Intel R2000WTXXX computer case
Contents
1. OxD4 Implication The POST Code Diagnostic LEDs may not be all off after POST has completed Status This issue was fixed in BMC 01 17 4151 and later release Workaround None 23 System only reports the first occurrence of power redundancy lost events Problem The integrated platform management subsystem will only report the first occurrence of a power redundancy lost event Any additional power redundancy lost events that may occur after the initial event will not be reported unless an AC cycle of the server is performed Implication With the first power redundancy lost event detected the system status LED will change the state to flashing Green and the system event log will display the event as shown below Power Unit Pwr Unit Redund 0x2 Informational event Pwr Unit Redund reports full redundancy has been lost Integrated BMC LUN 0 Channel 0 After hot swapping the faulty power supply which would change the state of the system back to normal system status LED goes back to solid Green the system will NOT report any further power redundancy lost events until an AC cycle of the server is performed Status This issue was fixed in BMC 01 17 4151 and later release Workaround None 11 Monthly Specification Update 24 System fan speed may not slow down as expected after hot swapping a failed fan within the Intel Server System R2000GZ GL Product Family Problem Implication Status Workaround System d2. Utility OFU under SuSE Linux Enterprise Server 11 64 bit with SP2 BMC continuously sends HDD assert de assert event during HDD RAID rebuild under ESRT2 14 Fixed mode of the SCU controller 15 Hard drives connected through SAS expander can t be detected in legacy mode Intel RAID C600 Upgrade Key replacement Issue 17 Intel LAN driver installation failure on Windows 7 18 On board VGA cannot be set to the highest resolution 1920x1080 and higher 19 i Fixed Hard drive locate LED may not instantly respond to the locate command if backplane is connected through SAS expander to a RAID controller Integrated BMC Web Console Sensor Readings Page Memory Throttling sensor status will stay Critical once triggered WOL Wake on LAN may not function under Red Hat Linux 6 2 64bit OS 22 POST Code Diagnostic LEDs may not be all off after POST has completed 23 System only reports the first occurrence of power redundancy loss 4 i Fixed System fan speed may not slow down as expected after hot swapping a failed fan within the e Intel Server System R2000GZ GL Product Family 2 Monthly Specification Update Description of Errata Intel FDR InfiniBand ConnectX 3 I O Module may not comply with FCC and Industry Canada regulations The Intel Xeon Phi Coprocessor PCI Express Card Status Sensor may show Unknown Fixed The Intel Xeon Phi Coprocessor PCI Express Card sensors numbering may not
3. Get Chassis Status command is issued after the Chassis Identify LED has been forced on the status of off 00b is returned for Chassis Identify State response data byte 4 bits 5 4 Unable to correctly read when the Chassis Identify LED is on This issue was fixed in BMC 01 10 3560 and later version None Monthly Specification Update 13 The BIOS and ME Firmware can t be updated successfully via Intel One Boot Flash Update Utility OFU under SuSE Linux Enterprise Server 11 64 bit with SP2 Problem OFU will fail to update BIOS amp ME under SuSE Linux Enterprise Server 11 64 bit with SP2 Operating System Implication If the system is running SuSE Linux Enterprise Server 11 64 bit with SP2 Operating System using OFU to update System Firmware Update Package SFUP will fail Status This issue was fixed in OFU version 11 0 Build 8 and later version Workaround None 14 BMC continuously sends HDD assert de assert event during HDD RAID rebuild under ESRT2 mode of the SCU controller Problem HDD fault will keep asserting and de asserting frequent during RAID rebuild under ESRT2 Implication During HDD ESRT2 RAID rebuild there s flood HDD fault assert deassert SAS RAID or Rebuild remap SATA RAID logs into SEL Status This issue was fixed in ESRT2 driver 15 00 0528 2012 and later version Workaround None 15 Hard drives connected through SAS expander can t be detected in legacy mode Problem If hard d
