Gigabyte GA-J1900N-D2H (rev. 1.1)
Contents
1. Enabled All PS 2 devices are functional in the operating system and during the POST Default This item is configurable only when Fast Boot is set to Enabled NetWork Stack Driver Support Disabled Disables booting from the network Default gt Enabled Enables booting from the network This item is configurable only when Fast Boot is set to Enabled Boot Option 1 2 3 Specifies the overall boot order from the available devices For example you can set hard drive as the first priority Boot Option 1 and DVD ROM drive as the second priority Boot Option 2 The list only displays the device with the highest priority for a specific type For example only hard drive defined as the first priority on the Hard Drive BBS Priorities submenu will be presented here Removable storage devices that support GPT format will be prefixed with UEFI string on the boot device list To boot from an operating system that supports GPT partitioning select the device prefixed with UEFI string Or if you want to install an operating system that supports GPT partitioning such as Windows 7 64 bit select the optical drive that contains the Windows 7 64 bit installation disk and is prefixed with UEFI string Hard Drive CD DVD ROM Drive Floppy Drive Network Device BBS Priorities Specifies the boot order for a specific device type such as hard drives optical drives floppy disk drives and devices that support Boot from LAN function etc2. gs Expansion Slots 1 x PCI Express x1 slot 1 x Mini PCI Express x1 slot This socket does not support USB Bluetooth signals The PCI Express x1 slots conform to PCI Express 2 0 standard Storage Interface SoC 2x SATA 3Gb s connectors K USB SoC 1 x USB 3 0 2 0 port on the back panel SoC GL850S USB 2 0 Hub 6xUSB 2 0 1 1 ports 4 ports on the back panel 2 ports available through the internal USB header mas Internal ED Connectors 9 9 9 9 1 x 24 pin ATX main power connector 1 x 4 pin ATX 12V power connector 2 X SATA 3Gb s connectors 1 x USB 2 0 1 1 header 1 x CPU fan header x system fan header 1 x front panel header 1 x front panel audio header 1 x serial port header 1 x parallel port header 1 x S PDIF Out header Only for GA J1800N D2H Only for GA J1900N D2H Internal e 1xClear CMOS jumper Connectors e 1 x chassis intrusion header eS Back Panel e 1x PS 2 keyboard port 1 Connectors 1x PS 2 mouse port e 1x D Sub port 1xHDMI port 1x USB 3 0 2 0 port 4x USB 2 0 1 1 ports 1x RJ 45 port e 3x audio jacks Line In Line Out Mic In lO Controller iTE 1 0 Controller Chip Hardware System voltage detection Monitor e CPU System temperature detection CPU System fan speed detection CPU System fan speed control Whether the fan speed control function is supported will depend
3. NC No Pin CO co 4 o o01 3 c5 n5 Line Out L NC R e The front panel audio header supports HD audio by default Audio signals will be present on both of the front and back panel audio connections simultaneously e Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug For information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer 4 10 F_USB USB 2 0 1 1 Header The header conforms to USB 2 0 1 1 specification Each USB header can provide two USB ports via an optional USB bracket For purchasing the optional USB bracket please contact the local dealer Pin No Definition Pin No Definition 10 1 Power 5V 6 USB DY 2 Power 5V f GND 9 3 USB DX 8 GND 4 USB DY 9 No Pin 5 USB DX 10 NC Do not plug the IEEE 1394 bracket 2x5 pin cable into the USB 2 0 1 1 header Prior to installing the USB bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket 11 SPDIF O S PDIF Out Header This header supports digital S PDIF Out and connects a S PDIF digital audio cable provided by expansion cards for sound car digital audio output from your motherboard to certain expansion cards like graphics cards and ds For example some gra
4. COM 12 BAT 6 LPT 13 CLR CMOS T SATA2 0 1 14 CI A Read the following guidelines before connecting external devices e First make sure your devices are compliant with the connectors you wish to connect e Before installing the devices be sure to turn off the devices and your computer Unplug the power cord from the power outlet to prevent damage to the devices e After installing the device and before turning on the computer make sure the device cable has been securely attached to the connector on the motherboard 11 1 2 ATX_12V ATX 2x2 12V Power Connector and 2x12 Main Power Connector With the use ofthe power connector the power supply can supply enough stable power to all the components on the motherboard Before connecting the power connector first make sure the power supply is turned off and all devices are properly installed The power connector possesses a foolproof design Connect the power supply cable to the power connector in the correct orientation The 12V power connector mainly supplies power to the CPU If the 12V power connector is not connected the computer will not start lag ATX_12V ATX_12V ATX Pin No Definition Pin No Definition Pin No Definition 1 GND 1 3 3V 13 3 3V 2 GND 2 3 3V 14 12V 3 12V 3 GND 15 GND 4 12V 4 15V 16 PS ON soft On Off 5 GND 17 GND 6 5V 18 GND 7 GND 19 GND 8 Power Good 20 5V 9 5VSB stand by
5. The parts and components have been carefully selected to meet RoHS requirement Moreover we at GIGABYTE are continuing our efforts to develop products that do not use internationally banned toxic chemicals Waste Electrical amp Electronic Equipment WEEE Directive Statement GIGABYTE will fulfill the national laws as interpreted from the 2002 96 EC WEEE Waste Electrical and Electronic Equipment directive The WEEE Directive specifies the treatment collection recycling and disposal of electric and electronic devices and their components Under the Directive used equipment must be marked collected separately and disposed of properly WEEE Symbol Statement The symbol shown below is on the product or on its packaging which indicates that this product psa must not be disposed of with other waste Instead the device should be taken to the waste collection centers for activation of the treatment collection recycling and disposal procedure The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local government office your household waste disposal service or where you purchased the product for details of environmentally safe recycling When your electrical or electronic equ
