Foster Rondò Kristal White.3F.STD
Contents
1. Foster a Live the Quality OPERATION AND MAINTENANCE MANUAL RONDO gas cooker hobs cod 052 142 7052 642 Foster spa via M S Ottone 18 20 42041 Brescello RE Italy www fosterspa com tel 39 0522 687425 tel Servizio Assistenza 39 0522 684450 fax 39 0522 686019 fax Servizio Ricambi 39 0522 962166 e mail service fosterspa com INSTALLATION INSTRUCTIONS TECHNICAL DATA MODELS Burners Automatic Safety Product dimensions Cut out dimensions ignition rave _ W x D in mm W x D in mm JAJSR R TC o o O SEE e e o a 500 Installation The purchaser is responsible for installation the Manufacturer does not offer this service Any technical assistance activities carried out by the Manufacturer relating to faulty installation are not covered by the warranty The built in hobs are designed for installation on worktops made of any material provided these are between 25 mm and 40 mm thick and can withstand temperatures of 100 C If the hob is installed adjacent to a cabinet on any one of the two sides at least 150 mm must divide the hob edge from the cabinet while the distance between the rear wall and hob edge must be at least 50 mm A partition made of insulating material wood or similar must be inserted in the underlying cabinet at least 20 mm from the bottom edge of the hob Pea eZ EE 25 40mm HI Securing t2. anti clockwise to increase the gas flow and clockwise to reduce the gas flow until the flame is 3 4 mm long For LPG in cylinder turn the by pass clockwise until it reaches the end COOKER HOB OPERATION Instructions for the user This appliance is designed for domestic cooking purposes and must be operated for its intended use only Any other use of the appliance constitutes improper use and is dangerous The manufacturer shall not be held liable for any damages resulting from improper incorrect or unreasonable use Operating the burners If the burners have not been used for several days wait a few seconds before igniting them to enable the air in the piping to escape The burners are equipped with an automatic ignition device and can be ignited by simply turning the knob towards the small star symbol The ignition generator is of the repetitive discharge type If the flame does not ignite within 5 seconds turn the knob back to position 0 and repeat the operation On models equipped with a flame safety device that interrupts the flow of gas should the flame accidentally extinguish the burners can be ignited in the above mentioned manner provided the knob is kept fully depressed for roughly 5 6 seconds after the flame ignites After this time which is necessary to engage the safety device the flame burns permanently CAUTION after cleaning the hob make sure that the burner is properly inserted in its housing and does not
3. interfere with the spark plug For more efficient use of the burners we recommend using flat bottomed pots with suitable diameter in relation to the chosen burner When using small diameter cookware coffee pots tea pots etc adjust the burner power so that the flame does not spread over the edges of the cookware Do not use cookware with concave or convex bottom WARNING should the burner flame accidentally extinguish shut off the control knob and attempt to reignite the burner after at least 1 minute CLEANING AND MAINTENANCE Prior to carrying out any maintenance on the hob unplug the appliance or disconnect it from the power supply by shutting off the mains switch Wait for the appliance to cool down before effecting cleaning operations wash any enamelled painted or chrome plated parts with the aid of warm water and soap or a non corrosive liquid detergent Steel parts can be cleaned with methylated spirits or other specific products available on the market Use cotton or a cloth wetted with vaseline or seed oil to clean aluminium profiles and panels Clean then wipe using methylated spirits Never use abrasive or corrosive detergents bleach or acids for cleaning operations Avoid leaving acidic or alkaline residues lemon juice vinegar etc on enamelled painted or stainless steel parts TECHNICAL ASSISTANCE Verify the following before contacting the Technical Assistance Service In the event of cooker hob malfunctions we r
4. pipe does not lie in the path of moving parts in the underlying cabinet e g drawers and that its position safeguards it against possible damage ADJUSTMENT FOR DIFFERENT TYPES OF GAS To adjust the gas hob for a different type of gas to that originally intended follow the steps below in the sequence indicated Remove the pan support and burner Unscrew the injectors M using a suitable plug spanner and replace them with injectors whose diameter is appropriate for the type of gas to be used see the Burner specifications table After completing the procedure replace the old calibration plate with the one provided relative to the new installation BURNER SPECIFICATIONS SR R 1 1 75 3 00 1 00 0 55 0 90 1 30 Rated heat input k Reduced heat input k minimum heat input DE AT k INJECTOR G30 G31 28 30 30 37 mbar G30 G31 50 mbar m G20 20 mbar m G25 25 mbar m G25 20 mbar m G110 8 mbar G120 8 mbar mm 1 40 O BY PASS Co eee eae G30 G31 28 30 30 37 mbar W W W LA mm 0 85 m m m 0 72 m mm m mm 1 G25 20 mbar mm HOB SPECIFICATIONS Total power output Consumption kW Po G30gh G20 m8 h G25 m8 h G110 m8 h G120 m8 h I MINIMUM FLOW ADJUSTMENT 11 Switch the burner on set the valve to the minimum position then remove the knob it is pressure fitted thus easily removable Use a small screwdriver to turn the valve adjustment screw
