Jura IMPRESSA XJ9 Professional
Contents
1. 13 1 Preparing and using for the first time Adjusting the grinder You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee CAUTION If you adjust the consistency of grind when the grinder is not ope rating the grinder adjustment switch could be damaged gt Only adjust the consistency of grind when the grinder is run ning The consistency of grind is correct if the coffee flows regularly from the coffee spout In addition a fine thick crema forms Example Proceed as follows to change the consistency of grind during the preparation of an espresso gt Open the storage compartment cover gt Place a cup under the coffee spout gt Press the Espresso button The grinder starts up Espresso is displayed gt Turn the grinder adjustment switch to the desired position while the grinder is running The espresso is prepared and the consistency of grind is adjusted gt Close the storage compartment cover Connecting milk Your IMPRESSA creates fine creamy feather light milk foam with a perfect consistency The most important requirement for frothing milk is a milk temperature of 4 8 C We would therefore recom mend using a milk cooler gt Attach the milk pipe to the cappuccino frother To do this attach the end of the milk pipe to the connector on the left hand side of the cappuccino frother gt Connect the other end of the m2. IMPRESSA X 9 Professional Instructions tor Use Original instructions for use il Before using the machine read the instructions for use Checked documentation comprehensible complete amp safe The Instructions for use has been awarded the seal of approval by the independent German Technical Inspection Agency TUV SUD due to its easy to understand style its thoroughness and coverage of safety aspects JURA Type 683 Table of contents Your IMPRESSA XJ9 Professional Control elements Important information 1 BO et U E EE E E A FOO E E E E E E T Preparing and using for the first time IAE E e a E ren Urn tea etree Settings by the JURA Service technician sssessessssessessersersseossesserssrossensersersneossesserssrossesserserssrosseeseresre STR TU TN a PC I We nce cetera E ey ce E E ses E A A EE E counters FUMING TINS WATE CAN IK sassssscicacetatannsisenenredernennsbacaibioancdicionsithiesdessyesus A i ee aenor EE EE ESSA OMAN ce serroctoces xed AIE A encod E E A E actiataiod SUNG ag U en ee A ne ee Determining the water hardness ii cisconseenasscasesnazcscstuavil tds asisslasiiaunanuidscateasuansieounsliadeasiatbialesenieuchddiananes PSTD TS UT NVM or E state achieve vote eben anviceenccneseu hs arctan A coscaenecsen pave E Connie una TANI aee ee aeece cence og cance de E EEE ENE E E Preparation Ways Of preparing a DEVE dG C enpren eaa eaea EEE aL N Erea S EDE a O O E a E E en aa ee Preparing two
3. 25 ml 240 ml Portion of milk 3 sec 120 sec Hot water Low Normal 25 ml 450 ml X high Example Proceed as follows to change the amount of milk for a latte macchiato from 16 sec to 20 sec the interval from 30 sec to 40 sec and the amount of water from 45 ml to 40 ml Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Product settings 2 6 is displayed gt Press the Expert mode button Expert mode m e Next select the button of the product for which you would like to make settings No product is prepared at this point gt Press the Latte macchiato button Latte macchiato gt Press the Amount of milk Dutton gt Press the lt or gt button to change setting for the amount of milk to 20 sec gt Press the Save button Saved appears briefly on the display 25 4 Permanent settings in programming mode gt Press the Volume button gt Press the lt or gt button to change setting for the fill volume to 40 ml gt Press the Save button Saved appears briefly on the display Press the Next button Press the Interval button v vy v Press the lt or gt button to cha
4. Machine settings 4 6 P gt Press the P button to exit programming mode Please select product 31 4 Permanent settings in programming mode Restore factory settings In the programme item Machine settings 4 6 Factory setting you can reset various settings to their factory settings m Machine All user settings apart from the filter and water hardness are reset to factory settings Your IMPRESSA then switches off m Product The settings amount of water coffee strength temperature etc for any product can be reset individually to the factory settings The corresponding double product is also reset to the factory settings at the same time m All products The settings amount of water coffee strength temperature etc for all products are reset to the factory settings m Display settings All display settings are reset to the factory settings Example Proceed as follows to reset the values for Espresso to the factory settings Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 4 6 is displayed gt Press the Factory setting button Factory setting gt Press the Product button Product gt Press the Espresso button Espresso Reset this product to the factory setting
5. gt Place a receptacle under the coffee spout gt Press the P button Maintenance status 1 6 gt Press the Rinse the coffee system button Machine is rinsing water flows out of the coffee spout The rinse stops automatically Please select product appears on the display 35 5 Maintenance Rinsing the cappuccino frother Cleaning the cappuccino frother CAUTION 36 After each milk preparation the IMPRESSA prompts you to rinse the milk system Precondition Rinse the milk system is displayed gt Place a receptacle under the cappuccino frother gt Press the Rotary Switch Milk system is being rinsed water flows out of the cappuc cino frother The rinse stops automatically and Please select product appears on the display To ensure that the cappuccino frother always works properly you must clean it daily when you have been preparing milk Your IMPRESSA will not prompt you to clean the cappuccino frother If the wrong cleaning agent is used the machine could be damaged and or traces could be left behind in the water gt Use only original JURA maintenance products i JURA Cappuccino Cleaner is available from specialised dealers Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Press the Clean the milk system button Cleaning agent for milk system v v Po
6. lt or gt button to set the water hardness gt Press the Save button Saved appears briefly on the display Maintenance settings 3 6 P gt Press the P button to exit programming mode Please select product Energy saving mode In the programme item Machine settings 4 6 Save energy you can permanently set an energy saving mode Energy Save Mode E S M m Active Soon after the last preparation the IMPRESSA stops heating up After about 5 minutes the message Energy Save is dis played Before you can prepare a speciality coffee speciality coffee with milk or hot water the machine must heat up m Inactive All speciality coffees speciality coffees with milk and hot water can be prepared without having to wait Example Proceed as follows to change the energy saving mode from Active to Inactive Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 4 6 is displayed gt Press the Save energy button Save energy gt Press the Inactive button gt Press the Save button Saved appears briefly on the display Machine settings 4 6 P gt Press the P button to exit programming mode Please select product 30 Automatic switch off Unit for amount of wat
7. gt Press the Yes button Saved appears briefly on the display Machine P gt Press the P button to exit programming mode Please select product 32 4 Permanent settings in programming mode Language In this programme item you can set the language used by your IMPRESSA i Ifyou choose the wrong language by mistake you can easily reset the machine to English Press the P button to enter pro gramming mode Use the Rotary Switch to select pro gramme item 5 6 and then press the top left hand button Example Proceed as follows to change the language from English to Deutsch Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 5 6 is displayed Press the Choose language button Choose language Press the Deutsch button Gespeichert appears briefly on the display Gerdteeinstellungen 5 67 P gt Press the P button to exit programming mode Bitte w hlen Sie Ihr Produkt v v Background colour In this programme item you can set the background colour for the display of your IMPRESSA Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 5 6 is displayed gt
