Home

Hikvision Digital Technology DS-9632NI-ST digital video recorder

1. Cancel Figure 140 Migrate Array Interface 4 Select the available physical disk and click OK to confirm the settings 3 There will pop up an attention box with these words Do not unplug the physical disk when it is under rebuilding Click OK to start rebuilding 6 You can enter the Array interface and Virtual Disk interface to check the process of the migration Physical Disk Virtual Disk Firmware test 31 931G3 TA 8 Functional RAID i Migrate Run Figure 141 Array Interface Physical Disk Array Firmware 1006 test Functional RAID 5 Migrate Running 1 Figure 142 Virtual Disk Interface 7 Reboot the device to take effect of the new setting after the migration process finished 123 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 8 Enter the HDD Information interface after rebooting by going to Menu gt System Configuration gt HDD gt HDD Information 9 Select an expandable virtual disk and click the Expand button to expand the capacity of the virtual disk Record Information 150GB Normal Expansion RIV Array 100 00GB Normal RIV Array Figure 143 HDD Information Interface 10 In the pop up message box click OK to start expanding Figure 144 Expand Warning Message 11 After expanding finished the following message box will pop up Click OK to finish the settings Figure 145 Expand Finish Message Note Only migrating from RAID 5 to RAID 5 is supported by the device I
2. Note A physical disk count error attention box will pop up if the number of HDDs you select is not compatible with the requirement of the RAID level 119 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Note The device supports creating at most 8 virtual disks Note It is recommeded to create one virtual disk of an array Rebuilding Array The working status of array includes Functional Degraded and Offline When there is no disk loss in the array the working status of array will change to Functional when the number of lost disks has exceeded the limit the working status of array will change to Offline in other conditions the working status is Degraded When the virtual disk is in Degraded status you can restore it to Functional by array rebuilding Automatically Rebuilding Array Enable Auto rebuild can start rebuilding the array automatically with the hot spare disk when the virtual disk is in Degraded status to ensure the high security and reliability of the data To set auto rebuild 1 Enter the Firmware interface by going to Menu gt System Configuration gt RAID gt Firmware as shown in Figure 133 Physical Disk Array Virtual Disk lobal Hot Spare Array Hot Spare Figure 133 Firmware Interface 2 Check the Auto rebuild box to enable auto rebuild Since the hot spare disk is configured and Auto rebuild function is enabled The hot spare disk will be automatically used for array rebuilding when the st
3. 7 Click Apply to save the settings q gt Configuring OSD Settings On Screen Display OSD settings can be configured in the OSD menu The OSD is shown in each display in Live Feed and Playback mode To configure OSD settings 1 Enter the OSD menu shown in Figure 123 by going to Menu gt Cameras Setup gt OSD 111 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 123 OSD Configuration Menu 2 Select the camera to setup OSD configuration in using the camera dropdown list 3 Configure OSD settings including e Camera Name Name of selected camera Display Name Enable to display camera name in OSD Display Date Enable to display date in OSD Date Format Format of date Time Format Format of time e Display Mode Display style for OSD 4 Using the mouse click and drag OSD elements on preview screen to desired location 5 If the same configurations can be applied to other channels click Copy to copy the settings to other channels 6 Select the ae button to save these settings and select DEA to return to the previous menu Selecting without clicking Apply will quit out of the menu without saving settings Configuring Video Quality Diagnosis Video Quality Diagnosis settings can be enabled on any of the channels on your DVR to diagnose the change of video quality If the video quality turns bad to a certain extent this function will alarm to users To configure video quality diagnosis settings 1 Enter t
4. Enter letters MNO In Playback mode it is used for direct access to playback interface e 7PQRS REC Enter numeral 7 Enter letters PORS Manual record for direct access to manual record interface manually enable disable record e STUV PTZ Enter numeral 8 Enter letters TUV Access PTZ control interface e 9WXYZ PREV Enter numeral 9 Enter letters WXYZ Multi camera display in live view In Playback mode or Menu gt Playback gt Tag playback interface this button can be used to delete the selected tag e 0 A Enter numeral 0 Switch between input methods upper and lowercase alphabet symbols and numeric input In Playback mode this button can be used to add the default tag 5 Jog Shuttle Control The Jog Shuttle control can be used to move the active selection in a menu In the playback mode the outer ring is used to speed up slow down the video The inner ring can be used to jump 30 seconds forward backward in a video In Preview mode it can be used to cycle through different channels 6 Power Button Powers DVR on off 7 USB Ports Connects USB mouse or USE flash memory devices 20 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 13 IR Remote Control The keys on the remote control closely resemble the ones found on the front panel Referring to Figure 13 they include POWER Turn on off DVR DEV Enable Disable Remote Control Alphanumeric Same as Alphanumeric
5. 3 Click Yes to reboot and make the settings effective Click No to cancel the operation 6 After rebooting you can configure local HDD settings To configure local HDD settings by going to Menu gt System Configuration gt HDD gt HDD Information 1 Select a HDD and click to pop up the Local HDD Settings menu as shown in Figure 157 o e oe oe 465 766B Cancel Figure 157 Local HDD Settings 2 Select the HDD Property from R W Read only and Redundancy Read only mode can prevent important recorded files from being overwritten when the HDD becomes full in overwrite recording mode Redundancy mode can ensure high security and reliability by recording the video onto the redundancy HDD and R W HDD simultaneously 3 Select the Group number for the current HDD The default group number for each HDD 1s 1 4 Click the Apply button to save the settings and click OK to the up level menu Note 132 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual At least 2 hard disks must be installed when you want to set a HDD to Redundancy mode and one of them with R W property Disk Clone Internal HDDs can be backup to external eSATA HDDs intact using this function To clone HDD 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Select the Disk Clone tab as shown in Figure 158 HDD Information Record Information Storage Mode Clone Source OMB Not Exist OMB Not Exist Clone Destination SSATA1
6. PTZ a Mn ma 4444 4 4 Figure 85 General Settings of PTZ Configuration Select the General tab Select the camera to configure in the Camera dropdown list Configure PTZ settings including those of Baud Rate Data Bit Stop Bit Parity Flow Ctrl PTZ Protocol and Address according to the parameters of the PTZ camera s If the same configuration can be applied to other PTZ channels click the Copy button Click the Apply button to save the settings m mb Dn To test and verify PTZ settings 1 Enter the PTZ Configuration menu by going to Menu gt Cameras Setup gt PTZ 2 Select the More Settings tab shown in Figure 86 83 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual prog ts Pattern Paren IZ Patrol pao JCI Figure 86 More Settings of PTZ Configuration 3 Select the camera to test in the Camera dropdown list 4 Using the Directional buttons and other PTZ control buttons Zoom Focus Iris the speed of the PTZ movement test the functionality of the PTZ camera If PIZ camera and protocol supports it you may also click the Auto Scan button to test its function PTZ controls buttons are shown in Figure 87 Direction Buttons Auto Sca Zoom Focus Iris Speed Figure 87 PTZ Controls Button 3 If PTZ camera is not working properly make sure PTZ is connected and configured with the correct settings under the General tab Customizing PTZ Presets Patterns a
7. if selected display event information when video signal is abnormal Input Output Video Standard Mismatch If selected display event information when video output standard does not match Recording Capture exception If selected display event information when recording capture exception is detected Video Signal Loss If selected display event information when video signal losses Alarm Input Triggered If selected display event information when alarm input is triggered Video Tamper Detected If selected display event information when detects video tampering Motion Detection If selected display event information when detects motion in video IP Camera Conflicted If selected display event information when IP cameras conflict with others Device Temperature Exception If selected display event information when device temperature is abnormal Hot Spare Exception If selected display event information when hot spare function is abnormal VCA Exception If selected display event information when VCA event is triggered All if selected trigger action when any one of events above is detected 4 Select the Apply button to save the exception settings and select PEs to return to the previous menu Selecting without clicking Apply will quit out of the menu without saving settings Select the Selecting aa button to save the exception settings and select kel to return to the previous menu without clicking Apply will q
8. 9600 Series HDVR NVR User s Manual Searching for POS event files Search and view POS events stored in HDD To search for specified POS events 1 Enter File Management menu by going to Menu gt File Management gt POS Include Cameras A Camera 1 Camera 2 Camera 3 Camera 4 Camera 5 NAAA Camera 6 Camera a Camera 8 a Camera 9 Se Camera 10 Figure 165 POS events a Click the Include Cameras check box to select the channels b Set the search time Start Time and End Time c Select the Match mode during video search Exact match Approximate match Event Flag match and Guide match Exact match 1 Click to select Exact match and then click button Add to add POS video records search condition interface as follows 2 When you set multiple conditions these settings will be displayed in the windows The search results will all fit the settings listed 139 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual v v v v ov v v E ei eS ii ii a E E E E E E E ow O bh WwW nS 1 2 3 4 5 6 T 8 Approximate match Click to select Approximate match and then type in the keywords you want to search The search results are the record POS files that contain the keywords When multiple keywords are typed in POS files with only one of the keywords will also be displayed Approximate matci AE Event Flag match Click to select Event Flag
9. Check the Enable Privacy Mask checkbox to enable privacy mask 4 Up to four privacy masks can be used per camera and are shown using four different colors yellow green blue and grey Using the mouse click and drag out rectangular boxes defining the desired zones 5 You may clear a privacy zone at any time by clicking on the corresponding Clear Zone button or Clear All button to clear all zones 6 If the same settings can be applied to other channels click Copy 7 Select the Apply button to save the privacy mask settings and select R24 to return to the previous menu Selecting BEA without clicking Apply will quit out of the menu without saving settings Configuring Tamper proof Tamper proof detection can be used to recognize if an area of a camera 1s purposely covered and to respond accordingly To configure tamper proof detection 1 Enter the Tamper proof menu shown in Figure 121 by going to Menu gt Cameras Setup gt Tamper proof 109 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 121 Video Tamper proof Detection Menu Select the camera to setup video tampering detection in using the camera dropdown list Check the Enable Tamper proof checkbox Adjust the Sensitivity for video tampering detection Using the mouse select the region on the preview screen for where you would like to enable tamper proof on Press the Clear button to clear region 6 Press the Handing Set button to set up handing method 1 Se
10. Edit the name of the device Device No Edit the number of the device CVBS Output Brightness Adjust the video output brightness Auto Locktime Set the auto lock time of menu Menu Output Mode Select the menu output mode from Auto HDMI VGA and Main CVBS VGA HDMI Synchronous Output Select whether output VGA and HDMI signal simultaneously or not 3 Set the live view interface parameters and event output by going to Menu gt System Configuration gt Live View gt General as shown in Figure 40 44 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual View Channel Zero Encoding Video Output Interface GAJHDMI a 1 m GAHDMI x Os x Figure 40 Live View Menu The settings available to configure for each video output include e Video Output Interface Designates the output including Main CVBS HDMI VGA and Spot Outputl Spot Output2 Spot Output3 and Spot Output4 Live View Mode Designates the display mode for Live Preview e Dwell Time Set the time to dwell between switching of channels when Start Auto switch is selected in Live Preview Enable Audio Output Enable or disable audio output for the selected video output e Event Output Designates the output to show event video e Full Screen Monitoring Dwell Time Set the time to dwell between switching of channels when events occur Setting Camera Order Setting the camera order allows you to logically position cameras for more efficient monitoring o
11. GROUND Ground needs to be connected when device starts up AC 100V 240V AC 100V 240V power supply POWER Switch for turning on off the device 19 USB Universal Serial Bus USB ports for additional devices such as USB Hard Disk Drive HDD RS 232 LAN2 RS485 KB TANG 6 etetett L 30999 till al A a SO S Aerea EEEE o PoSSo09S990899909999809090909 TI O 909695990999999g059g0g0995059 LANI Figure 6 DS 9600NI ST RT i eSATAI ooooo0o00 o0000000 3 su 00000000 00000000 m 00000 EEE 2090909099 VIDEO Lone 0000000 05054050 2650505059 5202990902 a jeta O 15 1 2 3 6 14 8 11 13 Figure 8 DS 7700NI SP VIDEO OUT BNC connector for video output 14 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual AUDIO OUT RCA connector for CVBS and VGA audio output LINE IN RCA connector for audio output RS 232 Interface Connector for RS 232 devices 5 VGA DB9 connector for VGA output Display local video output and menu zi HDMI HDMI video output connector eSATA Connects external SATA HDD CD DVD RM LAN Interface Connector for LAN Local Area Network Termination Switch RS 485 termination switch Up position is not terminated Down position is terminated with 12012 resistance Controller Port D D pin connects to Ta Tb pin of controller For cascading devices the first device s D D pin should be connected with the D D pin of the next device Switch for turning on off the device 1
12. Playback interface as shown in Figure 65 5 21 2014 10 1 G 05 21 2014 10 1 G 05 21 2014 10 1 G 5 21 2014 10 1 05 21 2014 10 1 Figure 65 Tag Playback 65 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 9 10 11 12 13 14 15 Drag the timeline to the place you want to play Click CI to enable or disable the audio Click to play back the pictures in Full Screen mode Click to export selected tags Tam Click to export all tags Click EJ to edit the tag name Click to delete the tag Playing Back POS events 1 Enter the POS menu shown in Figure 66 by going to Menu gt Playback gt POS Approximato map maor J000000 E maoe ZETA O Result w Mm POS1 2014 01 15 14 3 7 06 14 38 55 POS1 2014 01 15 16 45 4 7 16 46 19 Figure 66 POS interface Click on Camera to choose which channel ready to be searched Click on Match box to choose to use Approximate match or Exact match then type in keywords to be searched in right box Approximate match means search results can just match to one of the keywords Exact match means search results should match all the keywords typed in Set the record Start Time and End Time and the Pre play and Post play indicates record length of which will be displayed ahead and post of the record searched Click on Search to get the result Click on the green mark on right of result to get record played in the pink area Note in smal
13. VCA 113 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual P Camera Y Figure 125 VCA Menu 12 Select the camera to setup VCA in using the camera dropdown list 13 Click Enable VCA 14 Press the Handing Set button to set up handing method 3 Select the Arming Schedule tab to set the arming schedule Up to 8 periods can be configured If the same schedule can be applied in other channel click Copy 4 Select the Handing tab to set the actions to take if VCA event is detected 15 Click the Apply button to save the settings Click OK to back to the previous menu 16 If the same settings can be applied in other channels click Copy to copy the same configuration to other channels 17 Click Apply to save the settings 114 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER9 RAID Configuration 115 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Array and Virtual Disk RAID redundant array of independent disks is a storage technology that combines multiple disk drive components into a logical unit A RAID setup stores data over multiple hard disk drives to provide enough redundancy so that data can be recovered if one disk fails The DS 9000HFI 9600NI RT 9600NI XT are capable of realizing RAID settings supporting RAID 0 RAID 1 RAID 5 and RAID 10 The DS 9000HFI 9600NI RT 9600NI XT series can store the data such as record picture log information in the HDD only after you have cre
14. control buttons Click to save pattern To test out your new pattern click o to play and o to stop The PTZ should move as it did during the recording process You may click the stop button at any time to end the pattern Clicking the play button again will start playing the PTZ pattern again at the initial position To customize PTZ patrols 1 2 3 4 ma Enter the PIZ menu by going to Menu gt Cameras Setup gt PTZ Select the More Settings tab as shown in Figure 87 Select a Patrol Number to set from the dropdown list Click Ka to pop up a KeyPoint box and add key point Select a Preset Number from the dropdown list that you would like to add to the patrol Set the duration and speed Click the OK button The Preset Number will be added to the patrol list Repeat steps 4 5 until you have included all the presets you would like to have on the patrol Click the Up and Down button at the bottom of the list to change the order of the presets in the patrol o O To test out your new preset click the Play and Stop button shown as og The PTZ should move through the list of added presets and end the patrol when you click Stop 85 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Alarms and Exceptions Setting up Motion Detection Set up properly using motion detected recording will increase the number of days your DVR is able to record It will only record relevant events rather than everything whic
15. in Figure 98 General DDNS SNMP NAT More Settings Enable Server Authentication E Sender Enable Attached Picture Enable Email Interval Figure 98 Email Configuration Menu 3 In this tab enter all pertinent email information including 92 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Enable Server Authentication Enable if email server requires authentication Enabling Server Authenticating will enable the User Name and Password fields User Name User name to use for server authentication Password Password to use for server authentication SMTP Server Address for SMTP server SMTP Port Port for SMTP server Enable SSL Enable Secure Sockets Layer SSL for out going e mail Sender Name The sender name to use when an e mail is sent out from the DVR Sender s Address The sender s address to use when an e mail is sent out from the DVR Enable Attached Picture Enabling will attach a small picture segment Interval can be set below the Enable Attached Picture checkbox to the out going e mail Receiver Click to edit Receiver Settings Input the receiver s name and address Click Apply to save the settings The e mail address will be added to the Recipients list You can also delete the receiver by clicking Mall Enable Email Interval Enable if need sending email between time intervals The time interval can be set 1 3 5 10 minutes 4 You may now test the e mail settings by clicking the Test
