Cambridge Audio Topaz AM10
Contents
1. Turntable Operating instructions After making any connections to your unit activate the Topaz AM10 by pressing the On Off button on the front of the unit Setting the source Press the Source button on the front of the unit corresponding to your desired source Alternatively you may use the appropriate button on the remote control MP3 Aux Adjusting the volume Use either the Volume Up Down buttons on the remote control or the Volume control on the front of your unit system to change the volume level The newly selected level will be indicated briefly on the front display The volume is displayed in minus dB where OdB is the highest level A progressively larger negative number indicates the volume is being reduced Adjusting the audio settings Adjustments to the bass treble and balance can be made as follows 1 To enter the audio menu Press either the Menu button on the front of the unit or on the remote control 2 Step through the available settings by pressing the Menu button The settings available are in order Bass Treble and Balance 3 When you wish to make an adjustment for bass treble or balance simply rotate the Volume control or use the Volume control buttons on the remote control 4 To exit wait for five seconds until the unit returns to normal mode Topa2. The wire which is coloured BROWN must be BLUE connected to the terminal which is marked N with the letter L or coloured RED The wire which is coloured GREEN YELLOW must be connected to the terminal which is marked with the letter E or coloured GREEN If a 13 amp BS 1363 plug is used a 3 amp fuse must be fitted or if any other type of plug is used a 3 amp fuse must be fitted either in the plug or adaptor or on the distribution board Topaz AM10 Rear panel connections x a l 2 AN T Power ACau TTL a OQ N gt T Left si A A e gt 2 a 1 E Right Rated Power Consumption 260W i MP3 Aux co Tuner DAB Phono BD DVD Rec Out L 6 Loudspeaker Terminals Impedaps 448 ohms 2 3 4 2 Audio inputs These inputs are suitable for any line level source equipment such as the audio outputs of CD players BD DVD players etc 2 Phono input This input has a built in phono stage Record players fitted with Phono Cartridges of the Moving Magnet MM or high output Moving Coil MC type between 2 6mV output and 30 50k load impedance can be used Low output Moving Coil types lt 1mV and usually 10 1000 ohm load impedance cannot be directly connected and will require a matching transformer or head amp Please consult your dealer for details Note The Ground terminals on both th
3. Topaz AM10 ENGLISH CD5 CD10 Prog Clear Uk m o Random Repeat Remain A v w wea au Phono 6 Cambridge Audio Cambridge Audio Connections Loudspeakers Check the impedance of your speakers When using a pair of speakers you can use types with an impedance of between 4 and 8 Ohms The red coloured speaker terminals are positive and the black speaker terminals are negative Make sure correct polarity is maintained at each speaker connector or the sound can become weak and phasey with little bass Using bare wire connections Prepare the speaker cords for connection by stripping off approximately 10mm 3 8 or less of the outer insulation More than 10mm could cause a short circuit Twist the wires tightly together so there are no loose ends Unscrew the speaker terminal insert the speaker cable tighten the terminal and secure the cable Right speaker Black gt yf Note All connections are made using standard loudspeaker cable Basic connection The diagram below shows the basic connection of your unit to a CD player and a turntable and a pair of loudspeakers Left speaker AM10 IO 0 61 CD player
4. Topaz AM10 Cambridge Audio Your music our passion Cambridge Audio Contents Introduction Important safety instructions Limit d Wara usisissanninkinisiisisisistioninkiisikania ski tiki iii Rear PANG COKHECUDNS skinasi ii ai i E ER Ad ke HERR ETR KE KER LE di KAR Fort Pate COMING cas K 4l ic ristan ki dilan n AT Remote control Connections Operating instru CU OINS Dr a i Technical SpeCifi a ti0 S8 iii xi xa kl lakl k nn asis niainie k sias ossis ii Troubleshooting Introduction Thank you for purchasing this Cambridge Audio Topaz AM10 Amplifier We are confident that you will enjoy many years of listening pleasure from it Like all Cambridge Audio products the AM10 adheres to our three core principles stunning performance ease of use and incredible value The unit can support a wide range of external sources and a front panel MP3 Portable Media Player input has been fitted which can be used with the headphone or line level outputs of most portable players The supplied remote control can control this unit plus the matching CD5 or CD10 CD players if required Part of our new Topaz range this product also features a new casework design with braced front panel rigid wrap over lid assembly and carefully designed mechanicals for resonance control Your amplifier can only be as good as the system it is connected to Please do not compromise on the q
5. BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL PURPOSE Some countries and US states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you specific legal rights and you may have other statutory rights which vary from state to state or country to country For any service in or out of warranty please contact your dealer Plug Fitting Instructions UK Only The cord supplied with this appliance is factory fitted with a UK mains plug fitted with a 3 amp fuse inside If it is necessary to change the fuse it is important that a3 amp one is used If the plug needs to be changed because it is not suitable for your socket or becomes damaged it should be cut off and an appropriate plug fitted following the wiring instructions below The plug must then be disposed of safely as insertion into a mains socket is likely to cause an electrical hazard Should it be necessary to fit a 3 pin BS mains plug to the power cord the wires should be fitted as shown in this diagram The colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug Connect them as follows The wire which is coloured BLUE must be GREEN E connected to the terminal which is marked YELLOW with the letter N or coloured BLACK FUSE
6. the authorised dealer from whom you purchased this product for more information CE mark This product complies with European Low Voltage 2006 95 EC Electromagnetic Compatibility 2004 108 EC and Environmentally friendly design of Energy related Products 2009 125 EC Directives when used and installed according to this instruction manual For continued compliance only Cambridge Audio accessories should be used with this product and servicing must be referred to qualified service personnel C Tick mark This product meets the Australian Communications Authority s Radio communications and EMC requirements Pe Ross Test Stamp This product meets Russian electronic safety approvals FCC regulations NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT SUCH MODIFICATIONS COULD VOID THE USER AUTHORITY TO OPERATE THE EQUIPMENT This equipment has been tested and found to comply with the FC limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installat
7. ded Note Plugging in headphones will automatically mute the loudspeaker outputs 3 Infrared sensor Receives IR commands from the supplied remote control An unobstructed line of sight between the remote control and the sensor is required 4 MP3 input socket This source input allows you to connect a portable audio device such as an MP3 player directly into the front of the unit using a 3 5mm stereo jack Once plugged in this input is automatically selected although other inputs can still be selected once a stereo jack is plugged in The MP3 AUX button on the front of the unit will select this input whilst a stereo jack is plugged in Note Plugging a source into the front panel MP3 input overrides the Aux input Simply remove the jack from the front panel to automatically re enable the Aux input Also note that as the output level of MP3 players tends to be quite low the AM10 adds 10dB to the current volume setting when and only when the MP3 input is selected 5 Input source buttons MP3 Aux CD Tuner DAB Phono BD DVD Press the relevant source button to select the desired input source 6 Display Used to display information such as the selected input source volume and tone balance levels Note When first purchased the display will have a protective film over the top Peel this off for a clear display Menu button Pressing this once will select the Bass option Pressing a second time will s
8. e record player and the AM10 should be connected where possible with a ground wire for lowest noise hum pickup 3 Rec Out Connect to the recording input of a tape deck CD recorder input etc 4 Loudspeaker terminals Connect the wires from your left channel loudspeaker to the Left positive and negative terminals and the wires from the right channel loudspeaker to the Right positive and negative terminals In each case the red terminal is the positive output and the black terminal is the negative output Care should be taken to ensure no stray strands of wire are shorting speaker outputs together Please ensure that the loudspeaker terminals have been tightened adequately to provide a good electrical connection It is possible for the sound quality to be affected if the screw terminals are loose 5 Voltage select switch For servicing use only 6 AC power socket Once all connections are complete plug the AC power cable into an appropriate mains socket and turn the unit on Cambridge Audio Front panel controls Cambridge Audio XQ O e O 8 886 2 MP3 Aux i N O 2 6 Phono 5 O BD DVD To paz AM10 Integrated Amplifier 1 Power On Off Switches the unit on or off 2 Headphones socket Allows for the connection of stereo headphones with a inch jack plug Headphones with an impedance of between 32 and 600 ohms are recommen
9. elect the Treble option and pressing a third time will select the Balance option When one of these options is selected the volume control will adjust the level If nothing is pressed for a while the source will be displayed and the volume control will go back to controlling the volume level Volume control Use to increase or decrease the level of the sound from the outputs of the unit This controls the volume level of the loudspeakers and headphones It does not affect the level of the Rec Out output The volume control will also change the level of bass treble and balance in the menu options Remote control The Topaz AM10 is supplied with a remote control that operates this unit and its built in tuner In addition the buttons with Blue coloured icons can operate a matching Topaz CD5 or CD10 player Always use Alkaline batteries CD5 CD10 Blue coloured icons To operate the Topaz CD5 or CD10 players only For more information refer to the Topaz CD5 and CD10 user s manual X Mute Mutes audio on the unit Press again to cancel mute 2 Volume Increases or decreases the volume of the unit Also used to change the bass treble and balance settings when these are selected Menu Toggles between Bass Treble and Balance options Use the volume buttons to change the level of the selected option Source buttons CD Tuner BD DVD MP3 Aux Phono Press the relevant button to select the desired music source
