StarTech.com Height Adjustable Monitor Arm - Grommet / Desk Mount with Cable Hook
Contents
1. 2 Place the EVA Cushion 4 beneath the Support Post 1 and thread the Hand Screw 13 from below until secure Ensure that the Pressure Plate 14 is making full contact with the desk surface Desk Mount 1 Attach the Large C Clamp 3 and Small C Clamp 6 pieces using 4 M6x12mm Screws 8 as shown depending on the thickness of your desk table Desk Thickness Desk Thickness lt 50mm 2in gt 50mm 2 Cc Instruction Manual Sta rle chom 3 Hard to find made easy 2 Slide the Hand Screw 13 through the bottom of the clamp and attach the Pressure Plate 14 using the Male Round Washer 11 Female Round Washer 12 and M4x15mm Phillips Screw 10 3 Attach the completed Desk Clamp to base of the Support Post 1 using 4 M5x14mm Hex Screws 9 M5 x1l4mm 4 Place the EVA Cushion 4 beneath the Support Post 1 and then place the Desk Clamp opening around the edge of your desktop in your desired location Tighten by hand to secure ensuring that the clamp is making full contact with the desk surface Starlechscam 4 Hard to find made easy Instruction Manual Desk Thickness 0 110mm 4in Attaching the Display 1 Carefully place your display face down on a protective surface to access the mounting points LCD display Protective Surface 2 Attach the display to the Monitor Mount 2 using the 4 Thumb Screws 5 IT i Starlechcom 5 Hard to find made easy I2. Starlechcom Hard to find made easy Desk Mount Monitor Arm with Cable Management amp Height Adjust ARMPIVOT actual product may vary from photos DE Bedienungsanleitung de startech com FR Guide de l utilisateur fr startech com ES Guia del usuario es startech com IT Guida per l uso it startech com NL Gebruiksaanwijzing nl startech com PT Guia do usuario pt startech com For the most up to date information please visit www startech com Manual Revision 06 23 2014 FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet o
3. e 5 Completing the Assembly ssssssssssesesssssssssssseeeeessssssssccereeesossssssseeereeeesonssseeeeereeeossssssseeerresssssssseeeeressssssss 6 Adjusting Monitor Mount Resistance esssssssesssssseeressssssessssssssereosseeereossssseeossssssereessserresssssseeesssssee 7 SVS CU AN N esaea aa AAi 8 Technical SUD DOF E narisan 9 Warranty I TOrMAtlOn vinci cesecssqsaccccereacahncacsensaessnsvecsecsorsteavertecseanaeniveenes 9 Cc Instruction Manual sta rlech 0m i Hard to find made easy Introduction Packaging Contents Support Post Qty 1 EVA Cushion Qty 1 cf 1 7 Cable Clip Collar attached M4x15mm Phillips Screw Hand Screw Pressure Plate attached attached Qty 1 Qty 1 Instruction Manual Large C Clamp Qty 1 M3 2 5mm Allen Wrench Qty 1 Starlechscam Hard to find made easy Product Diagram 360 302 MAX 20MM 110MM Units mm Installation Warning It is the installer s responsibility to ensure that the combined weight of all components does not exceed the maximum 14 kg 30 9 Ibs weight capacity of the mounting arm Desk Grommet Mounting The Monitor Arm can be clamped to a desk table or mounted through a grommet hole Instructions for both will be provided in the following sections Starlechscam 2 Hard to find made easy Instruction Manual Grommet Mount 1 Remove the Hand Screw 13 from the base of the Support Post 1
4. n a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of Trademarks Registered Trademarks and other Protected Names and Symbols This manual may make reference to trademarks registered trademarks and other protected names and or symbols of third party companies not related in any way to StarTech com Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech com or an endorsement of the product s to which this manual applies by the third party company in question Regardless of any direct acknowledgement elsewhere in the body of this document StarTech com hereby acknowledges that all trademarks registered trademarks service marks and other protected names and or symbols contained in this manual and related documents are the property of their respective holders Starlechcom Hard to find made easy Instruction Manual Table of Contents PPPEEO QUIGTION anna Ea 1 Packaging ONESIES cecescavsczscacscadera ccslcseesssssatbanaicbasssasisatijnmencerscoosatasaedeaeestssitstsuasiastsmamamnenamansioanaest 1 Product DlaG ram sonnia inaa aaan 2 Installationer Ni 2 Desk Grommet Mounting sssesesessessssessssseesssseeosssereosseesssseressseossseeronsseeesseeeosssereosereossseresseronsseerossseossseees 2 Attaching the Display eee ry eee nee mere eT see mn mar oe ere re eer eco e