16. match and then type in the attributes of the POS Events you want to be searched including the Filter Event Flag Acknowledge and Notes vent Flag match MAI No Flag Valid Investigate Suspect Guide match Click to select Guide match and then check the boxes according to which kinds of criterion when do searching like item name total etc The POS records matching all or one of these criterion depends on logic choice AND means all and OR means one of them will be displayed 140 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual v Case Sensitive d The search result will show like the interface below 2014 01 15 14 37 06 14 38 55 Confir 2014 01 15 16 45 4 7 16 46 19 4 Unconf 2014 01 16 09 26 45 09 30 06 Confir 2014 01 16 09 33 37 09 34 10 Confir Figure 166 POS search result 1 All results not confirmed will be marked with yellow mark O once you have confirmed the records you can click on this mark and 1t will turn into a which means this incident has been confirmed 2 Click on Event Flag g the following window will pop up 141 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual POS Event Flag No Flag Suspect Figure 167 POS event flag Click on Event Flag to choose kind of Flag which indicates the attribute of this POS record You can also leave notes in Notes box which can be searched by keywords in file management system and playback featu
17. menu 5 If the available space on the storage device 1s adequate select the Export button to begin backup of the selected clips 6 After clips have been backed up you may click the Cancel button to return to the Playback Interface Note If the USB storage device has not been properly initialized and formatted you may click on the Format button to do so Formatting a storage device will permanently delete ALL the files on that device There 1s also NO WARNING MESSAGE after clicking the Format button to format the storage device Please proceed with caution and backup all critical data from the storage device before formatting 71 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Backing up Recorded Files Not only can video clips be backed up full recorded files can also be backed up to a storage medium To back up recorded files l di ui 9 Search for recorded files using the File Management menu See Searching for Recorded Files on Page 60 Select the files you would like to back up by checking the box next to the file You may also check the Channel No box to select all files The total reguired space will be shown next to Total size You can also check the checkbox of Merge files to export Click the Export button this will take you to the Export menu as shown in Figure 71 Mi USE Folder 2012 12 22 1459 20 40 758MB Figure 71 Files Backup Menu In the Export menu connect a USB stora
18. menu without saving Checking the Status of Your DVR The current status of your DVR can be checked at anytime by going to the System Information menu The System Information menu as shown in Figure 19 can be accessed by going to Menu gt System Information Figure 19 System Information Menu 1 Select the Device Info tab to enter the Device Information menu to view the device name model serial No firmware version and encode version as shown in Figure 19 28 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 Select the Camera tab to enter the Camera Information menu to view the status of each camera as shown in Figure 20 You can click the refresh button to renew the information displayed y Camera 01 Enabled Used Notused Not used Used Camera 02 Enabled Used Notused Not used Used Camera 03 Enabled Used Notused Not used Used Camera 04 Enabled Used Not used Not used Used Camera 05 Enabled Used Not used Notused Used Camera 06 Enabled Used Not used Not used Used Camera 07 Enabled Used Notused Not used Used Camera 08 Enabled Used Nat used Not used Used Camera 09 Enabled Used Notused Not used Used Camera 10 Enabled Used Not used Not used Used Camera 11 Enabled Used Not used Notused Used Camera 12 Enabled Used Not used Nol used Used Figure 20 Camera Information Menu 3 Select the Record tab to enter the Record Information menu to view the recording status and encoding parameters of each camera as shown in Figur
19. next four display In a 3x3 mode this will show the next nine display O Start Auto switch gt Stop Auto switch Start Stop Auto Switch Click to start stop auto switch Auto switch will cycle through selected cameras Switching of camera can be based on an individual or multiple cameras Menu Single Screen Multi screen Previous Screen Next Screen Start Auto switch NS Continuous Record Add IP Camera 42 Event Record Output Mode POS Events v Start Recording Click the Continues Record Event Record item This will bring up an attention box shown below If you click yes it will start all day continues event recording of all channels Output Mode Click the Output Mode item This will bring up an Output Mode menu shown below Four modes are available Standard Bright Gentle and Vivid Select one and click the Apply button to save the setting POS events Click the POS events item This will bring up a list of all POS events on this day 42 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual POS1 2014 01 16 15 09 15 15 09 49 A Unconf Filter 1 Before you start Auto switch you should set Dwell Time in Live View setting menu by going to Menu gt System Configuration gt Live View gt General Note After 20 seconds of inactivity the DVR will automatically exit out of the Display menu and go back into the Live Feed mode Note The auto lock menu setting is selected by default meaning th
20. not available when there is still a video clip that has not been saved or cleared Backing up Video Clips After video clips have been selected in the Playback Interface you may back them up to an external USB storage device or DVD writer by going to the Export menu To backup video clips 1 Enter the Clips Export menu shown in Figure 70 by first going to Menu gt Playback In the Playback menu click the Clips Export button m A1 04 02 2013 15 12 01 16 01 31 32 442KB gt ii 7 i ra AH 04 02 2013 12 01 31 13 58 31 76 647KB gt O O Figure 70 Clips Export Interface 70 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 If video clips were successfully saved to the HDD using the Playback Interface they will be listed in the Clips Export interface The camera number as well as the time range and clip size would be listed 3 Select the video clips you would like to back up by checking the checkbox next to the desired to play and review the clip Video clips can be deleted by clicking clips You may also click Ol or by clicking the Delete button to delete the selected clips Check the Channel No box will choose all clips Check the Merge file option to merge all selected video clips and export in one video file 4 Connect at least one USB storage device to the DVR If the device is compatible with the DVR it will automatically be detected Select the backup device from the Device Name dropdown
21. or pause the video In Single Play mode pressing the Enter button will advance the video by a single frame 9 Jog Shuttle Control The Jog Shuttle control can be used to move the active selection in a menu In the playback mode the outer ring is used to speed up slow down the video The inner ring can be used to jump 30 seconds forward backward in a video In Preview mode it can be used to cycle through different channels 10 Power Button Powers DVR on off HIKVISION POWERIZI AWO STATUSI MARAM 7 POrs ig Tuvio wxyz REC PIZ PREV 2 3 4 5 Figure 12 7700 NVR Front Panel Controls The controls on the front panel include 1 Status Indicators Alarm Alarm indicator turns red when a sensor alarm is detected Ready Ready indicator turns blue when DVR is functioning properly Status Status indicator turns blue when DVR is controlled by an IR remote Indicator turns red when controlled by a keyboard and purple when IR remote and keyboard is used at the same time HDD HDD indicator blinks red when data is being read from or written to HDD Modem Reserved TX RX TX RX indictor blinks blue when network connection is functioning properly 2 DVD ROM Slot for DVR ROM 3 Direction Enter Buttons Direction Buttons The Direction buttons are used to navigate between different fields and items in menus In playback mode the Up and Down button is used to fast forward and rewind recorded video The left and Right b
22. settings In PTZ Control mode the MENU WIPER button will start wiper Gf applicable e F1 LIGHT Button The FI LIGHT button when used in a list field will select all items on the list In PTZ Control mode it will turn on off PTZ light e F2 AUX Button The F2 AUX button is used to cycle through tab pages It will also bring up the Channel amp OSD Position settings e MAIN SPOT ZOOM Button The MAIN SPOT ZOOM button is used to switch to the control of spot output In PTZ Control mode it can be used to zoom the camera out e PREV FOCUS Button The PREV FOCUS button is used to switch between single screen and multi screen mode In PTZ Control mode it is used to adjust the focus in conjunction with the A FOCUS button It can also be used to select entire masked areas such as in Motion Detection and Privacy Mask menus 8 Direction Enter Buttons 18 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Direction Buttons The Direction buttons are used to navigate between different fields and items in menus In playback mode the Up and Down button is used to fast forward and rewind recorded video The left and Right button will select the next and previous day of or pause the video In Single Play mode pressing the Enter button will advance the video by a single frame Enter Button The Enter button is used to confirm selection in any of the menu modes It can be used to tick checkbox fields In Playback mode it can be used to play
23. to a USB storage device and imported into another DVR This will allow you to efficiently setup the same configuration on numerous DVRs To export DVR configuration 1 he o gt Enter the Import Export menu shown in Figure 172 by going to Menu gt Maintenance gt Import Export Device Name Figure 172 Import Export Menu Connect the USB storage device to a USB port on the DVR Click the Refresh button The contents of the USB storage device will be shown on the screen You can click the New Folder button to create a new folder Select the location where you would like the configuration to be stored on the USB storage device Click Export to export a configuration file to USB storage device The configuration file will be named devCfg bin Click to exit out of the Import Export menu To import DVR configuration 1 SO al Enter the Import Export menu shown in Figure 172 by going to Menu gt Maintenance gt Import Export Connect the USB storage device to a USB port on the DVR Click the Refresh button The contents of the USB storage device will be shown on the screen Select the configuration file The configuration file is named devCfg bin Click the Import button In the pop up window click Yes to confirm the import and the system will automatically reboot to make it effective Click to exit out of the Import Export menu 148 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Viewing System L
24. view the information of the successfully created array 6 You can select the Virtual Disk tab to view the information of the created virtual disk Note As the default array is RAID 5 at least 3 HDDs must be installed If you install 4 HDDs or above for one touch configuration a hot spare disk will be set as default Note By default one touch configuration creates one array and one virtual disk If the capacity of the array created by one touch configuration is larger than 16TB two arrays and two virtual disks will be created Note By default one touch configuration adopts foreground initialization to initialize the virtual disk By using foreground initialization the virtual disk can be used only after the initialization is complete Manually Creating Array and Virtual Disk You can manually create the array of RAID 0 RAID 1 RAID 5 RAID 10 We take RAID 5 as an example To create the array of RAID 5 Steps 1 Enter the Physical Disk interface by going to Menu gt System Configuration gt RAID gt Physical Disk as shown in Figure 128 2 Click the Create button to enter the Create Array menu as shown below Figure 128 Create Array Interface 117 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual ee za 11 12 13 14 Edit the Array Name Select the RAID Level from RAID 0 RAID 1 RAID 5 and RAID 10 Check the checkbox of corresponding disk to select the Physical Disk that you want to config
25. 0 00 00 Figure 80 Edit User Menu Enter the old password in the Old Password textbox Check the Change Password checkbox Enter the new password in the Password textbox You can also enter the User s MAC or IP Address of the remote PC If it is configured and enabled it only allows the remote user with this MAC or IP address to access the device Click the OK button to save the setting and back to the up level Adding a New Remote Local User You may add up to 31 new users to your DVR To add new users 1 On the User tab shown in Figure 79 click Add to enter Add User interface as shown in Figure 81 O 00 00 00 00 00 Cancel Figure 81 Add User Menu 79 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 Enter the information for new user including User Name Password Level and User s MAC or IP Address Level Set the user level to Guest or Operator Different user levels have different default Operating permission e Guest Guest has the default permission of local log search and remote log search e Operator Operator has the default permission of local log search remote log search two way audio and camera configuration 3 Click the OK button to confirm adding the user Once a new user has been created the fields behind Users will become editable as shown in Figure 82 re cj y i e LI 4 n f Es i a 00 00 00 00 00 00 Figure 82 User Settings Menu Changing the permission of
26. 0090990 VIDEO IN BNC connector for analog video input 12 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual LOOP OUT BNC connectors for video loop output Pe enone SPOT OUT BNC connectors for video output ill biii OUT BNC connector for video output 1 When both HDMI and VGA are connected it is used for live view only 2 When either HDMI or VGA is connected it is used as the spot video output for live view playback recording and PTZ controls 3 When neither HDMI nor VGA is connected it is used as the main video output for live view and menu operations pe a P RS 232 Interface Connector for RS 232 devices 10 DB9 connector for VGA output Display local video output and menu HDMI HDMI video output connector eSATA Connects external SATA HDD CD DVD RM LAN one O Connector for LAN Local Area Network imi Termination Switch RS 485 termination switch Up position is not terminated Down position is terminated with 120Q resistance RS 485 Interface Connector for RS 485 devices T and T pin connects to R and R pin of PTZ receiver respectively Controller Port D D pin connects to Ta Tb pin of controller For cascading devices the first device s D D pin should be connected with the D D pin of the next device A A IN Connector for alarm input E rr A Connector for alarm output 13 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual
27. 0221160616 575KB File 2014 05 08 16 57 48 E ch01_20140221160704 45KB File 2014 05 08 16 57 48 E ch01_20140221160707 55 104KB File 2014 05 08 16 57 55 E ch01_20140307142147 1 014MB File 2014 05 08 16 59 54 E ch01_20140307171923 1 014MB File 2014 05 08 17 01 48 E ch01_20140307204646 1 015MB File 2014 05 08 1 7 03 45 E ch01_20140307233954 1 015MB File 2014 05 08 17 05 42 E ch01_20140308005926 1 015MB File 2014 05 08 17 07 39 E ch01 20140308021906 1 015MB File 2014 05 08 17 09 33 E ch01_20140308033812 1 015MB File 2014 05 08 17 11 30 E ch01 20140308045717 1 015MB File 2014 05 08 17 13 28 el s el el el el el el el s e A MA MA MA MA MA AA MA AA AA AA AME 1 835GB Figure 118 IP Camera Import Export Management Menu Connect the USB storage device to a USB port on the DVR Click the Refresh button The contents of the USB storage device will be shown on the screen You can click the New Folder button to create a new folder Select the location where you would like the configuration to be stored on the USB storage device Click Export to export an IP camera list file to USB storage device Click to exit out of the Import Export menu To import IP camera list 1 nama a Enter the Cameras menu shown in Figure 118 by going to Menu gt Cameras Setup gt Cameras Select the IP Camera Import Export tab as shown in Figure 118 Connect the USB storage device to a USB port on the DVR Cl
28. 26 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Setting Date amp Time It is extremely important to setup the system date and time to accurately timestamp recordings and events To setup date and time as following steps Steps 1 Enter the System Configuration menu by going to Menu gt System Configuration gt General 2 Select the Time Date tab as shown in Figure 17 srr kik YYY MM DD 2014 05 12 1 GMT 08 00 Pacific Time US amp Cil Figure 17 System Configuration Menu 3 The current system time and date as well as the time zone will be displayed Using the directional buttons on the front panel remote or the mouse select the correct date time and time zone 4 Toenable Daylight Savings Time click and check the Enable DST checkbox and there will pop up the DST Setting menu as shown in Figure 18 You can check the Auto DST Adjusting checkbox or manually check the date of the DST period and click the Apply button to confirm the setting Click the OK button to return to the up level menu 27 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Auto DST Adjustment Figure 18 DST Settings Menu 5 To acquire the time and date over an NTP Network Time Protocol Server check the Enable NTP checkbox You can set the interval and enter your own NTP server 6 Click the Apply button to save the settings and click to exit out of the menu Clicking without clicking the Apply button will exit the
29. 4 USB interface Universal Serial Bus USB ports for additional devices such as USB mouse and USB Hard Disk Drive HDD Network Interfaces with Network interface for the cameras and to provide power over RS 485 Interface Connector for RS 485 devices T and T pin connects to R and R pin of PTZ receiver respectively 10 l POE function Ethernet DS 7700NI SP POE NVR only Product Application Diagram 15 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual znaj A as k Na oa pr VGA ra nto Man Montor Aunpcnt Monitor Speaker A sa a Cie ie USB Mo ras kir rame IR Rameja ss i e A li pa o IJ l 3 udih J a Audio Input USB Device y e E Analog Dome Analog Carers IP Dare IP Carora rexe Uny MONA Modes SUPPEL IF Cameras Figure 9 Product Application Diagram Note DS 9600NI ST DS 9600NI RT DS 9600NI XT DS 7700NI SP can only connect network cameras 16 Operating Your DVR There are numerous ways to navigate and operate your DVR You may use the Front Panel Controls the included IR Infrared Remote a Mouse and the Soft Keyboard Using the Front Panel Controls Your DVR NVR comes with built in front panel controls as shown in the following figure HIKVISION 5 3 8 9 10 5 SHOT AUTO DONA FOX EIMENU Fi F2 wrth ALGA AUX 8 5 6 9 7 Figure 11 DS 9600NI XT Front Panel Controls The controls on the front panel include 1 Status Indicators Alarm Alarm indicato
30. Configuring Quota Mode Each camera can be configured with allocated quota for record or picture capture To configure quota mode 1 Enter the quota mode menu by going to Menu gt System Configuration gt HDD 2 Select the Storage Mode tab as shown in Figure 154 HDD Information Record Information Disk Clone Mode P Camera 1 Figure 154 Quota Mode Settings Menu 3 Select the Mode to Quota 4 Select a camera for which you want to configure quota 5 Enter the storage capacity in the text fields of Max Record Capacity GB and Max Picture Capacity GB 6 If the same settings can be applied in other channels click Copy 7 Click the Apply button to save the settings Note If the quota capacity is set to 0 then all cameras will use the total capacity of HDD for record and picture capture Managing HDD Group Multiple HDDs can be managed in groups Video from specified channels can be recorded onto a particular HDD group through HDD settings To managing HDD Group 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Select the Storage Mode tab as shown in Figure 155 3 Select the Mode to Group as show in Figure 156 131 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual HDD Information Record Information Disk Clone v Mode Figure 155 Group Mode Settings Menu 4 Click the Apply button to pop up an attention box as shown below Figure 156 Attention for reboot
31. Enter the HDD menu shown in Figure 148 by going to Menu gt System Configuration gt HDD Record Information Storage Mode Disk Clone Not Exist Local Not Exist Local Figure 148 HDD Management Menu 2 Select the HDD Information tab to check the disk status capacity property type and free space Setting Network HDD Add the allocated DVR Storage Space of NAS or disk of IP SAN to DVR this part will work as network HDD To set a network HDD 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Click the Add NetHDD button to pop up the Add NetHDD menu as shown in Figure 149 127 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual elHDD 1 172 10 14 10 Serie idvrikemi ide box fdvexdan fdvrilylS fdvrilyl4 1 2 3 4 5 6 Figure 149 Add NetHDD Menu 3 Select the number and the type of network hard drive Then enter in the IP address and the directory of network hard drives 4 If you do not know the directory of network hard drives you can click Search after you enter the IP address The network hard drives in this subnet will be listed below Select the one you want to add 5 Click OK to save the settings and return the pervious menu The added hard drives will appear on the list of HDDs 6 You can edit or delete the network hard drivers on the HDD Information menu 128 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Formatting Disk A newly installed hard dis
