Makita 9046 power sander
Contents
1. for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source and or the battery pack from the power tool before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally 19 Store idle power tools out of the reach of chil dren and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users 20 Maintain power tools Check for misalignment or binding of moving parts breakage of parts and any other condition that may affect the power tools operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools 21 Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control 22 Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working con ditions and the work to be performed Use of the power tool for operations different from those intended could result in a hazardous situation Service 23 Hav2. the same voltage as indicated on the nameplate and can only be operated on single phase AC supply They are double insulated in accordance with European Standard and can therefore also be used from sockets without earth wire For European countries only Noise and Vibration The typical A weighted sound pressure level is 80 dB A Uncertainty is 3 dB A The noise level under working may exceed 85 dB A Wear ear protection The typical weighted root mean square acceleration value is not more than 2 5 m s These values have been obtained according to EN60745 EC DECLARATION OF CONFORMITY We declare under our sole responsibility that this product is in compliance with the following standards of stand ardized documents EN60745 EN55014 EN61000 in accordance with Council Directives 89 336 EEC 98 37 EC Yasuhiko Kanzaki CE 2005 A Director MAKITA INTERNATIONAL EUROPE LTD Michigan Drive Tongwell Milton Keynes Bucks MK15 8JD ENGLAND Responsible manufacturer Makita Corporation Anjo Aichi Japan GENERAL SAFETY RULES A WARNING Read all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious injury The term power tool in all of the warnings listed below refers to your mains operated corded power tool or battery operated cordless power tool SAVE THESE INSTRUCTIONS Work area safety 1 Keep work area clean and well lit Clut
3. 743 Then press the upper part of the front fixing cardboard in arrow direction to hook it onto the claws 1 Claws 2 Upper part Insert the notch of the paper dust bag into the guide of the paper dust bag holder Then install the paper dust bag holder set on the tool NOTE e f you connect a Makita dust collector to this tool more efficient and cleaner operations can be performed 1 Notch 2 Guide 003745 003331 Sanding operation Z CAUTION e Never run the tool without the abrasive paper You may seriously damage the pad e Do not block motor vent with your finger or hand e Never force the tool Excessive pressure may decrease the sanding efficiency damage the abrasive paper or shorten tool life Hold the tool firmly Turn the tool on and wait until it attains full speed Then gently place the tool on the workpiece surface Keep the pad flush with the workpiece and apply slight pressure on the tool MAINTENANCE A CAUTION e Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance To maintain product SAFETY and RELIABILITY repairs carbon brush inspec tion and replacement any other maintenance or adjustment should be per formed by Makita Authorized Service Centers always using Makita replacement parts ACCESSORIES Z CAUTION e These accessories or attachments are recommended for use with your Makita tool specified in this manual Th
4. HSITSNA Taa kita Orbital Sander MODEL 9046 003270 DOUBLE INSULATION INSTRUCTION MANUAL A WARNING For your personal safety READ and UNDERSTAND before using SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE SPECIFICATIONS Model 9046 Pad size 115 mm x 229 mm Abrasive paper size 115 mm x 280 mm Orbits per minute min 6 000 Overall length 283 mm Net weight 3 0 kg Safety class gu e Due to our continuing programme of research and development the specifications herein are subject to change without notice e Note Specifications may differ from country to country SYMBOLS END201 2 The following show the symbols used for the equipment Be sure that you understand their meaning before use Cli pieces eames Read instruction manual DOUBLE INSULATION EE EAR Only for EU countries Do not dispose of electric equipment together with household waste material In observance of European Directive 2002 96 EC on waste electric and electronic equipment and its implementation in accordance with national law electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility Intended use The tool is intended for the sanding of large surface of wood plastic and metal materials as well as painted sur faces Power supply The tool should be connected only to a power supply of
5. e use of any other accessories or attachments might present a risk of injury to persons Only use accessory or attachment for its stated purpose If you need any assistance for more details regarding these accessories ask your local Makita service center e Abrasive paper with pre punched holes e Joint 25 for connecting to vacuum cleaner e Velcro type of abrasive paper e Paper dust bag with pre punched holes e Paper dust bag holder Makita Corporation Anjo Aichi Japan 883989E221
