Home

VARO POWXG9007 high-pressure cleaner

1. RR 16 15 o PEE 16 16 PREPARATION FOR WINTER AND LONG TERM STORAGE 16 17 TROUBLE SHOOTING eee eee ene 17 18 0 mmmE 17 19 ENVIRONMENT EE 18 20 DECLARATION OF CONFORMITY 18 Copyright 2013 VARO NV Page 2 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 GASOLINE PRESSURE WASHER POWXG9007 1 APPLIANCE Your gasoline high pressure cleaner has been designed for outdoors cleaning Cleaning of machines vehicles structures tools facades terraces gardening tools operating at gas stations or other dangerous areas Please do not let mineral oil contaminated waste water reach soil water or the sewage system Perform engine cleaning and bottom cleaning therefore only on specified places with an oil trap 1 Danger Risk of injury Follow the respective safety regulations when Warning Read this manual and the general safety instructions carefully before using the machine for your own safety 2 DESCRIPTION Picture 1 15 Spray wand 1 Handle 16 Recoil starter cord 2 Hose Reel 17 Engine recoil starter 3 M High pressure hose 12m Picture 2 4 Trigger gun 18 Throttle control level 5 Safety lock 19 Choke 6 Lance Hook 20 Fuellever 7 Nozzles Picture 3 8 Accessory Tray 21 High pressure outlet 9 Carriage bolts 22 Water inlet connector 10 Air filter 23 Detergent filter 11 Fuel tank 24 Detergent su
2. end of the lance Release the collar to lock the nozzle into position To disconnect a nozzle slide the collar back towards the gun the nozzle can now be removed Note please be sure that you crosscheck the correct connection of the nozzle Warning the nozzle is not properly fixed when the collar doesn t slide back Push the nozzle with high force into the opening otherwise the collar doesn t slide back by itself and the nozzle is shot out 10 8 Using the detergent facility Fill a suitable container with pressure washer detergent Do not use washing up liquid as it contains salt We recommend the use of a good quality pressure washer detergent for use with this pressure washer Please follow the instructions on the container Most automobile detergents are a combination of a detergent and a wax solution wash wax liquid These tend to be a thick viscous liquid The viscosity thickness of the detergent will increase in cold weather It is recommended that this type of detergent is diluted with warm water before filling the container When using combination wash and wax solutions we recommend that they are diluted before use As a general guide we would recommend a dilution rate of 50 50 However a trial and error process would determine the ideal dilution rate for a particular detergent Notes A thick viscous detergent would not flow freely from the detergent tank and the residue would cause a blockage in the detergen
3. filter Warning Never run the engine without the air filter fitted 14 2 4 Fuel tank filter 15 STORAGE If the engine picture 1 part 14 is not to be used or is to be stored for more than one month the following storage procedure should be carried out Drain all the fuel from the fuel tank picture 1 part 11 and the carburettor ensure that all the fuel has been removed Remove the spark plug Pour approximately one tablespoon full of clean engine oil into the spark plug hole With the ignition turned OFF gently pull on the recoil starter cord picture 1 part 16 several times Re fit the spark plug continue to pull the recoil starter cord until the piston is on the compression stroke when resistance is felt then stop pulling Store the pressure washer in a dry well ventilated place under a cover to prevent any dust or debris from accumulating on the pressure washer 16 PREPARATION FOR WINTER AND LONG TERM STORAGE If the pressure washer is not to be used for more than 3 months or if there is a danger of ice or frost during winter months the pump unit will require protection to prevent seizing and damage caused by freezing To protect the pump unit mix a solution of automotive antifreeze as recommended on the antifreeze packaging Carefully pour the solution into the pressure washer pump inlet When the solution drains out of the outlet seal the outlet with a cork or other suitable bung Continue to pour the antifreeze soluti
