Chief RPA293 project mount
Contents
1. o Figure 3 5 Proceed to Installing Projector with Interface Bracket section Installing to Threaded Rod NOTE The RPA projector mount may be suspended from four 1 4 20 steel threaded rods not included which are secured to unistrut by 1 4 20 Grade 2 or better channel nuts not included or to angle or channel assembly overhead structural members trusses or l beams by 1 4 20 Grade 2 or better jam nuts not included Threaded rods must have 16 threads per square inch 1 Secure one end of each of the four threaded rods not included to the structural member 2 Install one 1 4 20 jam nut not included and one 1 4 washer not included onto each threaded rod 3 Install RPA onto threaded rods inserting the rods into the four slots on top of the RPA NOTE Hole in the RPA allows socket wrench access without unit disassembly 4 Secure the threaded rods to the RPA with one 1 4 20 jam nut not included and one 1 4 washer not included on each threaded rod See Figure 4 p Secure to unistrut using channel nuts not included Secure to angle or channel assembly using jam nuts not included Threaded rods Secure with jam nuts and washers not included Figure 4 5 Proceed to Installing Projector with Interface Bracket section PROJECTOR INSTALLATION IMPORTANT Model RPA uses optional Chief SLB Series interfa2. double 2 x 4 wood joist with a maximum drywall covering of 5 8 or suspended from four 1 4 20 Grade ASTM A307 or better threaded rods not included which are secured to unistrut by 1 4 20 Grade 2 or better channel nuts not included or to angle or channel assembly overhead structural members trusses or l beams by 1 4 20 Grade 2 or better jam nuts not included NOTE RPA Series may be used with Listed Chief models WM110S WM120S WM130S WM210S WM220S WM230S WM240S WM210SI WM220SI WM230SI WM240Sl CMA151 and LSB100 not included SAVE THESE INSTRUCTIONS 1 03 75 a NEE BOLTCIRCLE DIMENSIONS INCHES ACCESSHOLE 75 NOTE CUSTOM INTERFAC E NOT SHOWN THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR PROJ ECTOR WILL ADD DEPTH TO INTALLATIO N AND WILLAFFECT LOCATION OF PROJECTOR ON MOUNT SEE SLB XXXX DRAWING ALSO 2 Installation Instructions RPA Series LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar
3. fixador Allentare il fissaggio 0 Bevestiging losdraaien Desserrez les fixations Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella CO 2 y Kruiskopschroevendraaier Tournevis pointe cruciforme Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Open Ended Wrench Llave de boca Gabelschl ssel A Q Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Socket Wrench Cl douilles Steckschl ssel Chave de caixa Chiave a brugola Dopsleutel Cl douilles TOOLS REQUIRED FOR INSTALLATION PARTS Hardware required not included dependent on installation method d Install to threaded extension column 1 1 2 or NPSM following ANSI ASME B1 20 1 Schedule 40 0 154 minimum thickness steel or aluminum ASTM B221 threaded extension column not included i 7 6 1 8 wood Install to wood ceiling joists Qty of 4 each e 1 4 x2 minimum length Grade 2 lag bolts 1
4. 4 Grade 2 nuts 1 4 Grade 2 washers 3 Install to threaded rod UAG 1 4 20 steel threaded rods Qty 4 2S e 1 4 20 Grade 2 channel nuts Qty 4 1 4 20 Grade 2 jam nuts Qty 8 e 1 4 Grade 2 washers Qty 8 WW M amp Example of SLB bracket RPA Series Installation Instructions PREPARATION Locate Mounting Site WARNING IMPROPER INSTALLATION MAY LEAD TO PROJECTOR MOUNT FALLING CAUSING SEVERE PERSONAL INJURY OR DAMAGE TO EQUIPMENT It is the installers responsibility to make certain the structure to which the projector mount is being mounted is capable of supporting five times the weight of the projector mount and all attached equipment Reinforce the structure as required before installing the projector mount 1 Determine required position of the RPA projector mount 2 Determine required distance of the projector mount from the screen using the lens to screen distance information NOTE Proceed to Installing to 1 1 2 Threaded Extension Column Installing to Wood Framework Joists or Installing to Threaded Rod section as appropriate INSTALLATION Installing to 1 1 2 Threaded Extension Column 1 Install 1 1 2 NPT or NPSM following ANSI ASME B1 20 1 Schedule 40 0 154 minimum thickness steel or aluminum ASTM B221 threaded extension column not included into threaded collar until tight with a minimum of four threads engaged 2 Thread RPA projector mount A onto th
5. INSTALLATION INSTRUCTIONS Projector Mount S CHIEF RPA Series Our Mounts Your RPA Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to mak
