Philips AVENT SCD603
Contents
1. 5 11 Reset feature This feature allows you to reset the settings of parent unit You can use this function if problems occur that you cannot solve by following the suggestions in chapter Frequently asked questions KN Press and hold the on off button on the parent unit to switch it off H Press and hold the volume down button and simultaneously press and hold the on off button until a beep is heard and the parent unit switches on again The parent unit has now been reset to default factory settings 5 11 1 Default settings Loudspeaker volume 3 Voice activation off e Display brightness 4 T u Lu 6 Cleaning and maintenance A Warning Do not immerse the parent unit and the baby unit in water and do not clean them under the tap A Warning Do not use a cleaning spray or liquid cleaners KN Switch off the baby unit and the parent unit and remove the adapters from the wall socket FA Clean the parent unit and the baby unit with a dry cloth 6 Note Fingerprints or dirt on the lens of the baby unit may affect the camera s performance Avoid touching the lens with your fingers A Warning Make sure the baby unit and parent unit are dry before you connect them to the mains again E Clean the adapters with a dry cloth 7 Storage When you are not going to use the baby monitor for some time remove the non rechargeable batteries from the baby unit and the rechargeable ba2. Always here to help you Register your product and get support at www philips com welcome SCD603 Question Contact Philips PHILIPS AVERIT EQ Table of contents 1 Introduction 3 2 General description 3 3 Preparing for use 4 4 Using the appliance 6 5 Features 8 6 Cleaning and maintenance 12 7 Storage 12 8 Ordering accessories 12 9 Guarantee and service 12 10 Frequently asked questions 12 1 Introduction Congratulations on your purchase and welcome to Philips AVENT To fully benefit from the support that Philips AVENT offers register your product at www philips com welcome The Philips AVENT video monitor provides you with round the clock support and it allows you to see your baby day and night from anywhere in the house The latest digital technology guarantees clear sound and the clearest image of your baby This gives you an additional sense of security without entering your baby s room and disturbing its sleep 2 General description Parent unit Antenna Battery power on light Voice activation light Brightness adjustment buttons Video display icon explanation e a Parent unit and baby unit are not linked e b Battery status c Signal strength symbol d Volume level bar e e Brightness level bar e f Lullaby numbers e g Repeat lullaby symbol
3. h Voice activation symbol e i Volume muted symbol Volume up and down buttons Sound level lights Socket for appliance plug 9 Loudspeaker 10 Battery compartment lid 11 Belt clip stand 12 On off button 13 Voice activation button 14 Lullaby play stop button 15 Next lullaby button 16 Rechargeable battery 17 Adapter 18 Appliance plug I Baby unit 1 Antenna U1 amp N O ightlight and nightlight button Wall mounting holes 9 Battery compartment lid 10 Socket for appliance plug 11 On off switch 12 Appliance plug 13 Adapter 2 Poweron light 3 icrophone 4 Lens 5 Loudspeaker 6 Base gt 8 z wn uw 3 Preparing for use IMPORTANT Read the important safety instructions carefully before you use the video baby monitor and keep them for future reference Hereby Philips Electronics UK Limited declares that this Baby Monitor is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC A copy of the EC Declaration of Conformity DoC is available on CDROM or from website www philips com support 3 1 Baby unit Use the baby unit from the mains To guarantee automatic power backup in case of mains failure we advise you to insert non rechargeable batteries 3 1 1 Mains operation EN Put the appliance plug in the baby unit and put the adapter in a wall socket 3 1 2 Placing the non recharge
4. 490 feet in open air and line of sight Indoors the operating range is up to 30 metres 98 feet Depending on the surroundings and other disturbing factors this range may be smaller For wet and moist materials the range loss may be up to 100 Dry materials Material Loss of thickness range Wood plaster cardboard lt 30cm 0 10 glass without metal 12in wires or lead Brick plywood lt 30cm 5 35 12in Reinforced concrete lt 30cm 30 100 12in etal grilles or bars lt 1cm 90 100 0 4in etal or aluminium lt 1cm 100 sheets 0 4in 5 Features 5 1 Adjusting loudspeaker volume You can adjust the loudspeaker volume of the parent unit to the level you prefer KN Press the volume up or down button to adjust the volume JE The volume bar appears on the display to show the selected volume fi AV apy 62 S 6 Note f the volume is set to a high level the parent unit consumes more power 5 2 Adjusting display brightness You can adjust the display brightness of the parent unit to the level you prefer KN Press the brightness adjustment buttons on the parent unit to adjust the brightness of the video display The display brightness bar appears on the display to show the selected display brightness PHILPS A Ver 6 Note If the brightness is set to a high level the parent unit consumes m
