AG Neovo RX-32W
Contents
1. 26 Switching input signals gt 26 Adjusting audio volume level 26 Network connection 27 Connecting to a 27 Controlling the display 27 The OSD On Screen Display menu 28 OSD menu overview alate hes 28 Operations the OSD 30 Picture menu el eects 31 Sound 32 Screen 33 SEUNG TSU 36 Product information 39 3 4 Table of Contents Specifications 39 DIMENSIONS uu imisa e To sos 40 Supported input signal 42 Supported PAP input signal combination 44 Troubleshooting 45 Safety warnings and precautions 5 Safety warnings and precautions 4 CAUTION TO REDUCE THE RISK OF ELECTRIC CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral tria2. Screw Type M4 Screw Length 10 mm 10 Parts of the display and their functions 13 Parts of the display and their functions Front Rear panel Receives command signals from the remote control Remote control sensor Detects ambient lighting conditions around the display Ambientlight sensor and adjusts screen brightness automatically when the Power indicator Ambient Light Sensor function is activated Indicates the operating status of the display Lights up green when the power is turned on Lights up red when the display is turned off Lights up red when the display is in Power Save High mode Flashes red when the display is in Power Save Low mode Off when the main power is turned off 9 ENTER VIDEO Selects a video source Confirms your selection enters a submenu the On Screen Display OSD menu MENU Opens or closes the OSD menu 7 Scrolls through settings and options in the OSD menu 4 Hot keys for audio volume adjustment Power button Turns the display on or off 14 Parts of the display and their functions 9 Power indicator Indicates the power status of the display Lights up green when the power is turned on Lights up red when the display is turned off Lights up red when the display is in P
3. Backlight Contrast Brightness Chroma Picture Phase Sharpness Color Temp Noise Reduction Film Mode Reset See page 31 Sound Mode Treble Bass Balance Sound Surround Speaker Audio Source Reset 32 PAP Setting Display Wall Screen Aspect Adjust Screen Freeze 33 The OSD On Screen Display menu 29 Language Schedule Power Save Control Setting Network Settings ae Set Monitor ID HDMI Control Advanced Information All Reset Some options are only available when a certain input signal source is selected 30 The OSD On Screen Display menu Operations in the OSD menu Using the control panel buttons 1 Press MENU to open the OSD menu ENTER 6 VIDEO MENU SOURCE Using the remote control 1 Press MENU to open the OSD menu VOL 2 the OSD menu press to select item 00 O VIDEO SOURCE 2 Press or to select item 5 gt _ 3 Press ENTER VIDEO SOURCE to confirm selections Shoooce VIDEO MENU SOURCE 3 Press ENTER to confirm selections e 4 Press gt or to select a feature and press 4 or gt to adjust settings Press ENTER VIDEO SOURCE to save
4. 4 gt Move ENTER WAG EXIT Exit Language Sets your preferred language for the OSD menu Schedule Date and Time Sets the current date and time Clock Display Sets whether to show the current time which was set e On Off Timer Sets when to turn on or off the display Set the current time before you set the On Off Timer When schedule settings overlap the Everyday setting takes priority over other weekly settings Power Save Sets the display to enter the power saving mode when there is no signal detected Low All source can enter the power saving mode and wake up the display High All source can enter the power saving mode but only VGA signal can wake up the display or you have to press the power button to wake up the display when other source is connected Off If no source is detected the backlight will continue on Serial can bring any mode out of the power saving status LAN can bring Low mode out of the power saving status The OSD On Screen Display menu 37 Control RS 232C LAN Sets a terminal to control the display Sening IR Passthrough Select it when multiple displays are connected via RS 232C cables Primary Designate the display as the primary unit for remote control operation Only this display will be operated by the remote control Secondary Designate the display as the secondary unit The display can not be opera