6. TS The RPA projector mount can be adjusted for pitch vertical elevation roll horizontal tilt and yaw rotation WARNING OVER LOOSENING OR REMOVAL OF HARDWARE MAY RESULT IN PERSONAL INJURY OR SERIOUS DAMAGE TO EQUIPMENT RPA projector mount and hardware is to be loosened only enough to allow for necessary movement Pitch Vertical Elevation Adjust pitch using the two pitch adjustment screws located on each end of the RPA 1 Loosen two pitch adjustment screws located on each end of the RPA 2 Adjust projector angle to desired pitch See Figure 7 3 Tighten two pitch adjustment screws located on each end of the RPA Figure 7 Roll Horizontal Tilt Adjust roll using the four roll adjustment screws two on front and two on the back of the RPA 4 Loosen two roll adjustment screws on each side of the RPA 5 Adjust projector to desired position See Figure 8 6 Tighten two roll adjustment screws on each side of the RPA Figure 8 Yaw Rotation Adjust yaw by threading or unthreading the RPA projector mount on the threaded extension column not included 7 Loosen set screw See Figure 9 WARNING IMPROPER ADJUSTMENT CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Do NOT unthread RPA to the end of pipe threads 8 Adjust projector by turning RPA projector mount on the extension column to the desired yaw position 9 Ti
7. ce brackets See Parts drawing 1 Attach projector to interface bracket B using installation instructions and hardware included with the interface bracket NOTE Security screws can be substituted when mounting interface bracket to projector by using the hardware and installation instructions in the All Points Security Kit included with interface bracket RPA Series Installation Instructions Installing Projector with Interface Bracket 1 Orient projector with interface bracket Mounting structure not shown for clarity 2 Loosen but do not remove thumb nuts on the interface bracket See Figure 5 3 Raise projector with attached interface bracket to RPA projector mount A See Figure 5 Mounting structure not shown for clarity Locating slots Figure 6 7 Route all cables as required Figure 5 4 Align the thumb nuts on the interface bracket with the locating slots on the RPA projector mount See Figure 6 5 Slide the interface bracket with attached projector to the limit of the locating slots See Figure 6 WARNING IMPROPER INSTALLATION CAN LEAD TO PROJECTOR FALLING RESULTING IN SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Make certain mounting slots in RPA projector mount base slide under thumb screws and that screws are seated in the back of locating slots 6 Tighten thumb nuts to secure projector in place Installation Instructions RPA Series ADJUSTMEN
8. e sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component DIMENSIONS WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the RPA does not exceed 50 Ibs 22 7 kg Theweight capacity of the RPA may be LIMITED to the lowest weight capacity of any other components located between the RPA and the supporting structure WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors IMPORTANT The RPA mounts are designed to be mounted to a 1 1 2 NPT or NPSM following ANSI ASME B1 20 1 Schedule 40 0 154 minimum thickness steel or aluminum ASTM B221 threaded extension column not included or mounted to a
9. e threaded extension column not included until hand tight with a minimum of four threads engaged 3 Turn RPA clockwise or counter clockwise until front of mount is facing target IMPORTANT When RPA is properly positioned the set screw access hole should be pointing directly at target or 180 AWAY from target 4 Secure RPA to pipe by turning set screw until tight See Figure 1 CAUTION DO NOT OVERTIGHTEN Over tightening of set screw can damage threads on pipe column not included Figure 1 5 Proceed to Installing Projector with Interface Bracket section Installing to Wood Framework Joists 1 Using the RPA as a guide mark four mounting hole locations See Figure 2 2 Drill four 1 8 x 1 1 2 deep minimum depth pilot holes See Figure 2 example only Figure 2 3 Align four mounting holes in RPA with four pilot holes Installation Instructions RPA Series IMPORTANT When RPA is properly positioned the set screw access hole should be pointing directly at target or 180 AWAY from target 4 Secure RPA to structure using four 1 4 x 2 minimum length lag bolts not included and four 1 4 flat washers not included See Figure 3 NOTE If the wood framework structure allows the hardware may be installed from above the RPA projector mount
10. ghten set screw Figure 9 RPA Series Installation Instructions USA International G CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002417 Rev01 2014 Milestone AV Technologies www chiefmfg com 05 14 gt TI U 6436 Citv West Parkwav Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
Download Pdf Manuals
Related Search