Da-Lite 80848 projection screen
Contents
1. INSTRUCTION BOOK FOR Motorized Scenic Roller Screen DA LITE Important Safety Instructions When using your video equipment basic safety precautions should always be followed including the following 1 Read and understand all instructions before using 2 Position the cord so that it will not be tripped over pulled or contact hot surfaces 3 If an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons Installation Before proceeding with the installation please read the installation and operating instructions thoroughly Make sure to recheck measurements of screen and hanger locations before installation Area must be clear for screen to operate With all lid sections removed from shipping container remove the screws holding the frame to the shipping container 2 per cross brace The screen can now be carefully lifted out of the container Method A The frame can be mounted to ceiling with 5 16 diameter2. Of Controller Red Out Of Controller Power Input Blue Common 240VAC 50HZ Brown Hot White Black 36 AMPS Green Yellow y Black Up Ground Brown Down Black Up Red Out Of Controller Brown Out Of Controller Motorized Scenic Roller Installation 120V 240V Wall Switch Wiring Diagram Front Back Of Of Wall Wall Switch Switch Optional RF Remote Red Up Connection Black Down White Common Not Used NOTE 20 24AWG wire recommended for connecting wall switch to sychronization controller IMPORTANT The wall switch terminal block can be connected inside the wiring compartment The controller does not need to be removed from the junction box unless an RF remote is being connected Use caution when removing the controller from the box as it is easily damaged Limit Switch Adjustment The stop positions of the screen are preset at the factory If adjustments are necessary the limit switch screws located at the end of each motor can adjust the stop positions Use a 5 32 hex key or a flat screwdriver Adjustments should be made in small increments by turning the adjustment screws a half turn at a time Refer to figure 3 Setting The Down Limit Position Screen Drops Too Far Left motor as viewed from audience side Turn the white limit switch screw clockwise to decrease the amou Right motor as viewed
3. Technologies LLC warrants certain Da Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you sp
4. both motors run the screen travels up too far the power to the motors have to deactivate the switch by hand To do this push down on the switch trigger see Figure 1 to release the switch and have someone run the screen down This safety switch is to prevent the screen from traveling too far and binding the motors should the motor limit switches fail rom audience side Turn the yellow limit ockwise to increase the amount of travel Right motor as viewed from audience side Turn the white limit switch screw counterc ockwise to increase the amount of travel After adjusting the limit screws on both motors run the screen up to test the s position is set top position Repeat until the desired Limit Switch Adjustment Yellow Up Limit Clockwise Less Up Travel Counterclockwise More Up Travel o o o o Motor 1 o Motor 2 oo a 80 White Down Limit Clockwise Less Down Travel Counterclockwise More Down Travel Top View Audience Side Figure 3 LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV
5. threaded rods Level frame from front to back and left to right Mount from all cross braces Figure 1 Suggested Method Of Installation Method A Secure To Ceiling t Ceiling ur A N Secure To Suit Cox Coo s Threaded Rod Cross Ens Ty 6 Cross Braces Not Furnished Front i Back he 15 gt Cable Safety Switch Trigger Figure 1 Electrical Installation Screen motors have been internally wired at Da Lite Wiring designated external is completed by installer conforming to local and national codes Refer to wiring diagram on next page Check for satisfactory condition by operating the screen Be prepared to stop screen Standard Duty Cycle 1 MIN 30 SEC ON 45 MIN OFF A CAUTION Excessive continuous operation may cause overheating and motors will shut off Let motors cool 10 to 15 minutes and continue test A ATTENTION Le fonctionnement continu et excessif peut provoquer une surchauffe et l arr t du moteur Laissez le moteur refroidir pendant 10 a 15 minutes et poursuivez le test Check the cables to make sure they are winding on the motor and roller pulleys properly Method B Hang from a pipe fly the screen Level frame from front to back and left to right Mount from all cross braces Figure 2 NOTE Motor pulley must clear pipe Chains must clear motor tubes Suggested Method Of Installation Method B F
6. ecific legal rights and you may also have other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite com www da lite com DL 0278 Rev 1 07 14 2014 Milestone AV Technologies LLC Printed in U S A 84222
7. from audience side switch screw clockwise to decrease the amou nt of fabric drop Turn the yellow limit nt of fabric drop After adjusting the limit screws on both motors run the screen down to test the stop position Repeat until th is set een Does Not Drop Enough of fabric drop gt Righ of fabric drop gt motor as viewed from audience side Turn limit switch screw counterclockwise to increase e desired position t motor as viewed from audience side Turn the white limit switch screw counterclockwise to increase the amount the yellow the amount ter adjusting the limit screws on both motors run the screen down to test the stop position Repeat until the desired position is set Do not adjust for more drop than what least 11 2 wraps of fabric must remain on the was ordered At roller Setting The Up Limit Position Screen Travels Up Too Far Left motor as viewed from audience side screw clockwise to decrease the a switch Right switch After adjusting the limi up to test the stop pos will be shut off You wil motor as viewed from audience side Turn screw clockwise to decrease the a ition If the screen safety stop switch will be activated and a Screen Does Not Travel Up Far Enough Left motor as viewed switch screw counterc Turn the yellow limit mount of travel the white limit mount of travel t screws on
8. lying Pipe A Ceiling Pipe To Suit Chain To Suit 6 Cross Braces Not Furnished Eye Bolts For Leveling Cross Brace A Not Furnished Front Y N Back C OR Safety Switch Trigger Figure 2 Screen Adjustment 1 With screen in complete unrolled position examine the screen surface carefully If fabric does not hang flat loosen the nuts on the eyebolts of the black clamps Adjust the wingnuts to pull or relax the fabric as needed Several clamp heights may be adjusted depending on the severity of the hang After adjustment tighten the nuts against the underside of the frame Caution stage hands and others to check area before lowering screen Do not bump screen with adders scenery etc Motorized Scenic Roller Installation 120V Wiring Diagram White Common Red U ed p Black Down Green Ground Brown Out Of Controller Red Out Of Controller Safety Switch White Common Power Input 120VAC 60HZ Black Hot White Green Ground White Common 240V Wiring Diagram NOTES 1 FUSE RATED 15A 250VAC Blue Common Black Down hite Common Red Up Black Dow Red Out Of Controller Brown Out Of Controller Blue Common Brown Out Safety Switch
Download Pdf Manuals
Related Search