Fte maximal TSF 310 CI
Contents
1. With mediaMAX EVO mediaMAX MINI field strength meter you can carry out the programming of all the modules consecutively as long as they are interconnected with each other through the RJ 45 cable supplied with each unit Through PRO 201 the programming is made module by module TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 Cl 1 4 2 Programming Below you will find the steps to follow in order to make the programming both from corresponding EVO and MINI field strength meter as well as from PRO 201 mediaMAX EVO mediaMAX MINI In order to start programming the TSF 310 Cl transmodulator you will have to go to Tools option through the key 8 of your field strength meter and to select the Transmodulator Prog option Then it will proceed to recognize the module and to show the main menu In the Transmodulator Prog are shown the different configuration options that this tool offers 1 Select Device The field strength meter allows carrying out the programming of one or several transmodulators from an only transmodulator Without interconnection of modules An only module connected Interconnection of several modules you can select which module you wish to program 4 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI If you have a module with a serial number higher than 075511441882 it will allow you to choose between two units with an only de2. CAM Reset It allows making a reset in the CAM Watchdog CAM In cases where the encoded services stop working you can use one of the following options Deactivate No actions will me made in the CAM Update When it is detected that the decryption of the CAM has been lost the rights will be sent systematically until the decryption gets back Reset As soon as the loss of decryption of the CAM is detected a reset will be made Both Once the loss of decryption of the CAM is detected the rights will be sent several times until the decryption gets back In cases where it does not get back the module will make a reset of the CAM CAM Reset after It makes a reset of the CAM alter a set period of time Options 0 5 min 10 min 15 min PRO 201 A When you connect the PRO 201 programmer it will proceed to recognize the module and to show the main menu In the main menu are shown the different options for configuring the transmodulator Note From PRO 201 programmer you can only carry out the programming of a single module in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter We have to use the Up and Down buttons of the keyboard in order to move to the different options and to get into the submenus we have to press OK button 11 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 Cl 1 Ma
3. 1 Select the option Add services through Up Down buttons Press OK to continue Delete Services ESE u al BW usage gt Delete services Add services 083 1 Select the option Delete services through Up Down buttons Press OK to continue A TEF 1O CT Inpue OS 2 PID 06200 arte HD Add 2 Select one of the transponder services you want to add through Left Right keys and select the Add button to include the service in the multiplex TSE AE RES fake tte GER PTD 06000 Das Erste Rem A 2 Select the service you want to delete with the Left Right keys Then press OK over Rem in order to remove it or press OK over All in order to delete all the services of the multiplex 14 TSF 310 Cl Tor ST Operation finish 3 A window will appear and it will let you know that the operation made has been correct Tor Sie Operation finish 3 A window will appear and it will let you know that the operation made has been correct Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services version_en_2 0 FTE maximal User s manual TSF 310 CI LCN The LNC function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LNC support to make the ordination of
4. Fle TSF 310 Cl USER S MANUAL User s manual TSF 310 CI NOTE This user s guide is adapted to software version v 0 1 26 of TSF 310 Cl dated 25 11 2011 For future software updates you can download the users guide from the following website http www ftemaximal com Chapter 1 Installation 1 1 Safety Measures 1 Never place the device next to hot sources 2 Never undergo the device to temperatures that exceed ts level of operation 3 Never expose the device to leakings nor spatterings 4 Never place objects that contain liquids over the device 5 Respect the ventilation slots of the device do not cover them with any kind of object 6 The space around the device must be free of objects in a minimum radius of 40cm 7 Avoid locations with possibilities of spilling liquids on the inside of the device and with important changes of temperature 8 Never open the device by yourself due to electric risk In case of problems go always to qualified technicians 9 Never under no circumstances open the device when connected to the electrical net 10 During the handling it is better to disconnect the device from the electrical net 11 Obey the electricity security rules during the assembling Use materials that obey the current law 12 The connecting plug must be accessible in a fast and simple way to have a fast disconnection 13 Never touch the plug with wet hands Also disconnect always the device before handli
