Fte maximal TSQ 310 CI
Contents
1. Spectrum inversion Activate or deactivate the spectrum inversion in the modulation Modulation Modulation Format Options 16 QAM 32 QAM 64 QAM 128 QAM 256 QAM Roll off factor Roll off factor reduces the interference between symbols thanks to the raised cosine filtering the bigger this value is the less interference between symbols that will be caused Typical Value according to rules DVB C 15 Options 15 13 5 Output configuration In this option you can configure the different parameters of the cable signal Channel standard lt allows you to select the channelling of the cable signal standards Options BG BG PAL BG IT 11 M NTSC PAL M PAL N PAL DK PAL BB_AU DK PAL L PAL Channel Output channel of the cable modulation When you select the output channel the field Frequency MHz will be modified automatically adapting itself to the selected channel Options C2 C69 Frequency MHz Output frequency of cable modulation When you modify this field the field Channel will be also modified indicating the channel equivalent to the selected frequency in the case that this frequency corresponds to the frequency of a channel Options 47 862 MHz Level Regulation of the output level of the modulated signal Options O 15dB Calibration Allows the realization of two tests in order to verify the correct running of the device Output deactivate It allows activating or deactivating2. Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date Set date time all devices Loading the current date and time of the module in the rest of interconnected modules Alias Write alias It allows you to assign a name alias to the module you are programming Option only available when the Alias Auto option is configures as none manual mode Auto Alias It allows configuring the name alias of the modules automatically Options Channel Frequency Service None Upgrade Send Firmware from USB It allows carrying out the firmware update from the USB device Send firmware to all It allows carrying out the update of all the modules that are interconnected at the same time 7 TSQ 310CI version_en_1 0 FTE maximal User s manual TSQ 310 Cl Configure all devices Input values to all devices It allows copying the current input configuration in all the interconnected modules Modulator values to all devices It allows copying the configuration of the current modulator in all the interconnected modules Output values to all devices It allows copying the current output configuration in all the interconnected modules Factory default to all devices It allows making values by default to all the interconnected modules T Program management New program This option allows creatin
3. Via Edison 29 42040 Calerno di Sant llario d Enza RE Tel 00 39 05 22 90 97 01 Fax 00 39 05 22 90 97 48 fte fte it www ftemaximal com UNITED ARAB EMIRATES P O Box 262442 Jebel Ali Free Zone Warehouse FZS5AB03 Dubai Tel 00 971 4 886 5700 Fax 00 971 4 886 5701 www ftemaximal ae
4. 2 0 storage device Write Alias It allows saving the alias of the module in the program Options Yes No 8 Set Output Services This option allows making the selection of the services that you wish to include in the output multiplex Add Remove services It allows adding the services to the multiplex and also removing the ones previously included The lower bar informs about the available space in the output multiplex As you add more services the space available will decrease Once you have tuned a transponder in the Input Set Up section and you have selected the DVB C modulator configuration in the Modulator Set Up section you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services eS TSQ 310 Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl Adding services 1 Select Service to add option 2 Select one of the transponder 3 Once you have chosen the services you want to add service select the Add Remove button to include the service in the multiplex Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services Recomendad capacit Excessive capacity ie It is recommended to remove lower to 85 services Removing services 1 Select the Service to remove 2 Select one of the transponder 3 Once you