32. Every POS events will be filtered according to the Descriptions listed in the above interface and then be labeled by the filter Names Click Add to add filters There are three kinds of filter modes 98 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Filter 4 Key Mode ilter 4 String Mode Value Mode 99 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Once selected the filter click Up and Down to move the filter up and down in the list The upper the filter the higher the priority this filter has If a POS event matches some filters it will be labeled by the filter name which is listed on the top Note In More tab check the box Trigger Email enable DVR to send a notifying email to designated email address when a POS event matching this filter happens General Figure 108 Filter Setting f For the AVE protocol click Set to configure AVE settings as follows 1 Protocol Click to select the AVE protocol from the drop down list 2 Address The Address should be exactly the same as the Address of POS terminals 3 Timeout Click to set the Timeout period Click to set the Timeout period When a message is delivered in abnormal status and can t be ended the message will be forced to terminate over the timeout period Cancel Figure 109 POS Setting 100 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTERS Camera Management 101 DS 7700NI SP 9000 9600 Seri
33. H Camara Mi MKYISKOH 182 168 21 4 Camera H HKVISION 197 168 25 IN Camara id MEYISKIH xa a da pot E a da E LES da pa da Figure 113 IP Camera Management Menu The added cameras will display in a list You can also configure the added camera To configure added camera 1 Click O in the added camera list to pop up an Edit IP Camera menu as shown in Figure 114 92 168 254 2 IKVISION Figure 114 Edit IP Camera 2 You can edit the IP Camera Address Protocol Configuration Port and Video Port 3 Click the Apply button to save the settings Click OK to exit this menu Click Cancel without click Apply or OK will back without saving 4 For editing more parameters click the Advance Set button to pop up an Advance Settings window as shown in Figure 115 104 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Password 172 6 23 132 2000 Cancel Figure 115 Advance Settings Menu m Select the Network tab to modify the IP Camera Address and Configuration Port Click Apply to save the settings Select Password tab to change the password Click Apply to save the settings Click OK to exit this menu Click Click to delete camera gt m a gt to get the live view of the camera Note Support third party IP camera PANASONIC SONY AXIS SANYO BOSCH and ACTI 105 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Adding and Removing Analog Cameras Analog cameras can be en
34. HIKVISION DS 9000 ST Series Hybrid DVR DS 9600 ST RT XT Series NVR DS 7700NI SP Series NVR USER S MANUAL Version 3 1 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Hikvision Network Digital Video Recorder User s Manual This manual as well as the software described in it 1s furnished under license and may be used or copied only in accordance with the terms of such license The content of this manual is furnished for informational use only is subject to change without notice and should not be construed as a commitment by Hikvision Digital Technology Co Ltd Hikvision Hikvision assumes no responsibility or liability for any errors or inaccuracies that may appear in the book Except as permitted by such license no part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical recording or otherwise without the prior written permission of Hikvision HIKVISION MAKES NO WARRANTIES EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE REGARDING THE HIK VISION SOFTWARE HIKVISION DOES NOT WARRANT GUARANTEE OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE HIKVISION SOFTWARE IN TERMS OF ITS CORRECTNESS ACCURACY RELIABILITY CURRENTNESS OR OTHERWISE THE ENTIRE RISK AS TO THE RESULTS AND PERFORMANCE OF THE HIKVISION SOFTWARE IS ASSUMED BY YO
35. Inar AA NTN 8 You may now play the selected file by clicking the Play button next to the file 9 The recorded files can also be exported into a USB storage device To export recorded files Figure 162 Search Result Interface 6 605KB 6 64 7KB 6 619KB 6 600KB 6 628KB 6 630KB 6 622KB 6 660KB 6 628KB 6 643KB 6 603KB 6 612KB 6 610KB 6 589KB 6 606KB A na na zra gt A eR RR RB BD OR OR RB OR BR AA s s m s CY a s 4 s s s s 4 connect a USB storage device to the DVR select the record files to export and click the Export button 10 Click the Cancel button to exit out of the File Management menu Searching for Event Files Event recorded files can be searched by criteria in the File Management menu To search for all recorded Event files 1 Enter the File Management menu by going to Menu gt File Management gt Event File 2 Select the Event Type you want to search File type includes Alarm Input and Motion files a TES nom Management Include Cameras Local lt 2 MilLocal lt Local lt filLocal lt Local lt 6 UL ocal lt UL ocal lt 8 fiLocal lt 9 Local lt 10 Figure 163 Event Search 2014 05 13 2014 05 13 vom Be a 00 00 00 3 59 59 137 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 1 2 3 4 5 6 1 1 2 3 4 If you select type Motion First you need to choose the cameras that you would like to inc
36. Live View menu by going to Menu gt System Configuration gt Live View 2 Select the Channel Zero Encoding tab as shown in Figure 42 General View Enable Channel ero Encoding a Full Frame Generali 792i Figure 42 Channel Zero Encoding Menu 3 Check the checkbox to enable channel zero encoding 4 Set the Frame Rate Max Bitrate Mode and Max Bitrate After you set the channel zero encoding you can get a view in the remote client or IE browser of all the channels in one screen Event Hint Event hint allows display the event information in the live view interface when there is an event To setup event hint as following steps Steps 1 Enter the Exceptions menu by going to Menu gt System Configuration gt Exceptions 46 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 Check the checkbox to enable event hint as shown in figure 43 Enable Event Hint Figure 43 Event Hint Setting Menu 3 Select the Event Type Settings to configure The event types include HDD Full If selected display event information when HDD 1s full HDD Error If selected display event information when errors on the HDD are detected Network Disconnected If selected display event information when a network disconnected is detected IP Conflicted If selected display event information if an IP conflicted is detected Illegal Login If selected display event information when illegal logins are detected Video Exception
37. Menu gt System Maintenance gt Network Detection 2 Select the Traffic tab and you can view the sending rate and receiving rate information on the interface as shown in Figure 176 The traffic data is refreshed every 1 second Network Detection Network Stat 40 497 150 JOM Fuledur 20 40 489 1212 ac 1500 10M Hall dup Figure 176 Traffic Detection To configure network detection 1 Enter the Network Detection menu by going to Menu gt Maintenance gt Network Detection 2 Select the Network Detection tab to enter the Network Detection menu as shown in Figure 177 Network Packet Fxport Figure 177 Network Detection 151 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 3 Enter the destination address in the text field of Destination Address 4 Click the Test button to start testing network average delay and packet loss rate The testing result will pop up on the window 5 Click the Status to check the network status To export network packet By connecting the DVR to network the captured network data packet can be exported to USB flash disk SATA eSATA CD RW and other local backup devices Enter the Network Detection menu by going to Menu gt Maintenance gt Network Detection Select the Network Detection tab to enter the Network Detection menu Click the Export button to start exporting After the exporting is complete click OK to finish the packet export as shown in Figure 178 nal een Figure 178 E
38. S 7700NI SP 9000 9600 Series HDVR NVR User s Manual Amning schedule Handling Figure 89 Trigger Channel Settings Menu 1 Select the Trigger Channel tab and check the checkbox of channels which you want the motion detection event to trigger recording Click Apply to save the setting 2 Select the Arming Schedule tab as shown in Figure 90 Choose one day in a week and set an arming schedule If the schedule can also be applied to other days click Copy Click the Apply button to save the settings Iriggar Channel Handling 00 00 2400 00 00 0000 00 00 0000 00 00 00 00 00 00 00 00 00 00 00 00 10 00 00 00 00 00 00 00 o Figure 90 Arming Schedule Settings Menu 3 Select the Handing tab as shown in Figure 91 87 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Ingger Channel Amning Schedule Figure 91 Handing Settings Menu To set other actions including e Full Screen Monitoring DVR will display the video image in full screen when motion is detected e Audible Warning DVR will sound an audio warning if motion is detected in the designated regions of the camera e Notify Surveillance Center DVR will notify surveillance center when motion is detected e Send Email DVR will send an email out to the designated recipients when motion is detected Please refer to configure email settings on Page 91 for details e Trigger Alarm Output DVR will trigger alarm output when motion is detec
39. U THE EXCLUSION OF IMPLIED WARRANTIES IS NOT PERMITTED BY SOME STATES THE ABOVE EXCLUSION MAY NOT APPLY TO YOU IN NO EVENT WILL HIKVISION ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE TO YOU FOR ANY CONSEQUENTIAL INCIDENTAL OR INDIRECT DAMAGES INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION AND THE LIKE ARISING OUT OF THE USE OR INABILITY TO USE THE HIKVISION SOFTWARE EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Preventive and Cautionary Tips Before connecting and operating your DVR please be advised of the following tips e Ensure unit is installed in a well ventilated dust free environment e Unit is designed for indoor use only e Keep all liquids away from the DVR e Ensure environmental conditions meet factory specifications e Ensure unit is properly secured to a rack or shelf Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit e Use the DVR in conjunction with an UPS if possible e Power down the unit before connecting and disconnecting accessories and peripherals e A factory recommended HDD should be used for this device e Improper use or replaceme
40. User The Administrator can change the permission of both guest and operator To change the permission 1 Enter the User menu shown in Figure 75 by going to Menu gt System Configuration gt User 2 Click to enter the Permission interface as shown in Figure 83 Fermission Local Loniguravon Remote Configuration Gamera Configuration x E a a Figure 83 Permission Settings Menu 3 Set the operation permission of Local Configuration Remote Configuration and Camera Configuration for the user 80 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Local Configuration Local Log Search Searching and viewing logs and system information of DVR Local Parameters Settings Configuring parameters restoring factory default parameters and importing exporting configuration files Local Camera Management Enabling and disabling analog camera s Adding deleting and editing of network camera s Local Advanced Operation Operating HDD management upgrading system firmware clearing I O alarm output Local Shutdown Reboot Shutting down or rebooting the DVR Remote Configuration Remote Log Search Remotely viewing logs that are saved on the DVR Remote Parameters Settings Remotely configuring parameters restoring factory default parameters and importing exporting configuration files Remote Camera Management Remotely enabling and disabling analog camera s and adding deleting and editing of network camera s Remot
41. a obok Nea bab akte Rov kelih 117 PC OC Nay O O OE ERA RE NE A a a ates 120 Automatically ReDeS ika 120 Manually Rebuilding ATEN Aa 121 Repar mev TAM DIS ae 121 Pele Array y Vima ld 122 Pel unedne Vital Dis Eoee 122 Delenio EATI asa a A 122 Migraine and ExpandiNS a ee ana a a iaa 123 perdidas a E A N RANE 124 CHAPTER 10 Disk Manacor 126 Manas me DiISks sudeste 127 Check DEE oA remeron ten et penne Menem nT MOD ert Tene rdo 127 Seto DI a A TN 127 Formattan DISE A A N A O 129 E ablins HDD Over wile novine N a ali en iaa 129 Enabling HDD Sleeping Mode ii dd A ee A Dita 130 Enable SALA AOM VE oa eo in ne aa o ee ne aj eb ela 130 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Mana es ATA ia Aita 130 Contiene Quota Mode oa aaa 131 Manasina ADD Gr cados 131 DEREC ai ne o A NA one A E eine na 133 HDO DE CCE no a a 134 SS eee cere A O VA A VO A ER OO A 134 BAG Sector Detecta 134 Manasina o ER OE li ENE uals 136 Searchin tor Recorded UMES a dd Ala dedek ate ene 136 Si a A A le ate 137 Scar tor Capi A PICE ays ela asa rial 138 Searc hino Or POS Event ES eoe 139 lLockmerand Unlocking Recorded Piles iii a 143 CHAPTER 11 DVR Mana em i ka ini ANA AA ANA 144 DVI IT VIS to a Na 145 I peradins the Systema EA sige A A A MIN ba O coa 145 Restoring Del du Semin es va a ae A o de ae vele ele i 146 Exporting amp Importing Contisucdtion savi ee a AV oi 148 VTE WW 1S SEC HO areal he seas O E iat hoa saved NE S AE oe A SN o kn 149 le S
42. a oja k dee CUON O ONE E E 151 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER1 Introduction DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Overview Thank you for your purchase of DS 7700NI SP 9000 9600 Series Hybrid Digital Video Recorder HDVR NVR To get detailed information about the HDVR NVR please read through the Installation s Manual and this User s Manual thoroughly The DS 7700NI SP 9000 9600 series HDVR NVR is a new generation product developed by HIKVISION Built on an embedded platform and combining the latest advanced H 264 video encoding and decoding technologies the DS 7700NI SP 9000 9600 series HDVR NVR contains the perfect combination of rock solid reliability and high performance Co JA gt JA JAMA JAMA gt JA lt JAM JA lt JAM JR SJ JA A JA JA JA Figure 3 DS 7700NI SP Series NVR Product Features Compression Connecting the network cameras network dome and DVS 6 H 264 video compression with high reliability and superior definition O Each channel supports dual stream O Up to 64 network cameras can be added DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Independent configuration for each channel including resolution frame rate bit rate image quality etc The video input output quality is configurable Each channel supports two kinds of compression parameters the continuous and event which can be configured locally and remotely Encoding for b
43. abled and disabled in the Cameras menu To manage analog cameras 1 Enter the Cameras menu by going to Menu gt Cameras Setup gt Cameras 2 Select the Analog tab as shown in Figure 116 PER S Ja IP Camera IP Camera Import Export Analog Cameras List Camera 02 Enable Camera 03 Enable Camera 04 Enable Camera 05 Enable Camera 06 Enable Camera 07 Enable Camera 08 Enable Figure 116 Analog Camera Settings Menu 3 To enable a camera check the box of the corresponding camera number To disable a camera uncheck the box You may also check and uncheck Analog to enable and disable all cameras 4 Select the Apply button to save the camera settings There will pop up an Attention message box as shown in Figure 117 Attention Figure 117 Enable Disable Analog Camera Attention Message 5 Click Yes to reboot and make the settings effective Click No to cancel and back to the pervious menu Note Enable or disable analog cameras function is only for 9000 series Hybrid DVR device 106 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual IP cameras List Import and Export The added IP camera list can be imported and exported in the Camera menu To export IP camera list 1 Enter the Cameras menu by going to Menu gt Cameras Setup gt Cameras Select the IP Camera me o m 7 Import Export tab as shown in Figure 118 IP Camera PoE Information Device Name SB Flash Disk 1 2 y E ch01_2014
44. ack of marked clip Full Screen Enter full screen playback mode Searching for Recorded Files The Playback Interface allows for easy searching of recorded files To search for recorded files using the Playback Interface 1 2 3 5 Enter the Playback menu shown in Figure 57 by going to Menu gt Playback gt Record Select the channel to search for recordings on Select the date to search for recordings on using the calendar The system date is shown on the left of the calendar You may change the month and year of the calendar by clicking the left and right arrows next to the month and year Dates with recordings in the selected month and channel are displayed in light blue Dates without recordings are light gray The active selected date is lighted up with a green box Click on the desired date that is highlighted in light blue to search for recordings If recordings exist the timeline will be filled with blue bars to designate recorded files The playback marker indicated by a green vertical line will automatically jump to the beginning of the earliest recordings for the selected date The marker can be moved to any other location by clicking on the desired sa on the blue bars or drag it Select in the Playback Controls to start playback of the recording Playing Back Recorded Files After finding the recordings you would like to play back you may use the Playback Controls to navigate through the recording The controls fou
45. arm the DVR in Preview mode e REC SHOT Button The REC SHOT button is used to enter the Quick Schedule Recording interface If used when controlling a PTZ pressing the REC SHOT button and then a Numeric button will call a PTZ preset e PLAY AUTO Button The PLAY AUTO button is used to enter the Playback menu It is also used to turn audio on off in the Playback menu and auto scan in the PTZ Control menu e ZOOM Button The ZOOM button is used to zoom the PTZ camera in when in the PTZ Control menu e A FOCUS Button The A FOCUS button is used to adjust focus in the PTZ Control menu It is also used to switch between input methods upper and lowercase alphabet symbols and numeric input It can also be used to clear entire masked areas such as in the Motion Detection and Privacy Mask menus e EDIT IRIS Button The EDIT IRIS button is used to edit text fields When editing text fields it will also function as a Backspace button to delete the character in front of the cursor On checkbox fields pressing the EDIT IRIS button will tick the checkbox In PTZ Control mode the EDIT IRIS button opens up the iris of the camera In Playback mode it can be used to generate video clips for backup e MENU WIPER Button Pressing the MENU WIPER button will return the user to the Main menu after successful login Pressing and holding the button for 5 seconds will turn off audible key beep The MENU WIPER button will also bring up Sensitivity Interface
46. ated the virtual disk or you have configured network HDD refer to Setting Network HDD Our device provides two ways for creating the virtual disk including one touch configuration and manual configuration The following flow chart shows the process of creating virtual disk Note Please install the HDD s properly and it is recommended to use the same enterprise level HDDs including model and capacity for array creation and configuration so as to maintain reliable and stable running of the disks One touch Configuration You can quickly create the disk array and virtual disk through one touch configuration By default the array type to be created is RAID 5 Steps 1 Enter the Physical Disk interface by going to Menu gt System Configuration gt RAID gt Physical Disk as shown in Figure 126 Array Virtual Disk Firmware 931 51GB Norm al Functional ST310005765V 465 66B Normal Functional 5135004 105V 931 51GB Normal Functional ST310005265V Figure 126 Physical Disk Settings Menu 2 Click the One touch Config button to pop up a One touch Array Configuration box as shown below 116 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 127 One touch Array Configuration 3 Edit the array name in the Array Name text box and click OK to start configuration the array 4 There will pop up an Attention box when the array configuration is completed Click OK to finish the settings 3 You can select the Array tab to
47. ation 2013 10 22 09 00 53 Start Recording information 2013 10 22 09 00 53 C information 2013 10 22 09 00 53 Information 2013 10 22 09 00 53 9 information 2013 10 22 09 00 53 information 2013 10 22 09 00 53 Start Recording information 4317 99 NANNA Start Recording gt e a gt ih H gt gt Figure 174 Log Search Results 6 Click M4 under the Detail item to view the detail information as shown in Figure 175 DO ON OO 2013 10 22 09 00 53 information Start Recording ormaren a IE NI A er rar vorov vrne information 2013 10 22 00 53 Start Recording 9 information 2013 10 22 09 00 53 Start Recording infarmahan M1310 99 nannsa2 Start Racnrdina b b gt gt gt gt gt gt HA Figure 175 Log Information 7 Click Previous Next to view the previous next log information 8 Click OK to back to the previous menu 9 If applicable you may also view the associated video to the selected log entry by clicking 10 Log files can also be exported onto a USB storage device To export a log file connect a USB storage device to the DVR select the log files to export and click the Export button 11 Click i a to exit out of menu 150 Network detection You can view the network traffic to obtain real time information and connecting status of your DVR To view network traffic 1 Enter the Network Detection menu by going to
