Klipsch IC-400-T
Contents
1. IC 650 T IC 525 T amp IN CEILING LOUDSPEAKERS IC 400 T OwNER S MANUAL AND WARRANTY 1C 400 T I1C 525 T amp ic 650 T Thank you for purchasing your Klipsch IC 400 T IC 525 T or IC 650 T in ceiling speakers The IC 400 T IC 525 T and IC 650 T in ceiling speakers have been designed for music reinforcement applications Unobtrusive these loudspeakers are engineered for easy versatile installation The IC 400 T IC 525 T and IC 650 T feature an internal transformer for 7OV 100V distributed line systems The transformer taps are selected using a rotary switch located conveniently under the grille For applications where 8 ohm operation is required the transformer can be by passed by using an optional connection located on the back input terminal and selectin 8 Ohm on the front switch Before installing your speakers take a moment to check the contents of the cartons and make sure nothing has been damaged in transit Contents Description QUANTITY Speaker Modules Grille Reinforcement Ring Rails Cardboard Cutout Template and Paint Mask Screws Attach Rails to Reinforcement Ring 3 Adapter Fittings N O F BRN S ki Installation Guidelines The IC 400 T IC 525 T and IC 650 T include a tilebridge for use when installing the loudspeaker into suspended ceilings or wher ever additional reinforcement of the ceiling material is required The tilebridge and loudspeaker are designed such that installa2. SENSITIVITY 2 83 V 1M 90dB COVERAGE 105 degrees DI 6 5 dB Q 4 5 NOMINAL IMPEDANCE 8 ohms min 4 4 ohms switch set in 8 ohm position DIAMETER 10 CUTOUT DIAMETER 10 125 OVERALL DEPTH 10 938 MOUNTING DEPTH 10 625 WEIGHT li 25 bs INPUT CONNECTORS Terminal Strip TRANSFORMER TAPS 70V 60W 30W 15W 7 5W 100V 60W 30W 15W FINISHES Black and White TRANSDUCERS 6 5 WOOFER AND 1 TITANIUM DIAPHRAGM COMPRESSION DRIVER ON A 3 5 ROUND XT MODIFIED TRACTRIX HORN ENCLOSURE TUNING Vented Via A 1 Tractrix port Klipsch Limited Warranty KLIPSCH AUDIO TECHNOLOGIES KLIPSCH warrants this product to be free from defects in materials and workmanship subject to the terms set forth below for a period of five 5 years from the date of purchase During the Warranty period KLIPSCH will repair or replace at KLIPSCH s option this product or any defective parts excluding electronics and amplifiers For products that have electronics or amplifiers the Warranty on those parts is for a period of two 2 years from the date of purchase To obtain Warranty service please contact the KLIPSCH authorized dealer from which you purchased this product If your dealer is not equipped to perform the repair of your KLIPSCH product it can be returned freight paid to KLIPSCH for repair Please call KLIPSCH at 1 800 KLIPSCH for instructions You will need to ship this product in either its original packaging or packaging affording an equal degree of protection P
3. tion may be accomplished where access above the ceiling is not possible or may be difficult Installation 1 The tilebridge is composed of three parts a reinforcement ring and two rails The two rails should be attached to the reinforce ment ring using the four included screws as shown below Caution Be sure to comply with any and all building codes in your area 2 To install your IC 400 T IC 525 T or IC 650 T cut out a hole in the ceiling using either the cardboard cutout template provided with your speakers or consult the measurements below Pull wiring through hole 9 125 Round IC 400 T IC 525 T IC 650 T 10 125 Round 3 To install the tilebridge fold the rail side of the ring back upon itself using the spring tensioner on the reinforcement ring to allow insertion into the cutout hole Once it is inserted into the cutout hole release the reinforcement ring such that it unfolds back to its normal position Position tilebridge over cutout hole and insure that the tile rails rest on the t grid struts 4 The wiring compartment is intended as a termination point for the audio circuit Access to this compartment is gained by removing the terminal cover located on the back of the speaker The terminal cover will accept the appropriate conduit wire adapter provided Feed wires through conduit wire adapter and connect to the input terminal according to the desired operation mode Be sure to observe proper polarity