5. Settings This option allows saving and loading the configuration of the module carrying out firmware update or making an adjustment of the time and date of the module Clock Set Date and time Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date Set date time all devices Loading the current date and time of the module in the rest of interconnected modules Alias Write alias It allows you to assign a name alias to the module you are programming Option only available when the Alias Auto option is configures as none manual mode Auto Alias It allows configuring the name alias of the modules automatically Options Channel Frequency Service None Upgrade Send Firmware from USB It allows carrying out the firmware update from the USB device Send firmware to all It allows carrying out the update of all the modules that are interconnected at the same time Configure all devices Input values to all devices It allows copying the current input configuration in all the interconnected modules Modulator values to all devices lt allows copying the configuration of the current modulator in all the interconnected modules Output values to all devices It allows copying the current output configuration in all the interconnected modules Factory default to all devices It allow
6. band amplifier 47 862MHz Mixer Parabolic antenna OS series Mod OS 100 STB Mod AMP 310 P Mod MUX 310 Code 0701105 Code 2003520 Code 2003518 Chapter 2 Technical features Ref TSF 310 Cl Code 2003544 Input frequency margin 950 2150 MHz Input level 25 to 65 dBm Imput impedance 75 LNB feeding conmutation Input connector Input LOOP losses FEC 13V 18V 0 22kHz Female F connector lt 1 dB 1 2 2 3 3 4 5 6 7 8 8 9 9 10 174 173 1 5 2 5 3 5 4 5 DVB RS 204 188 Input modulation QPSK 8PSK Input Symbol Rate DVB S 1 45 MS s DVB S2 1 37 MS s Selectable format of output modulation DVB T DVB H Bandwidth MHz Mode Output channels Output connectors DVB T 6 7 8 DVB H 5 6 7 8 DVB T 2k 8k DVB H 2k 4k 8k C2 C69 Mux 1 C2 C69 Mux 2 Consecutive channel to mux 1 Female F connector Output Level 80 dBuV Regulation margin 15 dB MIX Losses lt 1 dB Band spurious 60 dBc Programming Interface RJ 45 Programmer PRO 201 media Max EVO and media Max MINI Common Interface Yes 2 Slots Operating temperature 0 C 45 C Consumption 5V mA 800 Consumption 12V mA 300 Consumption 24V mA 15 Consumption 30V mA 2 Dimensions 75x265x150 mm Weight 1 4Kg Note This option is available only in devices with a serial number higher than a 075511441882 Chapter 3 Declaration of conformity CONFORMITY DECLARATION WE FTE MAXIMAL DECLARE THAT THE PRODUCT TSF 310 Cl IS IN CONFO
7. signal Options O 15dB Calibration Allows the realization of two tests in order to verify the correct running of the device Deactivate output It allows activating or deactivating the ouput of transmodulator Switch output to CW It allows activating or deactivating the DVB T DVB H modulation allowing visualizing the carrier without modulation in the selected frequency 6 System This option provides information of the transmodulator System logfile In this field are indicated the registered events in the module Read log It allows reading the registered events in the module Clear log It allows deleting all events stored until this moment Export log to USB It allows you to export all events registered to the connected USB device 6 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI NM low Limit dB An event of error will be recorded when the value of Noise Margin is lower than the set value NM hight limit dB Once the event of error is recorded Noise Margin lt Limit Lower NM this will be Noise Margin value that will have to be exceed so the module stops being in error Clear log all devices It allows deleting the events report of all the interconnected modules Factory default This option restores the values by default of the transmodulator System information lt allows you to visualize the basic information of the module model no of series firmware version etc