4. Problem Implication Status Workaround UEFI OS installation of Microsoft Windows Red Hat Linux or SUSE Linux may fail on AHCI or SCU controller when EFI Optimized Boot and Use Legacy Video for EFI OS are both enabled User may not be able to install UEFI OS under ESRT2 mode on Intel C600 Series Chipset based server boards Will not be fixed None Monthly Specification Update 4 HDD status LEDs do not function under specific configuration Problem Implication Status Workaround If drives are connected through expander to SCU ports and configured under RSTe mode the HDD status LEDs may not function properly HDD status LED may not show the HDD locate HDD fault or RAID rebuild message This issue was fixed in RSTe driver 3 2 0 1134 and later version None 5 RSTe GUI installation may fail if there are no devices attached to any onboard AHCI ports Problem Implication Status Workaround When Microsoft Windows 2008 R2 is installed on SCU ports the installation of RSTe drivers and the Graphic User Interface GUI in Windows 2008 R2 will fail if the AHCI controller is enabled while no device is attached to the AHCI SATA ports User may not be able to install RSTe GUI under mentioned configuration when the AHCI controller is enabled and no devices are attached to the AHCI SATA ports This issue was fixed in BIOS 01 03 0002 and later release None 6 BMC continuously sen
5. 6 8 and below may not be installed sucessfully on Windowns 7 with the bat installation scripts in the driver package Implication The LAN driver can not be installed by the bat installation scripts in the driver package Status The issue was fixed in Intel LAN driver 17 1 and later version Workaround None 18 On board VGA cannot be set to the highest resolution 1920x1080 and higher Problem The Graphics ID register in the on board video controller is getting set incorrectly Implication The video cannot be set to the highest resolutions listed here 1920x1080 High 256 Color 60 Hertz 1920x1200 High 256 Color 60 Hertz 1920x1080 High Color 16bit 60 Hertz Monthly Specification Update 1920x1200 High Color 16bit 60 Hertz Status This issue was fixed in BMC 01 16 4010 and later release Workaround None 19 Hard drive locate LED may not instantly respond to the locate command if backplane is connected through SAS expander to a RAID controller Problem If backplane is connected through SAS expander to a RAID controller the hard drive locate LED may not instantly respond to the locate command from the RAID controller The LED may blink after up to 2 minutes Implication The symptom doesn t happen if backplane is directly connected to the RAID controller Root cause has been identified in the motherboard BMC Status This issue was fixed in BMC 01 04 2896 and later release Workaround None 20 Integrated BMC
6. Monthly Specification Update Intel Server Board S2600GZ GL Intel Server System R1000GZ GL Product Family Intel Server System R2000GZ GL Product Family April 2015 Intel Server Boards and Systems Monthly Specification Update Revision History Modifications March 2012 Initial release Added errata 1 through 14 April 2012 Added documentation changes Vay 2072 June 2072 Juy 202 August 2072 September 2072 October 2072 November 2012 Updated errata 13 and 24 December 2012 Updated errata 5 18 21 and 22 May 2013 No update June 2013 Updated errata 26 July 2013 No update August 2073 September 2016 October 2073 November 2013 December 2013 January 2074 February 2074 April 2074 May 2014 June 2074 Juy 2074 August 2014 September 2014 November 2074 December 2074 April 2015 Monthly Specification Update Disclaimers The Monthly Specification Update Server System may contain design defects or errors known as errata that may cause the product to deviate from the published specifications Current characterized errata are documented in this Specification Update Information in this document is provided in connection with Intel products No license express or implied by estoppel or otherwise to any intellectual property rights is granted by this document Except as provided in Intel s Terms and Conditions of Sale for such products Intel assumes no liabilit