48. ation can be sent to the remote host 11 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Remotely start stop recording Remotely start stop alarm output Upgrade by remote FTP server is supported Remote PTZ control Remote JPEG capture Two way voice talk and voice broadcasting Embedded WEB server Support ANR Automatic Network Replenishment technology Support Virtual Host function Development Support 6 SDK for Windows and Linux system O Source code of application software for demo O Development support and training for application system Rear Panel bl GO OO VIDEO SP o T OUT OO vioo Lauwo OUT OUT 0 xX gt C AS stike ej DO ejo A tl LINE IN 6 5 D Ic G Hoo N zle RS 232 VGA HDMI NA LAR iN U 56 ll 12 13 14 15 Figure 4 DS 9100 9000HFI ST SATA ee e PA OU a CO a AR om ooo es E L 0 65555555 eee in e a 2 3 4 5 6 9 7 10 111219 13 14 15 Figure 5 DS 9000HWI ST DS 9000HFI RT No Support N 1 hot spare function NVR and H DVR support this function 990099000000r OOGSOOOOSOOOS kiti o 02020 ogo o 02080209596 95950505060505060208080 0 0 0 0802809620262909620 030209 OGOSo8o8o802o202680 o 020 020 0999999999995 999699959 4 o yy 4 99909009 0269525959505250 5950505 02620962596952595952909020 02080908080209520208026 0 9 9 0 0 009090
49. atus of the array is Disk Loss You can check the rebuild status by going to Menu gt System Configuration gt RAID 1 Select Array tab to view the array rebuilding status Physical Disk Virtual Disk Firmware test wazia 178 Disk Loss RAID 5 Rebuild Running Figure 134 Array Interface 2 Select Virtual Disk tab to view the virtual disk rebuilding status Physical Disk Array Firmware 931G test Degraded RAID 5 i Rebuild Running 0 Figure 135 Virtual Disk Interface Note 120 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual If there is no hot spare disk after rebuilding it is recommended to install a HDD into the device and set is as a hot spare disk to ensure the high security and reliability of the array Manually Rebuilding Array If you do not enable the Auto rebuild in Firmware interface or the hot spare disk has not been configured you can rebuild the array manually to restore the array when the virtual disk is in Degraded status To manually rebuilding array 1 Enter the Array interface by going to Menu gt System Configuration gt RAID gt Array tab 2 Click 44 to pop up the Rebuild Array box Cancel Figure 136 Rebuild Array Interface Select the available physical disk and click OK to confirm to rebuild the array There will pop up an attention box with these words Do not unplug the physical disk when it is under rebuilding Click OK to start rebuilding 3 You can enter the Array Setti
50. be configured for each day Select recording type under Type for selected day of the week Recording type includes Continuous for continuous recording or Event for recording when an event is triggered 1 e from detected motion for the selected time period Select the Add button to add time frame to schedule The newly added time frame will appear in the schedule on the right You can click EJ to delete the selected time period on the right Continuous recordings are shown in blue on the schedule while event recordings are shown in yellow An example of this can be seen in Figure 48 IP Gamerad MO Mon CU Coi Ste ro he 010 0000 00 Mon OG 00 1 200 Figure 48 Record Schedule Configuration Example If there are scheduling errors detected error messages such as those shown in Figure 49 will appear Figure 49 Schedule Configuration Error Messages Repeat the above steps to set recoding schedule for other days in the week Edit the schedule Click the Edit button on the bottom right to pop up the Edit Schedule menu as shown in Figure 50 52 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 3 4 5 6 1 8 1 2 3 Schedule Figure 50 Edit Schedule Menu Select a day from Monday to Sunday Setup time periods for schedule If the All Day checkbox is checked recording will occur over the entire day To setup multiple time periods uncheck All Day and enter the Start End Time for the select
51. button 5 Select the SM button to save the e mail settings and select Ba to return to the previous menu Selecting without clicking Save will quit out of the menu without saving settings Configuring Hot Spare Settings If there are a group of DVRs working in the same net we can use the hot spare function to increase the reliability of the whole system To setup hot spare settings 1 Enter the Hot Spare Configuration menu by going to Menu gt System Configuration gt Hot Spare As shown in Figure 99 Figure 99 Hot Spare Configuration Menu 93 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 Choose the work mode of current DVR Normal Mode indicates this DVR work as usual way Hot Spare Mode means this DVR work as a hot spare device 3 Once selected the normal mode enter all the information required in the Enable tab including IPv4 address of the hot spare device and the Password of the hot spare device 4 Select the Apply button to save the e mail settings and select S to return to the previous menu Selecting without clicking Save will quit out of the menu without saving settings Note NVR and H DVR support this function Configuring POS Point of Sale Settings The POS feature supports display POS information on corresponding channels in preview and playback To setup POS settings 1 Enter the POS configuration menu by going to Menu gt System Configuration gt POS 091 CP Receive
52. button to turn on and off audio during playback Click to enable digital zoom Once enabled the regular recorded feed will be shown in the lower right corner while the zoomed in view will be shown on the full screen The zoomed in region may be changed by moving the red rectangle in the regular recorded feed window Click and manage it Click to control playback Playing Back Multiple Channels You may also playback recordings from multiple channels simultaneously To playback recordings from multiple channels 1 Search and select recording to playback in the Playback Interface 2 Enter into Full Screen mode shown in Figure 59 by clicking the Full Screen button 61 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 3 In Full Screen mode you may select additional channels to playback by clicking the checkbox next to the desired camera in the Channel Selector panel Playback will begin simultaneously on the selected channels 4 You may stop playback on any of the channels by un checking the checkbox next to the channel 3 You can also select recording in Full Screen mode by double click the date on the calendar Note Up to 16 channels can be played back at the same time Smart Playback Search and view events records in HDD more efficiently Playback will be fast in non event period and will be normal speed during event period To do Smart Playback 1 Enter the Smart interface shown in Figure 60 by going to Me
53. buttons on front panel EDIT Same as JKL EDIT button on front panel A Same as A FOCUS button on front panel REC Same as REC SHOT button on front panel PLAY Same as MNO PLAY button on front panel INFO Same as ZOOM button on front panel VOIP Same as MAIN SPOT ZOOM button on front panel 10 MENU Same as MENU WIPER button on front panel 11 PREV Same as PREV FOCUS button on front panel 12 DIRECTION ENTER Buttons Same as DIRECTION ENTER buttons on front panel 13 PTZ Same as PTZ IRIS button on front panel 14 ESC Same as ESC button on front panel 15 RESERVED Reserved 16 F1 Same as FI LIGHT button on front panel 17 PIZ CONTROL Buttons Buttons to adjust the iris focus and zoom of a PTZ camera 18 F2 Button Same as F2 AUX button on front panel OPBAaARU NE 21 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Aim the remote control at the IR receiver located at the front of the unit to test operation If there is no response 1 Using the front control panel or the mouse go into Menu gt System Configuration gt General gt More Settings 2 Check and remember DVR ID The default ID is 255 This IDY is valid for all IR controls 3 Press the DEV button on the remote 4 Enter the DVR ID from step 2 5 Press the ENTER button on the remote control If the Status indicator on the front panel turns blue the remote control is operating properly If the Status indicator does not tur
54. ce center sending email and alarm output O Automatic restore when system is abnormal Support push alarm notification Other Local Functions O Users can operate device by front panel mouse remote control and control keyboard 6 Three level user management admin user can create many operating accounts and define their Operating permissions which includes the limit to access any channel O Operation alarm exceptions and information log recording and searching import and export device configuration information Network O 2 self adaptive 10M 100M 1000M network interfaces 1 network interface for DS 7700NI SP and various working mode is configurable multi address load balance network fault tolerance etc IPv6 is supported TCP IP protocol DHCP DNS DDNS NTP SADP SMTP SNMP UPnP NES and iSCSI are supported TCP UDP and RTP for unicast Auto manual port mapping and automatically discovered by UPnP Remote web browser access by HTTPS ensures high security Remote search playback download locking and unlocking the record files and downloading files broken transfer resume Remote parameters setup remote import export of device parameters Remote viewing of the device status system logs and alarm status Remote keyboard operation Remote locking and unlocking of control panel and mouse Remote HDD formatting and program upgrading Remote system restart and shutdown Alarm and exception inform
55. ck the refresh button to renew the information displayed IPv4 Address 192 168 0 64 IPv4 Subnet Mask 255 255 255 0 IPv4 Default Gateway 192 168 0 1 IPv6 Address 1 1080240 48t feb 7 9f3a 64 IPv6 Address 2 IPv6 Default Gateway Preferred Tver 0000 Alternate DNS Server 0000 Enable DHCP Disabled Mam NIC LAN1 Figure 23 Network Information Menu 6 Select the HDD tab to enter the HDD Information menu to view the HDD status free apace capacity etc as shown in Figure 24 You can click the refresh button to renew the information displayed 30 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Normal 465 7668 14908 Figure 24 HDD Information Menu 31 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER3 Live Feed 32 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Watching a Live Feed The Live Feed mode is automatically started after the DVR boots up It is also at the very top of the menu hierarchy thus hitting the ESC button multiple times depending on which menu you re on will bring you to the Live Feed mode Understanding Live Feed Icons There are multiple icons on each display in Live Feed mode to indicate different camera status and settings These icons include Event Icon Indicates video loss or tampering motion detection and or sensor alarm Y Record Icon Indicates the current channel is recording The recording may have been started from a schedule and o
56. cters can be displayed on each line and the exceeding content will be automatically displayed at the next line Note Hex stands for Hexadecimal which is a numeral system based on 16 common symbols 0 9 and A F or a f Click Hex check box to enable Hexadecimal mode 4 Case Sensitive Click check box to differentiate between capital and lowercase letters 5 Timeout Click to set the Timeout period When a message is delivered in abnormal status and can t be ended the message will be forced to terminate over the timeout period The default timeout period is 60s 6 Extra Line s Click to select extra lines from 0 to 10 lines to be displayed on the video after detecting of End Line Identifier string This option is designed for transaction data which ends with dynamic information such as transactional time etc which could not be set as End Line Identifier string yet is still required to be displayed 97 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual General Filter Figure 106 POS Setting 7 Ignore Line Click to select how many strings of transactional data shall be ignored to display on the video Maximum is four And then click lower blank to edit the ignore character through the virtual keyboard as follows 8 Filter Filter helps to categories different POS events you are interested General More Setting Filter 1 Total Filter 2 water gt 50 00 Filter 3 Change E E E Figure 107 POS Setting
57. d it or directly edit it on the left side of the interface 6 Click the Upgrade button to upgrade the firmware of added IP cameras in local menu 7 Click Protocol to pop up a Protocol Management box as shown in Figure 111 to edit the protocol parameters 102 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Costume Protocol Custom Protocol 1 o Rise Rise Mi TI e 7 Figure 111 Protocol Management Settings Menu 8 If the IP camera is not online you can enter the IP address protocol configuration port camera user name and other information on the left side of the interface 9 Click Add to add this camera You can also use the right click menu during live view to quickly add IP cameras To quickly add IP cameras 1 Enter the live view menu and right click the mouse as shown figure 112 in then choose the Add IP camera option Menu Single Screen Multi screen Previous Screen Next Screen start Auto switch Start Recording Output Mode ft POS Events Figure 112 Right Click Menu 2 Click Auto to automatically detect and add IP cameras Or click Manual to manually manage the IP cameras as shown in figure 113 103 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual En 10 13 6251 i BackDoaar HK ISKOIH 197 168 241 4 NI Camara Ki HKVISKIH 107 168 4 5 dd PGamerah MEYISKIH 197 168 21 6 NI Camara fi HEK YHON 17 168 eT oo PCamerd W MEYISKIH 182168 21 5 Camera OY HMKVISKIH 102 168 44 9 4 I
58. d like to select video clips from See Searching for Recorded Files on Page 60 Video clips can only be selected in single playback mode 69 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 10 11 Note Select the starting position of the video clip by clicking the desired location on the blue recordings bar Click the Start button Select the i y oai of the video clip the same as starting position You can click Click the Stop button The selected video clip time range will be shown at the bottom of the Playback Interface as seen in Figure 69 to zoom in zoom out the timeline and select the exactly time Clip Time 10 57 00 10 57 55 Figure 69 Video Clip Time Range You may play the video clip using the Play button or use the arrow keys which are shown below the timeline to progress through the video one second minute or hour at a time Click the Save button to save clip to the DVR Clip must be first saved to the DVR before it can be backed up to an external USB storage device or to a DVD writer Clicking the Clear button will remove the video clip Repeat steps 2 10 to select additional clips If you would like to backup video clips at this point click the Clips Export button The Play Save and Clear buttons are not available unless a completed video clip is selected A completed video clip has a start and end point marked by using the Start and Stop button Note The Start button is
59. down your DVR To shut down your DVR Option 1 1 Press and hold the POWER button on the front panel for 3 seconds 2 Enter the administrator s username and password in the dialog box for authentication 3 There will pop up an attention box 4 Click the Yes button to shut down your DVR and click the No button to cancel Option 2 1 Shutdown your DVR by going to Menu gt Maintenance click KI in the lower left corner to pop up the Shutdown menu as shown in Figure 16 25 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Cancel Figure 16 Shutdown Menu 2 Select the Shutdown button 3 Click the Yes button Note Do not press the POWER button again when the system is shutting down Rebooting Your DVR While in the Shutdown menu Figure 16 you may also reboot your DVR by clicking Reboot Locking Your DVR Locking your DVR will return you to the Live Feed mode which will require the correct user name and password to exit out of it and do operation You have two methods to lock your DVR e Enter the Shutdown menu by going to Menu gt Maintenance gt Shutdown and click the Lock button e Click on the lower left corner of Menu interface to lock your DVR Note You can also set auto lock time to lock the menu for a certain period of time inactivity Enable auto locking by going to Menu gt System Configuration gt General gt More Setting and select auto lock time in the Auto Locktime dropdown list
60. e 21 You can click the refresh button to renew the information displayed Video amp Full Frame 81 1792 704 480 4CH Continuous Continuous No Video amp Full Frame 82 1192 104 A3D0 ACIF Continuous Continuous No Video amp Full Frame 81 1792 704 480 4CIF Continuous Continuous No Video amp Full Frame 80 1792 704 480 4CIF Continuous Continuous Video amp Ful Frame 81 179 104 480 4C1F Continuous Continuous No Video amp Full Frame 81 1792 104 48 CIF Continuous Continuous Video amp Full Frame 80 1792 Continuous Continuous No Video amp Full Frame 82 1792 04 48 C Continuous Continuous No Use Video amp Full Frame 81 1792 104 480 4C4F Continuous Continuous No Use Video amp Full Frame 81 1192 104 430 4C04F Continuous Continuous Use Video E Full Frame 30 1792 104 480 4C4F Continuous Continuous No Used Video amp Full Frame 80 1792 704 48014CHF Continuous Continuous No Figure 21 Record Information Menu 29 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 4 Select the Alarm tab to enter the Alarm Information menu to view the alarm information as shown in Figure 22 You can click the refresh button to renew the information displayed Local lt 1 Local lt 2 Local lt 3 ocal lt 4 ocal lt 5 L L L l Local lt 8 l l L L Figure 22 Alarm Information Menu 5 Select the Network tab to enter the Network Information menu to view the network information as shown in Figure 23 You can cli
61. e Admin password must be enter to exit out of the Live Feed into the Main Menu Configuring Live Feed Displays Live Feed displays can be customized to your own needs To customize display settings 1 Set language CVBS output standard resolution and so on by going to Menu gt System Configuration gt General gt Display as shown in Figure 38 Time Date More Settings TSG 1280 1024 60H Figure 38 Display Menu The settings available to configure in this menu include e Language The default language used is English 43 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CVBS Output Standard Select the output standard to NTSC or PAL which must be the same with the video input standard Resolution Select the appropriate resolution Mouse Pointer Speed Set the speed of mouse pointer and 4 levels are configurable Double Click Speed Set the double click speed of mouse Enable HDMI Resolution Auto Automatically adjust the resolution of HDMI output based on display Enable Password Require password when access menu in preview mode 2 Set device name device no CVBS output brightness auto lock time menu output mode and VGA HDMI synchronous output by going to Menu gt System Configuration gt General gt More Settings as shown in Figure 39 TimefDate Display Embedded Net DVR ZE Figure 39 More Settings Menu The settings available to configure in this menu include Device Name
62. e HDD sleeping mode 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Select the Record Information tab as shown in Figure 152 3 Check the Enable HDD Sleeping checkbox 4 Click the Apply button 5 Click to exit Enabling eSATA Auto Archive Enabling eSATA Auto Archive will allow DVR automatically backup record files on external eSATA devices according to a preset schedule To enable eSATA Auto Archive 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Select the Record Information tab as shown in Figure 153 3 Click on Setting button as shown below Y 00 00 00 dotat A a a a E a La ka a m ES a a ES Figure 153 Auto Archive Settings Menu Check the Enable Archive checkbox Set the Archive Time Check the channels needed to be backup Click Apply button Click 5 to exit Managing eSATA When there is an external eSATA device connected to DVR you can configure eSATA for the use of Record Capture or Export To manage eSATA 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Select the Record Information tab as shown in Figure 153 3 Select the eSATA Usage to Record Capture or Export from the dropdown list Se 130 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual e Export Use the eSATA for backup e Record Capture Use the eSATA for record capture 4 Click the Apply button to save the settings