8. transponder has encoded channels in order to distribute them freely you have to install the PCMCIA subscriber card in the Common Interface slot Saneca 1 FTA Saraca 3 FTA Sersoai FTA Sensos 5 FTA Bemor 2 Bewa Y FTA Sensce 3 FTA Sanos B FTA Sarvica d FTA Seneca 5 Sence 6 FTA Service Serios 2 FTA Sence 8 Service 4 FTA Sanace FTA Sonic amp FTA Serios FTA The tuned channels of the transponder are modulated according to the DVB T rules in two multiplex In cases where the transponder has encoded channels if you wish to distribute them freely you will have to link a PCMCIA subscriber card to each one of the two outputs of the multiplex Out Models with a serial number lower than a 075511441882 DVB T COFDM Contiguration of the channels and output parameters Er ii 1 4 Programming Models with a serial number higher than a 075511441882 DVB T COFDM AT MH Bit Miie Contiguration of the channel and the output parameters of the multiplex The channel of the second multiple will be set by default as the consecutive channel of the one in the first multiplex TSF 310 Cl has two ethernet connectors In order to make the programming of the module you have to connect the corresponding programmer to PRO 201 connector You can make the programming through the PRO 201 programmer and also through the mediaMAX EVO and mediaMAX MINI field strength meter 1 4 1 Programming modes
9. 048 8 709 9 676 10 246 10 556 11 709 12 064 15 612 16 086 17 564 18 096 19516 20 107 20 491 21 112 17 564 18 096 23 419 24 128 26 346 27 144 29 273 30 16 30 787 31 668 Useful channel capacity 7 MHz EEN Guad Interval 5 123 5 278 6 83 7 037 7 684 7 917 8 538 8 797 8 709 9 676 10 246 10 556 13 661 14 075 15 369 15 834 17 076 17 594 15 24 16 934 17 93 18 473 13 063 14 515 15 369 15 834 17 418 19 353 20 491 21 112 9 595 93 053 93 751 21 772 25 614 26 39 22861 26 895 37 71 Useful channel capacity 6 MHz Guad Interval 1 8 1 16 1 32 4 147 4 391 4 524 5 529 5 855 6 032 6 221 6 587 6 786 6 912 7 318 7 54 7 257 7 684 7 917 8 294 8 782 9 048 1 059 11 709 12064 9 441 13 173 13 572 3 824 14 637 15 08 4 515 15 369 15 834 2 441 13 173 13 572 6 588 17 564 18 096 8 662 19 76 20 358 20 735 21 955 29 62 21 772 23 053 23 751 Modulation FEC codification 1 2 3 732 4 976 5 599 6 221 6 532 7 465 9 953 1 197 2 441 3 063 1 197 4 929 6 796 8 662 9 595 QPSK Useful channel capacity 6 MHz Modulation Codificaci n FEC 1 4 3 110 4 147 4 665 5 184 5 443 6 221 8 294 9 331 0 368 0 886 9 331 2 441 3 996 5 551 6 329 Note Only aplicable for DVB H 1 8 1 16 1 32 3 456 3 659 3 770 4 608 4 879 5 027 5 184 5 489 5 655 5 760 6 099 6 283 6 048 6 404 6 598 6 912 7 318 7 540 9 216 9 758 10 053 0 368 10 978 11 310 1 520 12 197 12 567 2 096 12 807 13 19
10. 1 32 FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example ina FEC 2 3 relation we will find 2 information bits and 1 redundant bit Modulation Output modulation format 4 QPSK 16 16 QAM 64 64 QAM Advanced settings Mode Selection of the modulation standard DVB T and DVB H Note The output useful bits rate will depends on the following parameters Bandwidth guard interval FEC codification and modulation In the Attachment you will find all the information related to the resulting useful bit rate in each configuration 5 Set Output channel In this option you can configure the different parameters of the cable signal Channel standard It allows you to select the channelling of the cable signal standards Options BG BG PAL BG IT 11 M NTSC PAL M PAL N PAL DK PAL I BB_AU DK PAL L PAL Channel Output channel of the cable modulation When you select the output channel the field Frequency MHz will be modified automatically adapting itself to the selected channel Options C2 C69 Frequency MHz Output frequency of cable modulation When you modify this field the field Channel will be also modified indicating the channel equivalent to the selected frequency in the case that this frequency corresponds to the frequency of a channel Options 47 862 MHz Level Regulation of the output level of the modulated
11. 5 0 368 10 978 11 310 3 824 14 637 15 080 5 551 16 466 16 965 1 279 18 296 18 850 8 143 19 211 19 793 u R O E w o gt O 5 lt L 19 TSF 310 Cl version_en_2 0 FTE maximal Wie maximal ESPA A Mogoda 110 Pol Industrial Can Salvatella 08210 Barbera del Valles Barcelona Espana Tel 00 34 93 729 27 00 Fax 00 34 93 729 30 73 ftemaximal ftemaximal com www ftemaximal com DACIEI AND Auf der H he 8 44536 L nen Deutschland Tel 00 49 0 23 18 78 5 01 Fax 00 49 0 23 18 78 5 200 info ftemaximal de www ftemaximal de FRANCE 16 ZAE Les Mouilles 74570 Groisy Tel 00 33 450 68 80 17 Fax 00 33 450 68 84 68 sav ftemaximal fr www ftemaximal com PORTUGAL Rua Jos Carlos Ary dos Santos A das Lebres Loures 2670 791 Santo Ant o do Tojal Tel 00 351 219 83 87 00 Fax 00 351 219 83 87 09 ftemaximal ftemaximal pt www ftemaximal com ITALIA Via Edison 29 42040 Calerno di Sant llario d Enza RE Tel 00 39 05 22 90 97 01 Fax 00 39 05 22 90 97 48 fte fte it www ftemaximal com UNITED ARAB EMIRATES P O Box 262442 Jebel Ali Free Zone Warehouse FZS5ABO3 Dubai Tel 00 971 4 886 5700 Fax 00 971 4 886 5701 www ftemaximal ae