5. Fle TSQ 310 Cl USER S MANUAL User s manual TSQ 310 Cl NOTE This user s guide is adapted to software version OOOD of TSQ 310 Cl dated 12 04 2011 For future software updates you can download the users guide from the following website http www ftemaximal com Chapter 1 Installation 1 1 Safety Measures 1 Never place the device next to hot sources 2 Never undergo the device to temperatures that exceed its level of operation 3 Never expose the device to leakings nor spatterings 4 Never place objects that contain liquids over the device 5 Respect the ventilation slots of the device do not cover them with any kind of object 6 The space around the device must be free of objects in a minimum radius of 40cm 7 Avoid locations with possibilities of spilling liquids on the inside of the device and with important changes of temperature 8 Never open the device by yourself due to electric risk In case of problems go always to qualified technicians 9 Never under no circumstances open the device when connected to the electrical net 10 During the handling it is better to disconnect the device from the electrical net 11 Obey the electricity security rules during the assembling Use materials that obey the current law 12 The connecting plug must be accessible in a fast and simple way to have a fast disconnection 13 Never touch the plug with wet hands Also disconnect always the device before handling
6. With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Options 47 862 MHz RF Level Regulation of the output level of the modulated signal Options O 15dB Summary table Satellite input L O frequency Input Frequency TV output Cable output Invert Spectrum Inversion Modulation RF Channel RF Level Symbol Rate Roll off factor Antenna Symbol speed Diseqc Symbol rate auto DVB Mode 13 TSQ 310Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl 2 Auto This option allows saving and loading the configuration of the module in the PRO Tes VoOCL 201 programmer gt head from Modules Write to Module Read from module It stores the current configuration of the module in the memory of the programmer The steps to make a correct reading of the headend are specified below ToS OCT SOS MOCT we MEO STO gt Read from Module Operation finish Write to Module Free position 1 Select the option Read from 2 Select the position of CFG 3 A window will appear and it will let module through Up Down buttons memory where you wish to save the you know that the reading made has Press OK to continue current configuration of the module been correct Write to module It loads in the module one of the configurations previously saved in the memory of the programmer The steps
7. of the chosen service Next it is attached the identification table NID ONID of the main satellites You will be able to find more information in the law ETSI TR 101 162 v1 2 1 Satellite Net ID Original Net ID Description Hotbird 13 E Eutelsat 13 E Eutelsat 13 E System Astra 19 2 E 1 1 Astra Satellite Network 19 2 E Astra 23 E 3 25 3 25 Astra n n 1 23 2 2 Astra 28 2 E Astra Satellite Network 28 2 E Nilesat 7 W 2048 2048 Nilesat 101 Hispasat 30 W Hispasat Network 1 9 Common Interface This option allows checking the information and configuring the parameters regarding the conditional access Selecting Slot lt selects the Slot where the CAM for decoding the services is inserted Cl Menu From here you can reach the menu of the card inserted in the CAM Decrypted From this option you can add or remove manually the services that are being decoded by the card 11 TSQ 310Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl Deactivating all decrypted From this option you can remove all the services that are decoding the conditional access card PRO 201 Note From PRO 201 programmer you can only carry out the programming of a single module in order to carry out the programming of several modules at the same time you have to use a mediaMAX EVO or mediaMAX MINI series field strength meter When you connect the PRO 201 programmer it will proceed to recognize the modu
8. of the services of the multiplex This function will allow the users who have a receiver with LNC support to make the ordination of channels automatically Select a channel through Left Right buttons and introduce the position Press the OK button and the cursor will be placed over the number With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the changes the position of the module services in order to avoid conflicts with other net services f Note If in the existing installation there are already services that have LNC system you will have to configure Decrypt services From this option you can add or remove manually the services that are being decoded by the card Delete services Add services Date Hour Setting of the date and time of transmodulator It is appropriate to maintain these parameters set in order to have the registration of errors linked to the current time and date SW version info It allows you to visualize the basic information of the module model firmware version etc Global Update It allows carrying out the update of all the modules that are interconnected at the same time 15 TSQ 310 Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl 1 5 Accessories and example of installation Example of installation Installation that consist of 6 TSQ 310 Cl and that will allow tuning channels up to 6 different transp