63. e Serial Port Control Configuring settings for RS 232 and RS 485 ports Remote Video Output Control Sending remote button control signal Two Way Audio Realizing two way radio between the remote client and the DVR Remote Alarm Control Remotely arming notify alarm and exception message to the remote client and controlling the alarm output Remote Advanced Operation Remotely operating HDD management upgrading system firmware clearing I O alarm output Remote Shutdown Reboot Remotely shutting down or rebooting the DVR Camera Configuration Local Video Export Locally exporting recorded files of the selected camera s Local Playback Locally playing back recorded files of the selected camera s Local PTZ Control Locally controlling PTZ movement of the selected camera s Local Manual Operation Local manual operation of the selected camera s Remote Live View Remotely viewing live video of the selected camera s Remote Playback Remotely playing back recorded files of the selected camera s Remote PTZ Control Remotely controlling PTZ movement of the selected camera s Remote Manual Operation Remotely manual operation of the selected camera s 4 Click the Apply button to save the parameters Note If you forget the password to your DVR contact your supplier with the serial number of your DVR to obtain a secure code to reset your DVR Note User settings only appear on the list of System Configuration when
64. e USB storage device to a USB port on the DVR Click the Refresh button The contents of the USB storage device will be shown on the screen Select the firmware file The firmware file is named digicap mav Click the Upgrade button to upgrade the DVR The DVR will automatically reboot after the upgrade is completed If you do not wish to upgrade at this point click the Cancel button mimo To update the system firmware from FTP 1 Enter the Upgrade menu by going to Menu gt Maintenance gt Upgrade 2 Select the FTP Upgrade tab as shown in Figure 170 145 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Local Ups ad Figure 170 FTP Upgrade Menu 3 Enter the FTP Server Address 4 Click the Upgrade button to upgrade the DVR The DVR will automatically reboot after the upgrade is completed Restoring Default Settings To restore factory default settings to your DVR 1 Enter the Factory Default menu shown in Figure 171 by going to Menu gt Maintenance gt Factory Default 146 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 171 Factory Default Menu 2 Select the OK button to restore factory defaults or select REA to return to the previous menu Note Network information such as IP address subnet mask and gateway will not be restored 147 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Exporting amp Importing Configuration Configuration information from your DVR can be exported
65. eal RV 2014 05 13 00 00 00 amaosa pasosa L Figure 161 File Search Menu 2 Select the cameras that you would like to include in the search Analog cameras are listed on the first row preceded with the letter A If you would like include all analog cameras in the search check the Analog checkbox Digital cameras are listed on the second row preceded with the letter D If you would like include all IP cameras in the search check the IP Camera checkbox Select the Video Type Video type includes Continuous Event Manual and All Select the File Type File type includes Locked Unlocked and All files Select the start time and the end time Click the Search button A search result box will pop up as shown in Figure 162 A list of results with your search criteria will be shown at the bottom of the menu ae ee 136 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Y A Y A2 n A3 KA AB MA NO A8 AQ 2012 12 20 10 57 04 1 1 07 02 2012 12 20 10 5 7 04 11 07 02 2012 12 20 10 5 7 04 11 07 02 2012 12 20 10 57 04 11 07 02 2012 12 20 10 577 05 11 0 7 04 2012 12 20 10 5 7 05 11 07 04 2012 12 20 10 57 05 11 07 04 2012 12 20 10 57 05 11 07 04 2012 12 20 10 57 05 11 07 04 A10 2012 12 20 10 57 05 11 07 04 A11 2012 12 20 10 57 05 11 07 04 A12 2012 12 20 10 57 05 11 07 04 A13 2012 12 20 10 57 05 11 07 04 A14 2012 12 20 10 5 05 110 04 A15 2012 12 20 10 57 05 11 07 04 8 AA AAAA AA NA AA r
66. ed day You can select recording type for each period Click the Apply button to save the settings Repeat the above steps to set record schedule for other days in this week If the schedule can also be applied to other days click the Copy button to pop up a Copy to box as shown in Figure 51 Figure 51 Copy to Check the corresponding checkbox of the day to copy the record schedule to Click the OK button to save the settings and back to upper level menu or click the Cancel button to back without saving Click the Apply button to save the settings and click OK to exit Draw the schedule Click ee ee A to select a recording type None means no recording Use the mouse to drag and draw time periods in the assigned area Up to 8 discontinuous periods can be configured for each day Repeat the above steps to set record schedule for other days in the week 53 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 4 Click the Apply button to save the settings or click koli to exit without saving 6 Repeat the above steps to set record schedule for other channels If the same schedule can be applied to other channels click the Copy button to pop up a Copy to box as shown in Figure 52 Figure 52 Copy to 7 Check the corresponding checkbox of other channels to copy the record schedule to 8 Click the OK button to save the setting and back to upper level menu or click the Cancel button to back without saving 9 Click the Appl
67. el Settings Menu 1 Select the Trigger Channel tab and check the checkbox of channels which you want the alarm to trigger recording Click Apply to save the settings 89 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 Select the Arming Schedule tab Choose one day in a week and set an arming schedule If the schedule can also be applied to other days click Copy Click Apply to save the settings 3 Select the Handing tab which is same as Figure 92 to set other actions Click Apply to save the settings 4 Select the PTZ Linking tab as shown in Figure 95 to set the PTZ actions only if a PTZ camera is configured on the DVR Only one PTZ action can be selected per alarm input Irigger Channel Arming Schedule Handling Figure 95 PTZ Linking Settings Menu 8 If the same settings can be applied to other alarm inputs click the Copy button to copy the settings to others 9 Click Apply to save the settings 10 You can check the alarm input status in the Alarm Input Status list on the Alarm Input Interface Configuring Alarm Outputs Trigger an alarm output when an alarm is triggered To configure alarm output 1 Enter the Trigger menu by going to Menu gt Recording Configuration gt Trigger 2 Select the Alarm Output tab as shown in Figure 96 Figure 96 Alarm Output Settings Menu 3 Select the Alarm Output No in the dropdown list 90 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 4 Edit the Alar
68. eneral DDNS Email SNMP More Settings Enable UPnP a Manual HTTP Port d Inactive RTSP Port Inactive Server Port Inactive HTTPS Port Inactive Figure 77 UPnP Settings Menu 76 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 Check the Enable UPnP checkbox 3 Select the Mapped Type There are two types e Auto Automatic mapping port 8000 80 554 443 e Manual Edit the port by clic 4 Click the Apply button to save the settings Configuring More Settings You can configure alarm host and port by selecting the more setting tab as shown in Figure 78 General DDNS Email SNMP NAT Alarm Host Figure 78 More Settings Menu 1 Alarm Host Send the alarm event or exception message to the alarm host when an alarm is triggered The remote alarm host must have the CMS Client Management System Software installed e Enter the IP address of the remote PC on which the CMS Software is installed in e Enter the alarm monitoring port in Alarm Host Port which must be the same as the port configured in the software 2 Port e Server Port Enter the Server Port which designates the port to be used with the client software e HTTP Port Enter the HTTP Port which refers to the one to be used with the built in Web Server e Multicast IP Enter the Multicast IP to enable multicast e RTSP Port Enter the PTSP Port PTSP is a network control protocol designed for use in entertainment and communication systems to c
69. eneric Figure 100 POS configuration 2 Choose the POS channel for parameters setting 3 Click on the Enable check box and configure Device Name Connection and POS Protocol 4 Click Connection to select one connection mode between the Text In device and DVR Note For the communication protocol AVE it only supports RS 232 connection mode Note For the communication protocol Generic it supports all of the 3 connection modes above RS 232 TCP Listen and TCP Receive modes a For the RS 232 connection click Set to configure RS 232 settings as follows Note All the RS 232 settings should be consistent with the POS terminals settings and the RS232 Mode shall be selected as Transparent Channel Note Only 1 POS terminal can be connected via RS232 94 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 3 4 O me ransparent Channel Figure 101 RS232 Setting b For the TCP Listen mode Click Set to enter TCP Listen Settings as follows CP Listen ka RS232 TCP Receive Figure 102 TCP Setting Note The IP Address should be exactly the same as the IP Address of POS terminal For this kind of connection you should use a hub between the POS terminal and DVR Figure 103 TCP listening 95 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual c For the TCP Receive mode Click Set to Network Receive Settings as follows Note The port should be exactly the same as the port of POS term
70. es HDVR NVR User s Manual Configuring Cameras Adding and Removing IP Cameras Depending on the model of your DVR IP cameras can be setup and used in conjunction with regular analog cameras Before configuring IP cameras please ensure the network settings for your DVR is properly setup To manage IP cameras 1 Enter the Cameras menu by going to Menu gt Cameras Setup gt Cameras 2 Select the IP Camera tab as shown in Figure 110 IP Camera Import Export PoE Information 10 13 6 251 192 168 254 4 192 168 254 5 192 168 254 6 192 168 254 7 192 168 254 8 192 168 254 9 192 168 254 BackDoor IPCamera 03 IPCamera 04 IPCamera 05 IPCamera 06 IPCamera 07 IPCamera 08 IPCamera 09 HIK VISION HIK VISION HIK VISION HIKVISION HIK VISION HIKVISION HIKVISION HIKVISION JA MD A Y Y Y Y rPrPPrP Per Pe PO k ie i i i i i A A 192 168 254 IPCamera 10 HIKVISION Figure 110 IP Camera Configuration Menu 3 Click the Refresh button to automatically detect connected IP cameras on the network 4 Check the checkbox of certain detected cameras to add The basic information of the selected camera will display on the left side of the interface 3 If the password of the selected IP camera is default you can click Quick Add to add the camera Otherwise enter the password in the Camera Password box on the left side You can also edit the basic parameters of the selected camera by click 4 before you ad
71. f there is no virtual disk existing under the array the array migration cannot be done If the virtual disk of the array is under initialization the array migration cannot be done Note After RAID migration and capacity expansion the expanded capacity for each virtual disk can be calculated by the following formula Expanded VD capacity Original VD Capacity Original Array Capacity Newly Added Capacity of Hard Disk Upgrading Firmware You can view the information of the firmware and upgrade the firmware by local backup device or remote FTP server 124 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 1 Enter the Firmware interface to check the information of the firmware including the version maximum physical disk quantity maximum array quantity auto rebuild status etc Physical Disk Array Virtual Disk lobal Hot Spare Array Hot Spare zz tj Bo N BO 01510 2 O Figure 146 Firmware Interface 2 You can click the Upgrade button to upgrade the firmware Local upgrade and FTP upgrade are available FIP Upgrade Cancel Figure 147 Upgrade Interface 125 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER10 Disk Management 126 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Managing Disks Checking Disk Status The status of all installed hard disk drives HDD and Network hard drives can be checked under the HDD menu To check the status of installed disks 1
72. f your own individual location OUOBGOJEM Figure 41 Camera Order Settings Menu To set the camera order 45 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 1 Enter the Live View menu shown in Figure 41 by going to Menu gt System Configuration gt Live View Select the View tab Select the Video Output Interface to configure camera order for ai 4 Select the Screen Configuration you would like to use in Live Feed by clicking mili e Le The preview of the screen configuration on the right will change depending on the option selected 5 Click to select a screen in the right region and double click to select a channel in the left region Thus the selected channel will be displayed in the corresponding screen Note xx means no channel will be displayed in this screen 6 Click El to start live view of all channels and click ici to stop live view all channels Click ki OT ei to go to the previous or next page For example in 2x2 screen configuration mode pressing the Next button will bring up the next set of 4 displays 7 Click the gt button to save settings 8 Click to exit out of the menu Channel Zero Encoding Channel Zero Encoding can be chosen to decrease the bandwidth reguirement without affecting the image guality when you need to get a remote view of many channels in real time from web browser or remote client To setup channel zero encoding as following steps Steps 1 Enter the
73. g the permission Ob Usina ea nase a ae tike 80 B Je Cs win TU Era AN Sn Rn nnn oa 81 Editinsta Uria lr ii iii iaa 82 O O a T 82 Contisurna PLACAS iaa 83 Comm curing Basie PIZ Se iS isc 83 Customizing PTZ Presets Patterns and Patrol Sanidad 84 Contretiane Alarms and X E DO Ss cera tec a a da 86 Setin Up Motion Detecta 86 Configure Alarmi puts ise 89 Conti curn Alar OPUS A bei ae nee gave 90 Contour Except dade 91 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Contistirine E mail STINGS cari A iia 92 Connew Hot Spare SENE S code 93 Contisurme POS Pomtot sale OEUNOS ici 94 CHAPTER 8 Camera Management ccccssssssssssssssssssssssssssssccsssssssssssssssssssssssssssssssssssssssssssss 101 Bo AVES vig Va CAMeraS et AE AA A OE AMO TA RE ZATONA 102 Adding and Remo me MC AME TA a Je eb a 102 Adding and Removing Analog Cameras cc sssssesssssseeececceeeeecceeeeaaaasessessseeeeeeceseeeeeeeeeaaaaaaeeeseses 106 IP cameras List import and Ex POTU a io 107 POR li OTA MON AA Nea ni a A de dek date 108 Contisutino Pri yay Mask oia 109 Comino iano Tampere dao 109 Contorno Video O86 sidad 111 Contistirmo OSD SON St an la 111 Conneurne Video Quality DIJO NOSTS peralta zavoj el ba tai 112 CONSUE A Ces ON ic is 113 CHAPTEE R9 RAID Con CUA ION ani E Na A ie 115 Configuring Array and Vi DIS a ie k dai 116 Onneton mC Onora OM a Ne E AE O AI VO O a O asians 116 Manually Creatine Array and Virtual DISK sie sane nee obn
74. ge device and click the Refresh button If the device is detected a list of its file contents as well as the available free space will be shown You may delete files on the USB storage device to free up additional storage space by clicking the Delete button on the selected file You may also format the device by clicking the Format button Formatting will remove ALL files from the device When there is sufficient storage space for backup click the Export button A backup progress bar will be shown Click the OK button once backup has completed Figure 72 Export Finished Message Click the Cancel button to return to the File Management menu 10 You can also click Ouick Export in the Record menu to export all the record files for the selected channel 72 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER7 System Configuration 13 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Network Settings Network settings must be configured before you re able to use your DVR over the network Configuring General Settings To configure network general settings 1 Enter the Network Configuration menu shown in Figure 73 by going to Menu gt System Configuration gt Network 1 Configuration DDNS Ema SNMP NAT More Settings 10M 100M 1000M Setf aday u ic ef 48 4c 45 12 192 168 254 1 Figure 73 Network Settings Menu 2 Select the General tab The current network settings are displayed on
75. gure 14 22 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 14 Soft Keyboard The buttons on the soft keyboard represents Switch to Uppercase Switch to uppercase input Backspace Delete the character in front of the cursor Enter Confirm selection Ea Symbols Number Switch to symbols and numbers input 23 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTERZ Getting Started 24 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Starting and Shutting Down Your DVR Proper startup and shutdown procedures are crucial to expanding the life of your DVR Startup Your DVR e Ensure the power supply is plugged into an electrical outlet It is HIGHLY recommended that an Uninterruptible Power Supply UPS be used in conjunction with the unit The Power indicator LED on the front panel should turn red indicating the unit is receiving power e Connect the DVR to a VGA monitor You will only see the DVR menu system when it s connected to a VGA monitor e Press the POWER switch on the back rear panel The Power indicator LED should turn blue The unit will begin to start e After startup the Power indicator LED will remain blue A launch screen with the status of the HDD will be shown Figure 15 If an X is shown it means that the HDD is not installed or cannot be detected Embedded Net DVR Figure 15 Startup Splash Screen Shutdown Your DVR There are two proper ways to shut
76. h will also make searching for events easier To set up motion detection 1 Enter the Motion Detection menu shown in Figure 88 by going to Menu gt Recording Configuration gt Motion Detection one Setting Figure 88 Motion Detection Settings Menu 2 Select the camera to configure in the camera dropdown list 3 Check the Enable Motion Detection checkbox to enable motion detection for the selected camera Uncheck the checkbox to disable motion detection 4 Set the motion detection sensitivity by adjusting the green Sensitivity bar The more lime green rectangles selected in the bar the higher the sensitivity will be to motion 5 Set the motion detection region in the preview screen on the right side of the menu by left clicking with the mouse on an open area A red grid will be shown designating that the selected area 1s part of the motion detection region Dragging or left clicking on areas that overlap the current selected motion detection area will include them into the region You may also click the Full Screen button to include the whole area into the motion detection region Left clicking on any part of the grid will remove that section from the motion detection region 6 If you re not satisfied with the selected region you may click the Clear button to reset the motion detection area 7 Select the actions to take if motion is detected in the designated regions Click the Set button to pop up the Handing menu 86 D
77. he camera to configure from the camera dropdown list Select the Parameter Type to configure Both Continuous and Event can be configured Select the picture resolution in the Resolution dropdown list The options for the capture resolution include AUTO 4CIF CIF and QCIF Select the picture quality to High Medium of Low in the dropdown list Select the time period in second between two capturing actions If the parameters can be used to other channels click Copy to copy the settings to other channels Click the Apply to save the settings ee gt oe eee Note The interval is the time period between two capturing actions You can configure the parameters from Is to 24 Hour Configuring Capture Schedule Set the capture schedule then the camera will automatically start stop capturing according to the schedule To setup a record schedule Steps 1 Enter the Schedule menu by going to Menu gt Recording Configuration gt Schedule 2 Select the Capture tab as shown in Figure 56 to configure capture schedule 56 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual IF amerad Enable Schedule a a 10 Figure 56 Capture Schedule Configuration Menu 3 Select the camera to configure from the camera dropdown list 4 Check the Enable Schedule checkbox to enable the capture schedule If the checkbox is unchecked the capture schedule will be disabled 5 Edit the capture schedule The setting steps are the same wi