8. gt Press the t button Information 6 6 Joreset the day counter to zero press the Day counter but ton Then press the t button and confirm by pressing Yes P gt Press the P button to exit programming mode Please select product 34 5 Maintenance 5 Maintenance Your IMPRESSA has the following integrated maintenance program mes m Rinsing the machine Rinse the coffee system m Rinsing the cappuccino frother Rinse the milk system m Cleaning the cappuccino frother Clean the milk system m Changing the filter Change the filter only if filter is activated m Cleaning the machine Clean m Descaling the machine Descale i Clean or descale the machine rinse the milk system or change the filter when you are prompted to do so i Press the P button to view a list of the maintenance program mes Maintenance status 1 6 By referring to the bar you can see which maintenance programme is due When the bar is completely filled with red your IMPRESSA will prompt you to perform the appropriate maintenance programme i The IMPRESSA will not prompt you to clean the milk system In the interests of hygiene you should clean the milk system daily when you have been preparing milk Rinsing the machine You can initiate the rinse operation manually at any time Precondition Please select product is displayed P
9. Press the Colour scheme button Colour scheme gt Press the lt or gt button to change the setting gt Press the Save button Saved appears briefly on the display Machine settings 5 6 33 4 Permanent settings in programming mode P gt Press the P button to exit programming mode Please select product i The selected background colour only applies on the selection page of the display showing the speciality coffees Querying information In the programme item Information 6 6 you can view the fol lowing information m Product counter Number of prepared coffee speciality cof fees speciality coffees with milk and hot water m Maintenance counter Maintenance status and number of maintenance programmes performed cleaning descaling changing the filter m Day counter Number of prepared coffee speciality coffees speciality coffees with milk and hot water This counter can be reset to zero m Version Software version Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Informa tion 6 6 is displayed gt Press the Product counter button The number of speciality coffees prepared is displayed You can also view the number of products prepared in the pro duct selector To do this turn the Rotary Switch
10. Warm milk and milk foam 2 Preparation Your IMPRESSA can prepare a latte macchiato or cappuccino at the touch of a button There is no need to move the glass or cup Example Proceed as follows to prepare one latte macchiato Precondition Please select product is displayed Milk is connected to the cappuccino frother gt Place a glass under the cappuccino frother gt Turn the setting wheel of the cappuccino frother to the Milk Foam position gt Press the Latte macchiato button Latte macchiato the milk foam is prepared Preparation stops automatically when the preset amount of milk is reached There is a short interval while the hot milk separates from the pi e milk foam This allows the typical layers of a latte macchiato to form You can choose the length of this interval in program ming mode see Chapter 4 Permanent settings in program ming mode Product settings Coffee preparation starts The preset amount of water flows into the glass Preparation stops automatically Please select product appears on the display To make sure the cappuccino frother always works properly you must rinse and clean it regularly see Chapter 5 Maintenance Rin sing the cappuccino frother Example Proceed as follows to prepare milk foam Precondition Please select product is displayed Milk is connected to the cappuccino frother gt Place a cup under the cappuccin
11. power supply first switch off the IMPRESSA using the On Off button and then at the power switch Only then should you remove the mains plug from the power socket There is a risk of scalds or burns on the spouts and the cappuccino frother Place the machine out of the reach of children Do not touch any hot parts Use the handles provided Ensure that the cappuccino frother is correctly fitted and clean If incorrectly fitted or if they become blocked the cap puccino frother or its parts might come off A defective machine is not safe and could cause injury or fire To avoid damage and any associated risk of injury or fire Never allow the mains cable to loosely hang down The mains cable could pose a tripping hazard or become damaged Protect the IMPRESSA from environmental influences such as rain frost and direct sunlight Do not immerse the IMPRESSA mains cable or connections in water Do not put the IMPRESSA or any individual parts in the dish washer Switch your IMPRESSA off at the power switch before any cleaning operation Always wipe the IMPRESSA with a damp cloth rather than a wet one and protect it from prolonged exposure to water splash The IMPRESSA is not suitable for installation on a surface where a jet of water can be used The machine must not be cleaned with a jet of water Only connect the machine to the mains voltage in accordance with the information on the rating plate The rating plate is located
12. even easier to use your IMPRESSA Display Control elements Control elements 2 3 4 5 6 7 1 Bean container with aroma preservation cover 2 Water tank cover 3 Water tank 4 Height adjustable cappuccino frother 5 Coffee grounds container 6 Drip tray 7 Cup grille Filler funnel for ground coffee Storage compartment cover Grinder adjustment switch Measuring spoon for ground coffee Hot water nozzle Height and width adjustable coffee spout Control elements 4 5 Top of the machine Front 1 On Off button 4 Display 2 Rotary Switch 5 Buttons button function depends on 3 P P button programming what is shown in the display 3 Back of the machine 1 Power switch 3 Port under cover 2 Mains cable Important information Important information Proper use For your safety This machine is intended for use by specialist or trained staff in busi nesses light industry and agricultural facilities or for commercial use by non professionals It should only be used for coffee preparation and to heat milk and water Use for any other purpose will be deemed improper JURA Elektroapparate AG cannot accept any res ponsibility for the consequences of improper use Before using the machine read these instructions for use thoroughly and completely and comply
13. power switch on the back of the machine gt Press the On Off button to switch the IMPRESSA on The display shows the languages you can choose from C To display more languages press the Next button bottom right me gt Press the button that corresponds to the language you want e g English Saved appears briefly on the display to confirm the setting Filter Now decide whether you want to operate your IMPRESSA with or without a CLARIS Pro Blue filter cartridge m o Activating the filter CAUTION Milk sparkling mineral water or other liquids can damage the water tank or the machine gt Only fill the water tank with fresh cold water gt Press the Active button gt Press the Save button Saved appears briefly on the display Insert filter gt Remove and empty the water tank 11 1 Preparing and using for the first time p e me pi e i Deactivating the filter gt Open the filter holder and insert the filter cartridge into the water tank exerting slight pressure gt Close the filter holder It will click into place audibly After two months the filter will cease to work Set the date on the date plate on the filter holder in the water tank gt Fill the water tank with fresh cold water and reinsert the tank gt Place a receptacle under the cappuccino frother the coffee spout and the hot water nozzle gt Pre