7. RKSAS8 RKSAS8R35 is installed to enable SAS support capablity under ESRT2 mode while SAS drivers are used the system may halt at the boot stage User may see a system halt with no RAID keys installed with SAS drivers used and ESRT2 enabled User should use SATA drives only if no RAID key installed This issue was fixed in BIOS 01 02 0003 and later version None Monthly Specification Update 10 Integrated BMC Web Console Power Statistics page Minimum wattage reads as zero Problem Implication Status Workaround On some systems the Integrated BMC Web Console Power Statistic page may display the Minimun wattage as zero OW after the system has been powered This reading will stay at zero until the next power cycle of the system This is an incorrect reading only and does not affect operation This issue was fixed in BMC 01 10 3560 and later version None 11 Integrated BMC Web Console Power Control page Perform Action button not functional Problem Implication Status Workaround After performing a Graceful shutdown from the Integrated BMC Web Console Power Control page the Perform Action button gets grayed out and cannot be pressed to request another action You cannot perform a power on of the system This issue was fixed in BMC 01 10 3560 and later version None 12 IPMI Get Chassis Status command returns incorrect Chassis Identify State Problem Implication Status Workaround When a
8. Web Console Sensor Readings Page Memory Throttling sensor status will stay Critical once triggered Problem When Memory Throttling is triggered the Memory P1 MTT and or P2 MTT sensor status will stay at Critical status in the Integrated BMC Web Console even after throttling has stopped Implication User may observe Memory P1 MTT and or P2 MTT status as Critical even when there is no throttling No functional impact to the system Status This issue fixed from ME 02 01 07 328 release Workaround Need a AC cycle or reset ME through IPMI to reset the MTT sensor status 21 WOL Wake on LAN may not function under Red Hat Linux 6 2 64bit OS Problem With Intel LAN driver version 17 1 WOL Wake on LAN may not function under Red Hat Linux 6 2 64bit OS Implication You may not be able to wake system through onboard NIC port Status This issue was fixed in LAN driver 17 4 and later release 10 Monthly Specification Update Workaround None 22 POST Code Diagnostic LEDs may not be all off after POST has completed Problem The POST Code Diagnostic LEDs should be all off after POST has completed But the LEDs may show other values after booting to an Operating System The codes seen could change at any time after POST or have any value A POST code of OxD4 has been observed after Microsoft Windows Server 2008 R2 completes loading There is no functional impact associated with the POST code pattern
9. be consistent with riser slot numbering The Activity Link LED of the the Intel I O Expansion Modules may not be solid green 29 Fixed Intel FDR InfiniBand ConnectX 3 I O Module AXX2FDRIBIOM port 2 may have interconnect i problem with Mellanox 1m FDR or 7m SFP passive copper cables 30 No fix BMC becomes temporarily unresponsive across the LAN or the Integrated BMC Web Console may disconnect when performing DC power cycling 31 The PXE boot and iSCSI boot settings may not be saved after reboot VMware ESxi installation failure when detecting Network Adapters 33 Fixed When using the 3ware RAID controller cards the system may hang after creating RAID logic volume with BIOS R02 01 0002 or R02 02 0002 Do Updated Technical product specification TPS rev2 3 Remove the Battery Failure from Table37 and Table51 Windows Server 2008 R2 installation on Intel Xeon E5 2600 v2 processor based server boards may fail with an accessory 2U PCI X riser A2ULPCIXRISER installed 35 No fix 6 System will hang during POST if two CPUs are mismatched 3 Table 2 Documentation Changes Document Name Description of Documentation Change Publish Intel _ Server System R1000GZ GL Product Family Technical Product Updated to Rev 2 2 Specification r P Publish Intel Server System R2000GZ GL Product Family Technical Product Updated to Rev 2 2 Specification Publish Intel Server Board S2600GZ GL Technical P