4. not securely locked into place It could be injected under high pressure when operation the gun possibly causing injury or damage 11 3 Start engine Turn the fuel lever picture 2 part 20 to the ON position Set the choke lever picture 2 part 19 to the ON position Turn the engine ON OFF switch picture 3 part 26 to the ON position Hold down the engine firmly with one hand on the frame With the other hand grip the recoil starter cord picture 1 part 16 handle and pull slowly until resistance is felt indicating that the recoil starter picture 1 part 17 is engaged When resistance is felt pull the cord sharply Continue this procedure until the engine starts Copyright 2013 VARO NV Page 12 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 When the engine has been successfully started and is running smoothly return the choke lever picture 2 part 19 to the OFF position When the engine is running the speed can be adjusted by moving the throttle control lever picture2 part 18 When you slide the throttle to the right the engine will have a lower rotation speed To obtain a higher rotation speed you have to slide the throttle more to the left To stop the engine turn the engine ON OFF switch picture 3 part 26 to the OFF position Warning After the engine has stopped turn off the water supply to the pressure washer and release all remaining pressure by operating the trigger u
5. ENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool 5 1 Working environment Store the pressure washer in a well ventilated area with the fuel tank empty Fuel should not be stored near the pressure washer Equipment must be placed on a firm supporting surface Outdoors use only never operate in an enclosed space exhaust fumes are dangerous Place the pressure washer away from cleaning site during operation Keep children and bystanders away while operating a power tool This appliance must be attended during operation 5 2 Personal safety Stay alert watch what you are doing and use common sense when operating a power tool A moment of inattention while operating the power tools may result in serious personal injury Wear safety goggles while operating Small particles may fly out while spraying Always wear ear protection to cut noise Dress safely in long pants and wear boots or shoes Other protective equipment is advisable when using chemicals cleaning detergents or other corrosive or abrasive substances Do not overreach Keep proper footing and balance at all times This enables better control of th
6. GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 1 o HMM 3 2 0 0 Pm 3 3 PACKAGE CONTENT LIST uua 3 4 4 5 GENERAL POWER TOOL SAFETY WARNINGS 4 5 1 Worki g 2iqergo r1 get 4 5 2 laci 4 5 3 Correct use and Care em 5 6 STANDARDIZED SAFETY WARNINGS FOR GASOLINE HIGH PRESSURE o T 6 7 SAFETY WARNINGS GASOLINE 6 8 DEUM UE eren nnn nnn nnn nnn nun nns 6 8 1 Th rmal relef valv 6 8 2 Salely JOCK OFF ION mtt 6 9 ASSEMBLY INSTRUCTIONS ees T 9 1 Attach handle and BOOK doin cde ssdecdntectiecd rou oa 6o tees een detdececteedeendecs 7 9 2 Installing the WINGO S M 7 9 3 assembly of the DODDIN viiesa Naai AS REAREA EEEE 7 9 4 Assembling the bobbin l0CkK orien retine penas oandencesssaeiwesersvinetetewcesternacenenees 7 9 5 USING e DODDINIOCK scri 8 10 BEFORE OPERAT ION eurmerrrrn nnn nnn nnn nuni 8 10 1 Add oil to the engine crankcase 12 Lesser iiie esee enis essen nana nana naa u nnn 8 10 2 Add Tuel to fuel TANK iiid ioi e esee tie Si hinter es eoo oscus 8 10 3 Connect high pressure hose to s
7. ct gap should be 0 7 to 0 8mm 14 2 2 Engine oil replacement We recommend that the oil be changed after the first 40 hours of use then once every 100 hours Place the machine on a level surface and warm up the engine for several minutes Then stop the engine Place a suitable container below the pump to catch the used oil Remove the oil fill cap oil drain plug and the washer so that the oil can be completely drained You will need to use a tube or other similar device to prevent the oil leaking onto the frame of the pressure washer Check the oil drain plug gasket oil filler cap and O ring and if damaged replace Reinstall the oil drain plug and the washer Tighten the drain plug securely Add engine oil to at least half of the dipstick Reinstall the oil fill cap securely Please dispose of used motor oil in a manner that is compatible with the environment We suggest you take it in a sealed container to your local service station for reclamation Do not throw it in the trash or pour it on the ground Copyright 2013 VARO NV Page 15 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 14 2 3 Air filter After every 100 hours of running or every month the air filter picture 1 part 10 should be removed examined for deterioration and cleaned Clean the air filter thoroughly using environmentally friendly water based degreasing agent Allow to dry fully then replace the air