14. specdidlity CON CES spssrtggriscn nunen Aneen ia S E aae AERAN weer ar EEan Late macchiato Capp siiis ne aia EEEE EES ntere ett rare EL el LCT Ie MII E E E O R Ceke ii A E A A E T A A E A ter rrr ar eter er Permanently setting the amount of water for the CUD S Z eeeseesesessssesesessesessssseessseeseeeseseeeeesteess EEE E E E A A E E EIE E E E E E A V E E Daily operation EN OT eE E R E E E A NEA BENAU AE E E E E A T E T E SEE OU cise E N A EN TA E E A PE E N E Permanent settings in programming mode Enabling and disabling programming MOTE s sisien raah aasan anaes POOE E N a eco ana A E E E I E E E O E Enable or disable one off settings scsssscsssscsssscsssscsssecsssscssscssecsssesessecssassessesesassssassesassnsacsecassncaseess Enabling anad disabling Product Selector VIEW i Enabing ana CISADIG PF OCUCUS sedicesima E EAr raai EES E ENa A E A E EEE E T seiting the Water PIANC SS szsuccesinvsvvncnncsehtasabenestbassehtncsnstecdigsubseannnd sthescbbelitbobsledtaestectsedsssosanscosttiaanigscsanes Be I wina MRC agree sec cceeseregces E A toca sence eee ee Automati SUIUCM MON sicncpppatecctca ttcestasoenseacetsatiascanicataytteaceoksiantsistsnesibsaitetoacenctimeas eves NE suena UNICO amount Or WI C eee eee eee ae en cen ee eee eee ER One one ene are Restore factory Sie UMN CS saisir eei aiaa i in aaas ean Er aiia PA VMAS E E A AEE EE E A T T E E E Paeroa DO Ueo a A E a A OEE EE E E A E E E Table of contents 5 Maintenance
15. 3 Latte macchiato 17 Machine Cleaning 40 Descaling 41 Rinsing 35 Setting up 9 Switching off 22 Switching on 21 Mains cable 5 Maintenance 35 Daily maintenance 21 Maintenance settings 28 Measuring spoon for ground coffee 4 Messages display 44 Milk Connecting milk 14 Milk foam 17 Milk system cleaning Cleaning the cappuccino frother 36 Milk system rinsing Rinsing the cappuccino frother 36 Milk warm 17 Permanently setting the water for the cup size 19 Permanent settings in programming mode 23 Power switch 5 Preparation 15 17 Cappuccino 1 Coffee 16 Espresso 16 Ground coffee 18 Hot water 20 Latte macchiato 17 Milk 17 Two speciality coffees 16 Problems Troubleshooting 45 Product settings 25 Programming mode 23 Automatic switch off 31 Background colour 33 Energy saving mode 30 Language 33 Maintenance settings 28 Product settings 25 Querying information 34 Restore factory settings 32 Setting the water hardness 29 Unit for amount of water 31 Proper use 6 Querying information 34 Rinsing Cappuccino frother 36 Machine 35 Rotary Switch 5 Safety 6 Safety information 6 Settings Maintenance settings 28 Permanent settings in programming mode 23 Setting up Setting up the machine 9 Switching off Machine 22 Switching on Machine 21 Switch off Automatic switch off 31 Symbol description 3 Technical data 48 Tel 52 Transport 47 Troubleshooting 45 Two products 16 Unit for amount of water 31 Us
16. 35 SUITE Wai Ware gare el g E E E econ enna er oneveret E eo nner err tent nmr en ere atre rr 35 RINSING the CAPPUCCINO rothen ccecsssssessssssecsessssesssssesorsesecsesesessesssessesescscsesesassusesessnsesesaesesesstasseeess 36 Cleaning te Cappuccino MONE sisien a n a aaa a E AA A ESNE 36 Dismantling and rinsing the cappuccino frother eeesesessesesessesesessesesessesesessssessecsestssssesesssssseeeeeseees 3 7 EI VS TN VC TIVE VS TUN ssnin oa a eree s Oa 3 7 REST AM NT TOS DN e N E E E AE A E E T 38 E E E A A E A 40 De cana TS RU Ve NIIP eaa E EEE E 4 Gleanna the Dean Contae escerai EE anaoa Ee RAEE OPEET 43 EEN e AT A e E E 43 6 Display messages 44 7 Troubleshooting 45 8 Transport and environmentally friendly disposal 47 Transporti Emptying the syste Tieeieee r raia E e A Ea EENE nee 47 Be A E PE E E A A EE A E T E E 47 9 Technical data 48 10 Index 49 11 JURA contact details Legal information 52 Symbol description Warnings ZA WARNING CAUTION CAUTION Symbols used gt 1 Espresso Always take note of any information marked with the words CAUTION or WARNING and a warning sign The signal word WARNING draws your attention to potential serious injury and the signal word CAUTION to potential minor injury CAUTION draws your attention to potential damage to the machine Prompt to take action This symbol means that you are being prompted to perform some action Information and tips to make it
17. MPRESSA is once more ready for use 1 If the descaling operation stops unexpectedly rinse the water tank thoroughly Cleaning the bean Coffee beans may be covered with a slight oil film which remains on container the walls of the bean container These traces may negatively affect the coffee result For this reason clean the bean container from time to time Precondition Fill bean container is displayed gt Switch the machine off with the On Off button gt Switch the machine off at the power switch gt Remove the aroma preservation cover gt Clean the bean container with a soft dry cloth gt Fill the bean container with coffee beans and close the aroma preservation cover Descaling the water tank Limescale deposits may form in the water tank To ensure correct function of the machine descale the water tank from time to time gt Remove the water tank gt If you use a CLARIS Pro Blue filter cartridge remove this gt Descale the tank with a mild conventional descaling agent in accordance with the manufacturer s instructions gt Rinse out the water tank thoroughly gt If you use a CLARIS Pro Blue filter cartridge insert this again gt Fill the water tank with fresh cold water and reinsert the tank 43 6 Display messages 6 Display messages Message Fill water tank Empty coffee grounds container Empty drip tray Drip tray not fitted Please press the Rota
18. PRESSA and on every aspect of coffee The following settings can only be made by the JURA service techni cian E Setting the filter capacity You can also obtain the following optional accessories for your IMPRESSA from your JURA service partner Coffee grounds disposal function set m Drip drain set m Permanent water connection kit m Payment system and other accessories If the machine is not lifted properly it may be damaged gt Do not lift the machine by the bean container gt Only lift the machine by gripping it underneath in the reces ses on the left and right sides of the machine When setting up your IMPRESSA please note the following m Place the IMPRESSA on a horizontal surface that is not sensi tive to water m Choose a spot for your IMPRESSA which protects the machine against overheating Ensure that the ventilation slots are not covered 1 Preparing and using for the first time Filling the water tank Daily maintenance of the machine and hygiene when handling milk coffee and water are key to a perfect coffee result in the cup every time You should therefore change the water daily CAUTION Milk sparkling mineral water or other liquids can damage the water tank or the machine gt Only fill the water tank with fresh cold water gt Open the water tank cover gt Remove the water tank and rinse it with cold water gt Fill the water tank with fresh cold water and reinsert the tank gt Close t
19. ayed 46 Cause Result The connector of the cappuccino frother may be blocked by milk residues or limescale fragments loosened during descaling There are foreign objects in the grinder If the machine was exposed to the cold for a long period of time heating is disabled for safety reasons Action gt Remove the cappuccino frother gt Unscrew the black connector with the aid of the hexagonal hole on the measuring spoon for ground coffee gt Clean the connector thoroughly gt Screw the connector back on by hand gt Carefully tighten it using the hexagonal hole on the measuring spoon turning by no more than a quarter of a rotation gt Contact customer support in your country see Chapter 11 JURA contact details Legal information gt Warm the machine at room tempera ture gt Switch the IMPRESSA off at the power switch Contact customer support in your country see Chapter 11 JURA contact details Legal information i f you were unable to solve the problem contact customer support in your country see Chapter 11 JURA contact details Legal information 8 Transport and environmentally friendly disposal 8 Transport and environmentally friendly disposal Transport Emptying the system Disposal In order to protect the IMPRESSA from frost during transport the system must be emptied Precondition Please select product is displayed gt Caref