10. ds RAID volume rebuild event in RSTe mode of the SCU controller Problem Implication Status Workaround When RSTe RAID is in degraded mode and a drive is inserted to start the RAID rebuild System Event Log SEL records drive plug and rebuild events and then continuously sends a rebuild event message User may see the SEL flooded with RAID volume rebuild event entries This issue was fixed in latest RSTe driver ver 3 0 0 3020 upd 2012 03 03 None Monthly Specification Update 7 System may halt under specific BIOS configurations Problem Implication Status Workaround Once BIOS options EFI Optimized Boot and Memory Mapped I O Above 4GB are both enabled and RSTe mode is selcted system may halt during the system POST User may see system hang with mentioned configuration This issue was fixed in BIOS 01 03 0002 and later version None 8 Microsoft Windows 2003 x86 installation failure under Pass through mode of SCU controller Problem Implication Status Workaround Microsoft Windows Server 2003 x86 installations on SCU RSTe pass through mode fail User may not able to install Microsoft Windows Server 2003 x86 on mentined BIOS configuration This issue may be fixed in a future RSTe driver release None 9 System may halt under unsupported configuration in ESRT2 mode Problem Implication Status Workaround If no Intel C600 RAID upgrade key any of RKSAS4 RKSAS4R5
11. e can be fixed by disabling this BIOS option Memory Mapped I O above 4GB is enabled by default in the latest BIOS Customers have to disable this option to make VMware ESxXi all versions installation successful 33 When using the 3ware RAID controller cards the system may hang after creating RAID logic volume with BIOS RO2 01 0002 or RO2 02 0002 Problem When installing the 3ware RAID controller card in certain PCle slots the system may hang after creating RAID logic volume with BIOS R02 01 0002 or BIOS RO2 02 0002 15 Monthly Specification Update Implication Customers may observe a system hang when using the 3ware RAID controller card to create RAID logic volume Status This issue was fixed by BIOS RO2 03 0001 and later release Workaround None 34 Updated Technical product specification TPS rev2 3 Remove the Battery Failure from Table37 and Table51 35 Windows Server 2008 R2 installation on Intel Xeon E5 2600 v2 processor based server boards may fail with an accessory 2U PCI X riser A2ULPCIXRISER installed Problem The system may not be able to install Windows Server 2008 R2 with below configurations 1 An Intel Xeon E5 2600 v2 processor is installed 2 A 2U PCI X riser AZULPCIXRISER is installed Implication Users may not be able to install Windows Server 2008 R2 with mentioned configurations Status This issue will not be fixed Workaround None 36 System will ha
12. ees 5 5 RSTe GUI installation may fail if there are no devices attached to any onboard AHCI ports5 6 BMC continuously sends RAID volume rebuild event in RSTe mode of the SCU controller 5 7 System may halt under specific BIOS configurations ssessssesssesseeeseeeeeees 6 8 Microsoft Windows 2003 x86 installation failure under Pass through mode of SCU controller 6 9 System may halt under unsupported configuration in ESRT2 mode 0008 6 10 Integrated BMC Web Console Power Statistics page Minimum wattage reads as zero 7 11 Integrated BMC Web Console Power Control page Perform Action button not functional 7 12 IPMI Get Chassis Status command returns incorrect Chassis Identify State 7 13 The BIOS and ME Firmware can t be updated successfully via Intel One Boot Flash Update Utility OFU under SuSE Linux Enterprise Server 11 64 bit with SP2 8 14 BMC continuously sends HDD assert de assert event during HDD RAID rebuild under ESRT2 mode of the SCU controller cccccccccccccccceeeeceeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 8 15 Hard drives connected through SAS expander can t be detected in legacy mode 8 16 Intel RAID C600 Upgrade Key replacement ISSUE ccceeeeeeeeeeeetteeeeeeeeeeeeeee 9 17 Intel LAN driver installation failure on Windows 7 ccccccceeeeeeeeeeeeeeeeeeeeeeeeeeees 9 18 On board VGA cannot be set to the highest resol