9. the connections 14 Never put any heavy object over the device since it could get damaged 15 If the device is going to remain some time without use it is recommendable to disconnect it from the electrical net 16 The repairmen and the maintenance of the device must be done by TV and radio specialised technicians 1 2 Box content Fte THO TSO TEO OS TEF TAF TE Oi 7 TEP 7 TPF CI Woa 2 x Bridge F male F male DC Cable TSQ 310 Cl Cable 12 cm PIN to PIN RJ45 RJ45 Stopper 1 TSQ 310CI version_en_1 0 FTE maximal User s manual TSQ 310 Cl 1 3 Description and connections The module TSQ 310 Cl is used for the reception of free channels that obey the DVB S DVB S2 standards Each module allows the reception of a complete transponder in DVB S QPSK DVB S2 QPSK 8PSk and the subsequent modulation in DVB C QAM of it A feature of this equipment is its modulator in Vestigial Side Band or VSB This modulation can be used to distribute adjacent channels in one distribution without any intermodulation problem Each module has one Loop connector to cascade several modules at input and a Mix connector to do same in output channels The output channel is selectable between C2 and C69 All parameters are programmed by the means of PRO 201 or the EVO or MINI series of field strength meter and they are monitored in the display of programmer or in the 5 TFT screen of field strength meter TSQ 310 Cl has t
10. the output of transmodulator Pure carries output It allows activating or deactivating the DVB C modulation allowing visualizing the carrier without modulation in the selected frequency 6 TSQ 310Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl 6 System This option provides information of the transmodulator System logfile In this field are indicated the registered events in the module Read log It allows reading the registered events in the module Clear log It allows deleting all events stored until this moment Export log to USB It allows you to export all events registered to the connected USB device NM low Limit dB An event of error will be recorded when the value of Noise Margin is lower than the set value NM hight limit dB Once the event of error is recorded Noise Margin lt Limit Lower NM this will be Noise Margin value that will have to be exceed so the module stops being in error Clear log all devices It allows deleting the events report of all the interconnected modules Factory default This option restores the values by default of the transmodulator System information It allows you to visualize the basic information of the module model no of series firmware version etc Settings This option allows saving and loading the configuration of the module carrying out firmware update or making an adjustment of the time and date of the module Clock Set Date and time
11. 1 45 MS s DVB S2 1 37 MS s 16 QAM 32 QAM 64 QAM 128 QAM 256 QAM 1 6 96 MS s 13 15 C2 C69 Output connectores Female F connector Output Level 80 dBuV Regulation margin MIX Losses Band spurious RJ 45 PRO 201 media Max EVO and media Max MINI Operating temperature O0 C 45 C 800 Consumption 12V mA 300 i 75x265x150 mm Weight 1 4Kg Chapter 3 Declaration of conformity CONFORMITY DECLARATION WE FTE MAXIMAL DECLARE THAT THE PRODUCT TSQ 310 Cl IS IN CONFORMITY WITH FOLLOWING DIRECTIVES Low Voltage Directive 2006 95 EC EMC Directive 2004 108 EC If you wish a copy of the conformity declaration please contact to the company 17 TSQ 310Cl version_en_1 0 FTE maximal Fle maximal ESPANA Mogoda 110 Pol Industrial Can Salvatella 08210 Barbera del Vall s Barcelona Espa a Tel 00 34 93 729 27 00 Fax 00 34 93 729 30 73 ftemaximalOftemaximal com www ftemaximal com DEUTSCHLAND Auf der H he 8 44536 L nen Deutschland Tel 00 49 0 23 18 78 5 01 Fax 00 49 0 23 18 78 5 200 infoOftemaximal de www ftemaximal de mi RVANN Od mt 16 ZAE Les Mouilles 74570 Groisy Tel 00 33 450 68 80 17 Fax 00 33 450 68 84 68 sav ftemaximal fr www ftemaximal com PORTUGAL Rua Jos Carlos Ary dos Santos A das Lebres Loures 2670 791 Santo Ant o do Tojal Tel 00 351 219 83 87 00 Fax 00 351 219 83 87 09 ftemaximal ftemaximal pt www ftemaximal com ITALIA