5. 5 metres 3 5 to 5 feet away from the baby Why isn t the image on the video display clear in night vision e The distance between the baby and the baby unit may be too large Make sure that the baby unit is placed 1 to 1 5 metres 3 5 to 5 feet away from the baby Sometimes it is possible to see a greenish image when the infrared lights are on This is normal due to external factors www philips com AVENT Philips Consumer Lifestyle BV Tussendiepen 4 9206 AD Drachten Netherlands Trademarks owned by the Philips Group 2014 Koninklijke Philips N V AIl rights reserved www philips com 4222 005 0391 4
6. your baby Make sure the baby unit is not further than 1 5 metres 5 feet from your baby but not closer than 1 metre 3 5 feet to avoid a strangulation hazard 72 Why does the parent unit react too quickly to other sounds e The baby unit also picks up other sounds than those of your baby Move the baby unit closer to the baby but observe the minimum distance of 1 metre 3 5 feet Why does the parent unit make a buzzing sound Interference may occur when the parent unit is out of range of the baby unit Interference may also occur if there are too many walls or ceilings between the parent unit and the baby unit or when other 2 4GHz wireless devices are switched on e g microwave Wi Fi router Put the parent unit in a different place closer to the baby unit or switch off other wireless devices The rechargeable battery of the parent unit may need to be charged Operating time operating range The specified operating range of the baby monitor is up to 150 metres 490 feet outdoors and up to 30 metres 98 feet indoors Why does my baby monitor manage a much smaller distance than that e The specified operating range of 150 metres 490 feet is only valid outdoors in open air and in the line of sight Depending on the surroundings and other disturbing factors the operating range may be smaller Inside your house the operating range Is limited by the number and type of walls and or ceiling
7. Insert the appliance plug into the parent unit and put the adapter in a wall socket Then press and hold he on off button to switch on the parent unit and to establish connection with the baby unit Perhaps the baby unit is not connected to the mains and the non rechargeable batteries in he baby unit are empty or there are no non rechargeable batteries in the baby unit at all Connect the baby unit to the mains or put new non rechargeable batteries in the baby unit Then set the on off switch of the baby unit to ON position to establish connection with the parent unit Why doesn t the parent unit charge when plug it in The rechargeable battery may have reached the end of its life Replace the rechargeable battery Perhaps the adapter is not plugged in properly Make sure the adapter is plugged into the wall socket properly Why doesn t the baby unit charge when plug it in e The baby unit does not have a charging function Put new non rechargeable batteries in the baby unit if you want to use the baby unit cordlessly Why can t establish a connection Why is the connection lost every now and then Why are there sound interruptions e The baby unit and the parent unit are probably close to the outer limits of the operating range or there is interference from other 2 4GHz wireless devices Try a different location decrease the distance between the units or switch off other 2 4GHz wireless devices Plea
8. able batteries n case of mains failure the baby unit can run on four 1 5V R6 AAA alkaline batteries not included Do not use rechargeable batteries The baby unit does not have a charging function and rechargeable batteries discharge slowly when they are not in use A Warning Unplug the baby unit and make sure your hands and the unit are dry when you insert non rechargeable batteries 6 Note The baby unit has an operating time of 3 hours when you use it on non rechargeable alkaline batteries with the night light switched on EN Remove the battery compartment lid 6 Note Make sure the and poles point in the right direction EJ Reattach the lid 3 2 Parent unit 3 2 1 Operation on rechargeable battery A Warning Unplug the parent unit and make sure your hands and the unit are dry when you insert the rechargeable battery The parent unit comes with a rechargeable Li ion polymer 1100mAh battery Charge the parent unit before you use it for the first time or when the parent unit indicates that the battery is low The battery is low when the empty battery symbol flashes on the video display and the battery power on light on the parent unit flashes red PHILIPS AVENT 6 Note f the battery is completely empty the parent unit automatically switches off and loses contact with he baby unit KN Slide down the batte