5. Always ensure that the batteries are inserted with the positive and negative terminals in the correct direction as shown in the battery compartment Different types of batteries have different characteristics Do not mix different types Do not mix old and new batteries Mixing old and new batteries will shorten battery life or cause chemical leaks from the old batteries When batteries fail to function replace them immediately Chemicals which leak from batteries may cause skin irritation If any chemical matter seeps out of the batteries wipe it up immediately using a dry cloth and replace the batteries as soon as possible Due to varying storage conditions the battery life for the batteries included with your product may be shortened Replace them within 3 months or as soon as you can after initial use Important safety instructions 9 There may be local restrictions on the disposal or recycling of batteries Consult your local regulations or waste disposal provider 10 Package contents Package contents Open the sales package and check the contents If any item is missing or damaged please contact your dealer immediately LCD display Power cord Remote control gt G AAA batteries CD The type of power cord supplied may differ from that illustrated depending on your region of purchase Before discarding the package check that you haven t left any accessor
6. long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped Notes on the LCD panel of this display The Liquid Crystal Display LCD panel of this display has a very thin protective layer of glass which is liable to marking or scratching and cracking if struck or pressured The liquid crystal substrate is also liable to damage under excessive force or extreme temperatures Please handle with care The response time and brightness of the LCD panel may vary with the ambient temperature Avoid placing the display in direct sun or where direct sun or spot lighting will shine onto the LCD panel as the heat may damage the panel and the external casing of the display and the bright light will make viewing the display more difficult than necessary The LCD panel consists of individual pixels to display images and is manufactured according to the design specifications While 99 9 of these pixels work normally 0 01 of the pixels may remain constantly lit in red blue Important safety instructions or green or unlit This is a technical limitation of the LCD technology and is defect LCD screens like plasma PDP and
7. conventional CRT Cathode Ray Tube screens are also susceptible to screen burn in or image retention which be found on the screen as visible fixed lines and shades To avoid such damage to the screen avoid displaying still images like On Screen Display menus TV station logos fixed inactive text or icons for more than two hours Change the aspect ratio from time to time Fill the entire screen with the image and eliminate the black bars whenever possible Avoid displaying images in 4 3 aspect ratio over a long period of time otherwise there may be visible burn marks on the screen as two vertical lines Note Under certain circumstances condensation may occur the inner side of the cover glass it s a natural phenomenon and will not affect the operation of the display This condensation will usually disappear after around 2 hours of normal operation Safety notice for remote control Do not put the remote control in the direct heat humidity and avoid fire Do not drop the remote control Do not expose the remote control to water or moisture Failure to do so could result in malfunction Confirm there is no object between the remote control and the remote sensor of the product When the remote control will not be used for an extended period remove the batteries Battery safety notice The use of the wrong type of batteries may cause chemical leaks or explosion Please note the following
8. display as shown in the illustration 200mm 5 Install the wall mounting bracket on the display and attach the display to the wall according to the mounting bracket s instructions The Thickness of the length of the screw should LCD display wall mounting exceed the thickness of the wall mounting bracket by at least 10 mm Make sure that all screws are tightened and secured properly Recommended torque 470 635Necm The mounting means should be strong enough to bear the weight of the display bracket 12 Setting up the display To maintain proper ventilation keep at least 10 mm 10mm of clear space from the back cover of the display to 039 o the wall Please consult a professional technician for wall mount installations The manufacturer accepts no liability for installations not performed by a professional technician The AC IN OUT socket should be on top of connectors when rotating your display Installing the optional desktop stands 1 Place a clean dry and lint free cloth on a flat horizontal and object free sur face Make sure that the size of the cloth is larger than the display 2 Gently lay the display on the cloth with the LCD screen facing down 3 Place the desktop stands on the RX 32 display as illustrated 4 Use the screws and a suitable screwdriver to secure the stands on the display