78. he video quality diagnosis menu shown in Figure 124 by going to Menu gt Cameras Setup gt video quality diagnosis 112 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual SA Figure 124 Video Quality Diagnosis Configuration Menu Select the camera to setup Video Quality Diagnosis configuration in using the camera dropdown list Check the Enable Video Quality Diagnosis check box to enable this function Click the Handing button to set the alarming schedule and linkage action Configure Diagnosis Mode settings including Blurred Image the blurredness of image Abnormal Brightness the brightness of the image Color Cast the color cast of image 9 If you want to reset the default settings of threshold click Default to set a default threshold value to each kind of diagnosis mode 10 If the same configurations can be applied to other channels click Copy to copy the settings to other channels 11 Select the Apply button to save these settings and select Ba to return to the previous menu Selecting 5 without clicking Apply will quit out of the menu without saving settings Configuring VCA VCA settings can be enabled on any of the channels on your DVR to detect VCA events If the VCA related events happen this function will alarm to users Note this function can be only enabled by VCA supported cameras To configure VCA settings 1 Enter the Video Loss menu shown in Figure 125 by going to Menu gt Cameras Setup gt
79. ick the Refresh button The contents of the USB storage device will be shown on the screen Select the list file Click the Import button In the pop up window click Yes to confirm the import and the system will automatically reboot to make it effective Click BE to exit out of the Import Export menu 107 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual PoE Information Detailed PoE power consumption information and configuration can be accessed in this tab To access the PoE information 1 Enter the Cameras menu by going to Menu gt Cameras Setup gt Cameras Select the PoE Information tab as shown in Figure 119 a ae eo 3 IP Camera IP Camera Import Export Figure 119 PoE Information interface 2 Choose the corresponding IPC channel and choose the suitable PoE protocol PoE af PoE at and no PoE Click Apply button Click gt to exit out of the PoE Information menu Note This function is only available on specified 7716NI SP model 108 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Privacy Mask Privacy Mask can be setup to mask off sensitive or private areas in the field of view of a camera To configure privacy zones 1 Enter the Privacy Mask menu shown in Figure 120 by going to Menu gt Cameras Setup gt Privacy Mask Figure 120 Privacy Mask Settings Menu 2 Select the camera to setup privacy mask in using the camera dropdown list on the upper left of the menu 3
80. inal you can click and edit it via virtual keyboard The default port number is 10000 TGP Receve Si RS232 TCP Listen Figure 104 TCP Receive mode 5 Click POS Protocol to select one communication protocol between the POS terminal and DVR Note For the communication protocol AVE it only supports RS 232 connection mode Note For the communication protocol Generic it supports RS 232 TCP Listen and TCP Receive connection modes e For the Generic protocol click Set to configure Generic Settings as follows 1 Start Line Identifier You can define the transaction start string The transaction data will starts to display on the video and be recognized as the start of a new transaction every time when the DVR detects this Start Line Identifier string Note Hex stands for Hexadecimal which is a numeral system based on 16 common symbols 0 9 and A F or a f Click Hex check box to enable Hexadecimal mode 96 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual More Setting Filter Figure 105 POS Setting 2 End Line Identifier You can edit the End Line Identifier string when the transaction data should be finished to display on the video Note Hex stands for Hexadecimal which is a numeral system based on 16 common symbols 0 9 and A F or a f Click Hex check box to enable Hexadecimal mode 3 Line Delimiter Click to edit the line delimiter character via virtual keyboard as follows Note Up to 40 chara
81. ing the corresponding icon The affect will be displayed immediately on the screen e Click Default will restore the default settings e If the same settings can be applied in other channels click the Copy button to pop up a Copy to box and check the corresponding checkbox Click the OK button to save and back to Image Setting menu Click Cancel to exit without saving e Click OK to save the settings and return to the Live Feed mode 5 For IP camera only Customize is supported You can adjust the Brightness Contrast Saturation and Hue by dragging the corresponding icon Click the OK button to save the settings and back to the Live Feed mode You can also enter the Image setting menu by going to Menu gt Cameras Setup gt Image as shown in Figure 31 The steps are similar to the live feed icon setting steps If the same settings can be applied in other channels click the Copy button to copy it to other channels 4 You can also adjust the image parameters like Brightness 37 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 31 Image Settings Menu Here we can set advanced image parameters like white balance exposure WDR day night switch digital noise reduction backlight compensation and video adjustment Live View Strategy Settings for live view strategy to adjust the picture settings of a display as follows 1 Select display 2 Click the Live View Strategy icon This will bring up the Live View Strateg
82. irtual disk please refer to Page 116 if you adopt foreground initialization the virtual disk will display in the HDD Information interface after the initialization is complete Record Information Uniniti alized Figure 130 HDD Information Interface 118 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 15 After the virtual disk has been initialized the status will change from Uninitialized to Normal 16 Enter the Physical Disk interface to configure the hot spare disk if you have installed the fourth disk Array Virtual Disk Firmware 931 51GB Normal Functional WDC WD10EVVS 63M5B0 Figure 131 Physical Disk Interface 17 Select the disk and click Baal to enter the Set Hot Spare interface Cancel Figure 132 Set Hot Spare Interface 18 Set the Hot Spare Type of the selected HDD to Global Hot Spare or the specified hot spare for the existing array 12 Global Hot Spare It can be used as the hot spare for any array created in the system 13 Specified Hot Spare e g test It can be used as the hot spare for the specified array only 19 Click OK to finish the settings Note When the auto rebuild function is enabled the hot spare disk will be automatically used for array rebuilding if the virtual disk is in Degraded status Note At least 2 HDDs must be installed for RAID 0 2 HDDs needs to be configured for RAID 1 At least 3 HDDs must be installed for RAID 5 4 6 8 HDDs need to be cofigured for RAID 10
83. isk 1 Enter the Virtual Disk interface by going to Menu gt System Configuration gt RAID gt Virtual Disk 2 Select a virtual disk and click to delete the virtual disk Figure 139 Attention Message 3 Click the Yes button to confirm the virtual disk deletion Note Deleting virtual disk will cause to delete all the data saved in the disk Deleting the Array If all the virtual disks under an array have been deleted then you can delete that array To delete the array 1 Enter the Array interface by going to Menu gt System Configuration gt RAID gt Array 2 Select an array and click to delete the array 3 In pop up attention box click the Yes button to confirm the array deletion 122 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Note Deleting array will cause to delete all the data in the array Migrating and Expanding When the remaining storage space is lower than the actual needs you can take array migration and online expansion to enlarge the capacity of the virtual disk At least one available physical disk should exist for the array migration To migrating and expanding 1 Enter the Physical Disk interface by going to Menu gt System Configuration gt RAID gt Physical Disk to confirm at least one available physical disk has existed for the array migration 2 Select Array tab to enter the Array interface 3 Select the array to be migrated and click E to enter the Migrate Array interface
84. itine Record schedule sina aa le A io cat a a diti a o ie velika 51 Commenting Holiday Seto di eki ei aa el di dic 55 COS NS setings Ior apunt 56 Commeuring Caprure Quality Seu es sists NE lanes otc te sie Oled eS 56 Conti 5 Capture SCC CUS viscose ee ias 56 CHAPTERS Play Dah usa an ai a dini od ea reji ah 38 a Ala TAC he ICC AA AE NE AE ST VINO 39 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Understandine the Playback Interfase ali 59 SSA UCM POR Ie CCOLCC lla O ME A NA RESEN 60 Playine Back Recorded PES a ke le ei ele a bela kA 60 Playine Back Multiple Chania A Ne ab nea been 61 TATE s AC eco eaten A ON NA O E NOT anaen 62 SS UALS Fi IR O O O enn oe 63 PAYA Back PICe Seca Se ea eb a ee A acts dn ea ee Gasman ke ee 63 Play ime Back Tas ee sedans Se be obed ei baje kable ea be nies 64 Playin Back POS venis dek an es do a ad austen en de ee ee 66 CHAPTE RO Dick ee a ei aii 68 Ba RIS VII OM NA A EN ob ia Ee 69 Neka ae Vido Blo a O EI EEA A EEA EI AE EEA A TAN 69 Backmenp Video Cipsa ia 70 Backimo AAA II ba ai T2 CHAPTER 7 System Commo ur atom ansam AA ASA AAA AAA 73 ConusuriniS NetWork UINO S a A S A A A bb aiden tes 74 Comm curio General Seti 8 i a A ae A eb be ele aleli 74 rime DDNS esas cao a aos 75 Coni A A 76 Cont tn Urticaria ita 76 Contisutino More SEUNS S ereid a TI Manas me User ACO OU Sana aa ee A a A Ed ajo Peer a ak ene 78 Chance PassWord silos 78 Adding a New Remote Local Use resin a 79 Changin
85. k drive HDD must be first formatted before it can be used with your DVR Formatting the disk will erase all data on it To format a new disk 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Select a disk to format If the disk is one that is newly installed the status of the drive will show up as Uninitialized 3 Click the Init button 4 A confirmation message similar to the one shown in Figure 150 will appear on the screen Click OK to continue formatting process Cancel Figure 150 Disk Format Confirmation 5 A format progress bar will be shown on the menu After the disk has been formatted the status of the disk will change to Normal Record Information Storage Mode Figure 151 Disk Format Progress Bar Enabling HDD Overwrite Enabling HDD overwrite will allow the DVR to overwrite the installed disks once the disks are full To enable HDD overwrite 1 Enter the HDD menu by going to Menu gt System Configuration gt HDD 2 Select the Record Information tab as shown in Figure 152 HDD Information Storage Mode Disk Clone HDD v OSATA1 Record Capture Figure 152 Record Information Menu 3 Check the Overwrite checkbox 129 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 4 Click the Apply button 3 Click to exit Enabling HDD Sleeping mode Enabling HDD sleeping mode will allow the HDD enter low power cost work mode when no recording work is detected To enabl
86. l screen playback mode there is no POS data overlay function please switch to full screen playback mode to get the POS overlay function which is enabled by default 66 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual In full screen mode if you want to hide the POS information click on the T button to disable the overlay function as shown below 67 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER6 Backup 68 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Backing up Video Clips Video clips can be backed up to various devices such as USB flash drives USB HDDs or a DVD writer Selecting Video Clips Video clips can be selected for backup in the Playback Interface using the controls found in the Mark Clip For Export panel shown in Figure 67 Mark Clip For Export Figure 67 Mark Clip For Export Controls The controls found in the Mark Clip For Export panel include e Start Stop Button Mark the starting ending point for the video clip When you click the Start it will turn to the Stop button e Play Button Play the selected video clip e Save Button Save the selected video clip to the HDD e Clear Button Clear the selected video clip To select video clips in the Playback Interface 1 Enter the Playback Interface shown in Figure 68 by going to Menu gt Playback gt Record a m P Camera Y 09 23 29 6 Figure 68 Playback Menu 2 Search for the recorded files that you woul
87. lect the Arming Schedule tab to set the arming schedule Up to 8 periods can be configured If the same schedule can be applied in other days click Copy 2 Select the Handing tab to set the actions to take if tamper proof is detected 3 Click Apply to save the settings Click OK to back to the previous menu 7 Ifthe same settings can be applied in other channels click Copy to copy the same configuration to other channels 8 Click Apply to save the settings na o gt 110 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Video Loss Video loss detection can be enabled on any of the channels on your DVR to detect the loss of video To configure video loss detection 1 Enter the Video Loss menu shown in Figure 122 by going to Menu gt Cameras Setup gt Video Loss Figure 122 Video Loss Detection Menu Select the camera to setup video loss detection in using the camera dropdown list Click Enable Video Loss Detection Press the Handing Set button to set up handing method 1 Select the Arming Schedule tab to set the arming schedule Up to 8 periods can be configured If the same schedule can be applied in other channel click Copy 2 Select the Handing tab to set the actions to take if video loss is detected 5 Click the Apply button to save the settings Click OK to back to the previous menu 6 If the same settings can be applied in other channels click Copy to copy the same configuration to other channels
88. like to configure your own settings enter the settings for e IP Address IP address you would like to use for your DVR e Subnet Mask Subnet Mask of network e Default Gateway IP address of your Gateway Typically the IP address of your router e DNS Server The preferred and alternate Domain Name System DNS Server to be used with your DVR Click the Apply button to save the settings Configuring DDNS Dynamic DNS allows you to create a hostname and associate it to your IP address making access to your DVR over the internet easier To configure DDNS L Select the DDNS tab to enter the DDNS settings interface as shown in Figure 75 General Email SNMP NAT More Settings Enable DDNS ti DDNS vw www hik online com o Figure 75 DDNS Settings Menu Check the Enable DDNS checkbox Select a DDNS type from the DDNS Type selection box Five different DDNS types are selectable IPServer DynDNS PeanetHull NO IP hkDDNS e IPServer Enter Server Address for IPServer e DynDNS 1 Enter Server Address for DynDNS 2 Enter the domain obtained from the DynDNS website in the Domain Name textbox 3 Enter the User Name and Password registered in the DynDNS website e PeanutHull Enter the User Name and Password obtained from the PeanutHull website e NO IP 75 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 1 Enter Server Address for NO IP 2 Enter the domain obtained from the DynDNS website www no ip co
89. login with Administrator accounts Deleting a User To delete a user from the DVR 1 Enter the User menu shown in Figure 79 by going to Menu gt System Configuration gt User 2 Select a user and click to delete 3 Click the Yes button to confirm the deletion of user or click the No button to cancel 81 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Editing a User To edit a user 1 Enter the User menu shown in Figure 79 by going to Menu gt System Configuration gt User 2 Select a user and click to edit user 3 Edit user information including user name password level and MAC address 4 Click the OK button to save and exit Note User password can be both numbers and characters You can click the button cl on the password editable fields to enter characters Switch User On the main menu see in Figure 84 information about users are show on the lower left Playback File Management Recording Conhguration Cameras Setup System Configuration Maindariarmme System infomation User admin Figure 84 Main Menu 82 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring PTZ Cameras Configuring Basic PTZ Settings Settings for a PIZ camera must be configured before it can be used Before proceeding verify that the PTZ and RS 485 of the DVR are connected properly To configure PTZ settings 1 Enter the PTZ menu shown in Figure 85 by going to Main Menu gt Cameras Setup gt
90. lude in the search Analog cameras are listed on the first row preceded with the letter A If you would like include all analog cameras in the search check the Analog checkbox IP cameras are listed on the second row preceded with the letter D If you would like include all IP cameras in the search check the IP Camera checkbox Select the start time and the end time Click the Search button A list of results with your search criteria will be shown at a pop up box You can set the Pre play and Post play time Select one result to see the details by clicking Details button or quick export by clicking the Quick Export button If you select type Alarm Input First you select one alarm input channel or you can check the Alarm Input No box to select all channels Select the start time and the end time Click the Search button A list of results with your search criteria will be shown at a pop up box and you can select record to do proper settings Searching for Captured Picture Search and view captured pictures stored in HDD To search for all captured pictures Enter the File Management menu by going to Menu gt File Management gt Picture Select channel picture type Select start time and stop time Click Search button to enter Search Result interface Left click to view the picture ma cia ale a pa E mDi 2 2014 05 14 14 58 13 odeji 2 2014 05 14 14 58 17 Figure 164 Picture Search 138 DS 7700NI SP 9000
91. m Figure 158 Local HDD Settings 3 Select the Clone Source by checking the box 4 Select the Clone Destination by choosing the eSATA devices and set the Usage of devices as Export 5 Click Clone button to launch the clone process Note The storage volume of clone source and clone destination should be identical otherwise the clone cannot be executed 133 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual HDD Detect The device provides the HDD detection function such as the adopting of the S M A R T and the Bad Sector Detection technique S M A R T The S M A R T Self Monitoring Analysis and Reporting Technology is a monitoring system for HDD to detect and report on various indicators of reliability in the hopes of anticipation failures Bad Sector Detection B ee unchonal S MART Information 0x1 Raw Read Error Rate 0x3 Spin Up Time 0x4 Start Stop Count 0x5 Reallocated Sector Count Ox Seek Error Rate 0x9 Power on Hours Count Oxa Spin Up Retry Count Figure 159 S M A R T Settings Interface To viewing S M A R T information na a gt Note Enter the S M A R T Settings menu by going to Menu gt System Maintenance gt HDD Detect Select the S M A R T Settings tab as shown in Figure 159 Select a HDD to view its S M A R T information list You can choose the Self test Type from the dropdown list including Short Test Expanded Test and Conveyance Test Click the Test butt
92. m in the Domain Name textbox 3 Enter the User Name and Password registered in the NO IP website e HiDDNS 1 The Server Address defaults to www hik online com 2 Enter the Device Domain Name The domain name can only contain the lower case letter numeric and and it must start with the lower case letter and cannot end with 3 If you have more than one device you can register an account on www hik online com to do some management 4 Click the Apply button to save the settings Configuring SNMP You can use SNMP protocol to get device status and parameters related information To configure SNMP 1 Select the SNMP tab to enter the SNMP settings interface as shown in Figure 76 General DDNS Email NAT More Settings Enable SNMP Figure 76 SNMP Settings Menu Check the Enable SNMP checkbox Enter the IP address of SNMP host in the Trap Address textbox Enter the port of SNMP host in the Trap Port textbox Click the Apply button to save the settings ua Mb Sai Configuring UPnP Universal Plug and Play UPnP can permits the device seamlessly discover the presence of other network devices on the network and establish functional network services for data sharing communications etc You can use the UPnP function to enable the fast connection of the device to the WAN via a router without port mapping To configure UPnP 1 Select the UPnP tab to enter the UPnP settings interface as shown in Figure 77 G
93. m Name Select the Dwell Time 6 Setup arming schedule for the alarm output by click Handing Set Choose one day in a week and set an arming schedule If the schedule can also be applied to other days click Copy Click Apply to save the settings and back to the Alarm Output interface If the same setting can also be applied to other alarm output click Copy Click Apply to save the settings You can check the alarm output status in the Alarm Output Status list in the Alarm Output interface di oe ae Configuring Exceptions Actions can also be triggered when the DVR detects certain exceptions To setup exception configuration 5 Enter the Exception menu shown in Figure 97 by going to Menu gt System Configuration gt Exception Enable Event Hint Y Exception Type DD Full v Figure 97 Exception Configuration Menu 6 Select the Exception Type to configure The exception types include HDD Full If selected trigger action when HDD 1s full HDD Error If selected trigger action when errors on the HDD are detected Network Disconnected If selected trigger action when a network disconnected is detected IP Conflicted If selected trigger action if an IP conflicted is detected Illegal Login If selected trigger action when illegal logins are detected Video Signal Exception if selected trigger action when video signal is abnormal Input Output Video Standard Mismatch If selected trigger action when video output standa