13. erver System R1000GZ GL Product Family Technical Product Specification 3 Intel Server System R2000GZ GL Product Family Technical Product Specification It is intended for hardware system manufacturers and software developers of applications operating systems or tools It will contain specification changes specification clarifications errata and document changes Nomenclature 1 Specification Changes are modifications to the current published specifications for Intel server boards These changes will be incorporated in the next release of the specifications 2 Specification Clarifications describe a specification in greater detail or further highlight a specification s impact to a complex design situation These clarifications will be incorporated in the next release of the specifications 3 Documentation Changes include typos errors or omissions from the current published specifications These changes will be incorporated in the next release of the specifications 4 Errata are design defects or errors Errata may cause the server board behavior to deviate from published specifications Hardware and software designed to be used with any given processor stepping must assume that all errata documented for that processor stepping are present on all devices Product Scope The following specific boards BIOS and components are covered by this update Baseboard PBA BIOS BMC FRU SDR Revision Revision Revision Revision Product C
14. erver system the card status sensor MIC 1 Status or MIC 2 Status may show Unknown in Intel Integrated BMC Web Console Users may not get the correct MIC status in Intel Integrated BMC Web Console There is no function impact to the server system This issue doesn t happen when two Intel Xeon Phi Coprocessor PCI Express Cards are installed This issue was fixed in BMC 01 19 5018 and later release Workaround Monthly Specification Update None 27 The Intel Xeon Phi Coprocessor PCI Express Card sensors numbering may not be consistent with riser slot numbering Problem Implication Status Workaround The Intel Xeon Phi Coprocessor PCI Express Card MIC card sensors numbering may not be consistent with riser slot numbering on the server board When an Intel Xeon Phi Coprocessor PCI Express Card is installed in the server system in Intel Integrated BMC Web Console the card sensor may show MIC 2 Status and MIC 2 Margin if the card is installed on RISER SLOT_1 and MIC 1 Status and MIC 1 Margin if the card is installed on RISER SLOT_2 Users need to read MIC 2 sensors for a card installed on RISER SLOT_1 and read MIC 1 sensors for a card installed on RISER SLOT_2 There is no functional impact on the server system This issue was fixed in BMC 01 20 5446 and later releases None 28 The Activity Link LED of the Intel I O Expan
15. ng during POST if two CPUs are mismatched Problem If two CPUs are mismatched with different model cache size frequency or stepping the server system may hang during POST and the status LED may still show green color and the system diagnostic LED shows 0xDC code Implication The server system cannot boot up and the status LED may not be changed from green to amber color Status This issue will not be fixed Workaround Customer should use the same two CPUs on the server system and verify the CPU model cache size frequency and stepping before installing them 16
16. nloading http www mellanox com page firmware_table_ Intel The AXX2FDRIBIOM still has limited issues with Mellanox 1m FDR passive copper cable that may be fixed in the future Workaround Port 2 of AXX2FDRIBIOM must be used with Mellanox 2m or 3m FDR or 1m 2m 3m 5m or 7m SFP passive copper cables or active optical cables 30 BMC becomes temporarily unresponsive across the LAN or the Integrated BMC Web Console may disconnect when performing DC power cycling Problem When using a complex network infrastructure like switches with advanced features e g spanning tree and performing a DC power cycle there may be unexpected behavior by the BMC The BMC may become unresponsive on the LAN connection or the Integrated BMC Web console will disconnect Implication The shared NIC PHY is reset when there is a DC power on This is expected behavior of NIC PHY Current BMC has no method to avoid this reset Status This issue will not be fixed Workaround None 31 The PXE boot and iSCSI boot settings may not be saved after reboot Problem The PXE boot and iSCSI boot settings may not be saved after reboot on the Intel Server Board S2600GZ GL with the following PBA Printed Board 14 Implication Status Workaround Monthly Specification Update Assembly numbers G11481 352 G11481 353 G29051 353 G11481 354 and G29051 354 The Intel Server Board S2600GZ GL with other PBA numbers are not impacted The PBA number can be found
