Home

Powerplus POW30543 power drill

1. Disconnect the plug from the power source before making adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store power tools when not in use out of the reach of children and do not allow people who are not familiar with the power tool or these instructions to operate it Power tools are potentially dangerous in the hands of untrained users Maintain power tools Check for misalignment or jammed moving parts breakages or any other feature that might affect the operation of the power tool If it is damaged the power tool must be repaired Many accidents are caused by using poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control Use the power tool accessories and cutting tools etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work which needs to be done Using a power tool in ways for which it was not intended can lead to potentially hazardous situations 5 5 Service Your power tool should be serviced by a qualified specialist using only standard spare parts This will ensure that it meets the required safety standards 6 SAFETY REGULATIONS Important To protect yourself from the risk of electric shock in
2. SYMBOLS The following symbols are used in this manual and or on the machine Denotes risk of personal injury or damage to the tool Read manual before use safety standards of applicable insulated Earthing wire is C 3 In accordance with essential Class II The machine is double em European directives therefore not necessary Copyright 2014 VARO NV Page 2 www varo com POWE R E L U S POW30543 EN DESIGNED AND MARKETED BY VARO 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions Failure to heed warnings and follow instructions may result in electric shock fire and or serious injury Keep safety warnings and instructions for future reference The term power tool in the safety warnings refers to your mains operated corded power tool or battery operated cordless power tool 5 1 Working area Keep working area clean and well lit Untidy and dark areas can lead to accidents Do not operate power tools in potentially explosive surroundings for example in the presence of inflammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders at a distance when operating a power tool Distractions can cause you to lose control of it 5 2 Electrical safety Always check that the power supply corresponds to the voltage on the rating plate Power tool plugs must match the outlet Never modify the plug in any way Do not use ad
3. tool holder as far as it will go The tool will lock automatically Check that it has locked by pulling the tool 7 2 Removing SDS plus tool Fig 3 Pull back fastening sleeve hold and remove tool 8 STARTING WORK 8 1 Switching ON OFF Switching on Press the operating switch Switching off Press the operating switch briefly and let go 8 2 Handle attachment Fig 4 For reasons of safety only use the hammer drill with handle attachment You will be able to obtain a safe body position when working by rotating the handle attachment Loosen and turn the handle attachment in an anti clockwise direction Then tighten the handle attachment 8 3 Depth stop Fig 5 Loosen the handle attachment and place the straight part of the depth stop in the hole Adjust the depth stop and retighten the handle attachment Copyright 2014 VARO NV Page 5 www varo com POWERPLUS Lous EN 8 4 Dust collection device Fig 6 Before carrying out hammer drilling work vertically overhead pull dust collecting device over the drill bit 8 5 Hammer stop Your hammer drill is equipped with a hammer stop facility for smooth drilling To deactivate the hammer action turn the lever switch clockwise to position To reactivate the hammer action the lever switch has to be reset to position 8 6 Drill Stop Fig 7 You can deactivate the drilling action of the hammer drill when using it for chiselling work Todo so turn the lever selector so
4. DECLARATION OF CONFORMITY VARO N V Joseph Van Instraat 9 BE2500 Lier BELGIUM declares that Product hammer drill 900W Trade mark POWERplus Model POW30543 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives based on the application of European harmonized standards Any unauthorized modification of the apparatus voids this declaration European Directives including if applicable their amendments up to the date of signature 2011 65 EU 2004 108 EC 2006 42 EC 2000 14 EC Annex V LwA 100dB A 103dB A European harmonized standards including if applicable their amendments up to the date of signature EN60745 1 2009 EN60745 2 6 2010 EN55014 1 2006 EN55014 2 1997 EN61000 3 2 2006 EN61000 3 3 2008 Keeper of the Technical Documentation Philippe Vankerkhove VARO Vic Van Rompuy N V The undersigned acts on behalf of the company CEO Hugo Cuypers Regulatory Affairs Compliance Manager 06 09 13 Copyright 2014 VARO NV Page 8 www varo com
5. POWE R L U S POW30543 EN DESIGNED AND MARKETED BY VARO 1 APPLICA TON corian eaiectsce can cece ceeece neue eeeeansunadectmeeeeccuetancuane 2 2 DESCRIPTION FIG 1 sisiisnccccssiscisntecnnaactvsuneuenssnwsoiweceanectsanwensdicnunsss 2 3 PACKAGE CONTENT LIST cccccsseccenseccenseecensescnnsenenseesenses 2 4 SIMBOLS corma 2 5 GENERAL POWER TOOL SAFETY WARNINGS 0008 3 5 1 VY OPIN AlO T n 3 5 2 Electrical Safely E 3 5 3 Personal E 3 5 4 Power tool use and EE 4 5 5 e VCO P OA wigs tee dasa deg ce viet vag ade denaniar ene cea e enna as acer eanieeenariaees 4 6 SAFETY REG HUEN 4 T BEFORE STARTING WORK cccccccceeseeceeseecenseecensescensesenneesenses 5 7 1 Fitting and changing tools FIG 2 BE 5 7 2 Removing SDS plus tool Fig 3 scsssccsscveneecvssescecisessuennsccrecavavessecssveduncsszerencessenvevessee 5 8 STARTING WORK eege 5 8 1 Switehing ele 5 8 2 Handle ttachment Fig 4 sscscscvssevevescndvsncswsencseusscvcecsedevenctendvenctesensiescevdessesesenesesdves 5 8 3 RE Stop FIO EH 5 8 4 Dust collection device Fig 6 ssccssssccccsnnsccncnnessceennsesseenessssenansessenaasssseneessssenanness 6 8 5 Hammer SIOD occicacsrsne iia i 6 8 6 DAL SUG EEN 6 9 CLEANING AND MAINTENANCE 00 00 ceeeeeeeeceneeeeneeenseseneees 6 10 TECHNICAL DA A WE 6 11 Vleit D 12 WARRANI EE T 13 ENVIRONMENT soasnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnne 7 14 DECLARATION OF CONFO