9. aby unit or when other 2 4GHz wireless devices are switched on e g microwave Wi Fi router Put the parent unit in a different place closer to the baby unit or switch off other wireless devices Output video display Why does the video display flicker e Interference may occur when the parent unit is out of range of the baby unit Interference may also occur if there are too many walls or ceilings between the parent unit and the baby unit or when other 2 4GHz wireless devices are switched on e g microwave Wi Fi router Put the parent unit in a different place closer to the baby unit or switch off other wireless devices e The rechargeable battery of the parent unit may need to be charged Why isn t there any image on the video display when the battery power on light is on e The parent unit may be in the voice activation mode Press the voice activation button again to switch on the video display Why isn t the image on the video display clear The display brightness may be set too low Increase the display brightness see chapter Features section Adjusting display brightness Perhaps you did not remove the protective foil from the video display Remove the protective foil Why doesn t the parent unit work in the voice activation mode e The distance between the baby and the baby unit may be too large to pick up sounds from the baby Make sure that the baby unit is placed 1 to 1
10. belt clip as a stand turn it downwards until the parent unit can rest on it 5 7 Out of range alert When the parent unit is out of range of the baby unit the parent unit beeps every 20 seconds and the out of range image appears on the video display 6 Note The out of range alert is also active when the baby unit is switched off 5 8 Night vision The camera has infrared lights that allow you to see your baby clearly even in a dark room When the camera detects low light levels the infrared lights are switched on automatically Place the baby unit 1 to 1 5 metres 3 5 to 5 feet away from the baby to ensure a clear view 6 Note The display is black and white when the infrared lights are on However sometimes it is possible to see a greenish image This is normal due to external light sources 5 9 Belt clip stand e If the rechargeable battery of the parent unit is sufficiently charged you can take the unit with you inside and outside the house by attaching the unit to your belt or waistband with the belt clip This allows you to monitor your baby while you are moving around L 5 10 Auto mute feature When the baby unit detects a low sound level e g the sleeping sound of the baby the parent unit automatically mutes the sound output so that you will not hear this sound When the baby starts to cry the parent unit automatically switches on the volume again to let you hear the crying sound
11. ery gradually discharges even when the parent unit is switched off 6 Note We advise you to use the parent unit connected to the mains during the whole night If the parent unit runs out of battery the low battery alert beeps and this may wake you up 4 Using the appliance KEN Place the parent unit and the baby unit in the same room to test the connection Make sure the baby unit is at least 1 5 metres 5 feet away from the parent unit E Set the on off switch on the baby unit to the ON position The green power on light goes on 6 Note The power on light always lights up green even when there is no connection with the parent unit E Press and hold the on off button on the parent unit e The video display goes on and the linking image appears on the display e When a connection has been established the baby is shown on the video display and the signal strength symbol appears 4 1 Positioning the baby monitor O Warning Keep the baby unit out of the reach of the baby Never place the baby unit inside or mount it on the baby s bed or playpen 6 Note If you use a cordless phone wireless video Wi Fi network microwave oven or Bluetooth on 2 4Ghz and you experience interference on either the parent unit or baby unit move the parent unit further away until there is no more interference KN For optimal so
12. ore power 5 3 Sound level lights The parent unit continuously monitors the sound level in your baby s room and the sound level lights let you know if there is any activity If your baby cries the blue sound level lights light up on the parent unit As long as no sound is detected the sound level lights are out e When the baby unit picks up a sound one or more sound level lights on the parent unit go on The number of lights that go on depends on the loudness of the sound picked up by the baby unit The sound level lights also go on when the parent unit is set to a low volume or when the voice activation mode is activated see section Voice activation below PHILIPS AVENT 5 4 Voice activation The parent unit continuously monitors the sound level in your baby s room When the voice activation mode is activated the video display only switches on when the baby unit picks up a sound As long as no sound is detected the video display is off to save power KN To activate the voice activation mode press the voice activation button on the parent unit e The voice activation light on the parent unit goes on and the voice activation image appears on the video display e When the baby unit detects a sound the video display on the parent unit automatically goes on to show the baby When no new sound is detected for 20 seconds the video display goes ou