6. BBS Priorities SM OE Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 16 1242 Copyright C 2013 American Megatrends Inc Setup Prompt Timeout Allows you to configure the number of seconds to stay in BIOS setup prompt screen Default 6 Bootup NumLock State Enables or disables Numlock feature on the numeric keypad of the keyboard after the POST Default On Full Screen LOGO Show Allows you to determine whether to display the GIGABYTE Logo at system startup Disabled skips the GIGABYTE Logo when the system starts up Default Enabled Fast Boot Enables or disables Fast Boot to shorten the OS boot process Default Disabled 25 VGA Support Allows you to select which type of operating system to boot gt gt Auto Enables legacy option ROM only gt gt EFI Driver Enables EFI option ROM Default This item is configurable only when Fast Boot is set to Enabled USB Support gt gt Disabled All USB devices are disabled before the OS boot process completes gt gt Full Initial All USB devices are functional in the operating system and during the POST gt gt Partial Initial Part of the USB devices are disabled before the OS boot process completes Default This item is configurable only when Fast Boot is set to Enabled PS2 Devices Support gt gt Disabled All PS 2 devices are disabled before the OS boot process completes
7. Press Enter on this item to enter the submenu that presents the devices of the same type that are connected This item is present only if at least one device for this type is installed 26 2 7 Save amp Exit Aptio Setup Utility Copyright C 2013 American Megatrends Inc Main Advanced Chipset Security Boot Save amp Exit Save Changes and Reset Discard Changes and Reset Restore Defaults Save as User Defaults Restore User Defaults Boot Override UEFI USB 2 0 USB Flash Drive 0 00 UEFI Built in EFI Shell Launch EFI Shell From filesystem service gt lt Select Screen T4 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 16 1242 Copyright C 2013 American Megatrends Inc Save Changes and Reset Press lt Enter gt on this item and select Yes This saves the changes to the CMOS and exits the BIOS Setup program Select No or press lt Esc gt to return to the BIOS Setup Main Menu Discard Changes and Reset Press lt Enter gt on this item and select Yes This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS Select No or press lt Esc gt to return to the BIOS Setup Main Menu Restore Defaults Press lt Enter gt on this item and select Yes to load the BIOS factory default settings The BIOS defaults settings help the system to operate in optimum state Always load the Optimized
8. direction If you are unable to insert the memory switch the direction Dual Channel Memory Configuration This motherboard provides two DDR3L memory sockets and supports Dual Channel Technology After the memory is installed the BIOS will automatically detect the specifications and capacity of the memory The two DDR3L memory sockets are divided into two channels and each channel has one memory socket as following Channel A SODIMM 1 Channel B SODIMM 2 Due to SoC limitations read the following guidelines before installing the memory in Dual Channel mode 1 If only one DDR3L memory module is to be installed be sure to install it in the SODIMM 1 socket and Dual Channel mode cannot be enabled if only one memory module is installed 2 When enabling Dual Channel mode with two memory modules it is recommended that memory of the same capacity brand speed and chips be used for optimum performance 1 4 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card A e Make sure the motherboard supports the expansion card Carefully read the manual that came with your expansion card Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage 1 5 Back Panel Connectors e PS 2 Keyboard Mouse Port Use the upper port green to connect a PS 2 mouse and the lower port purple to connect a PS 2 keyboar
9. on the cooler you install BIOS 1 x 64 Mbit flash Use of licensed AMI UEFI BIOS PnP 1 0a DMI 2 7 WfM 2 0 SM BIOS 2 7 ACPI 5 0 Unique Features Support for BIOS Support for Xpress Install Support for APP Center Available applications in APP Center may differ by motherboard model Supported functions of each application may also differ depending on motherboard specifications Support for ON OFF Charge 44 Bundled Norton Internet Security OEM version Software Intel Smart Connect Technology CO OJUENG Support for Windows 8 1 8 7 System Mini ITX Form Factor 17 0cm x 17 0cm fim Form Factor GIGABYTE reserves the right to make any changes to the product specifications and product related information without prior notice Please visit the Support amp Downloads Utility page on GIGABYTE s website to check the supported operating system s for the software listed in the Unique Features and Bundled Software columns 1 3 Installing the Memory Read the following guidelines before you begin to install the memory A e Make sure that the motherboard supports the memory It is recommended that memory of the same capacity brand speed and chips be used Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage e Memory modules have a foolproof design A memory module can be installed in only one
10. such as enabling disabling a specific USB port and support for certain features PCI Express Configuration This section provides you with configuration options for the PCI Express bus such as enabling disabling a specific PCI Express channel and speed configuration Audio Controller Enables or disables the onboard audio function Default Enabled If you wish to install a 3rd party add in audio card instead of using the onboard audio set this item to Disabled High Precision Timer Enables or disables High Precision Event Timer HPET in the operating system Default Enabled 209 c Restore AC Power Loss Determines the state of the system after the return of power from an AC power loss gt gt Power Off The system stays off upon the return of the AC power Default gt gt Power On The system is turned on upon the return of the AC power gt gt Last State The system returns to its last known awake state upon the return of the AC power gt Soft Off by PWR BTTN Configures the way to turn off the computer in MS DOS mode using the power button gt gt Instant Off Press the power button and then the system will be turned off instantly Default Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system If the power button is pressed for less than 4 seconds the system will enter suspend mode 2 5 Security Aptio Setup Utility Copyright C 2013 American Megatrends Inc Main Advanced Chipse