5. nstruction Manual WARNING Do not over tighten the screws and stop immediately if you encounter resistance to avoid damage to your display Ensure that all spacers and screws being used are the same length and thread type Completing the Assembly 1 Loosen the Cable Clip Collar 7 on the Support Post 1 and adjust to the desired height 2 Slide the Monitor Mount 2 onto the Support Post 1 until it rests on the Collar 7 and tighten the set screw using the M3 Allen Wrench 15 Instruction Manual Sta rlechcom 6 Hard to Find made easy Adjusting Monitor Mount Resistance WARNING Forced movement of the Mount Bracket without loosening the screws may damage the product or the mounted displays Always support your display from underneath when making any adjustments to the LCD Arms or Mount Brackets to avoid damage to the display Note For all adjustments outlined below turning the screw clockwise will increase the resistance while turning the screw counter clockwise will decrease resistance To increase decrease the tilt resistance adjust the set screw located on the side of the Monitor Mount joint using the M3 Allen Wrench 15 y To increase decrease swivel resistance adjust the set screw located on the side of the Monitor Mount bracket at the Support Post using the M3 Allen Wrench 15 Place the wrench in the collar when not in use W RM E Starlechcom 7 Hard to find made easy Ins
6. truction Manual Specifications Weight Capacity 30 9 Ibs 14 kg Max Display Size 30 VESA Compatibility 75x75 mm and 100x100 mm Maximum Mounting Surface Thickness Starlechcom 8 Hard to find made easy Instruction Manual Technical Support StarTech com s lifetime technical support is an integral part of our commitment to provide industry leading solutions If you ever need help with your product visit www startech com support and access our comprehensive selection of online tools documentation and downloads For the latest drivers software please visit www startech com downloads Warranty Information This product is backed by a two year warranty In addition StarTech com warrants its products against defects in materials and workmanship for the periods noted following the initial date of purchase During this period the products may be returned for repair or replacement with equivalent products at our discretion The warranty covers parts and labor costs only StarTech com does not warrant its products from defects or damages arising from misuse abuse alteration or normal wear and tear Limitation of Liability In no event shall the liability of StarTech com Ltd and StarTech com USA LLP or their officers directors employees or agents for any damages whether direct or indirect special punitive incidental consequential or otherwise loss of profits loss of business or any pecuniary loss arising o
7. ut of or related to the use of the product exceed the actual price paid for the product Some states do not allow the exclusion or limitation of incidental or consequential damages If such laws apply the limitations or exclusions contained in this statement may not apply to you Starlechcom 9 Hard to Find made easy Instruction Manual Starlechcom Hard to find made easy Hard to find made easy At StarTech com that isn t a slogan It s a promise StarTech com is your one stop source for every connectivity part you need From the latest technology to legacy products and all the parts that bridge the old and new we can help you find the parts that connect your solutions We make it easy to locate the parts and we quickly deliver them wherever they need to go Just talk to one of our tech advisors or visit our website You ll be connected to the products you need in no time Visit www startech com for complete information on all StarTech com products and to access exclusive resources and time saving tools StarTech com is an ISO 9001 Registered manufacturer of connectivity and technology parts StarTech com was founded in 1985 and has operations in the United States Canada the United Kingdom and Taiwan servicing a worldwide market
Download Pdf Manuals
Related Search