9. 72Hz 640 480 75Hz 720 400 70Hz 800 600 60Hz 800 600 75Hz 1024 768 60Hz 1024 768 75Hz 1280 768 60Hz 1280 800 60Hz RB 1280 x 800 60Hz 1280 960 60Hz 1280 x 1024 60Hz 1360 x 768 60Hz 1366 768 60Hz 1400 x 1050 60Hz 1600 x 1200 60Hz 1680 1050 60Hz RB 1600 x 1050 60Hz 1920 x 1080 60Hz OO O OO O O OO O NTSC M NTSC J PAL BDGHI 576i 50 2 480i 60Hz 480p 60Hz 576p 50Hz 720p 50Hz 720p 60Hz Product information 43 1080i 50Hz 1080i 60Hz 1080p 50Hz 1080p 60Hz cr supported Blank not supported Product information 44 Supported PAP input signal combination O O O O O O O O O O O O x O O O O O x O O O O O O O O O O O O O O O O O O O Troubleshooting 45 Troubleshooting No picture Check the following Is the display turned on
10. Check the power indicator of the display Is the signal source device turned on Turn on the device and try again Are there any loose cable connections Make sure that all cables are connected firmly Have you chosen an unsupported output resolution on the computer Refer to Supported input signal resolution on page 42 to select a supported resolution and try again Have you chosen an unsupported output resolution on the DVD or Blu ray disc player Refer to Supported input signal resolution on page 42 to select a supported resolution and try again No sound Check the following Have you turned on the mute function on the display or the input source device Turn off the mute function or increase the audio volume level and try again Are there any loose cable connections Make sure that all cables are connected firmly The computer input image looks strange Have you chosen an unsupported output resolution on the computer Refer to Supported input signal resolution on page 42 to select a supported resolution and try again Use the Auto Adjustment function Refer to Adjust Screen on page 35 to let the display automatically optimize the display of computer image If the result of the Auto Adjustment function is not satisfactory use the Clock Frequency Phase H Position and V Position functions to manually adjust the image The control panel buttons do not work Have yo
11. RAN _ THE DISPLAY CHOICE 9 V OF PROFESSIONALS RX 32 amp RX 42 Security LED Backlit Display U se r M a n Table of Contents Table of Contents Safety warnings and precautions 5 Important safety instructions 7 Notes the LCD panel of this 7 Safety notice for remote control 8 Battery safety notice 8 Package contents 10 Optional accessory 10 Setting up the display 11 Mounting the display 11 Parts of the display and their functions 13 Front Rear 13 Input output terminals 15 Remote control 17 Using the remote control 18 Connection 19 Connecting audio video signals 19 Connecting 25 Basic operations 26 Turning the display on or 26 Locking unlocking the controls
12. al Reset Resets all settings in the Picture menu 32 The OSD On Screen Display menu Sound menu Sound Mode Standard Treble 0 Bass 0 Balance Center Surround Off Speaker Internal Audio Source Audio in Reset 4 Enter 5 Exit Sound Mode Adjusts the sound output from the speakers Dynamic Enhances treble and bass Standard Flat settings Custom Recalls the customized settings Treble Adjusts the audio treble Bass Adjusts the audio bass Balance Adjusts the audio balance Surround Turns the surround mode on or off Speaker Sets the audio source Line Out Selects the audio output source from AUDIO OUT R L on the rear connector panel External Selects the audio output source from SPEAKERS RIL on the rear connector panel Internal Select the audio output source from the internal speakers Audio Sets the audio input source Source HDMI 2 Reset Resets all settings in the Sound menu The OSD On Screen Display menu 33 Screen menu Screen PAP Setting Display Wall Aspect Adjust Screen Freeze PAP Setting PAP Turns on or off the PIP Picture in Picture and PBP Picture Picture and by Picture functions Picture Active Picture For the PIP selects the main or sub picture to operate For the PBP selects the left or right picture to operate Swaps the main sub or left right
13. changes So VIDEO MENU SOURCE 4 Press and to select feature and press 4 or to adjust settings Press ENTER to confirm changes 5 Press MENU to close the OSD menu ENTER MENU SOURCE 5 Press MENU to close the OSD menu 5 The OSD On Screen Display menu 31 Picture menu Picture Picture Mode Standard Backlight 100 Contrast 50 Brightness 50 Chroma 25 Phase 25 Sharpness 10 Color Temp Noise Reduction Film Mode Reset Picture Mode Sets the display mode Backlight Adjusts the backlight intensity for the screen T feature is not available if the Ambient Light Sensor or AC function is set to On Contrast Adjusts the image contrast Brightness Adjusts the image brightness Chroma Adjusts the color intensity of the image Phase Adjusts the color tint of the image Sharpness Adjusts the image sharpness Color Temp Adjusts the color temperature Noise Reduces electrical image noise caused by different media players Reduction Film Mode Optimizes the screen display automatically by detecting picture content and applying a reverse 3 2 or 2 2 pull down process The picture will be clearer and more natural This function is not available when displaying Picture and Picture This function may not be correctly processed depending on the input sign