8. ction tube 12 Exhaust silencer 25 Oil fill cap 13 Wheel 26 ON OFF switch 14 Engine 3 PACKAGE CONTENT LIST Remove all packaging materials Remove remaining packing and package inserts if included Check that the package contents are complete Check the appliance the power cord the power plug and all accessories for transportation damage Keep the packing materials as far as possible till the end of the warranty period Dispose it into your local waste disposal system afterwards WARNING Packaging materials are not toys Children must not play with plastic bags Danger of suffocation Pneumatic Tire 2 Spark Plug Spanner 1 Gun 1 Nozzle Cleaning Tool 1 Lance 1 5mm Hex Key 1 4mm Hex Key 1 8 10 Wrench 1 10 13 Wrench 1 High Pressure hose 12m Hose Bobbin Assembly 1set Water Inlet Connecter 1 Copyright 2013 VARO NV Page 3 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN Gun Shelf Assembly 1set Manual of Engine 1 Operating Instruction manual 1 oD If any parts are missing or damaged please contact your dealer 4 SYMBOLS The jet must not be directed at persons pets live electrical equipment or the appliance itself Warning danger Engine will not start or will Read manual before usage shut down if the oil level is low Flammable do not smoke Wear ear protection near the pressure washer p Wear eye protection Wear gloves 5 G
9. e lance the gun is fitted with a safety lock To engage the safety lock picture 1 part 5 release the trigger and engage the safety lock between the trigger and the gun body 10 5 Connecting the hose The water inlet connector is fitted with a particle filter and if not fitted must be fitted prior to use Do not run the unit without filter Based on the water quality the filter must be checked and cleaned from time to time In case there are dirt particles in the water supply the filter must be cleaned before each use Otherwise the performance of the unit will be decreased or the pump might get damaged Screw the male water inlet connector onto the pressure washer water inlet picture 3 part 22 Fit a female hose connector to your hose pipe and then connect the female connector onto the male connector Copyright 2013 VARO NV Page 9 WWW Varo com GARDENPRO POWERFLUS HIGH QUALITY TOOLS POWXG9007 EN Connect the high pressure hose to the delivery pipe outlet picture 3 part 21 Turn on the water supply and squeeze the gun trigger picture 1 part 4 until the water flows in a steady stream through the lance Do not use water which exceeds 40T 10 6 Adjusting the spray pattern Warning Always ensure that the wand is fixed correctly Otherwise it could be injected under high pressure when operating the gun possibly causing injury or damage You have the choice of 4 different colour coded nozzles picture 1 pa
10. e power tool in unexpected situations Do not operate pressure washing equipment if you have consumed alcohol or taken medication Copyright 2013 VARO NV Page 4 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN Remove the spark plug or cable from the spark plug to prevent accidental starting When not in use or prior to detaching the high pressure hose Do not ware loose clothing jewellery or anything that may be caught in the engine Keep pets children and bystanders a safe distance away from your work area A minimum of 50 feet is recommended Never point or aim the gun at yourself or anyone else Never put your hand fingers or body directly in front of the spray nozzle Do not smoke near the pressure washer 5 3 Correct use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instruct
11. e using the jet cleaning tool 18 WARRANTY This product is warranted for a 36 month period effective from the date of purchase by the first user This warranty covers all material or production flaws excluding batteries chargers defective parts subject to normal wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc damage or defects resulting from maltreatment accidents or alterations nor the cost of transportation Damage and or defects resulting from inappropriate use also do not fall under the warranty provisions We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Repairs may only be carried out by an authorised customer service centre for Powerplus tools You can always obtain more information at the number 00 32 3 292 92 90 Any transportation costs shall always be borne by the customer unless agreed otherwise in writing Atthe same time no claim can be made on the warranty if the damage of the device is the result of negligent maintenance or overload Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inappropriate usage use for purposes for which the device is not suitable incompetent usage e g not following the instructions given in the manual inexpert assembly lightning str