17. ode ME Revision Monthly Specification Update Summary Tables of Changes The following tables provide an overview of known errata and known document changes that apply to the specified Intel Server Products The tables use the following notations Doc Intel intends to update the appropriate documentation in a future revision Fix Intel intends to fix this erratum in the future Fixed This erratum has been previously fixed No Fix There are no plans to fix this erratum Shaded This erratum is either new or has been modified from the previous specification update Table 1 Errata Summary Description of Errata Linux Operating Systems are not supported on RSTe mode 2 UEFI Windows Server 2008 R2 SP1 installation on SCU ports may fail under RSTe RAID mode UEFI Operating System installation is not supported on ESRT2 mode HDD status LEDs do not function under specific configuration 5 RSTe GUI installation may fail if there are no devices attached to any onboard AHCI ports BMC continuously sends RAID volume rebuild event in RSTe mode of the SCU controller System may halt under specific BIOS configurations System may hal under specife BIOS configurations 8 Fr Wicrosot Windows 2003 x86 installation failure under Pass through made of SCU controler 9 Fred System may hait under unsupported confuraton n ESATmode 3 i A Fixed The BIOS and ME Firmware can t be updated successfully via Intel One Boot Flash Update
18. oes not recognize a hot swapped fan causing the fans to run at high speed After a system fan failure the remaining fans will speed up to maintain proper system cooling After replacing the failed fan with a new one the system will continue to operate fans at high speed until a system reboot is performed This issue was fixed in FRUSDR 1 07 and later release None 25 Intel FDR InfiniBand ConnectxX 3 I O Module may not comply with FCC and Industry Canada regulations Problem Implication Status Workaround Intel FDR InfiniBand ConnectX 3 I O Module AXX1FDRIBIOM and AXX2FDRIBIOM may not comply with Part 15 of the Federal Communications Commission FCC and Industry Canada regulations when used with copper InfiniBand cables Except for not complying with FCC and Industry Canada regulations when used with copper InfiniBand cables no other functionality impact And except for the United States of America and Canada where the regulations apply no other countries are impacted This issue was fixed by Mellanox InfiniBand ConnectX 3 firmware 2 11 1308 and later release Please refer to the following website for downloading http www mellanox com page firmware_table Intel None 26 The Intel Xeon Phi Coprocessor PCI Express Card Status Sensor may show Unknown Problem Implication Status 12 When only one Intel Xeon Phi Coprocessor PCI Express Card MIC card is installed in the s
19. olid green13 29 Intel FDR InfiniBand ConnectxX 3 I O Module AXX2FDRIBIOM port 2 may have interconnect problem with Mellanox 1m FDR or 7m SFP passive copper cables 14 30 BMC becomes temporarily unresponsive across the LAN or the Integrated BMC Web Console may disconnect when performing DC power cycling eeeeeeeeeeeeeeeeeeeeeeeee 14 31 The PXE boot and iSCSI boot settings may not be saved after reboot 14 32 VMware ESXi installation failure when detecting Network Adapters 0 15 33 When using the 3ware RAID controller cards the system may hang after creating RAID logic volume with BIOS R02 01 0002 or RO2 02 0002 20 0 0 cece eeeeeeeeeeeeeeeeeeeeeeeetneeeeeeees 15 34 Updated Technical product specification TPS rev2 3 Remove the Battery Failure ifort Fables and Tabled scilciesciieotnivrwcteeianenieneinandtna ERE E AERA 16 35 Windows Server 2008 R2 installation on Intel Xeon E5 2600 v2 processor based server boards may fail with an accessory 2U PCI X riser A2ULPCIXRISER installed 16 36 System will hang during POST if two CPUs are mismatched seeeeeeee 16 Vi Monthly Specification Update lt This page is intentionally left blank gt Monthly Specification Update Preface This document is an update to the specifications contained in the following documents 1 Inte Server Board S2600GZ GL Technical Product Specification 2 Intel S