20. ble The lock symbol indicates whether the product is enabled or disabled If the lock is closed the product is disabled gt Press the Next button until the product Hot water is dis played gt Press the Hot water button The lock is closed Hot water preparation is now disabled P gt Press the P button to exit programming mode Please select product On the start screen Hot water is greyed out Maintenance settings In the programme item Maintenance settings 3 6 you can make the following settings m Filter Activate the CLARIS Pro Blue filter cartridge see Chapter 5 Maintenance Inserting and activating the filter m Water hardness f you do not have a filter cartridge you will need to set the water hardness see Chapter 4 Permanent settings in pro gramming mode Setting the water hardness m Switch on rinse Manual The switch on rinse must be started manually m Switch on rinse Automatic The switch on rinse is started automatically m Rinse the milk system After 10 min You are prompted to rinse the milk system 10 minutes after preparation of a speciality coffee with milk 28 4 Permanent settings in programming mode m Rinse the milk system immediate You are prompted to rinse the milk system immediately after preparation of a speciality coffee with milk Example Proceed as follows t
21. button Preparation starts and the coffee flows into the cup gt Press any button as soon as there is sufficient coffee in the cup Preparation stops Saved appears briefly on the display The set amount of water for one coffee is permanently stored Please select product appears on the display You can alter this setting at any time by repeating the above procedure You can also permanently set the amount for all speciality cof fees hot water and milk in programming mode see Chapter 4 Permanent settings in programming mode Product set tings 2 Preparation Hot water The following temperatures can be selected for preparing hot water Low Normal X high A CAUTION There is a danger of scalding from hot water splashes gt Avoid direct contact with the skin gt Place a cup under the hot water nozzle gt Press the Hot water button Hot water and the temperature are displayed By pressing the lt or gt button several times within approx imately 2 seconds you can set the temperature to your indi vidual preference This setting is not saved p e Hot water hot water flows into the cup Preparation stops automatically Please select product appears on the display 20 3 Daily operation Switching on 3 Daily operation When the IMPRESSA is switched on it automatically prompts you to perform the rinse operation Star
22. ceptacle holding 600 ml of water This may take several minutes gt Pour the solution into the empty water tank and insert it into the machine Please press the Rotary Switch gt Remove the cappuccino frother gt Place a receptacle under the connector of the cappuccino frother and another under the hot water nozzle gt Press the Rotary Switch Machine is being descaled water flows repeatedly out of the connector of the cappuccino frother and the hot water nozzle The operation is interrupted Empty drip tray gt Empty both receptacles gt Empty the drip tray and coffee grounds container and put them back into the machine Fill water tank gt Remove the water tank and rinse it thoroughly gt Fill the water tank with fresh cold water and reinsert the tank Please press the Rotary Switch gt Refit the cappuccino frother 42 5 Maintenance gt Place a receptacle under the cappuccino frother the coffee spout and the hot water nozzle gt Press the Rotary Switch Machine is being descaled water flows out of the hot water nozzle and the cappuccino frother Machine is heating Machine is rinsing water flows out of the coffee spout The operation stops automatically Empty drip tray gt Empty the drip tray and coffee grounds container and put them back into the machine Descaling is now complete Your I
23. dditional speciality coffees in the product selector m Ristretto m 2 espressi m 2 coffees m 2 ristretti 15 2 Preparation Espresso and coffee Espresso and Coffee are prepared following this model Example Proceed as follows to prepare one coffee gt Place a cup under the coffee spout gt Press the Coffee button Preparation starts The preset amount of water for coffee flows into the cup Preparation stops automatically Please select product appears on the display Preparing two speciality To prepare two speciality coffees either use the product selector or coffees press the appropriate preparation button twice within approximately 2 seconds Example Proceed as follows to prepare two coffees using product selector gt Place two cups under the coffee spout Turn the Rotary Switch to view the product selector gt Turn the Rotary Switch until 2 coffees is displayed gt Press the Rotary Switch Coffee preparation starts The preset amount of water for coffee flows into the cups Preparation stops automatically Please select product appears on the display Proceed as follows to prepare two cups of coffee at the touch pi e of a button Place two cups under the coffee spout Press the Coffee button twice within approximately 2 seconds to start coffee preparation 16 Latte macchiato Cappuccino
24. e First time 11 10 Index W Warm milk 17 Water hardness Determining the water hardness 13 Setting the water hardness 29 Water tank 4 Descaling 43 Filling 10 Website 9 51 Art 70542 X 9 en 201202 11 JURA contact details Legal information 11 JURA contact details Legal information Your JURA service partner JURA Elektroapparate AG Kaffeeweltstrasse 10 CH 4626 Niederbuchsiten Tel 41 0 62 38 98 233 www jura com Directives The machine complies with the following directives m 2006 42 EC Machinery Directive m 2004 108 EC Electromagnetic Compatibility m 2009 125 EC Ecodesign Directive Technical changes We reserve the right to make technical changes The diagrams used in these instructions for use are for illustration purposes only and do not represent the original colours of the machine Some details of your IMPRESSA may vary Feedback Your opinion is important to us Use the contact link at www jura com Copyright The instructions for use contain information which is protected by copyright It is not permitted to photocopy these instructions for use or translate them into another language without the prior written consent of JURA Elektroapparate AG 52
25. ed as follows to prepare one espresso using ground coffee gt Place an espresso cup under the coffee spout gt Open the cover of the filler funnel for ground coffee Please add ground coffee gt Place one level measuring spoon of ground coffee into the filler funnel gt Close the cover of the filler funnel Please select product Permanently setting the amount of water for the cup size 2 Preparation gt Press the Espresso button Preparation starts The preset amount of water for espresso flows into the cup Preparation stops automatically Please select product appears on the display It is easy to make permanent settings for the amount of water for all speciality coffees and hot water according to the cup size Adjust the amount once as shown in the following example Every time you prepare a drink in the future this amount of water will be dispensed The permanent settings for adapting the amount of water to the cup size for all speciality coffees and hot water follow this model Example Proceed as follows to permanently set the amount of water for one coffee Precondition Please select product is displayed mo p e gt Place a cup under the coffee spout gt Press and hold the Coffee button Coffee and the fill volume are displayed gt Hold the Coffee button down until Enough water Press button appears gt Release the Coffee
26. er 4 Permanent settings in programming mode By instructing your IMPRESSA to automatically switch itself off you can cut down your energy consumption If this function is activated your IMPRESSA switches off automatically after the preset time fol lowing the last action on the machine You can set the automatic switch off to 15 minutes 30 minutes or 1 15 hours Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 4 6 is displayed gt Press the Switch off after button Switch off after gt Press the lt or gt button to change the setting gt Press the Save button Saved appears briefly on the display Machine settings 4 6 P gt Press the P button to exit programming mode Please select product You can change the unit for the amount of water from ml to oz Example Proceed as follows to change the unit for the amount of water from ml to oz Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Machine settings 4 6 is displayed gt Press the Units button Units gt Press the oz button gt Press the Save button Saved appears briefly on the display