12. ike erroneus net voltage This list is not exhaustive Acceptance of claims under warranty can never lead to the prolongation of the warranty period nor commencement of a new warranty period in case of a device replacement Devices or parts which are replaced under the warranty therefore remain the property of Varo NV Copyright 2013 VARO NV Page 17 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained Clean ventilation slots carbon brushes serviced regularly etc Your purchase receipt must be kept as proof of date of purchase Your appliance must be returned undismantled to your dealer in an acceptably clean state in its original blow moulded case if applicable to the unit accompanied by proof of purchase 19 ENVIRONMENT Should your appliance need replacement after extended use do not discard it with the household rubbish but dispose of it in an environmentally safe way Please dispose of used motor oil in a manner that is compatible with the environment We suggest you take it in a sealed container to your local service station for reclamation Do not throw it in the trash or pour it on the ground 20 DECLARATION OF CONFORMITY VARO N V Joseph Van Instraat 9 BE2500 Lier BELGIUM declares that product High pressure cleaner Gasoline
13. ions to operate the power tool Power tools are dangerous in the hands of untrained users Never operate under these conditions A noticeable change in engine speed A noticeable loss of pressure The engine misfires Smoke or flames are present enclosed compartment Excessive vibration Rain or inclement weather Keep the pressure washer clean and free of oil mud and other foreign matter Water spray must never be directed towards any electric wiring or directly towards the pressure washer Use both hands to control the wand Do not allow the hose to come in contact with hot muffler Do not touch nozzle or water spray while operating Do not fill the engine with gasoline when the engine is running hot or near an open flame Do not smoke Only approved hoses and nozzles should be used The trigger gun must not lie jammed in position during operation Never lay knots or kink in the high pressure hose All hose connections must be properly connected Prior to starting the pressure washer in cold weather be sure ice has not formed in any part of the equipment To prevent accidental discharge of high pressure water the safety latch on the trigger should be engaged whenever the pressure washer is not in use refer to operating instruction Do not run the pressure washer for more than five minutes without depressing the trigger The Pump might get damaged Check the fuel system periodically for leaks or signs of deterio
14. l hours 10 1 Add oil to the engine crankcase Do not attempt to start the pressure washer without filling the engine crank case picture 3 part 25 with the proper amount and type of oil see technical data In delivery status the pressure washer has no oil inside the engine crank case Operating the unit without oil will cause engine damage Place the machine ona level surface and remove the oil filler cap Add engine oil to at least half of the dipstick 10 2 Add fuel to fuel tank The pressure washer is powered by a four stroke engine picture 1 part 14 which uses unleaded petrol fuel Use a suitable funnel to fill in the fuel to the engines fuel tank picture 1 part 11 Do not spill any fuel or overfill the tank The fuel tank should not be filled above the top of the fuel filter Copyright 2013 VARO NV Page 8 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 10 8 Connect high pressure hose to spray gun and pump Fit the lance to the gun picture 1 part 4 Grip the end of the gun and screw the lance onto the gun ensuring it is tight Do not over tighten as this could damage both the connectors Connect the high pressure hose connector to the connector on the underside of the gun assembly ensuring that it is tight Do not over tighten as this could damage both the connectors 10 4 High pressure lance safety lock In order to prevent accidental operation of the high pressur