11. 1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit w Realtek PCle GBE Family Controller MAC 74 D4 35 1D 21 FF SIO Configuration ww Version 2 16 1242 Copyright C 2013 American Megatrends Inc Power Loading Enables or disables dummy load When the power supply is at low load a self protection will activate causing it to shutdown or fail If this occurs please set to Enabled Auto lets the BIOS automatically configure this setting Default Auto H W Monitor CPU Temperature DTS System Temperature Displays current CPU system temperature CPU System Fan Speed Displays current CPU system fan speed Vcore VCC3 12V VCC CPU_VAXG 3VDUAL DDR1_35VIO Displays the current system voltages Intel R Smart Connect Technology ISCT Support Enables or disables Intel Smart Connect Technology Default Disabled SIO Misc Functions ErP Determines whether to let the system consume least power in S5 shutdown state Default Disabled Note When this item is set to Enabled the following functions will become unavailable PME event wake up power on by mouse power on by keyboard and wake on LAN Case Open Displays the detection status of the chassis intrusion detection device attached to the motherboard Cl header If the system chassis cover is removed this field will show Open otherwise it will show Close To clear the chassis intrusion status record set Reset Case Open S
12. 5V 21 5V 10 12V 22 5V 11 12V Only for 2x12 pin 23 5V Only for 2x12 pin ATX ATX 12 3 3V Only for 2x12 pin 24 GND Only for 2x12 pin ATX ATX 3 4 CPU FAN SYS FAN Fan Headers The motherboard has a 3 pin CPU fan header CPU FAN and a 4 pin system fan header SYS FAN Most fan headers possess a foolproof insertion design When connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire The speed control function requires the use of a fan with fan speed control design For optimum heat dissipation it is recommended that a system fan be installed inside the chassis CPU FAN SYS FAN 1 Pin No Definition Pin No Definition H 1 GND 1 GND 2 Speed Control 2 Speed Control irl 3 Sense oven 3 Sense 4 VCC Be sure to connect fan cables to the fan headers to prevent your system from overheating Overheating may result in damage to the system may hang These fan headers are not configuration jumper blocks Do not place a jumper cap on the headers 5 COM Serial Port Header The COM header can provide one serial port via an optional COM port cable For purchasing the optional COM port cable please contact the local dealer Pin No Definition Pin No Definition o 1 NDCD 6 NDSR 1 BERRA 2 NSIN 7 NRTS 3 NSOUT 8 NCTS 4 NDTR 9 NRI 5 GND 10 No Pin 6 LPT Paralle
13. A Enables or disables the integrated SATA controllers Default Enabled SATA Mode Allows you to decide whether to configure the SATA controller integrated in the Chipset to AHCI mode This item is configurable only when Serial ATA SATA is set to Enabled IDE Mode Disables RAID for the SATA controllers and configures the SATA controllers to IDE mode gt gt AHCI Mode Configures the SATA controllers to AHCI mode Advanced Host Controller Interface AHCI is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug Default Serial ATA Port 0 Serial ATA Port 1 Enables or disables each SATA port This item is configurable only when Serial ATA SATA is enabled The area below displays the current status of each SATA port SATA Port0 HotPlug SATA Port1 HotPlug Enables or disable the hot plug capability for each SATA port Default Disabled Network Stack Configuration Network Stack Disables or enables booting from the network to install a GPT format OS such as installing the OS from the Windows Deployment Services server Default Disabled Ipv4 PXE Support Enables or disables IPv4 PXE Support This item is configurable only when Network Stack is enabled Ipv6 PXE Support Enables or disables IPv6 PXE Support This item is configurable only when Network Stack is enabled CSM Configuration CSM Support Enables or disables UEFI CSM Compati
14. Displays a list of connected USB mass storage devices This item appears only when a USB storage device is installed Realtek PCle GBE Family Controller This sub menu provides information on LAN configuration and related configuration options SIO Configuration This section provides information on the super I O chip and allows you to configure the serial port and parallel port 22 2 4 Chipset Aptio Setup Utility Copyright C 2013 American Megatrends Inc Main Advanced Security Boot Save amp Exit Realtek LAN Controller Enabled gt North Bridge gt South Bridge gt lt Select Screen T4 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 16 1242 Copyright C 2013 American Megatrends Inc Realtek LAN Controller Enables or disables the onboard LAN function Default Enabled If you wish to install a 3rd party add in network card instead of using the onboard LAN set this item to Disabled North Bridge This section provides information on the installed memory size and memory onboard graphics related configuration options Intel IGD Configuration This section provides onboard graphics related configuration options MAX TOLUD Allows you to configure the maximum TOLUD value Default Dynamic South Bridge USB Configuration This section provides you with configuration options for the USB controller
15. GA J1800N D2H GA J1900N D2H User s Manual Rev 1101 12ME J180D2H 1101R GA J1900N D2H 4 Declaration of Conformity DECLARATION OF CONFORMITY Md Importer Per FCC Part 2 Section 2 1077 a G B T Technology Trading GMbH Address Bullenkoppel 16 22047 Hamburg Germany C Declare that the product Product Type Motherboard Product Name GA J1800N D2H GA J1900N D2H conforms with the essential requirements of the following directives Address 17358 Railroad Street City of Industry CA 91748 Phone Fax No 626 854 9338 626 854 9326 Responsible Party Name G B T INC U S A X 2004 108 EC EMC Directive x Conduction amp Radiated Emissions EN 55022 2010 X Immunity EN 55024 2010 hereby declares that the product q Power line harmonics EN 61000 3 2 2006 A2 2009 Product Name Motherboard PX Power line flicker EN 61000 3 3 2008 Model Number GA J1 800N D2H GA J1900N D2H X 2006 95 EC LVD Directive Conforms to the following specifications X Safety EN60950 1 2006 A12 2011 FCC Part 15 Subpart B Section 15 107 a and Section 15 109 x 2011 65 EU RoHS Directive a Class B Digital Device X Restriction of use of certain This product does not contain any of the restricted Supplementary Information substances in electronic equipment substances listed in Annex Il in concentrations o This device complies with part 15 ofthe FCC Rules Operation is and applications banned by the