10. ion If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help AM10 x 2 l o Z W Cambridge Audio Ventilation IMPORTANT The unit will become hot when in use Do not stack multiple units on top of each other Do not place in an enclosed area such as a bookcase or in a cabinet without sufficient ventilation Ensure that small objects do not fall through any ventilation grille If this happens switch off immediately disconnect from the mains supply and contact your dealer for advice Positioning Choose the installation location carefully Avoid placing it in direct sunlight or close to a source of heat No naked flame sources such as lighted candles should be placed on the unit Also avoid locations subject to vibration and excessive dust cold or moisture The unit can be used in a moderate climate This unit must be installed on a sturdy level surface Do not place in a sealed area such as a bookcase or in a cabinet Do not place the unit on an
11. is blocking the remote sensor In the event that the above solutions do not remedy your problem please consult our frequently asked questions FAQ section on our website www cambridge audio com sts faqs For all servicing in or out of warranty please contact your dealer Cambridge Audio is a brand of Audio Partnership Plc Registered Office Gallery Court Hankey Place London SE1 4BB United Kingdom Registered in England No 2953313 www cambridge audio com 69 2010 Cambridge Audio Ltd S 2 o D N a lt
12. le or receipted invoice which is evidence that this product is within the warranty period must be presented to obtain warranty service This Warranty is invalid if a the factory applied serial number has been altered or removed from this product or b this product was not purchased from a Cambridge Audio authorised dealer You may call Cambridge Audio or your local country Cambridge Audio distributor to confirm that you have an unaltered serial number and or you purchased from a Cambridge Audio authorised dealer This Warranty does not cover cosmetic damage or damage due to acts of God accident misuse abuse negligence commercial use or modification of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or installation or attempted repair by anyone other than Cambridge Audio or a Cambridge Audio dealer or authorised service agent which is authorised to do Cambridge Audio warranty work Any unauthorised repairs will void this Warranty This Warranty does not cover products sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER CAMBRIDGE AUDIO SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY IN THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER INCLUDING
13. n aerosol at or near the unit Battery disposal Please dispose of any discharged batteries according to local environmental electronic waste disposal guidelines Loudspeakers Before making any connections to loudspeakers make sure all power is turned off and only use suitable interconnects Servicing These units are not user serviceable never attempt to repair disassemble or reconstruct the unit if there seems to be a problem A serious electric shock could result if this precautionary measure is ignored In the event of a problem or failure please contact your dealer Limited warranty Cambridge Audio warrants this product to be free from defects in materials and workmanship subject to the terms set forth below Cambridge Audio will repair or replace at Cambridge Audio s option this product or any defective parts in this product Warranty periods may vary from country to country If in doubt consult your dealer and ensure that you retain proof of purchase To obtain warranty service please contact the Cambridge Audio authorised dealer from which you purchased this product If your dealer is not equipped to perform the repair of your Cambridge Audio product it can be returned by your dealer to Cambridge Audio or an authorised Cambridge Audio service agent You will need to ship this product in either its original packaging or packaging affording an equal degree of protection Proof of purchase in the form of a bill of sa
14. pod bracket or table specified by the manufacturer or sold with the apparatus h When a cart is used use caution when moving the cart 3 apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as the power supply cord or plug having been damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped WARNING To reduce the risk of fire or electric shock do not expose this unit to rain or moisture Batteries battery pack or batteries installed shall not be exposed to excessive heat such as sunshine fire or the like The unit is of Class 1 construction and must be connected to a mains socket outlet with a protective earthing connection The unit must be installed in a manner that makes disconnection of the mains plug from the mains socket outlet or appliance connector from the rear of the unit possible Where the mains plug is used as the disconnect device the disconnect device shall remain readily operable Only use the mains cord supplied with this unit Please ensure there is ample ventilation We recommend that you do not place the unit in an enclosed space if you wish to place the unit on a