20. on the label attached to the server board or in the server board FRU Field Replaceable Unit information The saved settings in the following two usage models may change back to factory defaults after reboot 1 PXE Boot When the PXE 1GbE Option ROM is set to Enabled by default in BIOS Setup gt Advanced gt NIC Configuration the Setup Menu Wait Time can be changed from 2 seconds by default to other values in the Intel Boot Agent GE Setup Menu during system boot and the settings should be saved after reboot 2 iSCSI Boot When the iSCSI 1GbE Option ROM is set to Enabled in BIOS Setup gt Advanced gt NIC Configuration the iSCSI Boot Configuration can be changed from dynamic IP by default to static IP in Intel iSCSI Remote Boot Setup Menu during system boot and the settings should be saved after reboot The issue was fixed by EEPROM Unlock Utility revision 1 0 1 and later release Please refer to the following website for downloading https downloadcenter intel com Detail Desc aspx agr Y amp DwnldID 23609 None 32 VMware ESXi installation failure when detecting Network Adapters Problem Implication Status Workaround The system may encounter a failure when installing VMware ESXi OS and the error messages could be No Network Adapters Users may not be able to successfully install the VMware ESXi all versions VMware does not support Memory Mapped I O above 4GB This issu
21. rives are connected through expander to SCU ports and configured under RSTe mode the hard drives can t be detected by system in legacy mode default BIOS setting Implication Users can t use the hard drives connected through expander as boot device to install OS But users can install OS to other hard drives which are not connected through expander and load RSTe driver to make the hard drives connected through expander visible to OS Or users can change Boot Options gt EFI Optimized Boot to Enabled in BIOS Setup so that hard drives connected through expander can be detected by the system Status This issue was fixed in BIOS 01 08 0003 and later release Monthly Specification Update Workaround None 16 Intel RAID C600 Upgrade Key replacement Issue Problem With Manageability Engine ME Firmware 02 01 05 069 the server may detect the incorrect Storage Control Unit SCU Redundant Array of Inexpensive Independent Disks RAID information after installing or replacing the RAID upgrade key The board or system may still show the previous RAID information even if you replace the key with a new one Implication With the ME firmware 02 01 05 069 the system may not detect the new RAID activation key during the first time AC power on Status The issue was fixed in ME firmware 02 01 05 091 and later version Workaround None 17 Intel LAN driver installation failure on Windows 7 Problem The Intel LAN driver version 1
22. roduct Specification Updated to Rev 2 3 The following sections provide in depth descriptions of each erratum documentation change indicated in the tables above The errata and documentation change numbers referenced in the following sections correspond to the numbers in the tables above Monthly Specification Update Errata 1 Linux Operating Systems are not supported on RSTe mode Problem Implication Status Workaround Intel RSTe mode is not supported on Red Hat Linux and SUSE Linux User may not able to install Red Hat Linux and SUSE Linux on Intel C600 Series Chipset based Server Boards under Intel RSTe mode This issue may be fixed in future driver or BIOS releases None 2 UEFI Windows Server 2008 R2 SP1 installation on SCU ports may fail under RSTe RAID mode Problem Implication Status Workaround System may encounter blue screen when installing Windows Sever 2008 R2 SP1 under UEFI with below configurations 1 Intel C600 RAID Upgrade Key is installed and SAS HDDs are used on SCU ports 2 BIOS options EFI Optimized Boot and Use Legacy Video for EFI OS are enabled 3 Under RSTe RAID mode User may not able to install UEFI Windows Server 2008 R2 SP1 on Intel C600 Series Chipset based Server Boards with mentioned configuration This issue was fixed in BIOS 01 03 0002 and later version None 3 UEFI Operating System installation is not supported on ESRT2 mode