16. GA J1900N D2H motherboard MI Motherboard driver disk vI Two SATA cables vI User s Manual IV O Shield The box contents above are for reference only and the actual items shall depend on the product package you obtain The box contents are subject to change without notice Only for GA J1800N D2H Only for GA J1900N D2H GA J1800N D2H GA J1900N D2H Motherboard Block Diagram DDR3L 1333 MHz Dual Channel Memory 2 SATA 3Gbis LAN atesos L ES Intel J1800 0CD USB Hub ees Intel J1900 Soc PCle CLK Realtek 1 USB 3 0 2 0 100 MHz GbE LAN IS 2usB 2 01 1 PCI Express Bus 1x1 x1 LPC Bus COM iTE i PCI Express x1 Mini PCI Express x1 73 CODEC PS 2 KB Mouse De e 2 SOQO uu Be oo m 2 Oo Ww OW QA No oo e ca aa DANN Cc L amp B CX Oo s P c Only for GA J1800N D2H Only for GA J1900N D2H FB For detailed product information limitation s refer to 1 2 Product Specifications 5 Chapter1 Hardware Installation 1 1 Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge ESD Prior to installation carefully read the user s manual and follow these procedures Prior to installation make sure the chassis is suitable for the motherboard Prior to installation do not remove or break motherboard S N Serial Number sticker or warranty
17. TECHNOLOGY CO LTD Address No 6 Bao Chiang Road Hsin Tien Dist New Taipei City 231 Taiwan TEL 886 2 8912 4000 FAX 886 2 8912 4005 Tech and Non Tech Support Sales Marketing http ggts gigabyte com tw WEB address English http www gigabyte com WEB address Chinese http www gigabyte tw You may go to the GIGABYTE website select your language in the language list on the top right corner of the website e GIGABYTE Global Service System GIGABYTE Jr Global Technical Service To submit a technical or non technical Sales Marketing question please link to Welcome to GIGABYTE Service system If you are a P Serer plonso losin with your http ggts gigabyte com tw Then select your language to enter the system can simply enter E Mail address to login Po co pa Aa Francais Polski Espa ol 99
18. all Single Items to manually select the drivers you wish to install 28 Regulatory Statements Regulatory Notices This document must not be copied without our written permission and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose Contravention will be prosecuted We believe that the information contained herein was accurate in all respects atthe time of printing GIGABYTE cannot however assume any responsibility for errors or omissions in this text Also note that the information in this document is subject to change without notice and should not be construed as a commitment by GIGABYTE Our Commitment to Preserving the Environment In addition to high efficiency performance all GIGABYTE motherboards fulfill European Union regulations for RoHS Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment and WEEE Waste Electrical and Electronic Equipment environmental directives as well as most major worldwide safety requirements To prevent releases of harmful substances into the environment and to maximize the use of our natural resources GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your end of life product Restriction of Hazardous Substances RoHS Directive Statement GIGABYTE products have not intended to add and safe from hazardous substances Cd Pb Hg Cr 6 PBDE and PBB
19. anguage used by the BIOS and manually set the system time e System Language Selects the default language used by the BIOS e System Date Sets the system date The date format is week read only month date and year Use lt Tab gt to switch between the Month Date and Year fields and use the lt gt or lt gt key to set the desired value e System Time Sets the system time The time format is hour minute and second For example 1 p m is 13 0 0 Use lt Tab gt to switch between the Hour Minute and Second fields and use the lt gt or lt gt key to set the desired value e Access Level Displays the current access level depending on the type of password protection used If no password is set the default will display as Administrator The Administrator level allows you to make changes to all BIOS settings the User level only allows you to make changes to certain BIOS settings but not all 18 2 3 Advanced ww w v Aptio Setup Utility Copyright C 2013 American Megatrends Inc Advanced BEEKO o Security Boot Save amp Exit Power Loading Auto Hardware Monitor Intel R Smart Connect Technology SIO Misc Functions CPU Configuration PPM Configuration Thermal Configuration IDE Configuration Network Stack Configuration CSM Configuration USB Configuration gt gt gt gt gt gt gt gt gt gt Select Screen T4 Select Item Enter Select Change Opt F
20. ation one computer system can function as multiple virtual systems Default Enabled Power Technology Allows you to configure Intel power management features Default Energy Efficient PPM Configuration CPU C state Report Enables or disables support for CPU s power saving functions Default Enabled Enhanced C state Enables or disables Intel CPU Enhanced Halt C1E function a CPU power saving function in system halt state When enabled the CPU core frequency and voltage will be reduced during system halt state to decrease power consumption This item is configurable only when CPU C state Report is enabled Default Enabled Max CPU C state Allows you to determine the maximum C state that the CPU will support Options include C6 C1 default This item is configurable only when CPU C state Report is enabled Thermal Configuration DTS Enables or disables the CPU overheating protection function Default Disabled Critical Trip Point Allows you to set the CPU temperature threshold If the CPU temperature reaches this value the operating system will shut down the system This item is configurable only when DTS is enabled Default 100 C Passive Trip Point Allows you to set the CPU temperature threshold If the CPU temperature reaches this value the CPU frequency will be automatically reduced This item is configurable only when DTS is enabled Default 85 C 20 v v v IDE Configuration Serial ATA SAT