27. er cartridge If the water hardness is 10 dH or more we recommend using the filter cartridge If you do not know the hardness of your water you can find this out first see Chapter 1 Pre paring and using for the first time Determining the water hard ness If you did not activate the filter cartridge the first time you used the machine you can do this now as follows i Perform the inserting the filter operation without any inter ruptions This will ensure that your IMPRESSA always produces its best Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Mainte nance settings 3 6 is displayed 37 5 Maintenance Changing the filter 38 me mm e mio gt Press the Filter button Filter gt Press the Active button gt Press the Save button Saved appears briefly on the display Insert filter gt Remove and empty the water tank gt Open the filter holder and insert the filter cartridge into the water tank exerting slight pressure gt Close the filter holder It will click into place audibly After two months the filter will cease to work Set the date on the date plate on the filter holder in the water tank gt Fill the water tank with fresh cold water and reinsert the tank gt Place a receptacle under the hot water n
28. h aroma preservation cover 4 Automatic switch off 31 B Background colour 33 Bean container Bean container with aroma preservation cover 4 Cleaning 43 Filling 10 Bus bar Technical data 48 Button On Off button 5 P button programming 5 C Cappuccino 1 Cappuccino frother Cleaning 36 Rinsing 36 CLARIS Pro Blue filter cartridge Changing 38 Inserting and activating the filter 37 Cleaning Bean container 43 Cappuccino frother 36 Machine 40 Coffee 16 Coffee grounds container 4 Coffee spout Height and width adjustable coffee spout 4 Consistency of grind Adjusting the grinder 14 Grinder adjustment switch 4 Contact details 52 Cover Storage compartment 4 Water tank 4 Cup grille 4 Customer support 52 10 Index Descaling Machine 41 Water tank 43 Display 5 Display messages 44 Display settings 33 Disposal 47 Double product 16 Drip tray 4 Emptying the system 47 Energy saving mode 30 Errors Troubleshooting 45 Espresso 16 Factory settings Restore factory settings 32 Filler funnel Filler funnel for ground coffee 4 Filling Bean container 10 Water tank 10 Filter Changing 38 Inserting and activating the filter 37 First time use 11 Frother Cappuccino frother 4 Grinder adjustment switch 4 Ground coffee 18 Measuring spoon for ground coffee 4 Hotline 52 Hot water 20 Hot water nozzle 4 Instant coffee Ground coffee 18 Internet 9 49 10 Index JURA Contact details 52 Internet 9 Language 3
29. he water tank cover Filling the bean container The bean container has an aroma preservation cover This will ensure that your coffee beans retain their aroma for longer CAUTION Coffee beans which have been treated with additives e g sugar ground coffee or freeze dried coffee will damage the grinder gt Only use untreated coffee beans to fill the bean container gt Open the bean container cover and remove the aroma pre servation cover gt Remove any dirt or foreign objects from inside the bean container gt Fill the bean container with coffee beans then close the aroma preservation cover and the bean container cover 10 1 Preparing and using for the first time First time use When using the machine for the first time you can choose whether you want to operate IMPRESSA with or without the CLARIS Pro Blue filter cartridge If the water hardness is 10 dH or more we recom mend using the filter cartridge If you do not know the hardness of your water you can find this out first see Chapter 1 Preparing and using for the first time Determining the water hardness A WARNING If the machine is operated with a defective mains cable there is a danger of potentially fatal electric shock gt Never use a machine which is damaged or has a defective mains cable Precondition The water tank and bean container have been filled gt Insert the mains plug into a power socket gt Switch on the IMPRESSA using the
30. ilk are rinsed gt Place one receptacle under the coffee spout and another under the cappuccino frother gt Press the On Off button Machine is rinsing Milk system is being rinsed The spouts used to prepare a speciality coffee or milk are rinsed The operation stops automatically Your IMPRESSA is switched off i When the IMPRESSA is switched off with the On Off button the machine consumes less than 0 1 W of standby energy The machine can be completely disconnected from the power supply using the power switch 22 4 Permanent settings in programming mode 4 Permanent settings in programming mode Programme item Maintenance status 1 6 Product settings 2 6 Maintenance settings 3 6 Machine settings 416 Machine settings 5 67 Press the P button to enter programming mode You can navigate through the programme items and permanently save the required settings simply by turning the Rotary Switch and using the multi function buttons The following settings can be made Sub item Clean Descale only if filter is not activated Change the filter only if filter is activated Rinse the coffee system Clean the milk system Expert mode product selector One off settings Lock enable Filter Water hardness only if filter is not activated Switch on rinse Rinse the milk system Sa
31. ilk pipe to a milk cooler 14 2 Preparation Ways of preparing a beverage 2 Preparation You can stop preparation of a speciality coffee speciality cof fee with milk or hot water at any time Just press any button During the grinding operation you can select the coffee strength of individual products by turning the Rotary Switch extra mild 22 mild 222 normal 2222 strong or 9222 extra strong fale mo During preparation you can change the preset amount of water by turning the Rotary Switch or pressing the lt and gt buttons i You can follow the current status of preparation on the display mo In programming mode you can enable or disable one off settings during preparation see Chapter 4 Permanent settings in program ming mode Enable or disable one off settings You can make permanent settings for all products in programming mode see Chapter 4 Permanent settings in programming mode Product settings Only some of the speciality coffees you can prepare are shown on the display at any one time As soon as you turn the Rotary Switch more speciality coffees are displayed in the product selector The product selector disappears automatically after 5 seconds if no pre paration is started The following speciality coffees are displayed as standard m Espresso Coffee Cappuccino Latte macchiato Hot water portion milk A
32. is can cause irritation gt Avoid contact with the skin or eyes gt Rinse off the descaling agent with clean water Should you get any descaling agent in your eye see a doctor If the wrong descaling agent is used the machine could be dama ged and or traces could be left behind in the water gt Use only original JURA maintenance products If the descaling operation is interrupted there may be damage to the machine gt Allow the descaling programme to run to the end If the descaling agent comes into contact with sensitive surfaces e g marble damage cannot be ruled out gt Clean up any splashes immediately The descaling programme lasts approximately 50 minutes JURA descaling tablets are available from specialised dealers If you use a CLARIS Pro Blue filter cartridge and this is activated you will not be prompted to descale me pmo mio 41 5 Maintenance Precondition Please select product is displayed The symbol is also displayed P gt Press the P button Maintenance status 1 6 gt Press the Descale button Descale 1 fyou do not want to start descaling just yet press the L but ton gt Press the Next button Empty drip tray gt Empty the drip tray and coffee grounds container and put them back into the machine Pour descaling agent into water tank gt Remove and empty the water tank gt Completely dissolve 3 JURA descaling tablets in a re