6. e your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained 24 Follow instruction for lubricating and changing accessories 25 Keep handles dry clean and free from oil and grease GEB021 1 Specific Safety Rules DO NOT let comfort or familiarity with product gained from repeated use replace strict adherence to sander safety rules If you use this tool unsafely or incorrectly you can suffer serious personal injury 1 Hold power tools by insulated gripping sur faces when performing an operation where the cutting tool may contact hidden wiring or its own cord Contact with a live wire will make exposed metal parts of the tool live and shock the operator 2 Always use Safety glasses or goggles Ordinary eye or sun glasses are NOT safety glasses 3 Hold the tool firmly 4 Do not leave the tool running Operate the tool only when hand held 5 This tool has not been waterproofed so do not use water on the workpiece surface 6 Ventilate your work area adequately when you perform sanding operations 7 Some material contains chemicals which may be toxic Take caution to prevent dust inhala tion and skin contact Follow material supplier safety data 8 Use of this tool to sand some products paints and wood could expose user to dust containing hazardous substances Use appropriate respi ratory protectio
7. ise Insert the paper end into the clamper aligning the holes in the paper with those in the pad Then return the clamp lever to the original position to secure the paper Repeat the same process for the other end of the tool maintaining the proper paper tension 003309 004435 Velcro type of abrasive paper Pad 003317 aoRoOn a X Mark Mark Dust bag Entry port Dust spout 003742 Groove Front fixing cardboard Front side of paper dust bag For the velcro type of abrasive paper accessory Remove all dirt or foreign matter from the pad Attach the paper to the pad aligning the holes in the paper with those in the pad A CAUTION e Always use velcro type of abrasive papers Never use pressure sensitive abrasive papers Dust bag To install the dust bag align the gt mark on the bag s entry port with the K mark on the dust spout of the tool and fit the entry port onto the dust spout Then turn the dust bag clockwise to secure it in place For the best results empty the dust bag when it becomes approximately half full tapping it lightly to remove as much dust as possible To remove the dust bag follow the installation procedures in reverse Installing paper dust bag optional accessory Place the paper dust bag on the paper dust bag holder with its front side upward Insert the front fixing cardboard of the paper dust bag into the groove of the paper dust bag holder 003
8. n 9 Be sure that there are no cracks or breakage on the pad before use Cracks or breakage may cause a personal injury SAVE THESE INSTRUCTIONS A WARNING MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury FUNCTIONAL DESCRIPTION 003280 1 Lock button 2 Switch trigger 003295 1 Front grip ASSEMBLY 003307 1 Conventional type of abrasive paper 2 Clamp lever 3 Pad Z CAUTION e Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool Switch action Z CAUTION e Before plugging in the tool always check to see that the switch trigger actuates properly and returns to the OFF position when released To start the tool simply pull the switch trigger Release the switch trigger to stop For continuous operation pull the switch trigger and then push in the lock but ton To stop the tool from the locked position pull the switch trigger fully then release it Front grip The front grip position can be changed in 90 increments Pull the front grip and rotate it to the desired position A CAUTION e Always be sure that the tool is switched off and unplugged before carrying out any work on the tool Installing or removing abrasive paper For conventional type of abrasive paper with pre punched holes standard equipment Turn the clamp lever counterclockw
9. ohol or medication A 10 11 12 13 14 15 GEA001 3 moment of inattention while operating power tools may result in serious personal injury Use safety equipment Always wear eye protec tion Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used for appropriate conditions will reduce personal inju ries Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plug ging in power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and bal ance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts If devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards Power tool use and care 16 17 Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate
10. tered and dark areas invite accidents Do not operate power tools in explosive atmos pheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders away while oper ating a power tool Distractions can cause you to lose control Electrical safety 4 Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet condi tions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock Personal safety 9 Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alc
Download Pdf Manuals
Related Search