94. n blue and there is still no response from the remote please check the following 1 Batteries are installed correctly and the polarities of the batteries are not reversed 2 Batteries are fresh and not out of charge 3 IR receiver is not obstructed 4 No fluorescent lamp is used nearby Using a USB Mouse A regular 3 button Left Right Scroll wheel USB mouse can also be used with this DVR To use a USB mouse 1 Plug USB mouse into one of the USB ports on the front panel of the DVR 2 The mouse should automatically be detected If in a rare case that the mouse is not detected please refer to the recommended device list from your provider The buttons on the mouse corresponds to 1 Left Button 8 Single Click Select a component of a menu such as a button or an input field This is similar to pressing the ENTER button on the remote front panel controls 9 Double Click Switch between single screen and multi screen mode in Preview Playback mode 10 Click and Drag Clicking and dragging the Left mouse button can be used to control the pan tilt of a PTZ camera as well as to vary the position of digital zoom area and camera OSD It can also be used to set the alarm areas 2 Right Button 11 Single Click Shows pop up menu in preview interface Exit to return to the previous menu Using the Soft Keyboard When a mouse is used to perform task on the DVR clicking on a text input field will bring up the Soft Keyboard shown in Fi
95. nd Patrols Your DVR allows you to customize presets patterns and patrols for a connected PIZ camera A PIZ camera must first be configured before PTZ presets patterns and patrols can be customized See Configuring Basic PTZ Settings To customize PTZ presets 1 Enter the PTZ menu by going to Menu gt Cameras Setup gt PTZ 2 Select the More Settings tab as shown in Figure 87 3 Select Save Preset and move the camera to the desired position using the PTZ control buttons 4 Double click on a preset number The current position of the PTZ camera will be set for the selected preset number 84 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 5 To test the newly configured preset first move the PTZ camera to a different position Select Recall Preset and click on the preset number The camera should move to the location that was set for the selected preset number 6 Repeat the steps to save more presets Note Only the first 17 presets are shown in the table To save or recall more presets click on the button Clicking the button will bring up a selection box for presets up to 255 To customize PTZ patterns 1 2 de 4 de Enter the PTZ menu by going to Menu gt Cameras Setup gt PTZ Select the More Settings tab as shown in Figure 87 Select a Pattern Number to set from the dropdown list 4 Click to begin recording the movement of the PTZ Move the PTZ to the desired locations using the PTZ
96. nd under Playback Controls include Play Forward Button Button to playback recording Play Reverse Button Button to playback recording in reverse Speed Down Button Button to decrease play speed Speed Up Button Button to increase play speed Mute Button Button to enable and disable audio in playback mode Add Default Tag Button to add default tag Add Customized Tag Button to add customized tag and input tag name Edit Tag Button to check edit and delete tag s Enter Exit Full Screen Mode Button to enter into and out of full screen mode 60 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual To playback recorded files 1 2 3 gt 10 Search and select recording to play back in the Playback Interface Click the Play Forward button to begin playback of selected recording and the Pause button to pause playback You may slow down or speed up the playback speed by clicking the Speed Down Speed Up button You can click to zoom in zoom out the timeline and select the exactly time Click the Full Screen button to enter full screen playback mode shown in Figure 59 Camera 11 Camera 1 Camera 13 Camera 14 Camera 15 A Caren 16 C rmora 01 iPCarmera 02 MA iPCamera 03 B iPCamera 04 MA iPCamera 05 Camera 06 iPCamera 07 2017 17 10 17 54 16 2092 17 20 164703 Figure 59 Full Screen Playback Mode Clicking El will return to the original playback mode Click the Mute
97. ngs interface and Virtual Disk interface to view the rebuilding status 6 After rebuilding successfully the array and virtual disk will restore to Functional ma Note At least one available physical disk should exist for rebuilding the array Note It is recommended to enable the Auto rebuild function and set the hot spare disk for automatically rebuilding the array Repairing Virtual Disk When the disk cannot display in the HDD Information interface while the virtual disk can still show in the Array Settings interface you have to repair the virtual disk Note If the virtual disk is under foreground initialization the repairing cannot be done To repairing virtual disk 121 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 1 Enter the Virtual Disk interface by going to Menu gt System Configuration gt RAID gt Virtual Disk Physical Disk Array Firmware 100G test Degraded RAID 5 4 100G test Degraded RAID 5 4 Figure 137 Virtual Disk Interface 2 Click M to repair the virtual disk 3 After successfully repairing the following attention box will pop up Click OK to finish the settings Figure 138 Repair Attention Message 4 You can see the disk again in the HDD Information interface Deleting Array Vitual Disk You can delete the array and virtual disk Before deleting the array the virtual disk s under this array must be deleted first Deleting the Virtual Disk To delete the virtual d
98. nt of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteries according to the instructions provided by the battery manufacturer DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CONTENTS GHATTER E hitr OCU COM A 8 DE O act cece ee eee cere eee ace A O nena nace A OI OTA O a a a 9 PROGUC ECACC Stane A Ade AA eo Ne zo slede bella jaih 9 RA na Ai hoes oa as ee na A as asses wad sated esate gn Saeed ed ee 12 Produ i Application Diaria a 15 Opera sa ee A a ia as eo es ei lod 17 Usina the Front Panel Ont ONS a id 17 Usmo a USB MOUS an aa ai 22 Sime LNG SOVRE DO Css aa aaa A ad a A obna S 22 CHAPTER Getting Started AA A AAA AA 24 Starina and SU Down Your DV Ra alada 25 SA AA AAA a o N 25 Shutdown Y OUT DVR ica 25 o e in VOU DATE a a A EO VA 26 oje KBT 0 DN ie O O TNO 26 Sie HALE Rca Date TIME an arenes a ES v Checkine the Status Of Your DVR ana ae A Da bs 28 CMA PoE ECR 3 Dive FeO ia uni kao aaa aa a Rione EASRA 32 Aate abba oars oe se A EN ARA NE aa A ANE ME NEUE TANINI 33 Understandine Live Pecados id 33 Operating the LIVE Perdi lis 34 Usine Dis play MENU sia ita iaa 40 Comme urine ive Feed DIS Pla VS nn a a NE ae ooo bebe Ra eh sobe bote bate zobi ete lela 43 a A NE A AN RE ee ai i IE an ore ten EM NICI TSENAH 45 Channel Zero Encoder 46 CHAPTER A Record Settings cuina 48 Contisttine Settings TOR RECO iii iii 49 COMP ounn Recordin SENES dios celda 49 Contisu
99. nu gt Playback gt Smart Figure 60 Smart Playback Interface 62 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Channel Motion Analysis Full Screen Onde Calendar 39 23 Preview Clip Backup Tools Playback Controls Y 4 1 ki Mae ent am to zanke nn aa kremne tes Controls Figure 61 Smart Playback Menu Smart search In order to locate motion detection event easily and accurately in the playback progress line the users are allowed to analyze a certain area scene dynamically and to get all of the related motion detection events that occurred in this area Note The smart search function is only available for analog channels To use this function 1 Enter the playback interface and play the video 2 Move your mouse into the video window and drag an area for motion detection analysis The button EI is used for clearing all the area and the button CI is used for choosing the full screen area 3 After selecting the area click a to search you will get the motion detection events easily from the long time line Time line turns to red when motion detection events happen 4 You can get the scene you need conveniently by moving the green vertical line or you can click and to move between the neighbor events 3 You can also do the smart search in Full Screen mode as shown in Figure 59 by clicking a to pop up the tool bar asi a Playing Back Pictures Search and view captured pictu
100. ogs Many events of your DVR are logged into the system logs To access the system logs and search for these events 1 Enter the System Logs menu shown in Figure 173 by going to Menu gt Maintenance gt System Logs 2013 10 22 opo ooo0 JO 2013 10 22 8p35959 v Figure 173 System Logs Menu 2 Select the Start Time and the End Time 3 Select the Major Type from the dropdown list Four major types are available Alarm Exception Operation and Information You can also select All 4 Select the Minor Type under the Major Type to efficiently find the logs 3 Click the Search button The search results will be displayed in a list Figure 174 Click baile to page up and down Note Up to 2000 log files can be displayed each time 149 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2013 10 22 0 00 00 TESTA gt ZEN O CS 5 S Alarm Output E Start Motion Detection MI Chan Makan Dada ski mm 1 Operation 2013 10 22 090052 Local Operation Init information 2013 10 22 0900 53 Start Recording 3 information 2013 10 22 09 00 53 Start Recording 4 information 2013 10 22 09 00 53 Start Recording information 2013 10 22 09 00 53 Start Recording information 2013 10 22 0900 53 Start Recording information 2013 10 22 09 00 53 Start Recording information 2013 10 22 09 00 53 Start Recording information 2013 10 22 09 00 53 Start Recording 9 information 2013 10 22 09 00 53 Start Recording inform
101. on to start the S M A R T HDD self evaluation If you want to use the HDD even when the S M A R T checking is failed you can check the checkbox of the Continue to use this disk when self evaluation is failed item Bad Sector Detection 1 Enter the Bad Sector Detection menu by going to Menu gt System Maintenance gt HDD Detect 2 Select the Bad Sector Detection tab as shown in Figure 160 134 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual SMART Settings HDD No 5 ss Kay Area Detection gt 931 51GB 232MB ss ot tested Do Figure 160 Bad Sector Detection Interface Select the HDD you want to configure in the dropdown list Choose Key Area Detection or All Detection Click the Detect button to start the detection Click the Pause Cancel button to pause cancel at any time you want If the HDD 1s normal you can see the green color icon on the screen while red means damaged and yellow means shield Click the Error Info to see the detail damage or shield information IAM Rw ag 135 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Managing Files Searching for Recorded Files Previously recorded files can be searched by criteria in the File Management menu To search for all recorded files 1 Enter the File Management menu shown in Figure 161 by going to Menu gt File Management gt Record Include Cameras A Start End time of record 2014 02 21 16 06 16 2014 05 13 09 23 45 L
102. ontrol streaming media servers e HTTPS Port Check the Enable HTTPS checkbox and enter the HTTPS Port HTTPS is used for secure communication over network 3 More e Enable High speed Download Check the Enable High speed Download checkbox High speed Download is used to enhance the speed of network download but it may cause local GUI operation stucked 77 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual e Enable Telnet Check the Enable Telnet checkbox Telnet is used mainly for system maintenance and debugging 4 Click Apply to save the network settings and click Bey to return to the previous menu Click without clicking Apply will quit out of the menu without saving settings Managing User Accounts By default your DVR comes with one user account the Administrator account The Administrator user name is admin and the password is 12345 The default password for Administrator should be changed right away for security reasons The Administrator has the authority to add delete or configure parameters for many of the system functions Changing Password You can change the default password by going to Menu gt System Configuration gt User as shown in Figure 79 m System Configuration 00 00 00 00 00 00 Figure 79 User Settings Menu To change the password 1 Click to pop up the Edit User menu as shown in Figure 80 78 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Na 6 00 00 00 0
103. oth audio video composite stream and video stream audio and video synchronization during composite stream encoding Support watermark Local Monitoring Simultaneous HDMI VGA and CVBS outputs O HDMI output and VGA output at up to 1920 1080P resolution 1 4 6 8 9 16 division live view 1s supported and the display sequence of screens is adjustable Live view screen can be switched in group and manual switch and automatic cycle live view is also provided the interval of automatic cycle can be adjusted The selected live view channel can be shielded Motion detection tamper proof video exception alert and video loss alert functions Manual video quality detection and handling Privacy mask Several PTZ protocols supported PTZ preset patrol and pattern Zooming in by clicking the mouse and PTZ tracing by dragging mouse HDD Management Up to 16 disks 8 SATA hard disks and 8 network disks and 1 eSATA disk can be connected Each SATA hard disks and network disks with a maximum of 4TB storage capacity and eSATA with less than 2TB capacity Support eSATA disk for recording or backup HDD group management HDD quota management different capacity can be assigned to different channel Support S M A R T and bad sector detection Recording Capture and playback Holiday recording schedule configuration Continues and event video encoding parameters 8 recording periods with separated recording types configurable Pre
104. ow rectangle 1s the overlay zone Ingger Channel Handling PIZ Linking Figure 36 Overlay Zone Using Display Menu The Display Menu can be accessed by right clicking the mouse on any of the display in Live Feed mode The Display Menu as shown in Figure 37 allows you to quickly change into different display modes and to start stop auto switching of the display modes 40 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Menu Single Screen Multi screen Previous Screen Next Screen Start Auto switch Start Recording Add IP Camera Output Mode POS Events Menu Click to go to DVR Main Menu If the system is locked you must enter the current Admin password to exit out of the Live Feed Menu Single Screen Multi screen Prewious Screen Next Screen Start Auto switch Start Recording Add IP Camera Output Mode POS Events 1344 BackDoor IPCamera 03 IPCamera 04 IPCamera 05 IPCamera 06 IPCamera 07 IPCamera 08 IPCamera 09 IPCamera 10 IPCamera 11 IPCamera 12 IPCamera 13 IPCamera 14 IPCamera 15 IPCamera 16 Single Screen Multi Screen Click to switch the display mode Previous Screen Next Screen Start Auto switch Start Recording Add IP Camera Output Mode POS Events 41 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Previous Screen gt Next Screen Previous Screen Next Screen Click to view the previous next set of display In a 2x2 mode this will show the
105. r The speed of the PTZ movement KA tien onoff Wiper On Off 35 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CI 3D Zoom El Image Centralization a Menu 4 Click the Close icon to return to the Live Feed mode Note PTZ parameters for the camera must be set correctly before the PTZ can be controlled Digital Zoom Mode Enable digital zoom on the selected channel Once enabled the regular feed will be shown in the lower right corner while the zoomed in view will be shown on the full screen The zoomed in region may be changed by moving the red rectangle in the regular feed window as shown in the Figure 28 Right click to back to the Live Feed mode Pa er pa z ma on A Aw Figure 28 Digital Zoom z a Image Settings Set the image mode and image parameters like brightness contrast saturation hue and so on for selected display To adjust the image settings of a display as following steps Steps 1 Select display 2 Click the Image Settings icon This will bring up the Image Settings menu analog camera is shown in Figure 29 IP camera is shown in Figure 30 36 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 30 IP camera Image Settings Menu 3 For analog camera there are four preset modes for selection Standard Indoor Dim Light and Outdoor You can select one according to the real situation e Contrast ll Saturation lal A Sharpness M and Denoising E by dragg
106. r triggered from motion or alarm Manual Record Icon Enable disable manual record Instant Playback Icon Instant playback the record in last five minutes CM 4 Audio On Audio Off Icon Enable disable audio for selected display Capture Icon Capture images for the selected display PTZ Control Icon Enable PTZ control mode for the selected display Digital Zoom Icon Zoom in the selected area to the full screen Ci Image Settings Icon Enter the image setting menu for selected display Live View Strategy Icon Set strategy for selected display including Real time Balanced and Eluency Text Hide Hide the POS information on screen display Close Icon Exit out of current setting and return to previous mode Note Status for video loss is only valid with analog cameras Event icons will only be displayed when armed except for the video loss alarm Note Live View Strategy setting 1s only valid with IP cameras 33 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Operating the Live Feed In Live Feed mode you may adjust the settings for individual cameras by left clicking on the desired display with the mouse The selected display will be surrounded with a green border as shown in Figure 25 MC ie Mk Figure 25 Live Feed Mode The settings you may adjust with each display include Manual Record Enable disable manual record by clicking the icon for a selected display Instant Playback Click the Instan
107. r turns red when a sensor alarm is detected Ready Ready indicator turns blue when DVR is functioning properly Status Status indicator turns blue when DVR is controlled by an IR remote Indicator turns red when controlled by a keyboard and purple when IR remote and keyboard is used at the same time HDD HDD indicator blinks red when data is being read from or written to HDD Modem Reserved TX RX TX RX indictor blinks blue when network connection is functioning properly Guard Guard indicator turns blue when the device is armed off when the device is unarmed The arm disarm state can be initiated by pressing and holding on the ESC button for more than 3 seconds in Preview mode 17 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 2 IR Receiver Your DVR may also be controlled with the included IR remote control shown in Figure 13 Batteries 2X AAA must be installed before operation 3 Front Panel Lock You can lock or unlock the panel by the key DVD ROM Slot for DVR ROM 5 Alphanumeric Buttons Alphanumeric buttons used in various menus of the DVR Some uses include gt e Switching to the corresponding channel in Preview or PTZ Control mode e Inputting numbers and characters in Edit mode e Switching between different channels in Playback mode 6 USB Ports Connects USB mouse or USE flash memory devices 7 Control Buttons e ESC Button The ESC button is used to escape to the previous menu and to arm dis
108. rate type include Variable and Constant Select the recording Frame Rate to use for the designated camera A rate of 30 Full Frame all the way down to 1 16 of a frame can be selected 49 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 1 8 9 10 11 12 Set the video quality using the Video Quality slider Increasing the video quality will also increase the max bit rate recommended The max bit rate can be adjusted according to this recommend Select the max bit rate mode in the Max Bitrate Mode dropdown menu The options for the camera max bit rate mode include General and Customize 32 8192kbps Check the checkbox of record audio to enable or disable audio while recording Select the Video Stream to choose different kind of stream as recording stream The options for the video stream include main stream and substream Click the Apply button to save the settings Click the Copy button to copy the settings to other channels if the same settings can also be used for other channels 3 Select Substream tab as shown in Figure 45 to configure the parameters of sub stream The steps are the same as main stream configuration Main Stream Record Capture a a smi Lele zamera Anal Video amp Audio 176 120 0CIF na sna Figure 45 Substream Settings Menu 4 Select Record tab as shown in Figure 46 to configure some parameters of recording 1 2 3 4 Main Stream S