33. me to JURA Please press the Rotary Switch vy Place a receptacle under the cappuccino frother and another under the hot water nozzle Press the Rotary Switch System is filling the system fills up with water Water flows out of the cappuccino frother and the hot water nozzle The operation stops automatically Welcome to JURA appears on the display Machine is heating Please press the Rotary Switch the Rotary Switch lights up A Place a receptacle under the coffee spout Press the Rotary Switch Machine is rinsing the machine rinses The operation stops automatically Please select product appears on the display Your IMPRESSA is ready for use The display shows the products you can prepare mio Determining the water You can find out what the water hardness is by using the Aquadur hardness test strip supplied as standard gt Hold the test strip briefly for 1 second under flowing water Shake off the water gt Wait for about one minute gt You will then be able to read the degree of water hardness from the discolouration of the Aquadur test strip and the p description on the packaging HEHH You can now adjust the water hardness AN tauchen Dip briefly 1 sec Plongez bri vement leicht ab shake off excess 1 sec gouttez y inund nach water and compare l exc s d eau et com i parez apr s 1 mi i
34. metal contacts of the drip tray are dirty or wet The water tank float is trapped 7 Troubleshooting Action gt Turn the setting wheel of the cappuc cino frother to the far right and the Milk Foam position gt Change the length of the interval to at least 30 seconds in programming mode see Chapter 4 Permanent settings in programming mode Product settings gt Rinse and clean the cappuccino frother see Chapter 5 Maintenance Rinsing the cappuccino frother gt Check that the air intake pipe is fitted on the cappuccino frother gt Rinse or replace the air intake pipe You will find a replacement in the Welcome Pack gt Put the grinder on a coarser setting or use coarser ground coffee see Chapter 1 Preparing and using for the first time Adjusting the grinder gt Perform descaling see Chapter 5 Maintenance Descaling the machine gt Deactivate the filter cartridge in programming mode gt Pull the sliding catch on the right hand side of the bean container fully out gt Clean and dry the metal contacts on the back of the drip tray gt Descale the water tank see Chapter 5 Maintenance Descaling the water tank 45 7 Troubleshooting Problem Little or no water or steam comes out of the cappuccino frother The pump is very quiet Grinder is making a very loud noise ERROR 2 is displayed Other ERROR messages are dis pl
35. nge setting for the interval to 40 sec Press the Save button Saved appears briefly on the display Latte macchiato y D v Press the P button to exit programming mode Please select product Enable or disable one off In the programme item Product settings 2 6 One off settings settings you can make the following setting m Active One off settings can be made during preparation e g coffee strength or amount of water m Inactive One off settings cannot be made during preparation The product is prepared according to the settings in program ming mode Product settings 2 6 Expert mode Example Proceed as follows to disable one off settings during pre paration Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Product settings 2 6 is displayed gt Press the One off settings button One off settings gt Press the Inactive button 26 4 Permanent settings in programming mode gt Press the Save button Saved appears briefly on the display Product settings 2 6 P gt Press the P button to exit programming mode Please select product One off settings cannot now be made during preparation Enabling and disabling In the programme item Product settings 2 6 product
36. o frother gt Turn the setting wheel of the cappuccino frother to the Milk Foam position i Ifyou want to heat the milk turn the setting wheel of the cap puccino frother to the Milk position U 17 2 Preparation Ground coffee 18 gt Press the 1 portion milk button The machine heats up portion milk the milk foam is prepared Preparation stops automatically when the preset amount of milk foam is reached Please select product appears on the display To make sure the cappuccino frother always works properly rinse and clean it regularly see Chapter 5 Maintenance Rinsing the cap puccino frother You can choose to use a second coffee variety for example decaffe inated coffee with the filter funnel for ground coffee i i mie m o Never add more than two level measuring spoons of ground coffee Use ground coffee which is not ground too finely Very fine coffee can block up the system so that the coffee only comes out in drips If you did not fill the machine with a sufficient amount of ground coffee Not enough ground coffee is displayed and the IMPRESSA stops the operation The desired speciality coffee must be prepared within appro ximately one minute after filling with the ground coffee Otherwise the IMPRESSA stops the operation and is once more ready for use All speciality coffees with ground coffee are prepared following this model Example Proce
37. o make the machine prompt you to rinse the milk system immediately after preparing a speciality cof fee with milk Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Mainte nance settings 3 6 is displayed gt Press the Rinse the milk system button Rinse the milk system gt Press the Immediate button gt Press the Save button Saved appears briefly on the display Maintenance settings 3 6 P gt Press the P button to exit programming mode Please select product m e Setting the water If you are using the CLARIS Pro Blue filter cartridge and have hardness activated it it is not possible to set the water hardness The harder the water is the more frequently the IMPRESSA needs to be descaled It is therefore important to set the water hardness accu rately The water hardness can be adjusted on a continuous scale between 1 dH and 30 dH Example Proceed as follows to change the water hardness from NGG to 23a Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Mainte nance settings 3 6 is displayed gt Press the Water hardness button Water hardness 29 4 Permanent settings in programming mode gt Press the
38. on the underside of your IMPRESSA Further technical data is provided in these instructions for use see Chapter 9 Technical data Please only use original JURA maintenance products Use of products that are not explicitly recommended by JURA could damage the IMPRESSA Important information Do not use any coffee beans treated with additives or carame lised coffee beans Only fill the water tank with fresh cold water Switch the machine off at the power switch if you are going to be absent for a longer period of time People including children who do not have the physical sensory or mental capabilities to use the machine safely or are inexperienced or lack knowledge in how to use the machine safely must be supervised by a responsible person when using it or must be instructed in how to use it correctly Safety when handling the CLARIS Pro Blue filter cartridge Filter cartridges should be kept out of the reach of children Store filter cartridges in a dry place in the sealed packaging Protect cartridges from heat and direct sunlight Do not use damaged filter cartridges Do not open filter cartridges 1 Preparing and using for the first time 1 Preparing and using for the first time JURA on the Internet Settings by the JURA service technician Setting up the machine CAUTION Visit us on the Internet On the JURA website www jura com you will find interesting and up to date information on your IM