15. ntil there is no more pressure in the appliance and the water flow stops secure the trigger with the safety lock picture1 part 5 to prevent unintentional operation Disconnect the lance and drain any residual water from all hoses picture 1 part 3 carefully coil the hoses ensuring that they are not kinked or twisted and check for any other damage replace any damaged hoses Damaged hoses can be dangerous under pressure When the engine has stopped and before storage turn the fuel lever picture 2 part 20 to the OFF position Copyright 2013 VARO NV Page 13 WWW Varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS 12 TECHNICAL DATA MOTOR Maximum torque at 3600 min 1 Operating Speed Fuel tank Fuel Engine Type Starting System Displacement WATER CONNECTION Max feed temperature Min feed volume Min feed pressure Max feed pressure Inlet hose length Inlet hose diameter inner diameter PUMP Working pressure Flow rate Oil quantity pump Oil type pipe engine oil Detergent suck Max recoil force of hand spray gun DIMENSIONS AND WEIGHTS Length x width x height Weight without accessories 13 SOUND EMISSION POWXG9007 EN 4 8kW 3600 min 1 3400 3500 min 1 3 61 Unleaded gasoline OHV 4 stroke Recoil 196cc 40 1200l h 0 2 Mpa 2bar 0 4 MPa 4 bar 15m 12 8mm 1 2 19 MPa 600 I h 75 ml SAE 75W 90 30 70I h 32 49N 950 x 620 x 950 mm 41kg Noise emission value
16. on into the inlet until the pump is full then seal the inlet with a cork or other suitable bung When the pressure washer is to be used for the first time following the antifreeze protection ensure that all the antifreeze is flushed out of the pump hose and lance When the pressure washer is first started small leaks may occur from the pump These will disappear after a short time xlii After every 150 hours of running or every three months the fuel tank filter should be removed and cleaned Remove the fuel tank filler cap and the filter clean the filter thoroughly using environmentally friendly water based degreasing agent and re fit Copyright 2013 VARO NV Page 16 WWW Varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 17 TROUBLE SHOOTING Pump sucking in air Check connections are tight Fluctuating pressure Valves dirty worn out or seized Remove blockage using jet Blocked jet cleaning tool Water leaking from pump Contact customer helpline Pump sucking air from Check tightness of all connections or hose connections Suction delivery valves are bal topics Valve Ng The pump does not reach clogged machine checked by Service the required pressure Centre aoad vave ie stuck Loosen and re tighten regulating screw Check straighten and replace if Kinked inlet and or pressure hose required Pump is running but no water delivery Blocked inlet filter Remove and clean filter Blocked jet Remove blockag
17. onnector 4 Put the bush onto another side of bobbin 5 Then put the side handle into this side of bobbin 6 Tighten its connection by a screw and bolt 7 Put the whole bobbin onto the upper frame and tighten the clips 8 Connect the pressure hose which is connected with water connector to the pump water outlet 9 Connect the pressure hose which is on the bobbin to the spray gun 9 4 Assembling the bobbin lock 1 Put the washer onto the lock pin seat then through the tube and tighten the nut 2 Putthe lock pin through the spring first then through the lock pin seat 3 Fitthe pull ring on the lock pin 4 Now the bobbin lock is finished Copyright 2013 VARO NV Page 7 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 9 5 Using the bobbin lock 1 Lock Pull the lock pin and rotate to the position where the pull ring can get into the lock pin seat Then release and let the lock pin into the howl on the bobbin 2 Unlock Pull the lock pin out of the lock pin seat and rotate about 905 then release 10 BEFORE OPERATION To prepare your pressure washer for operation you will need to perform these tasks Add oil to engine crankcase Add fuel to fuel tank Connect high pressure hose to spray gun and pump Connect water supply to pump Attach nozzle extension to spray gun Note the engine and pump on your new pressure washer will often have an improved performance after a break of severa
18. operated trade mark POWERplus model POWXG9007 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives based on the application of European harmonized standards Any unauthorized modification of the apparatus voids this declaration European Directives including if applicable their amending directives 2004 108 EC 2006 42 EC 2000 14 EC Annex V LwA 103dB A 105dB A 97 68 EC Engine class SN3 EDP Emission durability period 125h Testing authority NSAI Dublin European harmonized standards including if applicable their amendments EN60335 1 2002 EN60335 2 79 2009 EN55012 2007 The undersigned acts on behalf and under the power of attorney of the company management p s foe UN Philippe Vankerkhove Certification Manager Date 22 08 2012 Copyright 2013 VARO NV Page 18 www varo com