14. e remote control Controlling the display Once you have the correct IP address for your display and the display is on or in standby mode you can use any computer that is on the same local area network to control the display You cannot control the display via the RS 232C connector when LAN control is in use It is recommended that you use Internet Explorer versions 7 0 or higher browser 1 Enter the IP address of the display in the address bar of your browser and press Enter 2 The setting page appears Information Shows information of the display It is for information only There are no items that can be set Picture 8 Sound Provides options for picture and sound adjustments Screen Provides options related to display adjustments Setting Provides options for advanced display adjustments Mail Report Provides options for setting up email accounts to receive status or error reports sent from the display Network Provides options for manually setting the display s IP address or obtaining an IP address from a DHCP server Provides options for setting or changing the user name and password to secure this network control system Make sure the Setting gt Control Setting menu is to LAN if you would like to turn on the display from a web page 28 The OSD On Screen Display menu The OSD On Screen Display menu OSD menu overview Menu name Options functions Picture Mode
15. eeded connect the computer s audio output jack to the AUDIO IN AUDIO1 jack the display using a suitable audio cable 3 To view video image from this input press the DVI or DP HDMI 1 HDMI 2 button on the remote control DisplayPort cable HDMI SDI cable cable Audio cable DVI D cable DVI D to HDMI SDI device conversion cable Computer The cables are not supplied and should be purchased separately Connection 21 Connecting the YPbPr component video input 1 Connect the VIDEO IN YPbPr jacks on the display to the component output jacks on an A V device such as a VCR or DVD player using a component video cable 2 Connect the DVD player s audio output jacks to the AUDIO IN AUDIO2 jacks on the display using a suitable audio cable 3 To view video image from this input press the YPbPr button on the remote control Component video cable Audio cable DVD player VCR The cables are not supplied and should be purchased separately 22 Connection Connecting the AV and S Video inputs 1 Connect the VIDEO IN S VIDEO or AV IN jack on the display to the output jack on an A V device such as a VCR using an appropriate video cable 2 Connect the VCR s audio output jacks to the AUDIO IN jacks on the display using a suitable audio cable 3 To view video image from this i
16. ies inside the box Dispose of packaging materials wisely You can recycle the cardboard carton Consider storing the package if possible for future transport of the display Do not leave plastic bags within reach of young children or babies Optional accessory In addition to the items that come with the standard package the following optional accessory is also available separately RX 42 Desktop stand Setting up the display 11 Setting up the display Mounting the display You can install the display on a vertical surface with a suitable wall mounting bracket or on a horizontal surface with the optional desktop stands Please pay attention to the following notes during installation This display should be installed by at least two adult persons Attempting to install this display by only one person may result in danger and injuries Refer the installation to qualified technicians Improper installation may cause the display to fall or malfunction Installing the display on a wall 1 Place clean dry and lint free cloth a flat horizontal and object free sur face Make sure that the size of the cloth is larger than the display 2 Gently lay the display on the cloth with the LCD screen facing down 3 Remove the desktop stands from the display if installed 4 Identify the wall mounting screw holes the back 400mm the
17. ing desktop stands is required before use Important safety instructions 7 safety instructions Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When cart is used use caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for
