locking power supply connectors Surface mountable d HDCP A LU COMPLIANT Packing List The DVI over 1 CAT6 w Galvanic Isolator ships with the items listed below If any of these items are not present in the box when you first open it immediately contact your dealer or Gefen 1 x DVI over 1 CAT6 w Galvanic Isolator Sender unit 1 x DVI over 1 CAT6 w Galvanic Isolator Receiver unit 1 x 6 ft Dual Link DVI cable 2 x 5V DC Power Supples 1 x Quick Start Guide vi Table of Contas Getting Started Introduction ER DDR REAR RR RR Eee 2 Sonder D E E 2 ET VE 4 Installation 6 Connection InStrUCtIONS siii ita 6 sample Wiring Diagram soci era is 6 2 Basic Operation RUSS eet TEE 10 Default Settings nee He he 10 EDID Management ciioipinrii astecas taco ga agitar EENS siga 11 ColoriManagement isentas esti is 11 Adjusting the Signal Quality 12 3 Appendix Surface Mounting Instruttons inmi iia ET 16 Specific OS ET 17 viii DVI over 1 CAT6 w Galvanic Isolator 1 Getting Started INtRODUCHOMN BEE 2 Sendern arr a wae aye DARDO
10. ry switch Operational Maximum Pixel Clock Power Input Power Consumption Sender Receiver Storage Temperature Relative Humidity Atmospheric Pressure Operating Temperature MTBF Physical 165 MHz DV DC 4 Watts ea max 4 F 158 F 20 C 70 C Environmental 10 to 90 non condensing Operating 10 to 80 non condensing Environmental 7 25 Ibf in to 15 4 Ibf in 50 kPa to 106 kPa Operating 11 Ibf in to 15 4 Ibf in 76 kPa to 106 kPa 41 to 104 F 5 to 40 C 50000 Hours Dimensions W x H x D Sender Receiver Unit Weight each 5 6 x 1 1 x 3 4 143mm x 28mm x 86mm 0 4 Ib 0 18 kg page 17
11. ubject to the following two conditions b This device may not cause harmful interference b This device must accept any interference received including interference that may cause undesired operation Use only the AC DC adapter supplied by the manufacturer hd Do not install or use this product in an environment where it is difficult to connect or disconnect the AC DC adapter No modifications of this equipment is allowed Do not dispose of this product in the trash Contact you local waste authority for assistance This product is fully compliant to the RoHS directive This product meets the requirements of the applicable EC directives This product cannot be disposed of in the general trash TUV certified product Read the User Manual DVI over 1 CAT6 w Galvanic Isolator is a trademark of Gefen LLC O 2014 Gefen LLC All Rights Reserved All trademarks are the property of their respective owners Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice O X Ce O O This product uses UL or CE listed power supplies Features and Packing List Features Compliant with Medical Standards EN60601 1 and EN60601 1 2 3rd Edition Extends DVI up to 132 feet 40 meters over CAT 6a Extends DVI up to 100 feet 30 meters over CAT 5e Provides up to 5kV galvanic isolation between the source and the downstream equi
Download Pdf Manuals
Related Search