21. battery model When installing the battery note the orientation of the positive side and the negative side of the battery the positive side should face up Used batteries must be handled in accordance with local environmental regulations 15 13 CLR CMOS Clear CMOS Jumper Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults To clear the CMOS values use a metal object like a screwdriver to touch the two pins for a few seconds T Open Normal GE Short Clear CMOS Values e Always turn off your computer and unplug the power cord from the power outlet before clearing the CMOS values After system restart go to BIOS Setup to load factory defaults select Load Optimized Defaults or manually configure the BIOS settings refer to Chapter 2 BIOS Setup for BIOS configurations 14 CI Chassis Intrusion Header This motherboard provides a chassis detection feature that detects if the chassis cover has been removed This function requires a chassis with chassis intrusion detection design Pin No Definition t Signal 1 2 GND 16 Chapter M BIOS Setup BIOS Basic Input and Output System records hardware parameters of the system in the CMOS on the motherboard Its major functions include conducting the Power On Self Test POST during system startup saving system parameters and loading operating system etc BIOS includes a BIOS Setup program
22. bility Support Module to support a legacy PC boot process gt Enabled Enables UEFI CSM Default gt gt Disabled Disables UEFI CSM and supports UEFI BIOS boot process only Boot option filter Allows you to select which type of operating system to boot gt gt UEFI and Legacy Allows booting from operating systems that support legacy option ROM or UEFI option ROM Default gt Legacy only Allows booting from operating systems that only support legacy option ROM gt gt UEFI only Allows booting from operating systems that only support UEFI option ROM This item is configurable only when CSM Support is set to Enabled Network Allows you to select whether to enable the UEFI or legacy option ROM for the LAN controller Do not launch Disables option ROM Default gt gt UEFI only Enables UEFI option ROM only gt Legacy only Enables legacy option ROM only gt gt Legacy First Enables legacy option ROM first gt gt UEFI First Enables UEFI option ROM first This item is configurable only when CSM Support is set to Enabled 21 v Storage Allows you to select whether to enable the UEFI or legacy option ROM for the storage device controller gt gt Do not launch Disables option ROM gt gt UEFI only Enables UEFI option ROM only gt Legacy only Enables legacy option ROM only Default gt gt Legacy First Enables legacy option ROM first gt gt UEFI First Enables UEFI option ROM first Thi
23. d 6 D Sub Port The D Sub port supports a 15 pin D Sub connector and supports a maximum resolution of 2560x1600 the actual resolutions supported depend on the monitor being used Connect a monitor that supports D Sub connection to this port HDMI Port 4 minnie The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD HIGH DEFINITION MuLTimeoia intenrace Master Audio formats It also supports up to 192KHz 24bit 8 channel LPCM audio output You can use this port to connect your HDMI supported monitor The maximum supported resolution is 1920x1080 but the actual resolutions supported are dependent on the monitor being used After installing the HDMI device make sure to set the default sound playback device to HDMI The item name may differ depending on your operating system gm Dual Display Configurations for the Onboard Graphics Dual display configurations are supported after you install motherboard drivers in OS but not during the BIOS Setup or POST process USB 3 0 2 0 Port The USB 3 0 port supports the USB 3 0 specification and is compatible to the USB 2 0 1 1 specification Use this port for USB devices such as a USB keyboard mouse USB printer USB flash drive and etc USB 2 0 1 1 Port The USB port supports the USB 2 0 1 1 specification Use this port for USB devices such as a USB keyboard mouse USB printer USB flash drive and etc RJ 45 LAN Port The Gigabit Ethernet LAN port provides Internet connecti
24. defaults after updating the BIOS or after clearing the CMOS values Save as User Defaults Save to current BIOS settings as user defined default settings Restore User Defaults Load the user define default settings for all BIOS options Boot Override Allows you to select a device to boot immediately Press lt Enter gt on the device you select and select Yes to confirm Your system will restart automatically and boot from that device Launch EFI Shell From filesystem service Allows you to launch the EFI Shell application shell efi from one of the available filesystem devices Press Enter on this option and the system will restart to the EFI Shell screen automatically 2f Chapter 3 Appendix Drivers Installation Windows 8 1 as the example operating system e After installing the operating system insert the motherboard driver disk into your optical drive Click on the message Tap to choose what happens with this disc on the top right corner of the screen and select Run Run exe Or go to My Computer double click the optical drive and execute the Run exe program CA Before installing the drivers first install the operating system The following instructions use After inserting the driver disk Xpress Install will automatically scan your system and then list all the drivers that are recommended to install You can click the Install All button and Xpress Install will install all the recommended drivers Or click Inst