12. 75511441882 15 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI 1 5 Accessories and example of installation Example of installation Models with a serial number lower than a 075511441882 Models with a serial number higher than a 07551 1441882 OS 100 OS 100 25085 aus an zm mm 18 mm mm M TF m7 Installation that consist of 6 TSF 310 Cl and that will allow tuning channels up to 6 different transponders and to distribute them through a TV network in DVB T The new models TSF 310 CI with twin output allow distributing up to 12 multiplex in the installation The distributed channels need a terrestrial receiver in order to be decoded The number of modules TSF 310 Cl that can be fed by the power supply SPS 310 will depend on the number of CAM s and their consumptions Ifthe total amount of modules that are connected to the power supply have two CAM s inserted the SPS will be able to feed only 5 modules In any other case the power supply will be able to feed 6 modules In order to guarantee the right running of the different equipments of the installation we recommend you to provide the inputs and outputs which are not used with a 75Q load OUT Accessories Programmer Field strength meter Field strength meter Mod PRO 201 Mod MediaMAX EVO S2 Mod MediaMAX MINI S2T Code 2003123 Code 3001006 Code 3001026 16 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI Wide
13. DVB S QPSK DVB S2 QPSK 8PSk and the subsequent modulation in DVB T COFDM of it A feature of this equipment is its modulator in Vestigial Side Band or VSB This modulation can be used to distribute adjacent channels in one distribution without any intermodulation problem Each module has one Loop connector to cascade several modules at input and a Mix connector to do same in output channels The output channel is selectable between C2 and C69 All parameters are programmed by the means of PRO 201 or the EVO or MINI series of field strength meter and they are monitored in the display of programmer or in the 5 TFT screen of field strength meter TSF 310 Cl has two Common Interface slots TSF 310 Cl 1 Two colored led It indicates the different states of the device 2 Cl Common Interface 3 OUT This connector supplies the modulated channel according to the selected standard in the module and mixes it with all the signals that it receives through the MIX connector 7 4 MIX Input of mixing of the module 5 LNC IN To connect to the LNC or to the LOOP OUT output of the previous module 2 g 6 LOOP OUT To connect to the ANT IN input of the next module 7 RS 232 Ethernet connector to cascade modules with the RCM 310 telecontrol unit with the RJ45 RJ45 cable provided 8 PRO 201 Ethernet connector to make the programming with the programmer R 9 DC connectors It has two connectors for input output 3 4 States of two color
14. RMITY WITH FOLLOWING DIRECTIVES Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC If you wish a copy of the conformity declaration please contact to the company sch Ka TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI ATACHMENT Depending on the configured parameters we are going to obtain one particular channel capacity output useful bit rate In order to make an estimation of this output bits rate we have to take into account the following parameters Symbol duration Ts For signals of 8 MHz 2K 1705 carrier Mode 8K 6817 carrier 4K 3409 carrier Symbol duration 896 448 us 294 us Guard Interval 1 16 1 16 Duration 1 32 Tus For signals of 7 MHz Mode 8K 6817 carrier 4K 3409 carrier 2K 1705 carrier Symbol duration 1024 us 512 us 256 us Guard Interval 32us For signals of 6 MHz 8K 6817 carrier 4K 3409 carrier 9K 1705 carrier Symbol duration 1194 6 us 597 3 us 298 6 us Mbu Duration 298 7us 149 3us 74 7us 37 3us 149 3us 74 6us 37 3us 186us 746us 37 3us 186us 9 3us For signals of 5 MHz 2K 1705 carrier Modo 8K 6817 carrier 4K 3409 carrier Symbol duration 1433 6 us 597 3 us 298 6 us Guard Interval 1 16 1 32 1 16 1 32 1716 1 32 Duration 358 4us 179 2us 89 6us 179 2us 89 6us 11 2us Modulation Modulation QPSK 16 QAM 64 QAM FFT Mode 1512 6817 3409 1705 Bits rat
15. changing the standard position into the high definition position In the first line you have to select the high definition service and in the second line you have to select the same service but in standard definition Change in Service ID From this position you can change the PID Number of the chosen service Change service name HDSimulCast Change in Service ID 10 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 Cl Next it is attached the identification table NID ONID of the main satellites You will be able to find more information in the law ETSI TR 101 162 v1 2 1 Hotbird 13 E Eutelsat 13 E 318 Eutelsat 13 E System Astra 19 2 E 1 1 Astra Satellite Network 19 2 E Astra 93 3 25 3 25 Astra n n 1 23 Astra 28 2 E 2 Astra Satellite Network 28 2 E Nilesat 7 W 2048 Nilesat 101 Hispasat 30 W 33 Hispasat Network 1 9 Common Interface This option allows checking the information and configuring the parameters regarding the conditional access Selecting Slot It selects the Slot where the CAM for decoding the services is inserted Cl Menu From here you can reach the menu of the card inserted in the CAM Decrypted From this option you can add or remove manually the services that are being decoded by the card Deactivating all decrypted From this option you can remove all the services that are decoding the conditional access card
16. channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes Note If in the existing installation there are already services that have LNC system you will have to configure the position of the module services in order to avoid conflicts with other net services Decrypt services From this option you can add or remove manually the services that are being decoded by the card Delete services Add services CAM Reset It allows making a reset in the selected CAM Date Hour Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date SW version info It allows you to visualize the basic information of the module model firmware version etc MUX number It configures the number of output multiplex Options 1 or 2 Global Update It allows carrying out the update of all the modules that are interconnected at the same time Note If the serial number of the device is higher than 075511441882 you have to select in which one of the two modules you want to make the configuration in each case This option is available only in devices with a serial number higher than a 0
17. e calculation total fs b L botal Where Fs Symbols frequency symbols sec fs 1 Ts Ts Symbol duration Symbol Time Guard Interval time b Number of bits per symbol depending on the modulation L Number of data carriers depending of FFT mode Bits rate calculation useful TD yi TD orai Codif ve i Codifkeed Salomon FEC Cod FEC Codification 1 2 2 3 3 4 5 6 7 8 Reed Salomon Cod Codification made by the means of Reed Salom n algorithym 188 204 Case study example For example in the case of a DVB T transmission in Spain the configured parameters would be the following 8k mode 2 3 FEC Ya guard intervals 64QAM constellation for an 8 MHz channel and using the previous formula you will get the following channel useful capacity Tb 19 905Mbps til Note As you select a configuration with a higher output channel capacity the protection grade against mistakes gets proportionally decreased Next it is shown the channel capacity for systems without hierarchy in all the cases of constellation guard interval and codification relation for transmissions of 8MHz 7MHz 6MHz y BMHz DVB H The useful capacity channel is identical for modes 2k Ak DVB H and 8k 18 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI Useful channel capacity 8 MHz ee Guad Interval Modulation FEC codification 1716 1 39 5 855 6 032 7 806 8 043 8 782 9
18. ed leds 1 Initialization mode Green main application charged Blinking Green Completing the initial sequence at the moment when the module gets initialized the led will turn into one of the states the operating mode Red Phase of initializing the module 2 Operative Mode Green The system is working properly Orange At least one critical event has been recorded in the module The led will only change into green when the registration of events has been read by the programmer Red Error or alert detected in the running of the device the led will be on only as long as the error alert is present Once the error or the alert disappears the led will change into orange because the error alert is stored in the registration of events 3 Programming mode When the module detects an external programmer the led will blink in the next sequence green orange red Once you leave the programming mode the led will turn into the corresponding operating mode D TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI Stages of transmodulator TSF 310 Cl Input 950 MHz DVB S QPSK DVB S2 8PSK QPSK 2150 MHz Selection of a tuned satellite transponder y Transmodulation Models with a serial number lower than a 075511441882 Models with a serial number higher than a 075511441882 SERVICES FILTERING The tuned channels of the transponder are modulated according to the DVB T rules If the