18. ngle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons A The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance THIS EQUIPMENT MUST BE GROUNDED To ensure safe operation the three pin plug must be inserted only into a standard three pin power outlet which is effectively grounded through normal household wiring Extension cords used with the equipment must have three cores and be correctly wired to provide connection to the ground Wrongly wired extension cords are a major cause of fatalities The fact that the equipment operates satisfactorily does not imply that the power outlet is grounded or that the installation is completely safe For your safety if you are in any doubt about the effective grounding of the power outlet please consult a qualified electrician The mains plug of the power supply cord shall remain readily operable The AC receptacle mains socket outlet shall be installed near the equipment and shall be easily accessible To completely disconnect this equipment from the AC mains disconnect the power cord plug from the AC receptacle Do not place this display an uneven sloping
19. nput press the AV button on the remote control for the AV signal or press the INPUT button repeatedly for the S Video signal e S Video cable AV cable Audio cable DVD player VCR The cables are not supplied and should be purchased separately Connection 23 Connecting external speakers The built in amplifier on the display allows you to output audio signals through external speakers Connect external speakers to the SPEAKERS RIL jacks on the display External speakers You can use the remote control or the control panel on the display to adjust the volume 24 Connection Connecting multiple displays You can connect multiple displays serially daisy chain to a computer for management The number of displays you can connect serially depends on the resolution of the input signal you use Additional display e 6 e RS 232C DVI AV D Sub 15 SDI cable cable cable pin cable cable ee The first display c This RS 232C daisy chain application requires RS 232C port equipped computer Avoid using HDCP source for daisy chain application Connection 25 Connecting power Plug one end of the power cord into the AC IN jack on the display and the other end into an appropriate power outlet if the outlet is switched turn on the switch 2 Press the power switch to turn on the main power The supplied power cord is suitable for
20. oduct specifications for models recommended for portrait orientation Landscape only models operated in portrait mode may result in premature failure and will not be covered under the warranty OSD Info Box When turned On switching signal inputs or changing timing the display will show the current input source and resolution onscreen Select Off to show the information box onscreen only when you press INFO on the remote control AC Turns the AC function on or off This feature enhances image contrast for dark scenes C7 This feature is not available if the Ambient Light Sensor function is set to On Ambient Light Sensor When turned On the image brightness will adjust automatically as the ambient lighting conditions change Information Displays the following information of your display Date Model Name Serial Number Operating Time Software Version LAN Version IP Address All Reset Returns all settings to factory default values Product information 39 Product information Specifications Specifications Active area Pixel pitch mm 0 3637 x 0 3637 0 4833 x 0 4833 1920 0 LCD panel Brightness cd m2 350 400 typical Contrast typical 3000 1 1000 1 Adaptive contrast 14700 1 33500 1 ee time ms 6 5 9 Video DVI DVI D Composite Video BNC jack S impel Video YPbPr RCA jacks HDMI 2 Dis
21. onds Once locked the control panel buttons do not function unless unlocked Remote control functions To lock unlock the remote control functions press and hold MENU and for5 seconds Once locked the display does not respond to any remote control operations unless unlocked Switching input signals Press the INPUT button or those signal selection buttons on the remote control or the INPUT button on the control panel to select an input signal Adjusting audio volume level Press lt gt the control panel VOL VOL on the remote control to adjust the volume Network connection 27 Network connection Connecting to a LAN To set the display to connect to a local area network 1 Connect a RJ45 cable to the corresponding ports on the display and your LAN switch or router 2 Enter the OSD menu Setting gt Control Setting Select LAN 3 Enter the next OSD menu Setting gt Network Settings If you are DHCP environment select DHCP gt Execute and press ENTER Once done the IP Address Subnet mask Default gateway Primary DNS and Secondary DNS settings will be displayed If you are not in a DHCP environment select Manual gt Execute and press ENTER Contact your ITS administrator for information on the IP Address Subnet mask Default gateway Primary DNS and Secondary DNS settings and enter it accordingly 4 To save the settings and return to the previous menu highlight Execute and press ENTER on th