25. directive E S subject to the following two conditions 1 This device may not X CE marking cause harmful and 2 this device must accept any inference received C including that may cause undesired operation Representative Person s Name ERIC LU Signature Eric Lu Signature Timmy Huang Date May 16 2014 Stamp Date May 16 2014 Name Timmy Huang Copyright 2014 GIGA BYTE TECHNOLOGY CO LTD All rights reserved The trademarks mentioned in this manual are legally registered to their respective owners Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice No part of this manual may be reproduced copied translated transmitted or published in any form or by any means without GIGABYTE s prior written permission BI In order to assist in the use of this product carefully read the User s Manual BI For product related information check on our website at http www gigabyte com Identifying Your Motherboard Revision The revision number on your motherboard looks like this REV X X For example REV 1 0 means the revision of the motherboard is 1 0 Check your motherboard revision before updating motherboard BIOS drivers or when looking for technical information Example Table of Contents GA J1800N D2H GA J1900N D2H Motherboa
26. ipment is no longer useful to you take it back to your local or regional waste collection administration for recycling f you need further assistance in recycling reusing in your end of life product you may contact us at the Customer Care number listed in your product s user s manual and we will be glad to help you with your effort Finally we suggest that you practice other environmentally friendly actions by understanding and using the energy saving features of this product where applicable recycling the inner and outer packaging including shipping containers this product was delivered in and by disposing of or recycling used batteries properly With your help we can reduce the amount of natural resources needed to produce electrical and electronic equipment minimize the use of landfills for the disposal of end of life products and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly 29 FCC Notice U S A Only This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfe
27. l Port Header The LPT header can provide one parallel port via an optional LPT port cable For purchasing the optional LPT port cable please contact the local dealer Pin No Definition Pin No Definition Pin No Definition STB 10 GND 19 ACK 7 SATA2 0 1 SATA 3Gb s Connectors The SATA connectors conform to SATA 3Gb s standard and are compatible with SATA 1 5Gb s standard Each SATA connector supports a single SATA device Pin No Definition GND TXP TXN GND RXN RXP GND SATA2 ce m4 NN OD om BB wy DM gt 8 F PANEL Front Panel Header Connect the power switch reset switch and system status indicator on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables e PLED Power LED Yellow Power LED Power Switch System Status LED 90 On 3 S4 S5 Off PW Power Switch Red Connects to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch refer to Chapter 2 BIOS Setup Chipset for more information HD Hard Drive Activity LED Blue Connects to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data Connects to the power status indicator on the chassis fr
28. on at up to 1 Gbps data rate The following describes the states of the LAN port LEDs SAID AcivyLgp Connection Speed LED Activity LED State Description State Description m Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring hm Green 100 Mbps data rate Off No data transmission or receiving is occurring Off 10 Mbps data rate LAN Port e Line In Jack Blue The line in jack Use this audio jack for line in devices such as an optical drive walkman etc Line Out Jack Green The line out jack Use this audio jack for a headphone or 2 channel speaker This jack can be used to connect front speakers in a 4 5 1 7 1 channel audio configuration Mic In Jack Pink The Mic in jack Microphones must be connected to this jack To configure 7 1 channel audio you have to use an HD front panel audio module and enable the multi channel audio feature through the audio driver When removing the cable connected to a back panel connector first remove the cable from your N device and then remove it from the motherboard e When removing the cable pull it straight out from the connector Do not rock it side to side to prevent an electrical short inside the cable connector 1 6 Internal Connectors 5 1 13 8 2 mile ABBAA OLED EEEEEEEEEEEER 3 CED P E 9 E 3 12 1 ATX 12V 8 F PANEL 2 ATX 9 F AUDIO 3 CPU FAN 10 F USB 4 SYS FAN 11 SPDIF O 5
29. ont panel The LED is on when the system is operating The LED is off when the system is in S3 S4 sleep state or powered off S5 e RES Reset Switch Green Connects to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart NC Purple No connection EB The front panel design may differ by chassis A front panel module mainly consists of power switch reset switch power LED hard drive activity LED and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assignments are matched correctly 9 F AUDIO Front Panel Audio Header The front panel audio header supports Intel High Definition audio HD and AC 97 audio You may connect your chassis front panel audio module to this header Make sure the wire assignments of the module connector match the pin assignments of the motherboard header Incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it For HD Front Panel Audio Pin No Definition MIC2 L GND MIC2 R 10 2 ACZ DET LINE2 R GND FAUDIO JD No Pin coco NI oIa AIIN LINE2_L GND For AC 97 Front Panel Audio Pin No Definition MIC GND MIC Power NC Line Out R NC
30. phics cards may require you to use a S PDIF digital audio cable for digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display to the graphics card and have digital audio output from the HDMI display at the same time For information about connecting the S PDIF digital audio cable carefully read the manual for your expansion card Pin No Definition 8 1 SPDIFO 1 2 GND 12 BAT Battery The battery provides power to keep the values such as BIOS configurations date and time information in the CMOS when the computer is turned off Replace the battery when the battery voltage drops to a low level or the CMOS values may not be accurate or may be lost You may clear the CMOS values by removing the battery 1 Turn off your computer and unplug the power cord 2 Gently remove the battery from the battery holder and wait for one minute Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 3 Replace the battery 4 Plug in the power cord and restart your computer Always turn off your computer and unplug the power cord before replacing the battery Replace the battery with an equivalent one Danger of explosion if the battery is replaced with an incorrect model Contact the place of purchase or local dealer if you are not able to replace the battery by yourself or uncertain about the