12. ars the led will change into orange because the error alert is stored in the registration of events 3 Programming mode When the module detects an external programmer the led will blink in the next sequence green orange red Once you leave the programming mode the led will turn into the corresponding operating mode 2 TSQ 310 Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl Stages of transmodulator TSQ 310 Cl Input DVB S QPSK DVB S2 8PSK QPSK 850 MHz 2150 MHz Selection of a tuned satellite transponder y Transmodulation SERVICES FILTERING Service 5 Service 7 FTA Service 8 Service 9 FTA The tuned channels of the transponder are modulated according to the DVB C rules If the transponder has encoded channels in order to distribute them freely you have to install the PCMCIA subscriber card in the Common Interface y Out DVB C QAM 47 MHz BGZ MHz Contiguration of the channels and output parameters 1 4 Programming TSQ 310 has two ethernet connectors In order to make the programming of the module you have to connect the corresponding programmer to PRO 201 connector You can make the programming through the PRO 201 programmer and also through the mediaMAX EVO and mediaMAX MINI field strength meter 1 4 1 Programming modes With mediaMAX EVO mediaMAX MINI field strength Through PRO 201 the programming is made module by m
13. by the transponder In order to introduce the symbol rate press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Antenna Feeding tone towards the LNC Options OV 13V 13V 22kHz 18V 18V 22KHz 13V AUT 18V AUT DiseqC In this option you can set the DisegC configuration A B C D and None 12 TSQ 310 CIl version_en_1 0 FTE maximal User s manual TSQ 310 Cl Auto SR Auto Symbol Rate You will be able to select if the detection of the Symbol Rate is going to be Automatic On or Manual Off In Manual mode Off the value of the Symbol Rate should be fixed by the user based on the provider s information In Automatic mode On the meter will automatically identify the SR when a Satellite carrier is tuned This feature is very useful when the provider s information is unknown The SR value found will appear in the field of selection of the SR menu This value found by the meter could not correspond exactly to the real broadcast SR but to a very close value Note The Automatic Symbol Rate feature does not work when the carrier quality is very poor or and with a very low Power Level Mode This option allows selecting the standard DVB of the transponder that you want to tune Options DVB S1 DVB S2 and auto Cable modulator Out Cable This option allows you to config
14. eter you can carry out the programming of all the module modules consecutively as long as they are interconnected with each other through the RJ 45 cable supplied with each unit 3 TSQ 310 Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl 1 4 2 Programming Below you will find the steps to follow in order to make the programming both from corresponding EVO and MINI field strength meter as well as from PRO 201 mediaMAX EVO mediaMAX MINI In order to start programming the TSQ 310 transmodulator you will have to go to Tools option through the key 8 of your field strength meter and to select the Prog Transmodulators option Then it will proceed to recognize the module and to show the main menu In the Prog Transmodulators are shown the different configuration options that this tool offers 1 Module selection The field strength meter allows carrying out the programming of one or several transmodulators from an only transmodulator Without interconnection of modules Interconnection of several modules you can select which An only module connected modules you wish to program 4 TSQ 310CI version_en_1 0 FTE maximal User s manual TSQ 310 Cl 2 State of the module In the option State of the module are specified the main parameters of the module at this moment Transmodulator input It indicates whether the module is hooked or without signal Input bit rate Transfers of da
15. g a program with the current configuration of a module or group of modules Load program It allows loading a previously created program on a module or group of modules Delete program It allows deleting a program Device to process Current The creation or loading of a program will be applied only in the module that is currently connected All The creation or loading of a program will be applied to the whole group of connected modules Working disk With this option we have the possibility of choosing if we want to work into the internal disk or in the external storage device USB 2 0 Once the option is selected a dialog box will appear and we will be able to choose among three different options Auto The Meter decides where the data will be stored If there is external memory connected the Meter will store the data in it If not it will use the internal memory USB The Meter always will try to use the external memory connected to the USB port If this memory has not been connected an error message will be shown reminding that there was an error storing the data and it will be not stored Internal Always the internal memory is used to store the data Load programs from USB This option allows importing programs from a USB memory to the field strength meter Before using this option you must connect a USB memory Save programs to USB This option allows copying the programs stored in the external USB