22. or unstable surface such as trolley where it may fall and cause damage to itself or others Do not place this display near water like a spa or pool or in a position which will allow the splashing or spraying of water onto the display like in front of an open window where rain water may enter Do not install this display in a confined space without proper ventilation and air circulation such as in a closed cabinet Allow proper space around the display for dissipating heat inside Do not block any openings and vents on the display Overheating may result in hazards and electric shock Installation of this display should only be performed by a qualified technician Failure to install this display properly may cause injuries and damages to the personnels and the display itself Check the installation regularly and maintain the display periodically to ensure the best working condition Use only the accessories approved or recommended by the manufacturer to mount this display Using wrong or unsuitable accessories may cause the display to fall and result in serious personal injuries Make sure that the surface and fixing points are strong enough to sustain the weight of the display To reduce the risk of electric shock do not remove covers No user serviceable parts inside Refer servicing to qualified service personnel 6 Safety warnings and precautions To prevent personal injuries mounting the display or install
23. ource in 4 3 aspect ratio Full 1 Enlarges the picture to fill the screen the vertical direction keeping the same aspect ratio A black frame may appear around the picture Full 2 Enlarges the picture to fill the screen Real Displays the picture in its original number of dots For video signal inputs 4 3 original source 16 9 Original source O Q Wide Zoom Wide Zoom A 4 Zoom Zoom S Full Full O e O O 4 3 4 3 ewe The OSD On Screen Display menu 35 Aspect continued For PC signal input Real Full 1 Full 2 Adjust Screen Auto Adjustment Sets whether to optimize image display for each VGA input Phase Adjusts the phase of the VGA input image Clock Frequency Adjusts the clock frequency of the VGA input image Position Adjusts the horizontal position of the VGA input image Position Adjusts the vertical position of the VGA input image Freeze Freezes the displayed image 36 The OSD On Screen Display menu Setting menu Setting Language English Schedule Power Save High as 25 Control Setting RS 232C Network Settings Set Monitor ID 01 HDMI Control Off Advanced Information All Reset
24. ower Save High mode Flashes red when the display is in Power Save Low mode Off when the main power is turned off Parts of the display and their functions 15 input output terminals 860008 RJ 45 Connects to the RJ 45 port on your Ethernet or router RS232C IN OUT For external control and multi display operation RS232C IN receives control signals from a computer or another display 5232 OUT outputs control signals from the RS232C IN input to another display DISPLAY PORT Connects to a DisplayPort compatible device DVI OUT Outputs DVI signals from the DVI IN to another display DVI IN Receives DVI signals from an external device such as a computer HDMI 1 HDMI 2 Receives HDMI signals from an external device such as a Blu ray disc player VIDEO YPbPr Receives component video YPbPr signals from an external device such as a DVD player HDTV device or Laser disc player 9 8 8 oo ooo VIDEO IN S Receives S Video signals from an external device such as a VIDEO VCR or DVD player AV OUT Outputs composite video signals from the AV IN input to another display AV IN Receives composite video signals from an external device such as a VCR or DVD player VGA OUT Outputs analog RGB signals from the VGA IN inpu