31. r password or user password at system startup and when entering BIOS Setup However the user password only allows you to make changes to certain BIOS settings but not all To cancel the password press Enter on the password item and when requested for the password enter the correct one first When prompted for a new password press Enter without entering any password Press Enter again when prompted to confirm 24 gt Secure Boot menu System Mode Displays the current system mode Secure Boot Displays the current secure boot state Secure Boot Enables or disables the secure boot function Secure Boot requires all the applications that are running during the booting process to be pre signed with valid digital certificates This way the system knows all the files being loaded before Windows 8 loads and gets to the login screen have not been tampered with Default Disabled Secure Boot Mode Allows you to configure the secure boot mode Default Custom gt Key Management This section provides you with configuration options for secure boot key management 2 6 Boot Aptio Setup Utility Copyright C 2013 American Megatrends Inc Main Advanced Chipset Security Save amp Exit Boot Configuration Setup Prompt Timeout 6 Bootup NumLock State On Full Screen Logo Show Enabled Fast Boot Disabled Boot Option Priorities Boot Option 1 UEFI USB 2 0 F Boot Option 22 UEFI Built in EFI Hard Drive
32. rd Layout sssssss 4 GA J1800N D2H GA J1900N D2H Motherboard Block Diagram 9 Chapter 1 Hardware Installation cccccccssscssscsscssecsscsssscsscessecsssessecssessesesesaseeseeees 6 t1 STAN AVON I II NE SETS 6 1 22 POC Ae ONS sinice 7 1 3 Installing the Memory esseri aa TAATA T 9 1 4 Installing an Expansion Card iio ccccicccsediccsscansseatssacesdteacsesdiesraccseasserasecessabnseaee 9 1 6 Back Panel Coe Cor Seciu aa Ta 9 t6 Mermal Connections cocsssaatuscetetnu D E is 11 chanter 2 BIOS SPUD ene earn en a aa ne eee eee 17 MEME pei Nm 17 e IRE EO EET 18 Z3 PROVING GU teers screed E E Te sub OF REDUCIR EU MA 19 Zu ND E ocosesdnce tite mute E dee uM aM pEetU MEE 23 Ao O a NR auraeseedessesrestenecetee 24 LO POO oera A E E E 25 EY GM cc RR Uu eee ere eee eee 2 Chapter 9 9 DDETTODO iesu derat gian cete ute red fmt MEER ERU NP UD UE 28 Drivers MS AN AMON m 28 Regulatory SAIS MOMS onte cesi ete vtae tiques taxi th den Sis ot act US cue Lem 29 Salele AU M 32 COM F PANEL J ey TAD Ys Te SYST D SY au DEEST IY E ESYS Y THESE ATX ATANAN CLR CMOS CPU_FAN Intel J1800 SoC Intel J1900 SoCO E O N SO DIMM 2 m Realtek GbE LAN M BIOS L SYS_FAN TE B l F AUDIO sppir o E MINI PCIE GA J1800N D2H GA J1900N D2H copec mem mmm SATA2 PCIEX1 Box Contents V GA J1800N D2H or
33. rence to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult a dealer or experienced TV radio technician for help Canada Industry Canada IC Notices Canada avis d Industry Canada IC This Class B digital apparatus complies with Canadian ICES 003 and RSS 210 Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device Cet appareil num rique de classe B est conforme aux normes canadiennes ICES 003 et RSS 210 Son fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne doit pas causer d interf rence et 2 cet appareil doit accepter toute interf rence notamment les interf rences qui peuvent affecter son fonctionnement 30 04 Contact Us GIGA BYTE
34. row keys to move among the items and press Enter to accept or enter a sub menu Main Menu Help The on screen description of a highlighted setup option is displayed on the bottom line of the Main Menu Submenu Help While in a submenu press F1 to display a help screen General Help of function keys available for the menu Press Esc to exit the help screen Help for each item is in the Item Help block on the right side of the submenu Sample BIOS Version GA J1900N D2H F 1c When the system is not stable as usual select the Restore Defaults item to set your system to its defaults The BIOS Setup menus described in this chapter are for reference only and may differ by BIOS version Aptio Setup Utility Copyright C 2013 American Megatrends Inc Advanced Chipset Security Boot Save amp Exit BIOS Information BIOS ID 8A05AG07 Project Nate J1900N D2H BIOS Version Fic Build Date and Time 04 07 2014 14 46 18 Memory Information Total Memory 2048 MB LPDDR3 System Language English System Date Fri 04 11 2014 System Time 17 53 46 gt Select Screen T4 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Access Level Administrator Version 2 16 1242 Copyright C 2013 American Megatrends Inc This section provides information on your motherboard model and BIOS version You can also select the default l
35. s item is configurable only when CSM Support is set to Enabled Video Allows you to select whether to enable the UEFI or legacy option ROM for the graphics controller gt gt Do not launch Disables option ROM gt gt UEFI only Enables UEFI option ROM only gt Legacy only Enables legacy option ROM only Default gt gt Legacy first Enables legacy option ROM first UEFI first Enables UEFI option ROM first This item is configurable only when CSM Support is set to Enabled Other PCI Device ROM Priority Allows you to select whether to enable the UEFI or Legacy option ROM for the PCI device controller other than the LAN storage device and graphics controllers gt gt UEFI First Enables UEFI option ROM only Default gt Legacy only Enables legacy option ROM only This item is configurable only when CSM Support is set to Enabled USB Configuration Legacy USB Support Allows USB keyboard mouse to be used in MS DOS Default Enabled USB3 0 Support Enables or disables the USB 3 0 controller Default Enabled XHCI Hand off Determines whether to enable XHCI Hand off feature for an operating system without XHCI Hand off support Default Enabled EHCI Hand off Determines whether to enable EHCI Hand off feature for an operating system without EHCI Hand off support Default Disabled USB Mass Storage Driver Support Enables or disables support for USB storage devices Default Enabled USB Storage Devices
