Home

Havis C-DMM-114 car kit

1. into cavity bracket Replace cover trim bezel and reattach gas Radio will fit over four 4 mounting studs shock stud Secure radio to studs with existing 8 32 nuts Rubber Bumpers are provided to push against the top OEM trim bezel and the back side of the metal cavity bracket This is needed because the top OEM clip holes are covered hv the new hracket Reattach cover trim bezel with screws previously removed RENN T Attach C MM 200 series bracket to the back of monitor Place monitor mount into desired position of swivel Note Some computers require wiring to be connected bracket and attach with 1 4 serrated nuts prior to attaching adaptor bracket CDM Mele Nel 410 rev 2 13 uant Run monitor wire harness on exterior of dash as desired Ay Dash Monitor Mount with console installation complete SS C DMM 114_INST_4 10 rev 9 13
2. Havis Inc 75 Jacksonville Road PO Box 2099 Warminster PA 18974 HAVI S T 800 524 9900 F 215 957 0729 Productivity in motion www havis com INSTALL INSTRUCTIONS C DMM 114 2007 2014 TAHOE SWING OUT DASH MONITOR MOUNT The Dash Monitor Mount bracket system requires two or three main parts that are Sold Separately See web site Monitor Configurator for more detailed bracket information http www havis com monitor_mounts htm e 1 Vehicle Specific dash mount bracket C DMM 114 e Computer Specific Monitor adaptor bracket C MM 200 series e 1 Offset adaptor bracket C MM 301 The C MM 301 offset adaptor goes between the C DMM 114 and C MM 2XX It may not be required in some applications TOOLS REQUIRED e Ratchet Wrench e Socket Set e Open End Wrenches 7 16 1 2 e Phillips Screwdriver short HARDWARE QTY DESCRIPTION PART 2 1 4 x 3 4 Hex Bolt GSM33001 2 1 4 Flat Washer GSM3 1005 2 1 4 Nylon retaining washer GSM31322 6 1 4 20 Hex Flange Serrated Nut GSM30023 4 10 32 x 1 2 Flat Head Machine Screw GSM33072 4 Rubber Bumpers stick on GSM19802 1 Monitor Adapter Hardware Varies monitor specific ALWAYS e Read all instructions before installing any Havis Inc products e Use hardware provided with install kit Note The swing door utilizes a gas spring to assist in opening the door and to eliminate the possibility of it slamming shut If additional damping is desired because of h
3. eavier equipment an optional stronger gas spring is available under Part Number CM86662 30 sold separately Installer must change out gas spring as needed C DMM 114 Assembly for Tahoe C MM 301 _ _ _ gt Offset Adaptor C MM 201 i Monitor Mount Adaptor v ae a VESA bracket shown Le C DMM 114_INST_4 10 rev 9 13 Installation at amp og a AAA PF OEM Dash Carefully remove center OEM trim bezel Prior to installation This has eight 8 snap in clips Remove 4 screws that hold radio head Screws to be reused 7 mm socket Disassemble Attach 1 Side support brackets onto original radio 1 Side support brackets mount holes with OEM screws 2 Cover Trim Bezel One bracket onnesich sde 9 13 3 Gas Shock one end only Side support shown with OEM bezel back in place J Insert main bracket assembly into dash Attach main bracket to the side support cavity brackets with 10 32 x 1 2 screws provided Insert two 2 14 x 34 hex bolts and 4 washers into OEM existing holes from the forward side and hold bolts in place with nylon Main cavity bracket assembly installed retaining washers C DMM 114_INST_4 10 rev 9 13 This should be done prior to inserting cavity bracket With Cavity bracket in place attach 4 serrated nuts onto bolts Tighten hardware Attach wires into radio and insert

Havis C-DMM-114 car kit

Contents

Download Pdf Manuals

Related Search

Related Contents