19. every time a new input carrier is tuned This state is only recommended to be used for making test in the module Off The automatic mode is deactivated the services have to be manually selected Advanced settings Network It allows making the adjustment of the identification parameters of the multiplex TS ID Transport Stream identification value It is recommended to configure a value different from TS ID for each one of the output multiplex configured Net ID Net identification value Original Net ID Original net identification value Network Name Name associated with the net Tables It allows modifying the value of the following information tables of the DVB NIT SDT and PAT services Services Change service name It allows changing the name of the service manually In order to do so please choose the service in the first line and then write the new name in the second line Then you have to press modify in order to save the changes HDSimulCast In cases where we receive in an installation the same channel in high definition and in standard definition the HD Simualcast function allows to exchange the position of the LNC of both channels If the user has a device compatible to HD Simulcast and the module has been correctly configured when tuning the standard definition channel it will move to its position in high definition automatically This option allows moditying manually the position of the LNC ex
20. he cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Antenna Feeding tone towards the LNC Options OV 13V 13V 22kHz 18V 18V 22KHz 13V AUT 18V AUT DiseqC In this option you can set the DisegC configuration A B C D and None Auto SR Auto Symbol Rate You will be able to select if the detection of the Symbol Rate is going to be Automatic On or Manual Off In Manual mode Off the value of the Symbol Rate should be fixed by the user based on the provider s information In Automatic mode On the meter will automatically identify the SR when a Satellite carrier is tuned This feature is very useful when the provider s information is unknown The SR value found will appear in the field of selection of the SR menu This value found by the meter could not correspond exactly to the real broadcast SR but to a very close value Note The Automatic Symbol Rate feature does not work when the carrier quality is very poor or and with a very low Power Level Mode This option allows selecting the standard DVB of the transponder that you want to tune Options DVB S1 DVB S2 and auto Terrestrial modulation Out Terr These options allow configuring the DVB T DVB H modulator of the device Modulation Output modulation format QPSK 4 QAM 16 QAM 64 QAM Invert Spectrum inversion Activate or deac
21. ing that there was an error storing the data and it will be not stored Internal Always the internal memory is used to store the data Load programs from USB This option allows importing programs from a USB memory to the field strength meter Before using this option you must connect a USB memory Save programs to USB This option allows copying the programs stored in the external USB 2 0 storage device Write Alias It allows saving the alias of the module in the program Options Yes No 8 Set Output Services This option allows making the selection of the services that you wish to include in the output multiplex Add Remove services lt allows adding the services to the multiplex and also removing the ones previously included The lower bar informs about the avallable space in the output multiplex As you add more services the space available will decrease Once you have tuned a transponder in the Input Set Up section and you have selected the DVB T DVB H modulator configuration in the Modulator Set Up section you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services 8 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 Cl Adding services 1 Select Service to add option 2 Select one of the transponder 3 Once you have chosen the services you want to add service select the Add Remove button to include the
22. ion of the output level of the modulated signal Options O 15dB Summary table Satellite input Terrestrial output TV output LO frequency Modulation RF Channel Input Frequency Invert Spectrum Inversion RF Level Symbol Rate Guard Interval Gl Antenna Bandwith BW Diseqc Tx Mode FFT Mode Symbol rate auto FEC DVB Mode Mode 2 Auto This option allows saving and loading the configuration of the module in the PRO 201 programmer Read from module lt stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of the module been correct Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps to make a correct configuration of the headend are specified below 1 Select the option Write to module 2 Select the position of the CFG 3 A window will appear and it will let through Up Down buttons Press OK memory that you wish to copy in the you know that the configuration made to continue module Please verify that the data of has been correct the selected memor