19. pray gun and pump esee e nnne 9 10 4 High pressure lance safety lock 11 12 Leee eee reee erii eese eaae nana aan annu nna 9 10 5 CONNECTING INC NOSE 9 10 6 Adjusting the spray pattern ico en traten ubican ideae gne ee n uana AE c enn eeu eeu EenEE 10 10 6 1 O nozzle colored red iiie rte retede dahin rebai e eaea ireak 10 10 6 2 10 6 3 10 6 4 Copyright 2013 VARO NV Page 1 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 10 7 Connect the DOZZIB tir Ea trae ee he me 11 10 8 USING the detergent facility sccisceticccsccescassoeg cosessendong tack eR aa Sea ned soudsoussateaeadbauseenasiaes 11 11 OPERATING INSTRUCTIONS suu 11 11 1 PreSsSure washer locali e 11 11 2 Silar Up DIOCCOUI GS M 12 11 3 21 0475 X A 12 11 4 CIDGNSIEJJSQ e 13 12 TECHNICAL c cene nnne rne nnne nnn nnmis 14 13 o 14 14 CLEANING AND MAINTENANCE 15 14 1 e E Nuec m 15 14 2 Routine maintenant oia boda da i a i REA MERKEN EE EORR nannies 15 14 2 1 lord ele Rm 15 14 2 2 Engine oil replacement 0 ccc ccc ceeccc cence neces cena eeteeeseeeeseneetenessuseseueeteneesesesnees 15 De AiE eee eee 16 taAa LLLI
20. ration such as chafed or spongy hose or missing clamps or damaged tank or cap All defects should be corrected before operation Do not touch hot muffler Service operate and refuel under the following conditions Good ventilation Refuel the pressure washer in a well lighted area Copyright 2013 VARO NV Page 5 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN Avoid fuel spills and never refuel while the pressure washer is running Avoid an ignition source when refuelling Use unleaded free fuel Do not use damaged high pressure hose 6 STANDARDIZED SAFETY WARNINGS FOR GASOLINE HIGH PRESSURE WASHERS WARNING This appliance has been designed for use with the cleaning agent supplied or recommended by the manufacturer The use of other cleaning agents or chemicals may adversely affect the safety of the appliance WARNING Do not use the appliance within range of persons unless they wear protective clothing WARNING High Pressure jets can be dangerous if subject to miss use The jet must not be directed at persons live electrical equipment or the appliance itself Do not direct the jet against yourself or others in order to clean shoes or clothes To ensure appliance safety use only original spare parts from the manufacturer or approved by the manufacturer WARNING High Pressure hoses fittings and couplings are important for the safety of the appliance Use only fittings and coupling
21. rt 7 giving you different AZ spray patterns to choose from 10 6 1 O nozzle colored red This nozzle delivers a pinpoint stream and is extremely powerful It covers a very small area of cleaning This nozzle should only be used on surface that can withstand this high pressure such as metal or concrete Do not use on wood 10 6 2 15 nozzle colored yellow This nozzle delivers a powerful 15 degree spray pattern for intense cleaning of small areas This nozzle should only be used on areas that can withstand the high pressure from this nozzle 10 6 3 40 nozzle colored white This nozzle delivers a 40 degree spray pattern and a less powerful stream of water It covers a wide area of cleaning this nozzle should be used for most general cleaning jobs 10 6 4 Low pressure nozzle colored black This nozzle is used to apply chemicals or cleaning solutions It has the least power stream Note Due to material and workmanship differences high pressure streams can damage patio paving slabs Try on a small test area first If necessary adjust the pressure by changing nozzles or slowing down the engine speed Copyright 2013 VARO NV Page 10 WWW Varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 10 7 Connect the nozzle Connect the nozzle to the lance using the quick release connector this allows the quick and easy changing of nozzles To connect a nozzle slide the collar back towards the gun push the nozzle into the
22. s measured according to relevant standard K 2 Sound pressure level LpA Sound power level LwA individual hearing protection must be worn ATTENTION The sound power pressure may exceed 85 dB A in this case Vibration Hand spray gun Spray lance Copyright 2013 VARO NV K 1 5 m s K 21 5 m s WWW Varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 14 CLEANING AND MAINTENANCE 14 1 Clearing a blockage WARNING Before checking adjustments cleaning or maintaining the pressure washer the engine must be stopped and cooled down Ensure that the pressure is released completely If at any time the flow rate reduces splutters or is inconsistent release the trigger and switch OFF the machine Squeeze the trigger to relieve any pressure and check the jet in the end of the lance for any blockage If a blockage is suspected use the jet cleaning tool to remove any blockage It is important that the water jet is checked and cleaned regularly using the jet cleaning tool supplied Turn the engine off and disconnect from the water supply before clearing a blockage i 14 2 Routine maintenance 14 2 1 Spark plug After every 50 hours of running the spark plug should be removed Check the colour of the deposits on the end of the spark plug it should be a Tan colour Remove all deposits using a stiff brush a brass wire brush is ideal Check the spark plug gap and adjust if required The corre