23. sion Modules may not be solid green Problem Implication Status Workaround The Activity Link LED on the left side of the following Intel I O Expansion Modules may not be solid green when there is active connection e Dual Port Intel X540 10GbE I O Module AXX10GBTWLIOM and AXX10GBTWLHW e Dual Port Intel 82599 10GbE I O Module AXX10GBNIAIOM The LED may keep off instead of solid green Users can t figure out whether an active connection is established through LED behavior This issue was fixed with new EEPROM cut in at factory see PCN112163 for more details None 13 Monthly Specification Update 29 Intel FDR InfiniBand ConnectX 3 I O Module AXX2FDRIBIOM port 2 may have interconnect problem with Mellanox 1m FDR or 7m SFP passive copper cables Problem Intel FDR InfiniBand ConnectX 3 I O Module AXX2FDRIBIOM port 2 may have interconnect problem when used with Mellanox 1 meter FDR or 7 meters SFP passive copper cables Implication When used with Mellanox 1m FDR or 7m SFP passive copper cables port 2 of the module may not be able to establish a successful connection for signal transmission This issue does not impact other cables This issue does not impact Intel FDR InfiniBand ConnectX 3 I O Module AXX1FDRIBIOM Status The issue with 7m SFP passive copper cable was fixed by Mellanox InfiniBand ConnectX 3 firmware 2 11 1308 and later release Please refer to the following website for dow
24. ution 1920x1080 and higher 9 19 Hard drive locate LED may not instantly respond to the locate command if backplane is connected through SAS expander to a RAID controller ccccccccccseeeeeeeeeees 10 20 Integrated BMC Web Console Sensor Readings Page Memory Throttling sensor status will stay Critical once triggered cece eceeeeeee teeter eeeeeeeaeeeeeeeeeeeeeeeteeesaaees 10 21 WOL Wake on LAN may not function under Red Hat Linux 6 2 64bit OS 10 22 POST Code Diagnostic LEDs may not be all off after POST has completed 11 23 System only reports the first occurrence of power redundancy lost events 11 24 System fan speed may not slow down as expected after hot swapping a failed fan within the Intel Server System R2000GZ GL Product Family cccceeeesseeeeteeeeeeeeeeeeee 12 25 Intel FDR InfiniBand ConnectX 3 I O Module may not comply with FCC and Industry Canada regulations wiiecciccciccmencintaiaeapomnebenenmncieetunncienivastdeddesaucewadeawanwbesauasebbemeeaneis 12 Monthly Specification Update 26 The Intel Xeon Phi Coprocessor PCI Express Card Status Sensor may show Unknown 12 27 The Intel Xeon Phi Coprocessor PCI Express Card sensors numbering may not be consistent with riser Slot numbering cceeeeeeeeeeeeeeeeeeeeeeeeeeeeenaeeeeeeeeeeeeeeeenennaaaaes 13 28 The Activity Link LED of the Intel I O Expansion Modules may not be s
25. y whatsoever and Intel disclaims any express or implied warranty relating to sale and or use of Intel products including liability or warranties relating to fitness for a particular purpose merchantability or infringement of any patent copyright or other intellectual property right Intel products are not intended for use in medical life saving or life sustaining applications Intel may make changes to specifications and product descriptions at any time without notice Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order Intel Itanium Pentium and Xeon are trademarks or registered trademarks of Intel Corporation Other brands and names may be claimed as the property of others Copyright Intel Corporation 2015 Monthly Specification Update Contents PROT ACE ETET ETET TTT TTT T E E E T E 1 Summary Tables of Changes sssssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn nnana 2 e A E E 4 1 Linux Operating Systems are not supported on RSTe MOdE eeeeeeeeeeeereeeeees 4 2 UEFI Windows Server 2008 R2 SP1 installation on SCU ports may fail under Role RAID Mods saca seses ets ne cane adnt on age ecacunientiint tanec Garena mitoa amet 4 3 UEFI Operating System installation is not supported on ESRT2 mode 06 4 4 HDD status LEDs do not function under specific configuration cceeeeee
Download Pdf Manuals
Related Search