Chief XCM7000 flat panel ceiling mount
Contents
1. Figure 9 2 Align the center of the interface bracket KK with center of screen See Figure 10 NOTE The diamond shape hole in the bracket corresponds to the center of the mount Center of bracket KK Figure 10 WARNING IMPROPER INSTALLATION CAN LEAD TO DISPLAY FALLING CAUSING SERIOUS PERSONAL INJURY OR DAMAGE TO EQUIPMENT Using screws of improper size may damage your display Properly sized screws will easily and completely thread into display mounting holes If spacers are required be sure to use longer screws of the same diameter 3 Select correct screws spacers if necessary and universal washers from the hardware bag A N and attach brackets KK to back of screen See Figure 10 Attaching Displays to Mounting Rail WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located within the mounting system of the XCM7000 does not exceed a maximum weight capacity of 300 Ibs 136 1 kg CAUTION BEFORE adding display to the mounting rail ensure end caps are in place at BOTH ends of mounting rail IMPORTANT The interface bracket tilt may be adjusted either before or after adding display to mounting rail See Adjustments section 1 Ensure that the latch mechanisms on interface brackets KK are already lowere2. EE into lower slots on array head FF while bringing mounting rail against array head 5 Tighten array head to mounting rail by tightening lock nuts on upper T slot studs and adding two 5 16 lock nuts AA to lower T slot studs See Figure 6 Figure 4 3 Install two 5 16 x 2 self tapping screws DD through two 5 16 split washers CC two 5 16 flat washers Z sides of array head FF into installed column See Figure 4 4 Repeat Steps 1 through 3 for remaining array head FF assuring that second array head is approximately level with first installed array head Adding Mounting Rail 1 Slide four T slot studs EE two in top mounting rail slot and two in bottom into end of mounting rail JJ See Figure 5 Figure 6 Repeat for remaining array head FF Add one end cap X to each end of mounting rail and fasten in place using two 1 4 20 x 1 2 Phillips self tapping screws Y for each end cap See Figure 7 EE x4 JJ Figure 5 Figure 7 XCM7000 Installation Instructions 8 Tighten two 5 16 x 3 4 set screws BB against column See Figure 8 Figure 8 Attaching Interface Brackets to Displays 1 Lowerthe latch mechanism on each interface bracket KK See Figure 9 Latch mechanism
3. using buttonhead screws removed in Step 2 through sides of array head and into side tabs of bracket HH See Figure 2 8 Slide plate raised in Step 5 back into position by turning adjustment bolt on top of array head See Figure 2 9 Repeat Steps 1 through 8 for remaining array head FF o Ex Adjustment bolt Front of array head Figure 2 10 Slide array head FF up from below onto installed column not included See Figure 3 11 Thread bottom coupling Q onto installed column until tight with a minimum of four threads engaged See Figure 3 12 Install and tighten one 10 24 x 1 4 set screw R into bottom coupling Q See Figure 3 Figure 3 Installation Instructions XCM7000 13 Repeat Steps 10 through 12 for remaining array head FF assuring that second array head is approximately level with first installed array head Attaching Mount to CPA Extension Column CAUTION WATCH FOR PINCH POINTS Do not place fingers between moveable parts 1 Slide array head FF up from below onto installed column not included See Figure 4 2 Line up holes in sides of array head FF with holes in column 2 Partially fasten one 5 16 lock nut AA to each stud on upper T slot studs 3 Slide top T slot studs EE with attached lock nuts AA down into top openings on array heads FF See Figure 6 4 Slide studs on lower T slot studs
4. ERED ON MOUNT SPACING X NOT TO BE LESS THAN 18 450 mm 591 150 0 1 00 CH 254 9 Ahi 8 z 22 206 52 4 COLUMNS SOLD SEPARATELY P 45 0 2 TOTAL HEIGHT ADJUST 2 10 1 DOWN 5 71 53 4 145 0 3 8 3 116 i 8 4 1 elite 2119 3 15 75 16 75 E SS 400 0 4255 El MAX VERTICAL i MOUNTING PATIERN Es og 1 0 34 8 6 31 98 812 2 MAX HORIZONTAL MOUNTING PATTERN 34 84 885 0 TLTLOC KOUTS AT 7 6 5 0 5 10 15 20 7 6 BACK TILT 20 MAX FORWARD 4 55 TILT 15 7 v e I e E 7 69 i Fy 195 3 i 74 189 4 HOLE FOR PADLOCK DIMENSIONS INCHES MILLIMETERS DETAIL A SCALE 1 2 5 HOLE DETAILC DETAILB SCALE1 2 SCALE1 2 7 6 HOLE 191 484 DETAILD O HOLE SCALE1 2 15 HOLE 20 HOLE DETAIL F SCALE 1 2 DETAIL G SCALE 1 2 DIMENSIONS INCHES MILLIMETERS XCM7000 Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungs
5. INSTALLATION INSTRUCTIONS shown installed to 1 1 2 columns as example only Extra Large Dual Column Ceiling Mount CHIEF XCM7000 Our Mounts Your XCM7000 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipmen
6. M7000 Installation Instructions INSTALLATION NOTE The following procedure assumes that 2 UL Listed CPA or CMA ceiling plates not included and 2 extension columns not included have been properly installed following instructions provided with ceiling plates and extension columns The ceiling plates and columns should be installed approximately centered on mount with spacing between columns to be NO LESS than 18 See Dimensions drawings IMPORTANT The weight of the system should be evenly distributed across two ceiling plates NOTE Proceed to Attaching Mount to 1 1 2 NPT Column section or Attaching Mount to CPA Extension Column section as appropriate Attaching Mount to 1 1 2 NPT Column 1 Turn the array head FF upside down See Figure 1 2 Remove AND SAVE two buttonhead screws from array head See Figure 1 3 Remove and discard inner bracket from array head See Figure 1 oQ x2 Bottom of array head FF Inner bracket Figure 1 CAUTION WATCH FOR PINCH POINTS Do not place fingers between moveable parts 4 Turn array head upright See Figure 2 5 Turn adjustment bolt on top of array head to slide plate up and enlarge opening on front of array head See Figure 2 6 Insert lower set screw bracket HH into array head FF with three tabs towards sides and back See Figure 2 7 Fasten bracket HH into place in bottom of array head
7. ach interface bracket to lock display to ceiling mount See Figure 14 A LU Optional Display not shown Figure 14 2 Install back cover GG into four holes on back of both array heads FF See Figure 15 Display not shown Figure 15 10 Installation Instructions XCM7000 11 XCM7000 Installation Instructions USA International CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002455 Rev00 2014 Milestone AV Technologies www chiefmfg com 01 14 gt Uu 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
8. d See Figure 9 Installation Instructions XCM7000 2 While supporting both sides of display lower display onto center of ceiling mount hooking top of interface brackets onto front of ceiling mount See Figure 11 3 Raise the latch mechanism on both interface brackets to lock bracket in place See Figure 11 2 2 4 Latch mechanism Array heads display not shown for clarity Figure 11 Adjustments CAUTION Watch for pinch points Do not place fingers between moveable parts Height Adjustment and Leveling The ceiling mounts allow up to 2 inches total adjustment 1 Turn the adjustment bolt in the direction necessary to level or adjust height See Figure 12 2 Stop adjusting when the desired setting is reached Adjustment ots Figure 12 Tilt NOTE Two people will be required to adjust the tilt when the display is installed The interface brackets allow 7 6 to 20 tilt and can be locked at 7 6 5 0 5 10 15 and 20 tilt 1 Adjust tilt as required See Figure 13 2 The tilt may be locked using one 1 4 20 x 2 button head screw V and one 1 4 20 lock nut W per interface bracket See Figure 13 3 Repeat for remaining interface bracket Display not shown Figure 13 XCM7000 Installation Instructions OPTIONAL Security 1 OPTIONAL Add padlock not included to e
9. da Chiave esagonale Zeskantsleutel Cl t te hexagonale 09 Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguran a Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions XCM7000 TOOLS REQUIRED FOR INSTALLATION 5 32 included 2 1 2 or 13mm 3 16 M5 Interface Bracket Hardware Kit e e e 8 6 C 6 D 6 R 2 10 24 x 1 4 69 M4xi6mm M4x20mm M4x25mm 5 S 2 3 32 Q 2 74 d e Bottom coupling Used with 1 1 2 E 6 F 6 G 6 H 6 EN M5x20mm M5x25mm M xi6mm column system 60 amp 2 6 J 6 K 4 U 3 2 5 32 3 16 M8x20mm M8x30mm M8x50mm 3 9 S N 8 eq 2 M 8 i 1 4 20 L 8 Universal M5 750 344 500 h In ba V 2 750 323 250 washer 9 20 x2 labeled N 1 4 20 x 2 E es 4 AA 8 4 225 ERR Z 4 SP 5 16 x 3 4 End cap 1 4 20 x 1 2 5 16 e 1 2 4 DD 4 1 SZ 5 16x2 EE 4 T slot stud GG 2 Back cover KK 2 Interface bracket JJ 1 Mounting rail Lower set screw bracket XC
10. t or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located within the mounting system of the XCM7000 does not exceed a maximum weight capacity of 300 Ibs 136 1 kg WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors NOTE The XCM7000 dual column ceiling mounts are intended to be used with the UL Listed CPA extension columns and UL Listed CPA Ceiling Plates not included CPA330 CPA365 CPA395 The following UL Listed Chief ceiling plates WITHOUT swaged collars not included may also be used CMA330 CMA345 CMA395 SAVE THESE INSTRUCTIONS XCM7000 Installation Instructions DIMENSIONS COLUMNS SHOULD BE APPROXIMATELY CENT
11. teil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option C E d 4 Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabeca sextava
Download Pdf Manuals
Related Search