6. RMITY ccceseeccessecceneesenseeseases 8 Copyright 2014 VARO NV Page 1 www varo com POWE R E L U S POW30543 EN DESIGNED AND MARKETED BY VARO HAMMER DRILL 900W POW30543 1 APPLICATION The hammer drill can be universally used for hammer drilling and chiselling in stone and concrete It is not designed for commercial use instructions carefully before using the appliance Your power tool should only be passed on together with these instructions Cy WARNING For your own safety read this manual and general safety DESCRIPTION FIG 1 2 1 2 Fastening sleeve 3 4 Dust guard 5 Cap for carton brush 6 Depth stop On Off switch 7 Drill stop 8 Auxiliary handle Hammer stop 3 PACKAGE CONTENT LIST Remove all packaging materials Remove remaining packing and package inserts if included Check that the package contents are complete Check the appliance the power cord the power plug and all accessories for transportation damage Keep the packing materials as long as possible till the end of the warranty period Dispose it into your local waste disposal system afterwards AN WARNING Packaging materials are not toys Children must not play with plastic bags Danger of suffocation 1 machine 1 auxiliary handle D 3 SDS drills A 1 dust cover E 2 chisels B 1 depth gauge F 113 mm key chuck adaptor C 1 manual i If any parts are missing or damaged please contact your dealer 4
7. apter plugs with earthed power tools Unmodified plugs and matching outlets will reduce the risk of an electric shock Avoid body contact with earthed surfaces such as pipes radiators kitchen ranges and refrigerators There is an increased risk of an electric shock if your body is earthed Do not expose power tools to rain or wet conditions If water gets inside a power tool it will increase the risk of an electric shock Do not damage the cord Never use the cord for carrying pulling or unplugging the power tool Keep the cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of an electric shock When operating a power tool outdoors use an extension cable suitable for outdoor use Using a cord suitable for outdoor use reduces the risk of an electric shock f operating a power tool in a damp location is unavoidable use a power supply protected by a residual current device RCD Using an RCD reduces the risk of an electric shock 5 3 Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool when you are tired or under the influence of drugs alcohol or medication A moment of inattention when operating a power tool may result in serious personal injury Use safety equipment Always wear eye protection Using safety equipment such as a dust mask non skid safety shoes a hard hat or hearing protection whenever it i
8. fore starting to work always check that the chisel or drill bit is properly locked in the chuck Never start up a hammer tool until it is pressed against a workplace wall ceiling etc When you are finished unplug the hammer drill from the electric supply and remove the chisel or drill bit from the machine Always disconnect the hammer drill from the electric supply before you change a chisel or drill bit Protect your eyes and other workers from flying particles and splinters Wear a helmet Set up partition walls Wear work gloves to protect fingers from bruising and grazing Vibrations can injure the hand arm system Keep exposure to vibrations as short as possible Always lead the mains cable away backwards from the device Store the device where it is inaccessible to children When carrying out work always hold the device with both hands and ensure that you have a stable standing position 7 BEFORE STARTING WORK Examine the place where the device is to be used for hidden electrical cables gas and water pipes using a pipe finding device Before connecting to he mains ensure care that the mains voltage corresponds to the details on the rating plate 7 1 Fitting and changing tools Fig 2 The device is equipped with a SDS plus attachment system Clean tools and grease with a thin layer of machine grease before fitting Pull back fastening sleeve and hold Push and rotate the dust free tool into the
9. jury and Tire when using an electric tool it is imperative to take the following basic safely precautions Read and note these instructions before you use the machine Check the voltage volt marked on the rating plate When using cable drums run all the cable off the drum Minimum conductor cross section 1 0 mm When using the electric hammer drill outdoors connect to the power supply with a type HO7RN F 3G 1 5 mm extension cable and rain water protected plugs in proper working order Make sure of your footing on ladders and scaffolding when drilling tee handed Use a line detector to localize lines in walls with concealed electric water or gas lines Avoid touching live components or conductors Wear ear muffs to protect your hearing Loss of hearing can be a gradual process Wear goggles and use a dust mask on jobs generating dust Do not use in areas where there are vapours or flammable liquids Always pull the plug out or the socket before cleaning or making changes to the machine Protect the power cable from damage oil and acid can damage the cable Never overload the machine Secure all workpieces sufficiently Important It is imperative to follow all national safety regulations concerning installation operation and maintenance Copyright 2014 VARO NV Page 4 www varo com POWERPLUS rouge EN Chisel bits and drill bits may be flung out of the machine accidentally and cause serious injury Be