15. shelf use the top shelf to allow maximum ventilation Do not put any objects on top of this unit Do not situate it on a rug or other soft surface and do not obstruct any air inlets or outlet grilles Do not cover the ventilation grilles with items such as newspapers tablecloths curtains etc This unit must not be used near water or exposed to dripping or splashing water or other liquids No objects filled with liquid such as vases shall be placed on the unit Topaz Risk of electric Risque de choc Vorm ffnen shock electrique Do not open des ger tes Ne pas ouvrir Netzstecker ziehen L ESIR EA The lightning flash with the arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the service literature relevant to this appliance WEEE symbol The crossed out wheeled bin is the European Union symbol for z indicating separate collection for electrical and electronic equipment This product contains electrical and electronic equipment which should be reused recycled or recovered and should not be disposed of with unsorted regular waste Please return the unit or contact
16. td 2010 W Ra ak sa da du az ek da Gi Sk a d dak Gar k d k en nt ja qez a kr dibi W Important safety instructions For your own safety please read the following important safety instructions carefully before attempting to connect this unit to the mains power supply They will also enable you to get the best performance from and prolong the life of the unit 1 Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with a dry cloth NOof WN Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use with only the cart stand tri
17. uality of your source equipment speakers or cabling Naturally we particularly recommend source and speaker models from the Cambridge Audio range which have been designed to the same exacting standards as this product Your dealer can also supply excellent quality Cambridge Audio interconnects to ensure your system realises its full potential Thank you for taking the time to read this manual we recommend you keep it for future reference Mat ba Matthew Bramble Cambridge Audio Technical Director and the AM10 design team Make sure you register your purchase Visit www cambridge audio com sts By registering you ll be the first to know about e Future product releases e Software upgrades e News events and exclusive offers plus competitions This guide is designed to make installing and using this product as easy as possible Information in this document has been carefully checked for accuracy at the time of printing however Cambridge Audio s policy is one of continuous improvement therefore design and specifications are subject to change without prior notice This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer All trademarks and registered trademarks are the property of their respective owners Copyright Cambridge Audio L
18. unstable surface or shelf The unit may fall causing serious injury to a child or adult as well as serious damage to the product Do not place other equipment on top of the unit Due to stray magnetic fields turntables or CRT TVs should not be located nearby due to possible interference Electronic audio components have a running in period of around a week if used several hours per day This will allow the new components to settle down the sonic properties will improve over this time Power sources The unit should be operated only from the type of power source indicated on the marking label If you are not sure of the type of power supply to your home consult your product dealer or local power company To turn the unit off switch off at the front panel If you do not intend to use this unit for a long period of time unplug it from the mains socket Overloading Do not overload wall outlets or extension cord as this can result in a risk of fire or electric shock Overloaded AC outlets extension cords frayed power cords damaged or cracked wire insulation and broken plugs are dangerous They may result in a shock or fire hazard Be sure to insert each power cord securely To prevent hum and noise do not bundle the interconnect leads with the power cord or speaker leads Cleaning To clean the unit wipe its case with a dry lint free cloth Do not use any cleaning fluids containing alcohol ammonia or abrasives Do not spray a
19. z AM10 Technical specifications Power output THD unweighted 35 watts into 8Q lt 0 01 1kHz 80 of rated power lt 0 15 20Hz 20kHz 80 of rated power ENGLISH Frequency response 3dB 5Hz 50kHz S N ratio ref 1W gt 82dB unweighted Input impedances 47k ohms Power Amp damping factor gt 50 Max power consumption 260W Bass Treble controls Shelving ultimate boost cut 10dB 100Hz and 10kHz Dimensions 76 x 430 x 340mm 3 0 x 16 9 x 13 4 Weight 5 6kg 12 3lbs Troubleshooting There is no power Ensure the AC power cord is connected securely Ensure the plug is fully inserted into the wall socket and is switched on Check fuse in the mains plug or adaptor Check the power is on at the front of the unit There is no sound Check the correct input is selected Check that the speakers are connected correctly Check the unit is not in mute mode The sound is distorted Check speaker connections There is a hum coming from the speaker Ensure that all cable connections are secure particularly ground shield connections for turntables There is unwanted background noise and interference Move the unit away from other electrical eguipment that is likely to cause interference Ensure that all cable connections are secure particularly ground shield connections for turntables The remote handset will not function Check that the batteries have not expired Ensure that nothing
Download Pdf Manuals
Related Search