109. rd does not match 91 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual e Record Capture Exception If selected trigger action when record capture exception is detected e Hot Spare Exception If selected trigger action when Hot Spare Exception is detected e All if selected trigger action when any one of exception above is detected 7 Select the Actions to take when the exception is detected More than one action can be selected The actions available includes e Audible Warning DVR will sound an audio warning if exception is detected e Notify Surveillance Center DVR will notify surveillance center if exception is detected e Send Email DVR will send an email out to the designated recipients if exception is detected e Trigger Alarm Output DVR will trigger alarm output if exception is detected Selecting this option will enable the Alarm Output list where the output to trigger can be selected 8 Select the Apply button to save the exception settings and select to return to the previous menu Selecting pev without clicking Apply will quit out of the menu without saving settings Configuring E mail Settings If you would like to have the DVR send out e mails when certain events are detected or exceptions have been triggered you must first setup the e mail settings To setup e mail settings 1 Enter the Email Configuration menu by going to Menu gt System Configuration gt Network 2 Select the Email tab as shown
110. rding Setting up a record schedule will allow you to further conserve disk space by recording only during the time periods you would like to record at Note In this chapter we take the record schedule procedure as an example and the same procedure can be applied to configure capture schedule To setting the capture schedule choose the Capture tab in the Schedule interface To setup a record schedule 1 Enter the Schedule menu shown in Figure 47 by going to Menu gt Recording Configuration gt Schedule 2 Select the Record tab to configure record schedule P Camera 1 00 00 00 00 o Figure 47 Record Schedule Configuration Menu 3 Select the camera to configure from the camera dropdown list 51 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 4 Check the Enable Schedule checkbox to enable the record schedule If the checkbox is unchecked the record schedule will be disabled Edit the record schedule There are three ways to set the record schedule 5 1 2 3 4 5 6 1 Instant edit On the Record menu select a day from Monday to Sunday to configure schedule for Setup time periods for schedule If the 24HR checkbox is checked recording will occur over the entire day To setup multiple time periods uncheck 24HR and enter the Start End Time for the selected day The start End time are listed using a 24 hr cycle 1 e 18 00 is equivalent to 6 00pm Up to 8 discontinuous periods can
111. re 3 Double click on selected event bar detailed POS transaction information will show in a pop up window as shown below POS Information 2014 01 16 09 38 06 2014 01 16 09 38 38 With us it s personal Store 05603 UP TO 30 DAYS REFUNDS EXCHANGES 2797 S DIAMOND BAR BLYD OIAMONO BAR CA 91 65 909 595 0912 Register 7 Transaction 648226 Cashier 8888 11 30 13 7 45PM PA GLUCOSAMINE 500MG 60CT 2 110 99 GOCACOLA COLA 400ML 20 114 99 DEFU CHOCOLATE 500G 12PC 1000 1199 00 HAAGEN DAZE 200MG 1TC 1000 9120 00 Figure 168 POS Information 142 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Locking and Unlocking Recorded Files To lock and unlock recorded files 1 Search for recorded files using the File Management menu 2 Select the file you would like to lock unlock 3 Click the Lock icon for the selected file Note Locked files will never be overwritten until they are unlocked 143 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER11 DVR Management 144 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Managing System Upgrading the System Firmware The system firmware for your DVR can be updated from a USB storage device or FTP To update the system firmware from a USB storage device 1 Enter the Upgrade menu by going to Menu gt Maintenance gt Upgrade 2 Select the Local Upgrade tab as shown in Figure 169 Figure 169 Local Upgrade Menu Connect th
112. record and post record for alarm motion detection for recording and pre record time for schedule Searching record files and captured pictures by events alarm input motion detection Customization tags searching and playing back by tags Locking and unlocking record files Searching and playing back record files by channel number recording type start time end time etc Smart search for the motion event when playing back Zooming in when playback Reverse playback for multi channel Supports pause speed up speed down skip forward and skip backward when playback locating by dragging the mouse 10 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual O Up to 16 ch synchronous playback O Smart playback feature O Continuous capture of video images and playback of captured pictures O Support select main stream sub stream or transcoded stream as recording stream transcoded stream only for NVR Backup O Export video data by USB or eSATA device O Export video clips when playback O Management and maintenance of backup devices O Automatic backup by eSATA devices O Disk clone by eSATA devices Alarm and Exception O Alarm for Video loss Motion detection Tampering HDD Full HDD Error Network Disconnected IP Conflicted Illegal Login Video Signal Exception Input Output Video Standard Mismatch Recording Capture Exception etc O Alarm triggers full screen monitoring audible warming notifying surveillan
113. res stored in HDD To playing back pictures 2 Enter the Picture interface shown in Figure 62 by going to Menu gt Playback gt Picture 63 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual z dana A boosts Epoo 6 Prost pasa lj Preview Figure 62 Picture Playback Interface Select channel on Channel the dropdown list Select picture type for Continues Event Capture or All Select the start time and stop time Click the search button and the pictures found will be listed in Result interface Click the iga you want to view and it will be display on the preview interface Click Click El to play back the pictures in Full Screen mode as shown in Figure 63 to choose the previous next picture Figure 63 Picture Playback Playing Back Tags 1 Enter the Tag interface shown in Figure 64 by going to Menu gt Playback gt Tag 64 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual nea ed a ae 2014 05 13 00 00 00 5 EN Y ZEN Figure 64 Tag Playback Interface Select channel on the Channel dropdown list Select tag type for Tag Keyword or All If tag type was Keyword Keyword area was editable to allow user to set keywords for fast searching Select start time and end time Select the pre play and post play time Click the Search button and the tag recording found will be listed in Result interface Click g or double click the tag you want to play and it will be display in the
114. t playback icon to show the record in last five minutes If no record is found it means there is no record during the last five minutes Audio Enable disable audio for a selected display To enable disable audio 1 Select one display to enable disable audio 2 Enable audio by clicking the Enable Audio icon and disable audio by clicking the Disable Audio icon An error message similar to the one shown in Figure 26 will pop up if the Enable Audio option is not selected in the Live View menu for the specified channel Figure 26 Enable Audio Attention Message Capture Do capture by clicking the icon for a selected display 34 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual PTZ Control If the selected camera is a PTZ camera you may control it directly from the display Control a PTZ camera as following steps Steps 1 Select the display that corresponds to a PTZ camera 2 Click the PTZ Control icon This will bring up additional PTZ control buttons as shown in Figure 27 A oF Preset PR Figure 27 PTZ Control Mode 3 Control the PTZ by using PTZ control buttons Pan and tilt PTZ by clicking on the directional buttons Zoom in and out using the Zoom In Out buttons and recall presets patrols and patterns by clicking the corresponding icons Below is the description of the PTZ control icons gt Direction buttons and the auto cycle button Zoom Zoom acia Focus Focus manam Iris Tris ra dorar a
115. ted When you check the Trigger Alarm Output checkbox there will display a choose box to select Alarm Output No as shown in Figure 92 Tigger Channel Arming Schedule o a 8 Local Local Local Local E Di gt 1 172 6 23 100 Figure 92 Trigger Alarm Output Settings Menu 8 Select the Apply button to save the motion detection settings and select OK to return to the previous menu Selecting the Cancel button without clicking Apply or OK will quit out of the menu without saving settings 88 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Alarm Inputs Certain actions can also be performed if an alarm input is triggered To setup trigger actions 1 dam gt m Enter the Trigger menu shown in Figure 93 by going to Menu gt Recording Configuration gt Trigger Alarm Input Status i i na A Ac Az Ac As Ax Az As A o A o OF a Figure 93 Trigger Settings Menu Select the Alarm Input tab Select the Alarm Input No in the dropdown list Edit the Alarm Name Select the trigger Type for the external alarm input device N O means Normal Open N C means Normal Close These two types can be selected Check the Enable Alarm Input checkbox to enable the selected alarm input Uncheck the checkbox to disable alarm input Click Handing Set to pop up the Handing menu as shown in Figure 94 Arming Schedule Handling PIZ Linking Cancel Figure 94 Trigger Chann
116. th the record schedule settings 6 Click the Apply button to save the settings 57 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTERS Playback 58 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Playing Back a Recording Previously recorded files can be played back using the Playback Interface You must first search for recordings to play them back Understanding the Playback Interface It s important to understand how to use the Playback Interface to efficiently navigate through recorded files To access the Playback Interface shown in Figure 57 go to Menu gt Playback gt Record Comet O aduta eee Quick Playback Playback Status Slop Cp Timo 0 1 Figure 57 Playback Interface Channel Full Screen Ch bier Calendar 53 l pets Preview Clip Backup Tools Playback Timeline Controls Clip Playbac Controls Figure 58 Playback Menu 59 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Figure 58 shows some of the main features of the Playback Interface which include e Channel Selector Select the channel to search for recordings on Calendar Select the date to search for recordings on Timeline Select the time to search for recordings on Preview Shows a preview of the selected recording Playback Controls Controls for playback of the selected recording Clip Backup Tools Tools to backup clips from a recording Clip Playback Controls Controls for playb
117. the right side of the menu shown in Figure 74 Genera DONS Email SNMP NAT More Settings Working Mode et Fault tolerance Figure 74 Network Settings Menu 74 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual 9 If you have a DHCP server running and would like your DVR to automatically obtain an IP address and other network settings from that server check the DHCP checkbox The assigned IP information via DHCP is now displayed in the IP address bar after enable DHCP and refreshes the interface Working Mode There are two 10M 100M 1000M NIC cards provided by the device and it allows the device to work in the Multi address Load Balance and Net Fault tolerance modes Multi address Mode The parameters of the two NIC cards can be configured independently You can select LAN or LAN in the NIC type field for parameter settings You can select one NIC card as default route And then the system is connecting with the extranet the date will be forward through the default route Load Balance Mode By using the same IP address and two NIC card share the load of the total bandwidth which enables the system to provide two gigabit network capacity Net Fault tolerance Mode the two NIC cards use the same IP address and you can select the Main NIC By this way in case of one NIC card failure the device will automatically enable the other standby NIC card so as to ensure the normal running of the whole system If you would
118. ubstream Capture Camera Analog 1 BS Bs Figure 46 Record Settings Menu Select the Pre record time The pre record time is the time in seconds to record before a recording is triggered Setting the pre record time to MAX will allow the DVR to use up to the maximum available buffer space for recording Select the Post record time The post record time is the time in seconds to also record after a recording has ended Enter the Erase Video After The Erase Video After time denotes the amount of days that files will be deleted after its initial recording Setting the time to 0 will allow the DVR to only delete and overwrite files when the HDD is full If check the Enable CABAC checkbox DVR will reduce the bit rate to improve the quality of image This feature is supported by analog cameras only 50 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Note You must click the Apply button after adjusting the configuration of each tab before you move on to adjust another one Note Event recordings are recordings that are triggered from motion detection and or from an external alarm See Configuring Alarms and Exceptions on Page 85 Note If an event occurs during Continuous recording the frame rate will automatically switch to that set for Event recording Note For holiday settings you can refer to Page 55 Configuring Record Schedule A record schedule allows you to schedule multiple time periods per day for reco
119. uit out of the menu without saving settings 47 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual CHAPTER4 Record Settings 48 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Settings for Recording There are multiple ways to setup your DVR for recording They include setting up a recording schedule triggering a recording by motion detection POS VCA and or a sensor alarm Configuring Recording Settings Before setting your DVR up for recording certain settings should be configured first The first set of settings to configure in this menu is the recording quality settings To configure the recording quality settings as following steps 1 Enter the Recording Quality Settings menu by going to Menu gt Recording Configuration gt Recording Quality as shown in Figure 44 a m TES AS yz Recording Confiquratio l Substream Record Capture Video amp Audio Figure 44 Recording Quality Settings Menu 2 Select main stream tab to configure the parameters of main stream 1 2 3 4 5 6 Select the camera to configure in the Camera dropdown list Select the Recording Mode to configure Both Continuous and Event can be configured Select the stream type in the Stream Type dropdown list The options include Video amp Audio and Video Select the camera resolution in the Resolution dropdown list Select the bit rate type in the Bitrate Type dropdown list The options for the camera bit
120. ure array Click OK to create array Click Array tab to view the successfully created array Click to select an array and click Create Vd to enter the Create Virtual Disk interface Cancel Figure 129 Create Virtual Disk Interface Edit the Virtual Disk Name Set the Capacity of the virtual disk And at least 100GB capacity must be configured for each virtual disk You can click the Information of Array Capacity area to set the remaining capacity of the array for the disk Select the Initialization Type from Background Foreground and Fast e Background The background initialization can synchronize the disks and detect and repair the bad sector of the disks During the background initialization the virtual disk is allowed to be used e Foreground Recommended By using foreground initialization the RAID will be initialized totally and the bad sector of the hard disks can be detected and repaired The virtual disk can be used only after the initialization is complete e Fast The fast initialization usually takes short time and only initializes part of the RAID and cannot detect the bad sector Click the Apply button to save the settings and click OK to return to the Array interface Click Virtual Disk tab to enter the virtual disk interface The successfully created virtual disk will be listed on the interface Enter the HDD Information interface and the virtual disk will display For operation guide of initializing the v
121. utton will select the next and previous day of or pause the video In Single Play mode pressing the Enter button will advance the video by a single frame Enter Button The Enter button is used to confirm selection in any of the menu modes It can be used to tick checkbox fields In Playback mode it can be used to play or pause the video In Single Play mode pressing the Enter button will advance the video by a single frame 4 Control Buttons 19 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual e 1 MENU Enter numerical 1 Access the main menu interface e 2ABC F1 Enter numeral 2 Enter letters ABC The F1 button can be used to select all items on the list In PTZ Control mode the F1 button can be used to zoom out zoom the PTZ camera In live view or playback mode the F1 button can be used to switch between main and spot video output e 3DEF F2 Enter numeral 3 Enter letters DEF In PTZ Control mode the F1 button can be used to zoom in zoom the PTZ camera The F2 button can be used to cycle through tab pages e 4GHI ESC Enter numeral 4 Enter letters GHI Exit and back to the previous menu e 5JKL EDIT Enter numeral 5 Enter letters JKL Delete characters before cursor Select the checkbox and ON OFF switch Start stop record clipping in playback e SHIFT Switch of compound keys between the numeric letter input and functional control e 6MNO PLAY Enter numeral 6
122. xport Process Bar Note Click the Refresh button if the connected local backup device cannot be displayed When it fails to detect the backup device please check whether it is compatible with the DVR You can format the backup device if the format is incorrect To view network status 1 Enter the Network Stat menu by going to Menu gt Maintenance gt Network Detection 2 Select the Network Stat tab to enter the Network Stat menu as shown in Figure 179 Iralhe Network Detection 4 096Kbps Obps Obps T6Mbps 240Mbps Figure 179 Network Stat Interface 3 Check the bandwidth of IP Camera Remote Live View Remote Playback Net Receive Idle and Net Send Idle 4 You can click the Refresh button to get the latest status 152
123. y button to save the settings Note Enable the Start Recording in the Display Menu will also create a schedule in Schedule Configuration It will start all day continue or event recording for all channels 54 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Holiday Settings Follow the steps to configure the holiday settings Steps 1 Enter the Holiday menu shown in Figure 53 by going to Menu gt Recording Configuration gt Holiday 15 bisa bisa bisa bisa bisa bisa bisa bisa bisa bisa bisa Figure 53 Holiday Settings Menu ri 2 Choose a holiday on the List show on the right Click to pop up an Edit menu as shown in Figure 54 Cancel Figure 54 Edit Menu Edit the Holiday Name or use the default one Check the Enable checkbox Select Mode in the dropdown list There are three different modes for the date format to configure holiday schedule 6 Set the start and end date 7 Click the Apply button and OK to save settings and exit a ad 55 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Configuring Settings for Capturing Configuring Capture Quality Settings Follow the introductions to configure capture quality settings Steps 1 Enter the Capture interface shown in Figure 55 by going to Menu gt Recording Configuration gt Recording Quality gt Capture O4 480 4CIF 04 480 4C1F v Medium TI s m T Figure 55 Capture Quality Settings Menu Select t
124. y menu as shown in Figure 32 Figure 32 Live View Strategy Menu 3 There are three strategies for selection Real time Balanced and Fluency 4 Click OK to save the settings Display POS Data on the Live Video Settings for configuring how to display POS information on live feed 1 Enter the POS configuration menu by going to Menu gt System Configuration gt POS 2 To handle how to display POS data click SET on the POS configuration interface a Trigger Channel Click the check box to select the camera s which will start recording of both video and POS data during the transaction Users can select one camera or multiple cameras to be triggered for each POS terminal 38 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Handling PIZ Linking Overlay Zone Figure 33 Handle Settings b Handling Click the check boxes to select different ways to notify user that transactions begin Trigger Channel PIZ Linking Overlay Zone Figure 34 Handle Settings c PTZ Linking Select the PTZ s which will start action preset patrol and pattern during the transaction Users can select one camera or multiple cameras to be triggered for each POS terminal 39 DS 7700NI SP 9000 9600 Series HDVR NVR User s Manual Trigger Channel Handling Overlay Zone e e Figure 35 PTZ Linking d Overlay Zone Use mouse to choose where on the screen should POS information be displayed The zone within the yell

Hikvision Digital Technology DS-9632NI-ST digital video recorder

Contents

Download Pdf Manuals

Related Search

Related Contents