5. 25 01 1992 which implements European Directive 89 109 EEC CE Appliance manufactured in conformity to European Directives 90 396 EEC 89 336 EEC 93 68 EEC 73 23 EEC and subsequent amendments Connection options RETE DI ALIMENTAZIONE TERRA EI i CAVO DI ELETTRICA ALIMENTAZIONE NEUTRO N GAS CONNECTION Appropriate rating plates on the gas cooker hob indicate the type of gas for which the hob is configured However the appliance can be operated with other types of gas after carrying out simple adjustments See indications in the following paragraphs Connection to the gas supply Connection of the appliance to the gas piping or cylinder must be carried out in conformity to the UNI CIG7129 and 7131 standards after verifying that the hob is suitably configured for the intended type of gas If not carry out the operations indicated in the paragraph lt lt Adjustment for different types of gas gt gt In the event of liquid gas supply from a cylinder use pressure valves that conform to UNI CIG 7432 specifications Important in order to ensure safe operation optimal energy consumption and appliance durability make sure that the supply pressure complies with the values indicated in the Burner specifications table on page 5 Installation of the gas pipe fitting The instructions are intended for personnel authorised to install the appliance in conformity to UNI CIG 7131 specifications All operations must be
6. carried out while the appliance is disconnected from the power supply CAUTION two different fittings are included in the packaging one cylindrical and the other conical Select the most appropriate type depending on the country of installation CYLINDRICAL CONICAL Installation steps Screw the adjustable fitting onto the gas rail feed pipe with cylindrical size 1 2 male gas thread on the appliance A1 with the appropriate sealing gasket A2 Tighten the fitting thoroughly while making sure it lies in the right direction Connect the cooker hob to the gas supply line by screwing the supply pipe to the adjustable fitting and inserting the sealing gasket 10 A1 Gas rail pipe A2 Gasket A3 Adjustable fitting A4 Rigid or flexible gas supply pipe x T E IT Ag Exclusively use pipes that conform to UNI CIG 9891 specifications and sealing gaskets that conform to UNI CIG 9264 specifications The pipes must be installed so that when fully extended their length does not exceed 2 000 mm To facilitate installation and avoid the risk of gas leaks it is advisable to first connect the adjustable fitting to the cooker hob then subsequently to the gas supply pipe Inverting this sequence may not guarantee a gas tight connection between the pipe and hob Important after completing installation verify the perfect tightness of all the fittings using a soapy solution never a flame Moreover ensure that the flexible
7. ecommend verifying that the plug is properly inserted in the power socket and that the gas flows normally to the hob Should you fail to identify the cause of the malfunction switch off the appliance do not tamper with it and contact the Technical Assistance Service The appliance comes with a warranty certificate that enables the owner to benefit from the Technical Assistance Service The warranty certificate must be stored and duly filled in to be presented to the Technical Assistance Service whenever required together with a fiscally valid document issued by the dealer at the moment of purchase delivery note invoice tax receipt other and indicating the dealer s name delivery date product identification data and purchase price 12
8. he hob to the cabinet The hob is secured to the cabinet with the aid of clamps supplied as accessories The underside of the hob contains pre drilled holes through which the self tapping plates A must be inserted the relative screws C that secure the fixing clamps B must then be screwed onto the plates Applying the sealant Important the picture below indicates how the sealant must be applied along the entire edge This appliance is designed for non professional use in domestic environments Installation room The use of a gas cooker hob generates heat and humidity in the room in which it is installed Make sure the room is well ventilated by keeping any natural ventilation openings open or by installing a cooker hood with flue duct Fig 1 2 Intensive and prolonged use of the appliance may require additional ventilation either by opening a window or by increasing the efficiency and power of the mechanical ventilation system if present An electric ventilator must be implemented if a cooker hood Fig 2 cannot be installed it must be fitted to the external wall or window in the room Fig 3 provided the room is equipped with air intake vents The electric ventilator must guarantee an hourly air exchange rate 3 5 times the volume of the kitchen The installer must comply with the specifications of the UNI CIG 7129 and 7131 standards currently in force Fig 1 Electrical connection Check the data on the rating
9. plate located on the underside of the appliance and verify that the rated voltage complies with the mains voltage Check the efficiency of the earthing system before carrying out the electrical connection It is mandatory to earth the appliance The Manufacturer shall not be held liable for any harm to persons or damage to objects arising from failure to comply with this provision If the model is not equipped with a plug install a standardised plug on the cable that is capable of withstanding the power Output indicated on the rating plate The earth wire is identified by the yellow green jacket The plug must always be accessible When carrying out a fixed connection to the mains electricity an omnipolar cut off device with a contact gap of at least 3 mm must be installed between the appliance and the power outlet In order to connect the cord to the cooker hob loosen and remove the terminal board cover to access the contacts located inside After making the connection secure the cord with the fixing system provided and cover the terminal board immediately Whenever the power cord is replaced make sure that the earth wire yellow green is 10 mm longer than the remaining wires Use an HO5RR F type rubber cord comprising wires with 3x1 5 mm cross section 9 DECLARATION OF CONFORMITY Regarding the components intended to come into contact with foodstuffs this appliance conforms to the specifications of Italian Legislative Decree no 108 dated
Download Pdf Manuals
Related Search