23. s recommended by the manufacturer Do not use the appliance if a supply cord or important parts are damaged e g safety devices high pressure hoses trigger gun WARNING Incorrect fuels shall not be used as they may prove hazardous WARNING Do not use combustion engine powered appliances indoors unless adequate ventilation is assessed by national labour authorities WARNING Ensure that any exhaust emissions are not in the vicinity of air intakes 7 SAFETY WARNINGS GASOLINE WARNING Use extra care in handling fuels They are flammable and the vapours are explosive The following points must be observed Use only an approved container Never remove the fuel cap or add fuel with the power source running Allow engine exhaust components to cool before refuelling Do not smoke Never refuel the machine indoors Never store the machine or fuel containers inside where is an open flame such as a water heater If fuel is spilled do not attempt to start the power source but move the machine away from the area of spillage before starting Always replace and securely tighten the fuel cap after refuelling fthetank is drained this should be done outdoors 8 SAFETY FEATURES 8 1 Thermal relief valve A thermal relief valve is provided to protect the pump from overloading if the spray gun is closed for an extended length of time or the nozzle becomes plugged However it is intended to be used as a backup system and avoid
24. t flow system After using the detergent facility it should be flushed out thoroughly using copious amounts of water To activate detergent delivery fit the black low pressure nozzle to the end of the lance Submerge the end of the detergent suction tube picture 3 part 24 into your container of pressure washer detergent Suction and mixing will occur automatically as the water flows through the pump 11 OPERATING INSTRUCTIONS 11 1 Pressure washer location Locate the pressure washer on a solid and level surface so that the engine and pump crankcase oil lubricate components properly Avoid areas where puddles are pounded Slippery surfaces can cause injuries Locate the machine in a well ventilated area and away from flammable materials or fumes Be sure ventilation warnings are observed Keep pressure washer at least 18 away from flammable materials Copyright 2013 VARO NV Page 11 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN Locate the machine in a way that the operator has easy access to the pressure washer and its controls Locate the machine so that it is protected from external damage To prevent damage and excessive hose wear locate the pressure washer so that the hose does not cross traffic areas 11 2 Start up procedure Remove all dirt or foreign matter from the gun outlet and the male connector Insert the nozzle into the gun Start engine Warning If the wand is
25. the overheating of the pump Switch the pressure washer OFF if it will not be used for longer than five minutes This reduces wear prevents fuel consumption and extends the live of the pump by avoiding heat 8 2 Safety lock off latch To prevent accidental discharge of high pressure water the safety latch on the trigger should be engaged whenever the pressure washer is not in use refer to operating instruction Copyright 2013 VARO NV Page 6 www varo com GARDENPRO POWERPLUS HIGH QUALITY TOOLS POWXG9007 EN 9 ASSEMBLY INSTRUCTIONS Remove all packaging materials from the unit Check the main unit its components and all accessories for loss and transport damages 9 1 Attach handle and hook Attach the handle picture 1 part 1 and accessory tray picture 1 part 8 to the frame of the pressure washer Insert carriage bolts picture1 part 9 through holes from outside of unit and attach a knob from inside of unit Tighten by hand Fit the lance hook picture 1 part 6 to the upper handle 9 2 Installing the wheels Before you fix the wheels picture 1 part 13 you have to loosen a screw to take out the axle Fit a wheel to the axle and secure using the locking nut provided 9 3 assembly of the bobbin 1 Place the bobbin on the level surface put the water connector into one side of bobbin 2 Tighten its connection by a screw and bolt 3 Connect the high pressure hose picture 1 part 3 to the water c

VARO POWXG9007 high-pressure cleaner

Contents

Download Pdf Manuals

Related Search

Related Contents