25. pictures Picture Size PIP only Changes the size of the sub picture Picture Position PIP only Changes the position of the sub picture cr This feature is not available for Video and S Video inputs PAP is not available for all signal source combinations See Supported PAP input signal combination on page 44 for more information on supported combinations In PAP mode only sound from the active picture will be available Display Wall H Monitors V Monitors Sets the number of displays used in the horizontal vertical direction H Position V Position Sets the horizontal vertical position of the display wall matrix Frame Comp Adjusts images near the display edges for optimal demonstration across the display wall LED Turns the power indicator on the display on or off Power On Delay Choose to enable or disable a sequence in turning on the screen matrix If enabled the display will turn on one horizontal matrix starting from the top row 34 The OSD On Screen Display menu Aspect Sets the picture s aspect ratio Wide Zoom Enlarges to fill screen with minimum distortion Zoom Enlarges the picture keeping the same aspect ratio Full Enlarges the picture horizontally to fill the screen when the picture source is 4 3 Standard definition When the picture source is 16 9 High definition it displays in the same 16 9 aspect ratio 4 3 Displays all picture s
26. playPort Audio L R RCA jacks Line in 3 5 mm jack Control RIAS Jack RJ45 WILED I computer Video DVI DVI D Composite Video BNC jack Output Speaker 8 Ohms 12W 12W 8 Ohms Audio L R RCA jacks Control RS 232C D Sub 9 pin y TOO IO AC OOOI Power Consumption Max lt ooW gt Consumption Standby lt 0 5W Operating Temperature 0 40 C 32 104 F Operating Humidity 10 90 without condensation Environment Storage Temperature 20 60 C 4 140 F Storage Humidity 10 95 without condensation Display Orientation Landscape Portrat Weight Ibs kg Approximately Approximately Mechanical Dimensions 29 8x178x273 S8 6x226x4 8 W x H x D inch mm 756 6 x 451 1 x 94 8 980 x 574 x 121 Specifications and functions are subject to change without notice 40 Product information Dimensions RX 32 451 1 9 991 8 76 Unit mm 41 Product information RX 42 194 3 7194 3 4 980 932 121 574 478 35 A 235 22 8982233 591 4 Unit mm 42 Product information Supported input signal resolution 640 480 60Hz 640 480
27. remote control from a location closer to display s remote control sensor window Max 10 m 32 8 feet 45 45 Connection 19 Connection Connecting audio video signals Pay attention to the following notes when you connect cables Please turn off all devices Familiarize yourself with the audio video ports on the display and the devices you want to use Be aware that incorrect connections may adversely affect picture quality Do not remove cables from the ports by pulling the cable itself Always grasp and pull the connectors at the end of the cable Ensure that all cables are fully inserted and firmly seated Connecting the VGA input Connect the VGA IN jack on the display to the VGA output jack on a computer using a D Sub 15 pin cable 2 Connect the computer s audio output jack to the AUDIO IN AUDIO jack on the display using a suitable audio cable 3 To view images from this input press the VGA button on the remote control D Sub 15 pin cable Audio cable Ti Computer The audio cable is not supplied and should be purchased separately 20 Connection Connecting the digital input 1 Connect the DVI IN DISPLAY PORT HDMI 1 HDMI 2 SDI jack on the display to the DVI D DisplayPort HDMI output jack on a computer or equipment using a DVI D DisplayPort HDMI SDI or a DVI D to HDMI conversion cable 2 If n
28. t source buttons when the OSD menu is off SDI and MULTI MEDIA functions are not available with this display MENU Opens or closes the OSD menu Numeric button 0 MUTE Performs as a numeric button when the OSD menu is on Turns on or off the mute function Scrolls through settings and options in the OSD menu MULTI MEDIA buttons These functions are not available with the display 18 Parts of the display and their functions Using the remote control Installing remote control batteries 1 Open the remote control battery compartment cover 2 Insert the supplied batteries ensuring that the positive and negative marked battery terminals match the and marks in the battery compartment C The supplied batteries are provided for your convenience so that you can operate the display straight away You should replace them as soon as possible 3 Refit the battery compartment cover Remote control usage tips Point and aim the top front of the remote control directly at the display s remote control sensor window when you press the buttons Do not let the remote control become wet or place it in humid environments like bathrooms If the display s remote control sensor window is exposed to direct sunlight strong light the remote control may not operate properly In this situation change the light source readjust the angle of the display or operate the