13. r Preparing for use e The baby unit may be switched off Switch on the baby unit Noise sound Why does the video monitor produce a high pitched noise The units may be too close to each other Make sure the parent unit and the baby unit are at least 1 5 metres 5 feet away from each other and set the volume to a lower level e The volume of the parent unit may be set too high Decrease the volume of the parent unit Can increase the volume of the lullaby on the baby unit e No you can t Why don t hear a sound Why can t hear my baby cry e The volume of the parent unit may be set too low or may be switched off Press the volume up button to increase the volume level Perhaps you did not remove the protective foil from the microphone Make sure all protective foil has been removed Perhaps you have switched on the voice activation If the voice activation is activated the video display only switches on when the baby unit picks up a sound As long as no sound is detected the video display is off to save power Perhaps the video baby monitor is in auto mute When the baby unit detects a low sound level e g the sleeping sound of the baby the parent unit automatically mutes the sound output so that you do not hear this sound When the baby starts to cry the parent unit automatically switches on the volume again to let you hear the crying sound e The baby unit may be too far away from
14. ry compartment lid to remove it B Insert the rechargeable battery 6 Note Make sure the and poles point in the right direction EJ Reattach the lid EJ Insert the appliance plug into the parent unit and put the adapter in a wall socket e The battery power on light on the parent unit lights up green The animated battery charging image appears at the top of the video display PHILIPS AVENT When the battery is fully charged the battery symbol at the top of the video display is full When you charge the parent unit for the first time or after a long period of disuse switch it off and let it charge continuously for at least 4 hours e Charging normally takes 2 5 hours but it takes longer when the parent unit is switched on during charging To keep the charging time as short as possible switch off the parent unit during charging When the rechargeable battery is fully charged the parent unit can be used cordlessly for approx 7 hours if it is in voice activation mode If the video display is on continuously the parent unit can be used cordlessly at default setting for approx 5 5 hours 6 Note When the parent unit is charged for the first time the operating time is less than 7 hours The rechargeable battery only reaches its full capacity after four discharging and charging cycles 6 Note The batt
15. s between the parent unit and the baby unit The operating time of the parent unit is supposed to be at least 5 5 hours Why is the operating time of my parent unit shorter e When the parent unit has been charged for the first time the operating time is shorter because he battery has not reached its full capacity yet The rechargeable battery only reaches its full capacity after four discharging and charging cycles After this the operating time is 5 5 hours if the voice activation is not deactivated and 7 hours if the voice activation mode is activated The parent unit consumes a lot of energy when he video display is switched on continuously Activate the voice activation mode to increase he operating time see chapter Features section Voice activation e The volume of the parent unit may be set too high which causes the parent unit to consume a lot of energy Decrease the volume of the parent unit As any other rechargeable electronic device the battery capacity decreases after a long period of usage If you have any questions you can always contact consumer care To purchase a new rechargeable battery visit our Philips online shop www shop philips com service Why do get interference on the parent unit e Interference may occur when the parent unit is out of range of the baby unit Interference may also occur if there are too many walls or ceilings between the parent unit and the b
16. se note that it takes about 5 seconds each time before a connection between the units is re established e If you have two video baby monitors keep hem at least 1 5 metres 5 feet away from each other to prevent interference Perhaps the baby unit is not connected to the mains and the non rechargeable batteries in he baby unit are empty or there are no non rechargeable batteries in the baby unit at all Connect the baby unit to the mains or put new non rechargeable batteries in the baby unit Then set the on off switch of the baby unit to ON position to establish connection with the parent unit What happens during a power failure As the parent unit works on a rechargeable battery it continues to work if the battery is sufficiently charged If you have placed non rechargeable batteries in the baby unit the camera continues to work and you can see your baby Why do the non rechargeable batteries of the baby unit run low quickly The baby unit consumes a lot of energy when you have the video display switched on continuously when you play lullabies or when the nightlight is switched on We recommend to always use the baby unit from the mains and use the batteries for back up purpose only Do not place rechargeable batteries in the baby unit as they discharge slowly even when they are not in use aE A a G ENC Why does the charging time of the parent unit exceed 2 5 hours e The parent