16. have chosen the option services you want to remove service select the Add Remove button to remove the service in the multiplex 9 TSQ 310 CI version_en_1 0 FTE maximal User s manual TSQ 310 Cl Remove all services It allows removing all the services included in the multiplex Modify LCN The LNC function allows assigning automatically a predetermined position to each one of the services of the multiplex This function will allow the users who have a receiver with LNC support to make the ordination of channels automatically f Note If in the existing installation there are already services that have LNC system you will have to configure the position of the module services in order to avoid conflicts with other net services Bandwith limitation It allows selecting the of the capacity of the output channel Auto service addition On It selects the services automatically when an input carrier is tuned and when the list of selected services is empty The receiver will have this state by default Always It selects the services automatically every time a new input carrier is tuned This state is only recommended to be used for making test in the module Off The automatic mode is deactivated the services have to be manually selected Advanced settings Network It allows making the adjustment of the identification parameters of the multiplex TS ID Transport Stream identification value It is
17. he programmer Output services This option allows making the selection of the services that you wish to include in the output multiplex Once you have tuned a transponder and you have selected the DVB T DVB H modulator configuration you can make the assignment of the services that are going to be included in the output multiplex Adding Removing services 14 TSQ 310Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl Add Services 1 Select the option Add services 2 Select one of the transponder through Up Down buttons Press OK services you want to add through to continue Left Right keys and select the Add button to include the service in the multiplex Delete Services 1 Select the option Delete services 2 Select the service you want to through Up Down buttons Press OK delete with the Left Right keys Then to continue press OK over Rem in order to remove it or press OK over All in order to delete all the services of the multiplex 3 A window will appear and it will let you know that the operation made has been correct 3 A window will appear and it will let you know that the operation made has been correct Note It is not recommended to exceed the 85 of the maximum capacity of the multiplex due to the possible variability of the bits rate of the inputs services LCN The LNC function allows assigning automatically a predetermined position to each one
18. le and to show the main menu In the main menu are shown the different options for configuring the transmodulator We have to use the Up and Down buttons of the keyboard in order to move to the different options and to get into the submenus we have to press OK button 1 Manual Inside the manual menu there are specified the different options for setting up the input output and modulation parameters 1 This field shows the type of parameter that is selected at the moment Options Input Sat Out Cab Out TV 2 This field shows the parameter that is selected In order to move around the different options we have to use the Up and Down buttons of the keyboard Click on OK to edit the selected parameter and Right Left for changing it Once it is configured press OK Satellite input Input Sat In these options you will be able to configure the input parameters of the satellite signal LO freq Local oscillator Selection of the local oscillator that you wish to use Fl KU C K9750 K10000 K10600 K10700 K10750 K11250 K11300 K11325 Freq Input Frequency MHz Transponder frequency that you wish to tune In order to introduce the frequency press the OK button and the cursor will be placed over the frequency With the keys of the cursor we can move through all the digits and change the values Press OK in order to save the value Symbol Rate Symbol speed required