4. Replace the terminal cover and tighten the conduit wire adapter to secure the wire Caution When connecting 70V or 100V distributed line systems take care to ensure proper terminal connection Connection to the low impedance termi nal could result in speaker damage amplifier damage or both o 7 ES oi 70 100v Common 8 ohm 5 Insert the soeaker into the cutout hole With a 2 Phillips screw driver tighten the four dog clamps until they are seated securely against the ceiling surface Do not overtighten 6 For installations using 70v 100v input connection set the switch on the front panel to the desired setting For applications where 8 Ohm impedance is desired the switch should be set to 8 Ohms Note The speaker comes from the factory set at the lowest output setting highest impedance 7 Using the flat of your hand insert grille into soeaker frame making sure it is securely seated and flush Seismic Tab A seismic tab located on the back of the speaker is Used as a secondary security point Some construction codes may require its use To utilize the seismic tab run a support wire from a secure point in the ceiling and attach it to the tab Be sure to consult the construction codes in your area Klipsch recommends the use of this tab in all installations as q secondary means of support IC 650 T tap selectable IC A00 T FREQUENCY RESPON
5. SE CONT POWER HAND CALC MAX CONT OUTPUT 1M SENSITIVITY 2 83 V 1M COVERAGE DI Q NOMINAL IMPEDANCE DIAMETER CUTOUT DIAMETER OVERALL DEPTH MOUNTING DEPTH WEIGHT INPUT CONNECTORS TRANSFORMER TAPS FINISHES TRANSDUCERS ENCLOSURE TUNING IC 525 T FREQUENCY RESPONSE CONT POWER HAND CALC MAX CONT OUTPUT 1M SENSITIVITY 2 83 V 1M COVERAGE DI Q NOMINAL IMPEDANCE DIAMETER CUTOUT DIAMETER OVERALL DEPTH MOUNTING DEPTH WEIGHT INPUT CONNECTORS TRANSFORMER TAPS FINISHES TRANSDUCERS ENCLOSURE TUNING N G 70 20k Hz 4 dB 50 watts 14 5V 100 dB 86dB 80 degrees 8 dB 6 3 8 ohms min 4 2 ohms when switch is set to 8 ohm position 9 9 125 8 313 g 6 25 bs Terminal Strip 70V 15W 7 5W 3 8W 1 9W Black and White 5 WOOFER AND 1 TITANIUM DIAPHRAGM COMPRESSION DRIVER ON A 2 ROUND TRACTRIX HORN Vented Via A 1 Tractrix port 100V 15W 7 5W 3 8W 65 20k Hz 4 dB 65 watts 16 5V 104 dB 89dB 105 degrees 6 5 dB 4 5 8 ohms min 4 2 ohms switch set in 8 ohm position 9 9 125 9 188 8 875 8 25 lbs Terminal Strip 70V 30W 15W 7 5W 3 8W Black and White 100V 30W 15W 7 5W 5 75 WOOFER AND 1 TITANIUM DIAPHRAGM COMPRESSION DRIVER ON A 3 5 ROUND XT MODIFIED TRACTRIX HORN Vented Via A 1 Tractrix port S P E A K ERS IC 650 T FREQUENCY RESPONSE 50 20k Hz A dB CONT POWER HAND 80 watts 18 8 V CALC MAX CONT OUTPUT 1M 106 dB
6. URPOSE Some states do not allow the exclusion or limitation of incidental or consequential damages or implied warranties so the above exclusions may not apply to you This Warranty gives you specific legal rights and you may have other rights which vary from state to state 2007 Klipsch Group Inc All Rights Reserved Specifications Subject to Engineering Changes T 3502 Woodview Trace Indianapolis Indiana 46268 USA 1 800 KLIPSCH e www klipsch com 1008997
7. roof of purchase in the form of a bill of sale or receipted invoice which is evidence that this product is within the Warranty period must be presented or included to obtain Warranty service This Warranty is invalid if a the factory applied serial number has been altered or removed from this product or b this product was not purchased from a KLIPSCH authorized dealer You may call 1 800 KLIPSCH to confirm that you have an unaltered serial number and or you purchased from a KLIPSCH authorized dealer This Warranty does not cover cosmetic damage or damage due to misuse abuse negligence acts of God accident commercial use or modification of or to any part of the product This Warranty does not cover damage due to improper operation maintenance or installa tion or attempted repair by anyone other than KLIPSCH or a KLIPSCH dealer which is authorized to do KLIPSCH warranty work Any unau thorized repairs will void this Warranty This Warranty does not cover product sold AS IS or WITH ALL FAULTS REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER KLIPSCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT EXCEPT TO THE EXTENT PROHIBITED BY LAW THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS AND IMPLIED WARRANTIES WHATSOEVER INCLUDING BUT NOT LIMITED TO THE WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PRACTICAL P
Download Pdf Manuals
Related Search