39. ozzle gt Press the Next button Filter is being rinsed water flows out of the hot water nozzle You can interrupt rinsing of the filter at any time by pressing any button Press the Rotary Switch to continue rinsing of the filter The water may be slightly discoloured This is not harmful to health and does not affect the taste Rinsing of the filter stops automatically The machine heats up Please select product Your IMPRESSA is once more ready for use After 120 litres of water have flowed through the filter will cease to work Your IMPRESSA will automatically prompt you to change the filter After two months the filter will cease to work Set the date on the date plate on the filter holder in the water tank If the CLARIS Pro Blue filter cartridge is not activated in pro gramming mode you will not be prompted to change the fil ter 5 Maintenance Precondition Please select product is displayed The symbol is also displayed P mme mo m e gt Press the P button Maintenance status 1 6 gt Press the Change the filter button Change the filter If you do not want to start changing the filter just yet press the t button gt Press the Next button Change filter gt Remove and empty the water tank gt Open the filter holder and remove the old CLARIS filter cart ridge gt Insert the New filter cartridge into the
40. r the first time Filling the bean container gt Press the Rotary Switch to start rinsing the milk system gt Press the P button to view the list of maintenance programmes Maintenance status 1 6 By referring to the bar you can see which maintenance programme is due When the bar is completely filled with red your IMPRESSA will prompt you to perform the appropriate maintenance programme gt The next time you prepare a beverage add more ground coffee see Chapter 2 Preparation Ground coffee 7 Troubleshooting Problem When preparing a latte macchiato the typical three layers do not form Insufficient foam is produced when the milk is frothed or milk sprays from the cappuccino frother Coffee only comes out in drips when it is being prepared Water hardness cannot be adjusted Fill bean container is displayed although the bean container is full Empty drip tray is always displayed Fill water tank is displayed although the water tank is full Cause Result The cappuccino frother is dirty Coffee or ground coffee has been ground too finely and is blocking the system The same filter cartridge may have been used several times or the water hardness set incorrectly in the programming mode The CLARIS Pro Blue filter cartridge is activated The sliding catch for the bean container has not been pulled out or has not been pulled out completely The
41. ress the Clean button Clean If you do not want to start cleaning just yet press the t but ton gt Press the Next button Empty drip tray gt Empty the drip tray and coffee grounds container and put them back into the machine Please press the Rotary Switch gt Place one receptacle under the coffee spout and another under the cappuccino frother gt Press the Rotary Switch Machine is being cleaned water flows out of the coffee spout The operation is interrupted Add cleaning tablet gt Open the cover of the filler funnel for ground coffee Descaling the machine A CAUTION CAUTION CAUTION CAUTION 5 Maintenance gt Insert a JURA cleaning tablet into the filler funnel gt Close the cover of the filler funnel Please press the Rotary Switch gt Press the Rotary Switch Machine is being cleaned water flows repeatedly out of the coffee spout and the cappuccino frother The operation is interrupted Empty drip tray gt Empty the drip tray and coffee grounds container and put them back into the machine Cleaning is now complete Your IMPRESSA is once more ready for use The IMPRESSA builds up deposits of limescale over time and auto matically prompts you to descale it when necessary The degree of calcification depends on the hardness of your water If the descaling agent comes into contact with the skin or eyes th
42. ry Switch Fill bean container Rinse the milk system Please select product is displayed The symbol is also displayed Not enough ground coffee 44 Cause Result The water tank is empty You cannot prepare any products The coffee grounds container is full You cannot prepare any products The drip tray is full You cannot prepare any products The drip tray is not inserted correctly or is not inserted at all You cannot prepare any products The IMPRESSA is prompting you to perform a rinse or continue a maintenance programme that was already started The bean container is empty You cannot prepare any products The IMPRESSA is prompting you to rinse the milk system The IMPRESSA is prompting you to perform a maintenance programme There is insufficient ground coffee in the machine the IMPRESSA stops the operation Action gt Fill the water tank see Chapter 1 Preparing and using for the first time Filling the water tank gt Empty the coffee grounds container and the drip tray see Chapter 3 Daily operation Daily maintenance gt Empty the drip tray and the coffee grounds container gt Clean and dry the metal contacts on the back of the drip tray gt Fit the drip tray gt Press the Rotary Switch to start the rinse or to continue the maintenance programme gt Fill the bean container see Chapter 1 Preparing and using fo
43. selector product selector view you can make the following setting m Active Product selector view is active and can be started by turning the Rotary Switch when the IMPRESSA is ready for use m Inactive Product selector view is inactive Example Proceed as follows to disable product selector view Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Product settings 2 6 is displayed gt Press the product selector button product selector Press the Inactive button vy v Press the Save button Saved appears briefly on the display Product settings 2 6 Press the P button to exit programming mode Please select product Product selector view can now no longer by started by tur U A ning the Rotary Switch 27 4 Permanent settings in programming mode Enabling and disabling In the programme item Product settings 2 67 Lock enable you products can enable or disable each individual product Example For example you can disable the preparation of hot water Precondition Please select product is displayed P gt Press the P button Maintenance status 1 6 Turn the Rotary Switch until the programme item Product settings 2 6 is displayed gt Press the Lock enable button Lock ena
44. ss the Next button Filter is being rinsed water flows out of the hot water nozzle You can interrupt rinsing of the filter at any time by pressing any button Press the Rotary Switch to continue rinsing of the filter The water may be slightly discoloured This is not harmful to health and does not affect the taste Rinsing of the filter stops automatically System is filling the system fills up with water Water flows out of the cappuccino frother and the hot water nozzle The operation stops automatically Welcome to JURA Machine is rinsing the machine rinses The operation stops automatically Please select product appears on the display Your IMPRESSA is ready for use The display shows the products you can prepare CAUTION Milk sparkling mineral water or other liquids can damage the water tank or the machine gt 12 Only fill the water tank with fresh cold water gt Press the Inactive button gt Press the Save button Saved appears briefly on the display Water hardness 1 Preparing and using for the first time i Ifyou do not know the hardness of your water you must find this out first see Chapter 1 Preparing and using for the first time Determining the water hardness gt Press the lt or gt button to set the water hardness gt Press the Save button Saved appears briefly on the display Welco
45. t the rinse operation by pressing the Rotary Switch In programming mode you can change this setting so that the machine starts the switch on rinse automatically see Chapter 4 Permanent settings in programming mode Main tenance settings Precondition Your IMPRESSA is switched on at the power switch gt Place a receptacle under the coffee spout gt Press the On Off button to switch the IMPRESSA on Welcome to JURA appears on the display The machine heats up Please press the Rotary Switch gt Press the Rotary Switch The machine rinses The operation stops automatically Please select product appears on the display To ensure that you get many years of reliable service out of your IMPRESSA and to guarantee the optimum coffee quality the machine requires daily maintenance gt Pull out the drip tray gt Empty the coffee grounds container and the drip tray Rinse them both with warm water gt Dry the metal contacts on the back of the drip tray gt Refit the coffee grounds container and the drip tray gt Rinse the water tank with clean water gt Dismantle and rinse the cappuccino frother see Chapter 5 Maintenance Dismantling and rinsing the cappuccino fro ther gt Wipe the surface of the machine with a clean soft damp cloth e g microfibre cloth 21 3 Daily operation Switching off When you switch your IMPRESSA off the spouts used to prepare a speciality coffee or m