19. onders and to 5 LNC 544 po distribute them through a network of modulated cable in ee jo i DVB C The distributed channels need a cable receiver in es iiia order to be decoded In order to distribute the encoded channels freely you have to install the PCMCIA subscriber card in the Common Interface slot OS 100 B AMP 310 P De T50 310 Cl AT 335 C PVR C130 Cl HDMI E PVR C130 CI HDMI AT 420 PVR C130 Cl HDMI o y i a PVR C130 CI HOMI i PVR C130 Cl HDMI DISTRIBUTION NETWORK PVR C130 CI HDMI installation we recommend you to provide the inputs and outputs which are not used with a 750 load In order to guarantee the right running of the different equipments of the Accessories OUT Programmer Field strength meter Field strength meter Mod PRO 201 Mod mediaMAX EVO S2 Mod mediaMAX MINI S2T Code 2003123 Code 3001006 Code 3001026 B Parabolic antenna OS series Wide band amplifier 47 862MHz Mixer Mod OS 100 AL Mod AMP 310 P Mod MUX 310 Code 0701100 Code 2003520 Code 2003518 16 TSQ 310Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl Chapter 2 Technical features Ref TSQ 310 Cl 2003534 Input frequancy margin 950 2150 MHz Input level 25 a 65 dBm Imput impedance 750 13V 18V 0 29kHz Input connector Female F connector 1 2 2 3 3 4 5 6 7 8 8 9 9 10 1 4 1 3 1 5 2 5 3 5 4 5 DVB RS 204 188 8PSK QPSK Input Symbol Rate DVB S
20. recommended to configure a value different from TS ID for each one of the output multiplex configured Net ID Net identification value Original Net ID Original net identification value Network Name Name associated with the net Tables It allows modifying the value of the following information tables of the DVB NIT SDT and PAT services Services Change service name It allows changing the name of the service manually In order to do so please choose the service in the first line and then write the new name in the second line Then you have to press modify in order to save the changes 10 TSQ 310Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl HDSimulCast In cases where we receive in an installation the same channel in high definition and in standard definition the HD Simualcast function allows to exchange the position of the LNC of both channels If the user has a device compatible to HD Simulcast and the module has been correctly configured when tuning the standard definition channel it will move to its position in high definition automatically This option allows modifying manually the position of the LNC exchanging the standard position into the high definition position In the first line you have to select the high definition service and in the second line you have to select the same service but in standard definition Change in Service ID From this position you can change the PID Number
21. ta in the satellite tuner input Output bit rate Transfer of data in the module output BER before and after Viterbi It indicates the error rate of bits of the input signal before and after the correction produced by Viterbi algorithm MER Parameter that indicates the quality of the input modulated digital signal expressed in dB Noise Margin It indicates the difference between the value of current C N and the value of C N at the point of pixilation of the signal that is the quantity of dBs of C N measure that are needed to lose the input signal Temperature It indicates the current temperature of the module in C 3 Input configuration In this option you will be able to configure the input parameters of the satellite signal Local oscillator Selection of the local oscillator that you wish to use Fl KU C K9750 K10000 K10600 K10700 K10750 K11250 K1 1300 K11325 Frequency MHz Transponder frequency that you wish to tune Symbol speed Symbol speed required by the transponder Auto symbol rate You will be able to select if the detection of the Symbol Rate is going to be Automatic On or Manual Off In Manual mode Off the value of the Symbol Rate should be fixed by the user based on the provider s information In Automatic mode On the meter will automatically identify the SR when a Satellite carrier is tuned This feature is very useful when the provider s information is unknown The SR val
22. to make a correct configuration of the headend are specified below TSO Let ES ee LEI ipso eat eal CFGs01 gt Wrire to Module e o sve oraa 7200 Operation finish Read from Module Output Freq 850000 1 Select the option Write to module 2 Select the position of the CFG 3 A window will appear and it will let through Up Down buttons Press OK memory that you wish to copy in the you know that the configuration made to continue module Please verify that the data of has been correct the selected memory correspond to the channel that you wish to copy 3 Config To LCi In Config option the information concerning the transmodulator is given LON gt Read LOG file Read log It allows reading the registered events in the module telete Toe E De Tao nV wal EO OCT LCN TSEQO3L0C 4 N 00001 Statue US OT Oe T CEE oa Obes Front end lock gt Read LOG file OF to Show LOG Velen TOC File 1 Select the option Read LOG file 2 Press OK again to show the log file 3 A new window will appear It will through Up Down buttons Press OK show the information about the to continue registered events in the module Press the following keys in order to scroll up and down the screen up down Delete LOG file It allows deleting all events stored until this moment Factory default This option restores the values by default of the transmodulator Update FW It allows carrying out the firmware update from t