36. sticker provided by your dealer These stickers are required for warranty validation Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components When connecting hardware components to the internal connectors on the motherboard make sure they are connected tightly and securely When handling the motherboard avoid touching any metal leads or connectors It is best to wear an electrostatic discharge ESD wrist strap when handling electronic components such as a motherboard CPU or memory If you do not have an ESD wrist strap keep your hands dry and first touch a metal object to eliminate static electricity Prior to installing the motherboard please have it on top of an antistatic pad or within an electrostatic shielding container Before unplugging the power supply cable from the motherboard make sure the power supply has been turned off Before turning on the power make sure the power supply voltage has been set according to the local voltage standard Before using the product please verify that all cables and power connectors of your hardware components are connected To prevent damage to the motherboard do not allow screws to come in contact with the motherboard circuit or its components Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing Do not place the computer system on an
37. t Security Eo Save amp Exit Password Description If ONLY the Administrator s password is set then this only limits access to Setup and is only asked for when entering Setup If ONLY the User s password is set then this is a power on password and must be entered to boot or enter Setup In Setup the User will have Administrator rights The password length must be in the following range Minimum length 2 Maximum length Select Screen T4 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Administrator Password User Password gt Secure Boot menu Version 2 16 1242 Copyright C 2013 American Megatrends Inc Administrator Password Allows you to configure an administrator password Press Enter on this item type the password and then press Enter You will be requested to confirm the password Type the password again and press Enter You must enter the administrator password or user password at system startup and when entering BIOS Setup Differing from the user password the administrator password allows you to make changes to all BIOS settings lt gt User Password Allows you to configure a user password Press Enter on this item type the password and then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt You must enter the administrato
38. tatus to Enabled save the settings to the CMOS and then restart your system Only for GA J1900N D2H gt gt Reset Case Open Status Disabled Keeps or clears the record of previous chassis intrusion status Default gt gt Enabled Clears the record of previous chassis intrusion status and the Case Open field will show Close at next boot CPU Configuration Socket 0 CPU Information This section provides information on your CPU frequency and cache memory CF v v Limit CPUID Maximum Allows you to determine whether to limit CPUID maximum value Set this item to Disabled for Windows XP operating system set this item to Enabled for legacy operating system such as Windows NT4 0 Default Disabled Execute Disable Bit Enables or disables Intel Execute Disable Bit function This function may enhance protection for the computer reducing exposure to viruses and malicious buffer overflow attacks when working with its supporting software and system Default Enabled Hardware Prefetcher Enables or disables L2 Cache Hardware Prefetcher Default Enabled Adjacent Cache Line Prefetch Enables or disables L2 prefetching of adjacent cache lines Default Enabled Intel Virtualization Enables or disables Intel Virtualization Technology Virtualization enhanced by Intel Virtualization Technology will allow a platform to run multiple operating systems and applications in independent partitions With virtualiz
39. that allows the user to modify basic system configuration settings or to activate certain system features When the power is turned off the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS To access the BIOS Setup program press the Delete key during the POST when the power is turned on To upgrade the BIOS use the GIGABYTE BIOS utility which is a Windows based utility that searches and downloads the latest version of BIOS from the Internet and updates the BIOS Because BIOS flashing is potentially risky if you do not encounter problems using the current version of BIOS it is recommended that you not flash the BIOS To flash the BIOS do it with caution Inadequate BIOS flashing may result in system malfunction tis recommended that you not alter the default settings unless you need to to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs try to clear the CMOS values and reset the board to default values Refer to the Restore Defaults section in this chapter or introductions of the battery clear CMOS jumper in Chapter 1 for how to clear the CMOS values 2 Startup Screen The following startup Logo screen will appear when the computer boots GIGABYTE 2 2 Main Once you enter the BIOS Setup program the Main Menu as shown below appears on the screen Use ar
40. uneven surface Do not place the computer system in a high temperature environment Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user If you are uncertain about any installation steps or have a problem related to the use of the product please consult a certified computer technician 1 2 Product Specifications 45 CPU Built in with an Intel Dual Core Celeron J1800 SoC 2 41 GHz Built in with an Intel Quad Core Celeron J1900 SoC 2 0 GHz O Donotdisassemble the onboard SoC and the heatsinks by yourself to avoid damage to these components 1 MB Cache 2 MB Cache 2 x 1 35V DDR3L DIMM sockets supporting up to 8 GB of system memory If only one DDR3L memory module is to be installed be sure to install it in the SODIMM_1 socket Dual channel memory architecture Support for DDR3L 1333 MHz memory modules Support for non ECC memory modules Onboard Graphics 9 Integrated in the SoC 1 x D Sub port supporting a maximum resolution of 2560x1600 1 x HDMI port supporting a maximum resolution of 1920x1080 Audio Realtek ALC887 codec High Definition Audio 2 4 5 1 7 1 channel To configure 7 1 channel audio you have to use an HD front panel audio module and enable the multi channel audio feature through the audio driver Support for S PDIF Out LAN Realtek GbE LAN chip 10 100 1000 Mbit
Download Pdf Manuals
Related Search