29. t to another display VGA IN Receives analog RGB signals from an external device such as a computer Parts of the display and their functions AUDIO IN Receives audio signals from an external device such as a AUDIO1 computer AUDIO IN Receives audio signals from an external device such as a AUDIO2 VCR or DVD player AUDIO OUT RIL Outputs audio signals to an external device SPEAKERS RIL Outputs audio signals to external speakers AC SWITCH ON OFF Turns on or off the main power AC IN Connects to a power outlet via the supplied power cord AC OUT Relays the AC power from the AC IN jack to another display SDI in SDI out Connects SDI cables for SDI input output signal Available in HD SDI models Parts of the display and their functions 17 Remote control T cat YPbPr gt MULTI MEDIA MUT ON OFF Turns the display on or off INPUT Selects an input source EXIT Returns to a previous menu or closes the OSD menu lt VOL gt VOL Scrolls through settings and options in the OSD menu Turns down up the volume ENTER Confirms your selection or save changes INFo Shows the current input source and resolution Numeric buttons 1 9 Input source buttons Performs as numeric buttons when the OSD menu is on Performs as inpu
30. ted by the remote control and will only receive the control signal from the primary display via the RS 232 connection Network See Network connection on page 27 for details Settings Set Monitor Assigns an ID number for the current display when multiple displays are ID connected For use when under the RS 232C control mode HDMI Uses the HDMI CEC Consumer Electronics Control industry standard Control protocol to share functionality between connected devices and the display To transfer system commands you need to use an HDMI cable to connect the display to a device equipped with HDMI CEC Select On in this menu and you can operate the main functionalities on your display and the connected device with one remote control 38 The OSD On Screen Display menu Advanced Auto Search Automatically detects available input sources Auto Adjustment Automatically optimizes image display for the VGA input Overscan Turns the overscan function on or off RGB Signal Sets the type of signal for a piece of video equipment or PC connected to the HDMI of the display Anti Burn In Turns Anti Burn In function on or off When turned on you can select a mode to perform and a time interval to activate the function Mode A ps frame Executes fast Mode B ps line Slower but more precise than mode A Mode C ps dot Slowest but the most precise mode OSD Rotation Adjusts the OSD rotation see pr
31. u locked the control panel buttons Unlock the buttons and try again 46 Troubleshooting The remote control Have you locked the remote control function Unlock does not work the function and try again Check for incorrect battery orientation Check for dead batteries Check your distance and angle from the display Check whether remote control is properly being pointed at the display s remote control sensor window Check for any obstacle between the remote control and the remote control sensor window Check that the remote control sensor window is not under strong fluorescent lighting or in direct sunlight Check for any devices computer or personal digital assistant PDA nearby that transmit infrared signals which may cause interference to signal transmission between the remote control and the display Turn off the infrared function of these devices Company Address 5F 1 No 3 1 Park Street Nangang District Taipei 11503 Taiwan
32. use with 110 240V AC power only The power and outlet illustrated may differ from the ones used in your region Only use an appropriate power cord for your region Never use a power cord which appears damaged or frayed or change the plug type on the power cord aware of the power loading when you use extension cords or multiple outlet power oards There no user serviceable parts in this display Never unscrew or remove covers There are dangerous voltages inside the display Turn off the power and unplug the power cord if you intend to move the display 26 Basic operations Basic operations Turning the display on or off To turn on or off the display press the power button on the display s control panel or on the remote control TD 22 no The display s standby mode still consumes power To completely cut off power supply disconnect the power cord from the power outlet The display follows the VESA approved DPM Power Management function The power management function is an energy saving feature that automatically reduces the display s power consumption when the keyboard or the mouse has not been used for a fixed period Locking unlocking the controls You can lock unlock the control panel to prevent unwanted or accidental operations Control panel buttons lock unlock the control panel buttons press and hold 4 and simultaneously for 5 sec
Download Pdf Manuals
Related Search