23. ue found will appear in the field of selection of the SR menu This value found by the meter could not correspond exactly to the real broadcast SR but to a very close value Note The Automatic Symbol Rate feature does not work when the carrier quality is very poor or and with a very low Power Level DVB This option allows selecting the standard DVB of the transponder that you want to tune Options DVB S1 DVB S2 and auto LNB Feeding In this option you can set the parameters concerning the LNB Voltage RF IN 13V 18V and Off Tone 22 kHz Off and Auto In the Switch DiseqC A B C D and Off 5 TSQ 310Cl version_en_1 0 FTE maximal User s manual TSQ 310 Cl 4 Modulator configuration This option allows you to configure the DVB C modulator that the device has Symbol speed The available symbol speed ranges from 1 to 6 96 MS s In order to estimate the output symbol speed you have to take into account the following parameters input modulation input symbol speed input FEC output modulation For example for a 8PSK signal with 22000 MS s and a FEC 2 3 the output symbol speed should be calculated according to the chosen QAM modulation Voymgor in FECA bit symbol 8PSK 2000743 SYMBOL OUT n bit symbol oam n bit symbol oam Modulation QPSK 8PSK 16 QAM 32 QAM 64 QAM 128 QAM 256 QAM 2 symbol Modulation 16 QAM 32 QAM 64 QAM 128 QAM 256 QAM Symbol speed MS s 11000 8800 1333 6286 5500
24. ure the DVB C modulator that the device has Spectrum inversion Activate or deactivate the spectrum inversion in the modulation Modulation Modulation Format Options 16 QAM 32 QAM 64 QAM 128 QAM 256 OAM Roll off factor Roll off factor reduces the interference between symbols thanks to the raised cosine filtering the bigger this value is the less interference between symbols that will be caused Typical Value according to rules DVB C 15 Options 1 5 1 3 Symbol speed The available symbol speed ranges from 1000 to 7000 S s In order to estimate the output symbol speed you have to take into account the following parameters input modulation input symbol speed input FEC output modulation For example for a 8PSK signal with 22000 MS s and a FEC 2 3 the output symbol speed should be calculated according to the chosen QAM modulation FECA n pasted 22000 A 3 IP SYMBOLIN V pti re SYMBOL OUT n bit symbol OAM n bit symbol OAM Modulation QPSK 8PSK 16 QAM 32 QAM 64 QAM 128 QAM 256 QAM Number of bits per symbol Modulation 16 QAM 32 QAM 64 QAM 128 QAM 256 QAM Symbol speed MS s 11000 8800 T333 6286 5500 Output configuration TV output In these options you can configure the output parameters of the terrestrial signal RF Channel MHz Output frequency of terrestrial modulation In order to introduce the frequency press the OK button and the cursor will be placed over the frequency
25. wo Common Interface slots TSQ 310 Cl 1 Two colored led It indicates the different states of the device 2 Cl 2x Common Interface 3 OUT This connector supplies the modulated channel according to the selected standard in the module and mixes it with all the signals that it 5 receives throught the MIX connector 4 MIX Input of mixing of the module 6 5 LNC IN To connect to the LNC or to the LOOP OUT output of the previous module 7 6 LOOP OUT To connect to the ANT IN input of the next module 7 RS 232 Ethernet connector to cascade modules with the RCM 310 g telecontrol unit with the RJ45 RJ45 cable provided 8 PRO 201 Ethernet connector to make the programming with the programmer 9 DC connectors It has two connectors for input output 9 Fte 3 4 States of two colored leds 1 Initialization mode Green main application charged Blinking Green Completing the initial sequence at the moment when the module gets initialized the led will turn into one of the states the operating mode Red Phase of initializing the module 2 Operative Mode Green The system is working properly Orange At least one critical event has been recorded in the module The led will only change into green when the registration of events has been read by the programmer Red Error or alert detected in the running of the device the led will be on only as long as the error alert is present Once the error or the alert disappe
Download Pdf Manuals
Related Search