46. the P button Example Proceed as follows to disable programming mode Precondition Please select product is displayed gt Remove the water tank Fill water tank gt Press the Rotary Switch the P button and the bottom right hand button simultaneously for about 2 seconds The machine is locked is briefly displayed Fill water tank Programming mode is disabled To enable programming mode again remove the water tank Then press the Rotary Switch the P button and the bottom right hand button simultaneously for about 2 seconds The machine is enab led is briefly displayed Programming mode is enabled again 4 Permanent settings in programming mode Product settings In the programme item Product settings 2 6 Expert mode you can make individual settings for all speciality coffees milk and hot water The following settings can be made Product Temperature Coffee strength Amount Ristretto Normal High extra mild 2 mild 2 Volume espresso normal 224 strong eee 25 ml 240 ml coffee extra strong 2222 Two ristretti Normal High Volume two espressi 25 ml 240 ml two coffees per cup Latte macchiato Normal High extra mild 2 mild 24 Amount of milk cappuccino normal 22 strong 222 3 sec 120 sec extra strong 2222 Interval 0 sec 60 sec Volume
47. ully pull the cappuccino frother down and off gt Place a receptacle under the connector of the cappuccino frother gt Press the 1 portion milk button portion milk hot steam is discharged from the connector gt Remove and empty the water tank Turn the Rotary Switch until 60 sec is displayed Steam will continue to be discharged from the connector until the system is empty Fill water tank gt Press the On Off button The IMPRESSA is switched off Please dispose of old machines in an environmentally neutral way B Old machines contain valuable recyclable materials which should be recycled Please therefore dispose of old machines via suitable collection systems 47 9 Technical data 9 Technical data 48 Voltage Power Airborne noise emitted Ambient conditions Conformity mark Energy consumption Save energy Active Energy consumption Save energy Inactive Pump pressure Holding capacity of water tank Holding capacity of bean container Holding capacity of coffee grounds container Cable length Weight Dimensions W x H x D 220 240 V 50 Hz 1450 W Le lt 70 dB A Humidity max 80 Ambient temperature 10 35 C CEO approx 4 1 Wh approx 10 6 Wh Static max 15 bar 4 500 g max 40 portions approx 1 1 m approx 12 8 kg 33 8 x 49 7 x 43 2 cm 10 Index A Addresses 52 Aroma preservation cover Bean container wit
48. ur 250 ml of fresh water into a receptacle and add one capful of Cappuccino Cleaner Immerse the milk pipe in the receptacle Turn the setting wheel of the cappuccino frother to the Milk Foam or Milk 0 position A v A Place another receptacle under the cappuccino frother Press the Next button Milk system is being cleaned water flows out of the cap A puccino frother Water for cleaning milk system gt Rinse the receptacle thoroughly fill it with 250 ml of fresh water and immerse the milk pipe in the water Dismantling and rinsing the cappuccino frother Inserting and activating the filter 5 Maintenance gt Empty the other receptacle and place it under the cappuc cino frother again gt Press the Next button Milk system is being cleaned the cappuccino frother and the pipe are rinsed with fresh water Please select product appears on the display gt Carefully pull the cappuccino frother down and off gt Dismantle the cappuccino frother into its individual parts gt Rinse all parts of the cappuccino frother thoroughly under running water gt Reassemble the cappuccino frother Ensure that all individual parts are correctly and firmly con nected to ensure correct operation of the cappuccino frother gt Firmly attach it to the connector Your IMPRESSA no longer has to be descaled if you are using the CLARIS Pro Blue filt
49. ve energy Switch off after Units Factory setting Choose language Display Colour scheme Explanation gt Start the required maintenance pro gramme here gt Select your settings for speciality coffees and hot water gt Deactivate the product selector view gt Specify whether or not to allow one off settings during preparation gt Enable or disable individual products gt Indicate whether you are operating your IMPRESSA with or without a CLARIS Pro Blue filter cartridge gt Adjust the water hardness gt Change the settings for the switch on rinse and milk system rinse gt Select an energy saving mode gt Set the time after which the IMPRESSA should switch off automatically gt Select the unit for the amount of water gt Reset the permanently set values of all products to the factory settings gt Select your language and the background colour for the display 23 4 Permanent settings in programming mode Programme item Information 6 6 Enabling and disabling programming mode 24 Sub item Explanation Product counter gt Keep track of all speciality coffees prepared and view the number of maintenance programmes performed Maintenance counter Day counter Version You can set your IMPRESSA such that programming mode is disab led When programming mode is disabled it cannot be accessed by pressing
50. water tank exerting slight pressure gt Close the filter holder It will click into place audibly gt Fill the water tank with fresh cold water and reinsert the tank gt Place a receptacle at least 500 ml under the hot water nozzle gt Press the Next button Filter is being rinsed water flows out of the hot water nozzle You can interrupt rinsing of the filter at any time by pressing any button Press the Rotary Switch to continue rinsing of the filter The water may be slightly discoloured This is not harmful to health and does not affect the taste Rinsing of the filter stops automatically after approximately 500 ml The machine heats up Please select product appears on the display 39 5 Maintenance Cleaning the machine CAUTION 40 After 200 preparations or 80 switch on rinses the IMPRESSA will prompt you to clean it If the wrong cleaning agent is used the machine could be damaged and or traces could be left behind in the water gt mmo mule i Use only original JURA maintenance products The cleaning programme lasts approximately 20 minutes Do not interrupt the cleaning programme The quality of cleaning will be impaired if you do so JURA cleaning tablets are available from specialised dealers Precondition Please select product is displayed The symbol is also displayed P mo gt Press the P button Maintenance status 1 6 gt P
51. with the instructions they contain A warranty service is not applicable for damage or defects caused by non compliance with the instructions for use Keep these instructions for use close to the machine and pass them on to the next user The IMPRESSA may only be operated by instructed persons Non professionals must be supervised during use Please carefully read and observe the important safety information set out below To avoid danger of potentially fatal electric shock m Never use a machine which is damaged or has a defective mains cable m Inthe event of signs of damage for example if there is a smell of burning unplug the machine immediately from the mains supply and contact JURA service m lf the mains cable of this machine is damaged it must be repaired either directly by JURA or by an authorised JURA service centre m Make sure that the IMPRESSA and the mains cable are not located close to hot surfaces m Be careful to ensure that the mains cable is not trapped and does not rub against sharp edges m Never open and repair the machine yourself Do not modify the machine in any way that is not described in these instruc tions for use The machine contains live parts If opened there is a danger of potentially fatal injury Repairs may only be car ried out by authorised JURA service centres using original Spare parts and accessories Important information m To completely and safely disconnect the machine from the
Download Pdf Manuals
Related Search