23. lue of the Symbol Rate should be fixed by the user based on the provider s information In Automatic mode On the meter will automatically identify the SR when a Satellite carrier is tuned This feature is very useful when the provider s information is unknown The SR value found will appear in the field of selection of the SR menu This value found by the meter could not correspond exactly to the real broadcast SR but to a very close value Note The Automatic Symbol Rate feature does not work when the carrier quality is very poor or and with a very low Power Level DVB This option allows selecting the standard DVB of the transponder that you want to tune Options DVB S1 DVB S2 and auto LNB Supply In this option you can set the parameters concerning the LNB RF IN Voltage 13V 18V and Off 22 kHz Tone Off On and Auto DisegC Switch A B C D and Off 5 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI 4 Modulator Set Up This option allows configuring the DVB T DVB H modulator of the device Bandwidth Selection of the Bandwidth of the modulated signal 8 MHz 7 MHz 6 MHz and 5MHz The 5 MHz option is only supported by DVB H standard FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard Spectrum inversion Activate or deactivate the spectrum reverse in the modulation Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and
24. ng the connections 14 Never put any heavy object over the device since it could get damaged 15 If the device is going to remain some time without use it is recommendable to disconnect it from the electrical net 16 The repairmen and the maintenance of the device must be done by TV and radio specialised technicians 1 2 Box content Fte THO THO 7 TEO CA 7 TEF TF TSP OS TFF TF CE KN 4 9 x Link F male F male DC Cable TSF 310 Cl Cable 12 cm PIN to PIN RJ45 RJ45 Stopper a TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI The models with a serial number higher than 075511441882 will be provided with a double DVB T output that will allow distributing the channels of the tuned transponder in two consecutive multiplex In order to configure the device we will have two selectable modules The configuration of the input transponder is the same for both modules all the other options of configuration are independent With the following exceptions The output channel of the second module will be set automatically as the consecutive channel after the one configured in the first module The output level of the multiplex will be set by the output level configured in the first module 1 3 Description and connections The module TSF 310 Cl is used for the reception of free channels that obey the DVB S DVB S2 standards Each module allows the reception of a complete transponder in
25. nual Inside the manual menu there are specified the different options for setting up the input output and modulation parameters Nota If you have a module with a serial number higher than 075511441882 it will allow you to choose between two units with an only device connected to the programmer Unit 1 Mux O or Unit 2 Mux 1 1 This field shows the type of parameter that is selected at the moment Options Input Sat Out Terr Out TV 2 This field shows the parameter that is selected In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press OK N Satellite input Input Sat In these options you will be able to configure the input parameters of the satellite signal L O freq Local oscillator Selection of the local oscillator that you wish to use Fl KU C K9750 K10000 K10600 K10700 K10750 K11250 K11300 K11325 Freq Input Frequency MHz Transponder frequency that you wish to tune In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Symbol Rate Symbol speed required by the transponder In order to introduce the symbol rate press the OK button and t
26. s making values by default to all the interconnected modules Activate the following output It allows activating or deactivating the output of the second Unit Note This option is available only in devices with a serial number higher than a 075511441882 ay TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI 7 Program management New program This option allows creating a program with the current configuration of a module or group of modules Load program It allows loading a previously created program on a module or group of modules Delete program It allows deleting a program Device to process Current The creation or loading of a program will be applied only in the module that is currently connected All The creation or loading of a program will be applied to the whole group of connected modules Working disk With this option we have the possibility of choosing if we want to work into the internal disk or in the external storage device USB 2 0 Once the option is selected a dialog box will appear and we will be able to choose among three different options Auto The Meter decides where the data will be stored If there is external memory connected the Meter will store the data in it If not it will use the internal memory USB The Meter always will try to use the external memory connected to the USB port If this memory has not been connected an error message will be shown remind