17. t again FA To deactivate the voice activation mode press the voice activation button on the parent unit again The voice activation light goes out and the voice activation off image appears on the display 5 5 Nightlight KN Press the nightlight button on the base of the baby unit to switch on the nightlight The nightlight on the base of the baby unit goes on E Press the nightlight button again to switch off the nightlight 5 6 Lullaby function KN Press the lullaby play stop button on the parent unit to play a lullaby e The lullaby starts to play on the baby unit and is repeated continuously for approx 15 minutes On the video display you see which lullaby number is played and repeated This number is shown in a blue square A To select another lullaby press the lullaby button Continue pressing the next lullaby button until you hear the lullaby you prefer 6 Note You can also select the repeat symbol to play all lullabies repeatedly in a loop E Press the lullaby play stop button on the parent unit to play the lullaby selected e The lullaby starts to play on the baby unit and is repeated continuously 6 Note If you have selected the repeat mode all three lullabies are played repeatedly in a loop EJ To stop the lullaby press the lullaby play stop button again e To use the
18. ttery from the parent unit Store the parent unit the baby unit and the adapters in a cool and dry place 8 Ordering accessories To purchase accessories for this appliance please visit our online shop at www shop philips com service f the online shop is not available in your country go to your Philips dealer or a Philips service centre If you have any difficulties obtaining accessories for your appliance please contact the Philips Consumer Care Centre in your country You find its contact details in the worldwide guarantee leaflet 9 Guarantee and service If you need service or information or if you have a problem please visit the Philips AVENT website at www philips com AVENT or contact the Philips Consumer Care Centre in your country You find its phone number in the worldwide guarantee leaflet If there is no Consumer Care Centre in your country go to your local Philips dealer 10 Frequently asked questions This chapter lists the questions most frequently asked about the appliance If you cannot find the answer to your question visit www philips com support for more frequently asked questions or contact the Consumer Care Centre in your country Switching on connecting the units Why don t the power on light of the baby unit and the parent unit go on when switch on the units Perhaps the rechargeable battery of the parent unit is empty and the parent unit is not connected to the mains
19. und detection place the baby unit at least 1 metre 3 5 feet away from your baby but no further than 1 5 metres 5 feet away Tip Find out what the best position is for the parent unit by looking at the signal strength symbol The number of stripes indicates the quality of the connection If no connection can be established the parent unit beeps and the out of range image appears on the display EI There are two ways to position the baby unit 1 Place the baby unit on a stable level and horizontal surface 2 Mount the baby unit to the wall as shown in the figure with the screws supplied Tip Use the provided template to mark the exact location of the screw holes on the wall Tip Position the baby unit at a higher level to get a good overview of the baby s bed or playpen Adjust the baby unit in a way that ensures the best visibility of your baby A Warning Do not position the baby unit with the microphone pointing too far down as this may prevent the microphone from picking up sounds properly Place the parent unit within the operating range of the baby unit Make sure it is at least 1 5 metres 5 feet away from the baby unit to avoid acoustic feedback For more information on the operating range see section Operating range below 4 1 1 Operating range The operating range of the baby monitor is 150 metres
20. unit may be switched on during charging Switch off the parent unit during charging Why do need to keep the baby unit and its cord at least 1 metre 3 5 feet from my baby To avoid strangulation with the cord and for optimal sound detection always place the baby unit and its cord at least 1 metre 3 5 feet away from the baby Indications on the parent unit Why doesn t the battery status symbol appear on the video display of the parent unit when start to charge the parent unit It may take a few minutes before the battery symbol appears on the video display of the parent unit when you charge the parent for the first time or after a long period of disuse Why do the battery power on light and the battery symbol on the video display flash red If the battery power on light and the battery symbol on the video display flash redithe rechargeable battery of the parent unit is low Connect the parent unit to the mains to recharge the battery see chapter Preparing for use Why does the parent unit beep e f the parent unit beeps while the out of range image appears on the video display the connection with the baby unit is lost Move the parent unit closer to the baby unit e lf the parent unit beeps while the battery power on light and the battery symbol on the video display flash red the rechargeable battery of the parent unit is low Connect the parent unit to the mains to recharge the battery see chapte
Download Pdf Manuals
Related Search