10. propriate usage use for purposes for which the device is not suitable incompetent usage e g not following the instructions given in the manual inexpert assembly lightning strike erroneus net voltage This list is not exhaustive Acceptance of claims under warranty can never lead to the prolongation of the warranty period nor commencement of a new warranty period in case of a device replacement Devices or parts which are replaced under the warranty therefore remain the property of Varo NV We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained Clean ventilation slots carbon brushes serviced regularly etc Your purchase receipt must be kept as proof of date of purchase Your appliance must be returned undismantled to your dealer in an acceptably clean state in its original blow moulded case if applicable to the unit accompanied by proof of purchase 13 Me Should your appliance need replacement after extended use do not dispose of it with the household refuse but in an environmentally safe way Waste produced by electrical machine items should not be handled like normal c household rubbish Please recycle where recycle facilities exist Check with your Local Authority or retailer for recycling advice Copyright 2014 VARO NV Page 7 www varo com POWE RP L U S POW30543 EN DESIGNED AND MARKETED BY VARO 14
11. s needed will reduce the risk of personal injury Avoid accidental starts Ensure the switch is in the off position before inserting the plug Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely Remove any adjusting keys or spanners before turning on the power tool A spanner or key left attached to a rotating part of the power tool may result in personal injury Do not reach out too far Keep your feet firmly on the ground at all times This will enable you retain control over the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from the power tool Loose clothes jewellery or long hair can become entangled in the moving parts Copyright 2014 VARO NV Page 3 www varo com POWE R E L U S POW30543 EN If there are devices for connecting dust extraction and collection facilities please ensure that they are attached and used correctly Using such devices can reduce dust related hazards 5 4 Power tool use and care Do not expect the power tool to do more than it can Use the correct power tool for what you want to do A power tool will achieve better results and be safer if used in the context for which it was designed Do not use the power tool if the switch cannot turn it on and off A power tool with a broken switch is dangerous and must be repaired
12. tandard K 3 Acoustic pressure level LpA 92 dB A Acoustic power level LwA 103 dB A ATTENTION Wear hearing protection when sound pressure is over 85 d dB A aw Vibration Max 18 7 m s K 1 5 m s te WARRANTY This product is warranted for a 24 month period effective from the date of purchase by the first user This warranty covers all material or production flaws excluding batteries chargers defective parts subject to normal wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc damage or defects resulting from maltreatment accidents or alterations nor the cost of transportation Damage and or defects resulting from inappropriate use also do not fall under the warranty provisions We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Repairs may only be carried out by an authorised customer service centre for Powerplus tools You can always obtain more information at the number 00 32 3 292 92 90 Any transportation costs shall always be borne by the customer unless agreed otherwise In writing At the same time no claim can be made on the warranty if the damage of the device is the result of negligent maintenance or overload s Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inap
13. that the mark T coincides with the arrow on the machine case To reactivate the drilling action the lever selector has to be reset so that the mark tT coincides with arrow pressure will place unnecessary load on the motor Check the drill bits Important When hammer drilling you will require a low pressure Too much regularly Re sharpen or replace blunt drill bits 9 CLEANING AND MAINTENANCE Remove the mains plug from the socket before carrying out any work on the device Keep your machine clean at all times Never use caustic agents to clean the plastic parts At the end of your work to prevent dust deposits you should use compressed air max 3 bar to clean out the ventilation slots Check the carbon brushes regularly dirty or worn carbon brushes result in excessive sparking and speed faults mild detergent on a damp cloth is recommended Water must never come Caution Do not use cleaning agents to clean the plastic parts of the tool A into contact with the tool 10 TECHNICAL DATA Rated Voltage 230 240 V Rated Frequency 50 Hz Rated Power 900 W Rotation speed 850 min Protection class II Drill capacity concrete 26 mm Drill capacity steel 13 mm Drill capacity wood 40 mm Impact rate 4100 min Cable length 2m Chuck type 26mm key chuck Copyright 2014 VARO NV Page 6 www varo com POWE R L U S POW30543 EN DESIGNED AND MARKETED BY VA 11 NOISE Noise emission values measured according to relevant s

Powerplus POW30543 power drill

Contents

Download Pdf Manuals

Related Search

Related Contents