27. service in the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services Excessive capacity It is recommended to remove services Recomendad capacity lower to 85 Removing services 1 Select the Service to remove 2 Select one of the transponder 3 Once you have chosen the service option services you want to remove select the Add Remove button to remove the service in the multiplex Remove all services It allows removing all the services included in the multiplex Modify LCN The LNC function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LNC support to make the ordination of channels automatically in the existing installation there are already services that have LNC you will have to configure the position of the module services in order conflicts with other net services 9 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 Cl Bandwidth limitation It allows selecting the of the capacity of the output channel Auto service addition On It selects the services automatically when an input carrier is tuned and when the list of selected services is empty The receiver will have this state by default Always It selects the services automatically
28. tivate the spectrum reverse in the modulation Gl Guard interval Allows selecting the guard interval of the modulation 1 4 1 8 1 16 and 1 32 BW Bandwidth Selection of the Bandwidth of the modulated signal 8 MHz 7 MHz and 6 MHz and 5MHz The 5 MHz option is only supported by DVB H standard Tx Mode FFT Mode 8K 4K and 2k The 4k option is only supported by DVB H standard FEC Indicates the relationship between the redundant bits and the transmitted information bits 1 2 2 3 3 4 5 6 y 7 8 For example in a FEC 2 3 relation we will find 2 information bits and 1 redundant bit Mode Selection of the modulation standard DVB T and DVB H 12 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 Cl Note The output useful bits rate will depend on the following parameters Bandwidth guard interval FEC codification and modulation In the Attachment you will find all the information related to the resulting useful bit rate in each configuration Output configuration TV output In these options you can configure the output parameters of the terrestrial signal RF Channel MHz Output frequency of terrestrial modulation In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 47 862 MHz RF Level Regulat
29. vice connected to the programmer Unit 1 or Unit 2 2 Device Status In the option Device Status are specified the main parameters of the module at this moment Front End It indicates whether the module is hooked or without signal Input bit rate Transfers of data in the satellite tuner input Output bit rate Transfer of data in the module output BER before and after Viterbi It indicates the error rate of bits of the input signal before and after the correction produced by Viterbi algorithm MER Parameter that indicates the quality of the input modulated digital signal expressed in dB Noise Margin It indicates the difference between the value of current C N and the value of C N at the point of pixilation of the signal that is the quantity of dBs of C N measure that are needed to lose the input signal Temperature It indicates the current temperature of the module in C 3 Set Front End In this option you will be able to configure the input parameters of the satellite signal Local oscillator Selection of the local oscillator that you wish to use Fl KU C K9750 K10000 K10600 K10700 K10750 K11250 K1 1300 K11325 Frequency MHz Transponder frequency that you wish to tune Symbol speed Symbol speed required by the transponder Auto symbol rate You will be able to select if the detection of the Symbol Rate is going to be Automatic On or Manual Off In Manual mode Off the va
30. y correspond to the channel that you wish to copy 13 TSF 310 Cl version_en_2 0 FTE maximal User s manual TSF 310 CI 3 Config In Config option the information concerning the transmodulator is given Teer SV CL LCN gt Read file Delete file Read log It allows reading the registered events in the module Ter 310 CI LCN gt Read LOG file Delete LOG file 1 Select the option Read LOG file through Up Down buttons Press OK to continue TSE set OF to Show LOG 2 Press OK again to show the log file TSE e ET EIERE Status Us Dan Wi We Front end lock 3 A new window will appear It will show the information about the registered events in the module Press the following keys in order to scroll up and down the screen up down Delete LOG file It allows deleting all events stored until this moment Factory default This option restores the values by default of the transmodulator Update FW It allows carrying out the firmware update from the programmer Output services This option allows making the selection of the services that you wish to include in the output multiplex Once you have tuned a transponder and you have selected the DVB T DVB H modulator configuration you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services Add Services Tor 210 Or BW usage Delete services Add services 000
Download Pdf Manuals
Related Search